Philips MCD710 Service Manual

DVD Micro theatre

MCD710

all versions

TABLE OF CONTENTS

Service Aids ..................................................................................1-1

Info. about lead-free soldering.......................................................1-1

Service Instruction ........................................................................1-1

CD Playability Check .............................................................2-1..2-3

Disassembly digram ...............................................................3-1..3-3

Software version check and upgrading .........................................4-1

Block diagram ................................................................................5-1

Wiring diagram .............................................................................6-1

Tuner Board

circuit diagram ..........................................................................7-1

layout diagram ..........................................................................7-2

VFD Board

circuit diagram ..........................................................................8-1

layout diagram ..........................................................................8-2

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

...

AMP/POWER Board

circuit diagram................................................................... 9-1...9-3

layout diagram ...........................................................................9-4

MPEG Board

circuit diagram. .............................................................. 11-1..11-6

layout diagram ........................................................................

Exploded view diagram .................................................................. 12-1

Service parts list ....................................................................13-1..13-5

11-7

Published by LX 0835 Service Audio Subject to modification

Version 1.4

3141 785 32074

SERVICE AIDS

1-1

Service Tools:

Universal Torx driver holder .................................4822 395 91019

Torx bit T10 150mm ...........................................4822 395 50456

Torx driver set T6-T20 .........................................4822 395 50145

Torx driver T10 extended .....................................4822 395 50423

All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via a wrist wrap with resistance. Keep components and tools also at this potential.

WARNING

Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified, be used

Safety components are marked by the symbol !.

Compact Disc:

SBC426/426A Test disc 5 + 5A ...........................4822 397 30096

SBC442 Audio Burn-in test disc 1kHz .................4822 397 30155

SBC429 Audio Signals disc .................................4822 397 30184

Dolby Pro-logic Test Disc ....................................4822 395 10216

ESD

CLASS 1

LASER PRODUCT

Lead free

CD PLAYABILITY CHECK

Customer complaint

"CD related problem"

check playability

2 -1

Set remains closed!

playability

ok ?

Play a CD

for at least 10 minutes

check playability

playability

ok ?

"fast" lens cleaning

check playability

playability

ok ?

For flap loaders (= access to CD drive possible) cleaning method

is recommended

Standard repair procedure

clean the lens

check playability

playability

ok ?

check "EYE-Pattern"

return set

add Info for customer

"SET OK"

return set

1 - 7

For description - see following pages

replace Signal Processor

return set

EYE-Pattern

ok ?

check Laser current

Laser current

ok ?

check CD Drive offsets

CD Drive offsets

ok ?

replace CD Drive

return set

replace CD Drive

return set

replace CD Drive

return set

CD PLAYABILITY CHECK

2-2

PLAYABILITY CHECK

For sets which are compatible with CD-RW discs

use CD-RW Printed Audio Disc....................7104 099 96611

TR 3 (Fingerprint) TR 8 (600µ Black dot) maximum at 01:00

• playback of these two tracks without audible disturbance playing time for: Fingerprint ≥10seconds

Black dot from 00:50 to 01:10

• jump forward/backward (search) within a reasonable time

For all other sets

use CD-DA SBC 444A..................................4822 397 30245

TR 14 (600µ Black dot) maximum at 01:15 TR 19 (Fingerprint) TR 10 (1000µ wedge)

• playback of all these tracks without audible disturbance playing time for: 1000µ wedge ≥10seconds

Fingerprint ≥10seconds Black dot from 01:05 to 01:25

• jump forward/backward (search) within a reasonable time

LIQUID LENS CLEANING

Before touching the lens it is advised to clean the surface of the lens by blowing clean air over it. This to avoid that little particles make scratches on the lens.

Because the material of the lens is synthetic and coated with a special anti-reflectivity layer, cleaning must be done with a non-aggressive cleaning fluid. It is advised to use “Cleaning Solvent B4-No2”, available with codenumber 4822 389 10026.

The actuator is a very precise mechanical component and may not be damaged in order to guarantee its full function. Clean the lens gently (don’t press too hard) with a soft and clean cotton bud moistened with the special lens cleaner.

The direction of cleaning must be in the way as indicated in the picture below.

CUSTOMER INFORMATION

It is proposed to add an addendum sheet to the set which informs the customer that the set has been checked carefully - but no fault was found. The problem was obviously caused by a scratched, dirty or copy-protected CD. In case problems remain, the customer is requested to contact the workshop directly. The lens cleaning (method 3) should be mentioned in the addendum sheet.

The final wording in national language as well as the printing is under responsibility of the Regional Service Organizations.

FAST LENS CLEANING (dry brush)

Use lens cleaning CD

SBC AC300...........................................9082 100 00043

Insert the lens cleaning CD, press PLAY and follow the voice guide´s instructions on the CD.

Sanyo DA12T3

CD Drive

VCC

VREF

1800

+5V_HF

VrefCD10

B C

GND

Laser power control

100n

2878

470n

2876

3821

3823

2880

33p

+5V

BC807-40

7879

3817

47R

3820

4R7

47R

3819

2879

2877

47u

7811-A

LM358D

10K

3822

47R

3818

2841

100n

47n

2869

+5V_HF

LASER DIODE

U >250mV

->Laser damaged !

4,6V

3,3V

3,9V

0,17V

Sanyo DA12T3

HF-Amplifier

680R

3905

3903 3K3

BC847B

7877

47n

2818

1K5

3902

470R

3893

+3.3V

2K2

3908

10K

3923

BC847B

7878

BC847B

7876

4n7

2813

3896

100R

220u

2885

2881

560p

47n

2887

560R

3901

2883

470n

2817

4u7

3n3

2814

3898 220R

3895

27K

470n

2884

+3.3V

3909

820R

3907

100R

3920

33K

3897

2882

82p

3K3

3904

2K7

3899

3906

470R

+5V_HF

HFIN

VrefCD10

100p

28152816

22n

to 3826,3827

VREF GE

VDDA1

VRIN

VSSA1

ISLICE

HFIN

HFREF

IREF

CD_DA: 0V / CD_RW: 3V

Σ (A-D)

800mVpp

TB = 0.5µs/div

EYE-PATTERN

1,8V

1,2V

2,4V

2,6V

0,65V

CD PLAYABILITY CHECK

2-3

EYE-PATTERN SIGNAL – JITTER MEASUREMENT

Measure the signal on the input of the Signal processor using an analog oscilloscope. Please find the exact measuring point in your Service Manual.

See below examples of the signal. Amplitude should read at least 700mVpp using SBC444A.

CD DRIVE – LASER CURRENT MEASUREMENT

The laser current can be measured as a voltage drop on a resistor. The resistor is marked in every Service Manual. The value depends on the type of CD drive.

typical value most probably defect

VAMxxxx : 150-230mV ≥350mV MCDxx : 170-230mV ≥300mV DA1x : 210-250mV ≥350mV DA2x : 175-200mV ≥250mV Use SBC444A (CD-DA) for measurement.

If the oscilloscope shows a signal like the ‘bad’ one, and/or the amplitude decreases within 1 minute - the CD drive has to be replaced.

good

bad

CD DRIVE – OFFSET MEASUREMENT

The photodiodes of the CD-drive may have an offset. These offsets have to be compensated by the signal processor. High offsets can lead to poor playability of some CDs (skipping tracks).

To measure the offset values, start the Service Test Program - section “Focus Test” without a CD.

The offsets can be measured with a DC Millivoltmeter directly on the connector (see drawing below). Pin numbering varies from drive to drive.

The values from diode A-D should read 0±10mV. Diodes E and F are less critical.

If one of the offsets is higher than ±10mV the CD drive has to be replaced. Otherwise replace the Signal Processor.

3-1

Disassembly Diagram

A.Open the top cover

A1. Loosen screws

A. Remove TOP cover

3×15PA (4PCS)

3-1

C. Loosen screw 3×6FMTT(1PCS),remove turner board

D.Cut off 2 PCS wire tie

B. Loosen screws 3×10FA(7PCS),then remove back cover of output jack

3 - 2

E.Loosen screws 3×10PA(1PCS),then remove AMP board

F.Loosen screws 3×15BA(4PCS), then remove mechanism core

G.Loosen screws3×6PT(2PCS),then remove decoder board

I.Loosen screws 3×10BA(2PCS),and remove top cover

3 - 3

I. Loosen screws 2.6×8BA(8PCS),and remove display board

3 - 3

Loosen screws 2.6×8BA(3PCS) and remove volume board K.Loosen screws 2.6×8BA(4PCS), remove USB and earing socket

Software Version Check & Upgrade

Upgrade software

1.Downloading the software form the website that Philips supports

http://www.philips.com/support

2.Put in the Software CD Disc or USB,when it is loading, the TV screen shows as below:

Upgrade File detected

Upgrade? Press PLAY to start

Upgrading

Waiting half to one minute,till the TV screen showing disappear. Turn off electrical source and reopen.

3.Press SYSTEM on the remote open menu, press Left or Right to select “Preference

Page”, now TV screen shows as below:

--Preference Page-TV type PAL Audio CHI English

Subtitle CHI French Disc menu CHI Spanish

Parental Chinese Japanese

Default Korean

Russian

Tjai

4-1

Press Up or Down to select “Default” on remote, Press OK to exit reset. Software upgrade finish.

Software check

Input password “811502” on remote, TV screen showing as below:

MCD710 / xxxx

Ver :

mm dd yyyy

Date

hh : mm : ss

Time Region code

CPU version check

1.Keep press PLAY/PAUSE and STOP buttons,plug into the power cord at one time, TV showing as below:

MCD710 Vxx

SET BLOCK DIAGRAM

5 - 1

6 - 1

SET WIRING DIAGRAM

+ 24 hidden pages