Philips LX8200SA User Manual
abc
b
0.31"
(8mm)
Quick Use
Quick Use
Guide
Guide
Connecting Speaker Cable
front
right
Centre
LX
8200SA
front
left
Helpful Hints:
You can listen to normal TV
broadcast channels through the
home cinema sound system from
such an audio connection.
When listening to TV programmes,
you have to set the DVD system
to TV/ AV mode in order for the
sound to be heard.
☞
AUDIO OUT
L
R
Helpful Hints:
If your TV is not equipped with a SCART
connector, connect your TV through the
corresponding CVBS A or S-Video B output.
Use Pr/ Cr Pb/Cb Y jacks C connection if your TV
can accept progressive signals (Progressive Scan
TV).
Notes: On the TV
- The CVBS jack may be labeled as Video, Composite or
Baseband and is usually yellow.
- The S-Video In jack may be labeled as Y/C, S-Video or
S-VHS.
- The Pr/ Cr Pb/ Cb Y jacks may be labeled as
Component Video In or YUV and are usually red, blue
and green.
12nc: 3139 115 22491
Use this simple and quick way to
watch your favourite DVD movie
and enjoy your Home Cinema
experience!
☞
SPEAKER SYSTEMS (6Ω)
LCRSLSR
+
Surround
right
Recommended Speaker Setup
CDR
A
CENTER
DIGITAL
OUT
+
SURROUNDFRONT CENTER
OUT
DIGITALINWOOFER
LINE OUT
AUX
TV
LINE
IN
IN
OUT
AUDIO
VIDEO OUT
CVBS
L
R
S-VIDEO
Pr/Cr
Pb/Cb
Y
FM 75
C
Ω
SCART OUT
MW
FM/MW
ANTENNA
B
Surround
left
Subwoofer
AUDIO
INPUT
Connect the DVD system and subwoofer to the power outlets only
after you have finished hooking up everything.
DISC
OK
SYSTEM
MENU
1 2 3 4
AV IN
STANDBY-ON
ECO POWER
DVD VIDEO /SACD DIGITAL SURROUND SYSTEM
OPEN/CLOSE
SOURCE
SURROUND
SOUND
iR
SENSOR
VOLUME
Make sure your DVD system and TV are
connected and turned on!
ö Turning on the power and listening to preset radio stations
1 “AUTO INSTALL- PRESS PLAY” will appear on the display. If not, press and hold ÉÅ on the system.
2 Press ÉÅ on the system again to start installing all available radio stations.
3 Once completed, the last tuned radio station will play. Press 1 2 to select a preset radio station.
To tune to a non-preset radio station, press S T briefly and repeatedly.
ö Playing a disc
1 With the DVD system’s power on, press DISC on the remote control.
2 Turn on the TV power and set to the correct Video In channel or
Audio/ Video mode. The DVD system’s blue screen will show on the TV.
The TV’s Video Input channel may be called AUX or AUXI LIARY IN, AUDIO/VIDEO or A/ V IN,
EXT 1 or EXT 2, etc. These channels are often near channel 00. See your TV manual for details.
DVD VIDEO /SACD DIGITAL SURROUND SYSTEM
STANDBY-ON
ECO POWER
OPEN/CLOSE
SOURCE
3 Press OPEN/CLOSE on the system and load a disc, then press OPEN/CLOSE again to close
the disc tray.
4 Playback will start automatically. If not, press ÉÅ.
If a disc menu appears, use 3 4 1 2 to make the necessary selection, then press OK. Or, use the numeric
keypad on the remote control to select features. Follow the instructions given on the disc menu.
5 During playback, you are able to change certain operations or features (for example, change the subtitle
language, play in slow motion speed, etc.). Press SYSTEM MENU on the remote control, then use 3 4
1 2 to select your preferred options and press OK to confirm. To remove the menu bar, press
SYSTEM MENU again.
Please refer to the owner’s manual “Special DVD/ VCD features” for more information.
6 To stop playback, press Ç.
SURROUND
SOUND
iR
VOLUME
SENSOR
POWER
ON/OFF
OPEN/CLOSE
DISC 3
Region Codes
DVDs must be labeled for ALL regions or for Region 2 in order to play on this DVD system.
ö Playing other equipment connected to your DVD system
1 To use your DVD system’s home cinema surround capabilities, connect other
equipment and select the correct input source.
Please refer to the user’s manual “Connecting Additional Equipment” for more
information.
2 Turn on and / or press PLAY on the equipment to start playback.
If necessary, connect the Video Output of the connected equipment (VCR or laser disc
player) to TV for viewing purposes.
Detailed playback features and additional functions are described in the
accompanying user’s manual.
LX8200SA
DIGITAL
IN
AUX
IN
TV
IN
Connect ...
CD Recorder
"DIGITAL OUT"
➜
Laser disc player
"AUDIO OUT"
➜
Televeision
"AUDIO OUT"
➜
VCR /
ALL
Select input source
from the remote
control
AUX/D I
Press to select "DI".
➜
AUX/D I
Press to select "AUX".
➜
TV/AV
Press .
➜
2
Loading...