Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without
the prior permission of Philips.
Published by Helen-RY 1207 Service Audio Printed in The Netherlands Subject to modification
One must treat all sets from 1.1.2005 onwards, according
next rules.
Important note
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
x Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste within
workshops should be avoided because paste is not easy
to store and to handle.
x Use only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
o To reach at least a solder-temperature of 400°C,
o To stabilize the adjusted temperature at the
o To exchange solder-tips for different applications.
x Adjust your solder tool so that a temperature around
360°C
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400°C otherwise
wear-out of tips will rise drastically and flux-fluid will be
destroyed. To avoid wear-out of tips switch off un-used
equipment, or reduce heat.
x Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed
solder alloy types (leaded and lead-free). If one cannot
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
: In fact also products a little older can also
solder-tip
– 380°C is reached and stabilized at the solder
x Use only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
companies.
xSpecial information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering always use highest lead-free
temperature profile, in case of doubt)
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
pack) to protect the IC against moisture. After
opening, dependent of MSL-level seen on
indicator-label in the bag, the BGA-IC possibly
still has to be baked dry. This will be
communicated via AYS-website.
Do not re-use BGAs at all.
x For sets produced before 1.1.2005, containing
leaded soldering-tin and components, all needed
spare-parts will be available till the end of the
service-period. For repair of such sets nothing
changes.
x On our website:
www.atyourservice.ce.Philips.com
You find more information to:
BGA-de-/soldering (+ baking instructions)
Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.
Page 19
2-1
EN Before using your product, read all accompanying safety
information
DA Læs alle medfølgende sikkerhedsoplysninger, inden du
tager produktet i brug
DE Lesen Sie vor Verwendung dieses Produkts alle
begleitenden Sicherheitsinformationen
EL ƑƱƩƭ ƷƱƧƳƩƬƯưƯƩƞƳƥƴƥ ƴƯ ưƱƯƺƼƭ, ƤƩơƢƜƳƴƥ ƼƫƥƲ ƴƩƲ
ươƱƥƷƼƬƥƭƥƲ ưƫƧƱƯƶƯƱƟƥƲ ơƳƶƜƫƥƩơƲ
ES Antes de usar el producto, lea toda la información de
seguridad adjunta
FI Lue kaikki turvallisuustiedot ennen tuotteen käyttöä
FR Avant d’utiliser votre produit, lisez l’intégralité des
consignes de sécurité jointes
IT Prima di utilizzare il prodotto, leggere tutte le relative
informazioni sulla sicurezza
NL Lees voordat u het product gaat gebruiken eerst alle
bijbehorende veiligheidsinformatie
NO Les all vedlagt sikkerhetsinformasjon før du bruker
produktet
PT Antes de utilizar o produto, leia todas as informações de
segurança que o acompanham
SV Innan du använder produkten ska du läsa all tillhörande
säkerhetsinformation
TR Ürününüzü kullanmadan önce ilgili tüm güvenlik bilgilerini
okuyun
CS Pŏed použitím produktu si pŏeĈtĖte doprovodné
bezpeĈnostní informace
HU A termék használata elʼntt alaposan olvassa el a mellékelt
biztonsági tudnivalókat
PL Przed rozpoczĔciem korzystania z produktu naleůy
zapoznaĂ siĔ z informacjami dotyczĀcymi bezpieczeļstwa
RO Înainte de a utiliza acest produs, citiŗi toate informaŗiile de
siguranŗþ care îl însoŗesc
SK Pred použitím produktu si preĈítajte všetky sprievodné
bezpeĈnostné informácie
User manual
UK only
Page 20
1
2-2
EN Connect the home theater
DA Tilslut hjemmebiografen
DE Anschließen des Home
Entertainment-Systems
EL ƓƵƭƤƝƳƴƥ ƴƯ home cinema
ES Conecta el sistema de cine en casa
FI Kotiteatterin liitännät
FR Connecter les enceintes au Home Cinéma
IT Collegamento del sistema Home Theater
NL Sluit de home cinema aan
STS3001
FRONT
FRONT
RIGHT
LEFT
FRONT
CENTER
REAR
RIGHT
REAR
LEFT
SUB
WOOFER
NO Koble til hjemmekinoanlegget
PT Efectuar as ligações ao sistema de cinema em casa
SV Anslut hemmabiosystemet
TR Ev sinemasını baĚlayın
CS Pŏipojte domácí kino
HU A házimozi csatlakoztatása
PL PodãĀczanie zestawu kina domowego
RO Conectaŗi sistemul home theater
SK Pripojenie k domácemu kinu
SUB
WOOFER
FRONT
LEFT
FRONT
CENTER
FRONT
RIGHT
FRONT
RIGHT
FRONT
LEFT
FRONT
CENTER
REAR
RIGHT
REAR
LEFT
REAR
LEFT
REAR
RIGHT
SUB
WOOFER
Page 21
HDMI OUT (ARC)
2-3
AC MAINS~
HDMI (ARC)
Page 22
X2
2-4
EN Switch on the home theater
DA Tænd for hjemmebiografen
DE Einschalten des Home
Entertainment-Systems
EL ƆƭƥƱƣƯưƯƩƞƳƴƥ ƴƯ home cinema
ES Enciende el sistema de cine en casa
FI Virran kytkeminen kotiteatteriin
FR Mettre sous tension le Home Cinéma
IT Accensione del sistema Home Theater
NL Schakel de home cinema in
1
NO Slå på hjemmekinoanlegget
PT Ligar o sistema de cinema em casa
SV Sätt på hemmabiosystemet
TR Ev sinemasını açın
CS ZapnĖte domácí kino
HU A házimozi bekapcsolása
PL WãĀczanie zestawu kina domowego
RO Porniŗi sistemul home theater
SK Zapnutie domáceho kina
2
Page 23
3
2-5
EN Complete the fi rst time setup
DA Fuldfør den indledende opsætning
DE Abschließen der Ersteinrichtung
EL ƐƫƯƪƫƧƱƾƳƴƥ ƴƧ ƱƽƨƬƩƳƧ ƣƩơ ưƱƾƴƧ ƶƯƱƜ
ES Finaliza la confi guración inicial
FI Ensiasennuksen suorittaminen loppuun
FR Effectuer la confi guration initiale
IT Completamento della confi gurazione iniziale
NL Voltooi de eerste installatie
1
NO Fullføre den første konfi gureringen
PT Executar a confi guração inicial
SV Slutför förstagångsinställningen
TR īlk kullanım öncesi kurulumunu tamamlayın
CS DokonĈili jste nastavení pŏi prvním zapnutí
HU Az elsʼn üzembe helyezés
PL Pierwsza konfi guracja
RO Realizaŗi prima confi gurare
SK DokonĈenie prvého nastavenia
EN Use your home theater
DA Brug af din hjemmebiograf
DE Verwenden des Home
Entertainment-Systems
EL ƗƱƧƳƩƬƯưƯƩƞƳƴƥ ƴƯ home cinema
ES Uso del sistema de cine en casa
FI Kotiteatterin käyttäminen
FR Utiliser votre Home Cinéma
IT Utilizzo del sistema Home Theater
NL Uw home cinema bedienen
NO Bruke hjemmekinoanlegget
PT Utilizar o sistema de cinema em casa
SV Använda hemmabiosystemet
TR Ev sinema sisteminin kullanılması
CS Použití domácího kina
HU A házimozi használata
PL Korzystanie z zestawu kina domowego
RO Utilizaŗi sistemul home theater
SK Používanie domáceho kina
Philips offers, register your product at
www.philips.com/welcome.
Main unit
This section includes an overview of the main unit.
Disc compartment
a
b
Display panel
c
(Open/Close)
Open or close the disc compartment, or
eject the disc.
d
(Play/Pause)
Start, pause or resume play.
Remote control
This section includes an overview of the remote control.
1
2
3
4
5
6
7
8
9
14
15
16
17
e
SOURCE
Select an audio or video source for the home
theater.
f
(Standby-On)
Switch the home theater on or to standby.
10
11
12
13
18
19
20
21
Page 27
(Standby-On)
a
Switch the home theater on or to standby.
When EasyLink is enabled, press and hold for
at least three seconds to switch all connected
HDMI CEC compliant devices to standby.
(Home)
b
Access the home menu.
c Source buttons
DISC/POP-UP MENU : Switch to disc
source.Access or exit the disc menu
when you play a disc.
RADIO : Switch to FM radio.
AUDIO SOURCE : Select an audio input
source.
d
e
BACK
Return to a previous menu screen.
In radio mode, press and hold to erase
the current preset radio stations.
Navigation buttons
Navigate menus.
In radio mode, press left or right to start
auto search.
In radio mode, press up or down to tune
the radio frequency.
2-9
o
p
q
r
s
t
u
OPTIONS
Access more play options while playing a
disc or a USB storage device.
In radio mode, set a radio station.
(Play)
Start or resume play.
(Pause)
Pause play.
(Mute)
Mute or restore volume.
AUDIO
Select an audio language or channel.
SUBTITLE
Select subtitle language for video.
Color buttons
Select tasks or options for Blu-ray discs.
f
OK
&RQÀUPDQHQWU\RUVHOHFWLRQ
g
h
/ (Previous/Next)
Skip to the previous or next track,
FKDSWHURUÀOH
In radio mode, select a preset radio station.
(Stop) / (Eject/Open/Close)
Stop play.
Press and hold for three seconds to open or
close the disc compartment, or eject the disc.
i
/ (Fast Backward / Fast Forward)
Search backwards or forward. Press
repeatedly to change the search speed.
j +/- (Volume)
Increase or decrease volume.
k
SOUND SETTINGS
Access or exit sound options.
l
Alphanumeric buttons
Enter values or letters (using SMS style entry).
REPEAT
m
Select or turn off repeat mode.
n
TOP MENU
Access the main menu of a disc.
Page 28
3-1
Mechanical and Dismantling Instructions
Dismantling Instruction
The following guidelines show how to dismantle the player.
Step1: Remove 6 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Detailed information please refer to the model set.
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Turn on the power button,then press open button to dismantle front door.Please kindly note that power off as soon
as front door is out of machine.
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 1
Please kindly note that dismantle the front door
assembly carefully to avoid damage tray and the front door.
Figure 2
Page 29
Mechanical and Dismantling Instructions
Dismantling Instruction
3-2
Detailed information please refer to the model set.
:Dismantle Front Panel, disconnect the connectors (XS604 XPS605 ,XP8), need release 2 snaps of Front Panel & 2 snaps
Step3
,
of bottom cabinet , then gently pull the Panel out from the set. (Figure 3)
Figure 3
Step4
: Dismantle Front Control Board,remove 5 screws (Figure 4
)
Figure 4
Step5
: Dismantle Loader, disconnect the 3 connectors (J11, XP7,J12
that connects the loader and the bottom cabinet. (Figure 5)
) aiming in the below figure, and remove 2 screws
Figure 5
Page 30
3-3
XP7
J11
J12
XP6
XP9
XP1
XP13
XP604
XP35
XP701
XS703
XP502
XP501
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
Step6
: Dismantle Main Board, first disconnect 6
screws. (Figure
: Dismantle Power Board, disconnect the connectors
Step7
Step8: Dismantle Amplifier Board, first disconnect connectors(XP701,),and then remove
(Figure 5/6)
5/6)
connectors(XP6,XP9,XP1,XP13,XP35,XP604
(XP502,XP501), then remove
XS703
CN502
5
screws.(Figure 5/6)
4
), and then remove
4 screws
Figure 6
Page 31
4-1
Software upgrade
Software upgrade method:
1.Copy the bin file as "HTS3541M2_XX.bin".
2.Then use the file to burn the upgrade CD-R/CD-RW.
3.Put the CD in the tray ,let the player loading the disc.
4.If the CD is correct ,it will display the Upgrade Menu ,press the PLAY key on the remote
control to start upgrade
5.Afer a while, the tray will open automatically ,but must not power off the player.
6.Don't power off ,wait until the player reset automatically ,the whole upgrade process may
need 2 minutes .HTS will auto standby after complete upgrade.
if you upgrade with USB device:
1.step1 is same with DISC upgrade;
2.Copy the renamed bin file(upgrade file) to the root menu of USB device.
3.connect the USB device to HTS ,and switch to USB source;
4.The rest is same to step 4,step 5 and step 6 with DISC upgrade.
Caution: The set must not be power off during
upgrading, Otherwise the Main board will be
damaged entirely.
Page 32
VFD No display on Front Control Board
VFD No display on
Front Control Board
Go
Check every supply voltage on Main Board
whether normal or not.
(XP8 PIN4:-24V, PIN6: +5V, PIN5: 12V)
Yes
Check voltage -24V, +5V,+12V on Power
Board at CN502 position and Front Control
Board at XP2 PIN11:-24V PIN10:+12V
PIN9:+5V
Yes
Check the power key S608, open/closed key
K138, source key K135, paly/pause key
K136 on Front Board whether work normally
or not
Yes
Check Front Control Board signals at XP2
Pin8 VSCLK, Pin7 VSDA,Pin6 VSTB
Check whether bad solder exists on XP2 on
Front Control Board and U135 of VFD
Yes
Yes
Yes
Replace U135 or VFD
5-1 Trouble shooting Chart
No
Refer to XP501 on Power Board
No
Fix the connection XP2 on Front
Control Board and XP8 on Main Board
No
Replace MCU U4 on Main Board, or
replace the Main Board
No
Check the XP2 ON Front Control Board Pin6,
7, 8 arrive the condition IC U135 PIN 7,9,1 0
No
Correct connection
Page 33
keys do not work
keys do not work
Go
Check voltage +5V on Front Board U135
PIN38
Check Front Control Board signals at XP2
Pin8 VSCLK, Pin7 VSDA,Pin6 VSTB
Yes
Yes
Replace U135 on Front Board
5-2 Trouble shooting Chart
No
No
Fix the connection XP2 to XP8 on Main
Board
Replace U4 on Main Board, or
replace Main Board
Page 34
Remote control does not work
Remote control
does not work
Go
Check battery of remote control whether
exhausted or not.
No
Check power supply of IR601 on Front
Control Board whether normal or not
XP2 Pin6 :+5V
Yes
Replace IR601
5-3 Trouble shooting Chart
Yes
No
Replace the battery for remote
control
Check the +5V net on Front Control
Board to Main Board XP8
Page 35
No audio output
Check voltage +34.5V (34V for HTS3564)
(41V for HTS3251) for whether normal or
not at on Amplifier Board
Check the 24Pin FFC connection XP13 on
Main Board and XP702 on Amplifier Board
whether right or not between Main Board
and Amplifier Board
Check the control signal whether right or
not at the U8 Pin6, Pin7 on Main Board
and the signal at the XP13 Pin15 Pin16
Pin3
Replace Amplifier Board
No audio output
Go
Yes
Yes
Yes
5-4 Trouble shooting Chart
Check XP13 Pin 14&16 3.3V on Main
No
Board whether normal or not
Yes
Refer to XP501 on
No
No
Power Board
Replace U8 on Main Board or
replace Main Board
Page 36
No video output
5-5 Trouble shooting Chart
No video output
Go
Check L452, R616 whether right on Main
Board
Yes
Check the video signal whether
right at U7: PIN B18 or R615
No
Replace Main IC or Main Board
No
Add L452, R616
Page 37
Can’t read disc or can’t open the disk door
Can’t read disc or can’t
open the disk door
Go
Check loader work normally or not
Yes
Check 45Pin, 8Pin, 4Pin cable from
Main Board to Loader connect right or
not
Yes
Replace Loader
、
5-6 Trouble shooting Chart
No
Check XP7 on Main Board
No
Fix 45Pin, 8Pin, 4Pin cable
Page 38
Tuner FM does not work
Tuner FM does not work
Check voltage at Q28 C electrode
(+5V) on Main Board whether normal
or not
Go
Check voltage +3.3V at Tuner
module (TUN1 Pin8) whether right or
not
Yes
Check Tuner module TUN1 Pin11,
Pin12 normal or not
Yes
Yes
Check the U8 PIN25, PIN26, I2C
output on Main Board normal or not
Yes
Replace main Board
5-7 Trouble shooting Chart
No
No
No
No
Refer to Power Board XP501
Check Main Board tuner power supply
circuit.
Change the Tuner module
Check Main Board U5 power
supply circuit
Page 39
AUX in does not work
AUX in does not
work
Go
Check voltage at U27 PIN16:12V on Main
Board whether normal or not
Check Main Board U27 Pin4, Pin11 signal
input whether right or not
Yes
Check U27 74HC4052 whether
broken
Replace U27 74HC4052
Yes
or not
Yes
5-8 Trouble shooting Chart
No
Refer to Power Board XP501
No
Check AUX IN connector
No
Check Main Board U4
Page 40
MP3 Link does not work
MP3 Link does
not work
Go
5-9 Trouble shooting Chart
Check signal at XS605 PIN3:MP3_R
PIN1:MP3_L ON front board whether normal or
not
Yes
Check Main Board U18 74HC4052 PIN2,
PIN15 L/R signal input right or not
Yes
Check voltage at U18 74HC4052
PIN16,VDD +12V, on Main Board
Whether normal or not
Yes
Check U27 74HC4052 whether broken
or not
Yes
Replace U27 74HC4052
No
No
No
Refer to Main Board XP604
No
Check Main Board C358, C349, R340,
R457,
Refer to Power Board XP501
Check Main Board U4
Page 41
COAX in does not work
COAX in does
not work
Go
Check voltage at U27 PIN6/PIN23:3.3V on
Main Board whether normal or not
Yes
Check Main Board U27 CS8416 PIN2 input
signal whether normal or not
Yes
Check U27 CS8416 whether broken.
or not
Yes
Replace U27 CS8416
5-10 Trouble shooting Chart
No
No
No
Refer to Power Board XP501
Check Main Board C360,L11
Check Main Board U8
Page 42
Karaoke in does not work
Karaoke in does
not work
Go
Check signal at XS605 PIN5: MIC_in
signal from front board normal or not
Yes
Check Main Board U18 74HC4052 PIN5,
PIN14 L/R signal input right or not