Philips HTS3375/55 Schematic
1 - 1
Service
Service
DVD Home Theater System
HTS3375/55
Service
Service
Service
Service Manual
TABLE OF CONTENTS
Location of PCB Boards ............................................ 1-2
Versions Variation ...................................................... 1-2
Specifications ............................................................ 1-3
Measurement Setup .................................................. 1-4
Service Aids .............................................................. 1-5
ESD & Safety Instruction .......................................... 1-6
Lead-free soldering Information ................................ 1-7
Setting procedure & Repair Instructions........................ 2
Disassembly Instructions & Service positions .............. 3
Block & Wiring Diagram ................................................ 4
DISP+LED+VOL Board.................................................. 5
MAIN+Y.U.V Board........................................................ 6
Power Board .................................................................. 7
MP3 IN+MIC Board........................................................ 8
Mechanical Exploded View & Part List.......................... 9
Revision List ................................................................ 10
©
Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by SL0907 Service Audio Printed in The Netherlands Subject to modification
Chapter
GB
3141 785 33491
Version 1.1
1 - 2
LOCATION OF PCB BOARDS
VERSION VARIATION:
Type/Versions
Features
HTS3375
Output Power - 1000W
Voltage (110~127V)
Voltage (220~240V)
MAIN+Y.U.V Board
DISP+LED+VOL Board
MP3 IN&MIC Board
Type/Versions
Board in used
HTS3375
C
C
C
/55
SERVICE SCNARIO MATRIX:
/55
x
x
x
*C = Component Level Repair
MP3 IN & MIC PCB
POWER PCB
MAIN PCB
Y. U .V PCB
LED PCB
DISPLAY PCB
VOLUME PCB
Power Board
C
1 - 3
SPECIFICATIONS
Playback media
DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R DL, CDR/CD-RW, AudioCD, Video CD/SVCD, Picture CD, MP3-CD,
WMA-CD, DivX-CD, USB ash drive
Amplifier
Total output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ......
Home theatre mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 W RMS (6 X 167)
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Hz ~ 20 kHz
Signal-to-noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 60 dB (A-weighted)
Input sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ......
............................................................................AUX1: 400 mV
............................................................................AUX2: 400 mV
MP3 LINK . .. . .. ... . .. . .. ... . .. ... . .. . .. ... . .. . .. ... . .. . .. ... . .. ... . .. . .. ... . .. . 250 mV
Disc
Laser Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Semiconductor
Disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12cm / 8cm
Video decording . . . . . . . . . . . . . . . . MPEG1/ MPEG2 / DivX / DivX Ultra
Video DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 bits, 108 MHz
Signal system . .. ... . .. ... . .. ... . .. ... . .. ... . .. ... . .. ... . .. ... . .. ... . .. PAL / NTSC
Video S/N .......... ..... .................. ..... .................. ................. 56 dB
Audio DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 bits / 96 kHz
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ......
............................................................ 4 Hz - 20 kHz (44.1 kHz)
............................................................... 4 Hz - 22 kHz (48 kHz)
............................................................... 4 Hz - 44 kHz (96 kHz)
PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IEC 60958
Dolby Digital ..... ........ ........ ..................... IEC 60958, IEC 61937
DTS .......... ..... .................. ..... ................. IEC 60958, IEC 61937
Radio
Tuning range .......... ..... ............ FM 87.5-108 MHz (50/100 kHz)
26 dB quieting sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 22 dBf
IF rejection ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 60 dB
Signal-to-noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 50 dB
Harmonic distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 3%
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . FM 180 Hz~10 kHz / ±6dB
Stereo separation . .. . .. ... . .. . .. ... . .. ... . .. . .. ... . .. . .. ... FM 26 dB (1 kHz)
Stereo Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 29 dB
USB
Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hi-Speed USB (2.0)
Class support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
............................................... UMS (USB Mass Storage Class)
File system ..... ........ ........ ....................... FAT12, FAT16, FAT32
Main Unit
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110-127V/220-240V;
.................................................................. ~50-60Hz switchable
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 W
Standby power consumption . .. ... . .. ... ... . .. ... ... . .. ... ... . .. ... ... . < 1 W
Dimensions (WxHxD) . .. .. ... ... ... ... ... .. ... ... ... 360 x 57 x 331 (mm)
Weight .......... ..... .................. ..... .................. ..... .............. 3.01 kg
Speakers
System . . . . . . . . . . . . . . ............................................. full range satellite
Speaker impedance . . . . . . . . . . . . . . 4 ohm (centre), 4 ohm (front/rear)
Speaker drivers ..... ........ ............................................................
Centre/front/rear . .. ... . .. ... . ....................................... 3” full range
Frequency response . . . . . . . . . . . . . . .......................... 150 Hz ~ 20 kHz
Dimensions (WxHxD) . .. .. ... ... ... ..................................................
Centre . . . . . . . . . . . . . . ...................................... 244 x 103 x 74 (mm)
Front/rear . . . . . . . . . . . . . . ................................. 103 x 203 x 71 (mm)
Weight .......... .............................................................................
Centre . . . . . . . . . . . . . . ............................................................ 0.85 kg
Front . .. . .. . .. ... . ............................................................... 0.58 kg
Rear . . . . . . . . . . . . . . ............................................................... 0.55 kg
Subwoofer
Impedance . . . . . . . . . . . . . . ......................................................... 4 ohm
Speaker drivers ..... ........ .......................... 165 mm (6.5”) woofer
Frequency response . . . . . . . . . . . . . . ............................40 Hz ~ 150 Hz
Dimensions (WxHxD) . .. .. ... ... ... ............... 163 x 363 x 369 (mm)
Weight .......... ................................................................... 4.7 Kg
Laser speci cation
Type . . . . . . . . . . . . . . .......................Semiconductor laser GaAIAs (CD)
Wave length . . . . . . . . . . . . . . ................................ 645 - 665 nm (DVD),
......................................................................770 - 800 nm (CD)
Output power . . . . . . . . . . . . . . ......................................... 6 mW (DVD),
.........................................................................7 mW (VCD/CD)
Beam divergence . . . . . . . . . . . . . . ...................................... 60 degrees.
Speci cations subject to change without prior notice.
1 - 4
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
CD
Use Audio Signal Disc
(replaces test disc 3)
SBC429 4822 397 30184
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Ri=50
Tuner FM
MEASUREMENT SETUP
1 - 5
Service Tools:
Universal Torx driver holder .................................4822 395 91019
Torx bit T10 150mm ...........................................4822 395 50456
Torx driver set T6-T20 .........................................4822 395 50145
Torx driver T10 extended .....................................4822 395 50423
Compact Disc:
SBC426/426A Test disc 5 + 5A ...........................4822 397 30096
SBC442 Audio Burn-in test disc 1kHz .................4822 397 30155
SBC429 Audio Signals disc .................................4822 397 30184
Dolby Pro-logic Test Disc ....................................4822 395 10216
SERVICE AIDS
HANDLING CHIP COMPONENTS
GB
A
WARNING
1 - 6
ESD
WAARSCHUWING
NL
ll ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
GB
Complete Kit ESD3 (small tablemat, wristband,
connection box, estention cable and earth cable ....... 4822 310 10671
Wristband tester ................................................................. 4822 344 13999
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
ESD PROTECTION EQUIPMENT
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
Safety components are marked by the symbol
!
.
CLASS 1
LASER PRODUCT
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
De Veiligheidsonderdelen zijn aangeduid met het symbol
!
.
3122 110 03420
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
Less composants de sécurité sont marqués
!
.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
Sicherheitsbauteile sind durch das Symbol
!
markiert.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
Componenty di sicurezza sono marcati con
!
.
GB
After servicing and before returning set to customer perform a leakage
current measurement test from all exposed metal parts to earth ground
to assure no shock hazard exist, The leakage current must not
exceed 0.5mA.
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
Varoitus !
SF
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
F
"Pour votre sécurité, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
Pb(Lead) Free Solder
When soldering , be sure to use the pb free solder.
INDENTIFICATION:
Regardless of special logo (not always indicated)
onemusttreatallsetsfrom1 Jan 2005 onwards,according
next rules:
Important note: In fact also products of year 2004 must
be treated in this way as long as you avoid mixing solderalloys (leaded/ lead-free). So best to always use SAC305
and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
• Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste
is required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste
within workshops should be avoided because paste is
not easy to store and to handle.
• Use only adequate solder tools applicable for lead-
free solder alloy. The solder tool must be able
– To reach at least a solder-temperature of 400@C,
– To stabilize the adjusted temperature at the solder-
tip
– To exchange solder-tips for different applications.
• Adjust your solder tool so that a temperature around
360@C – 380@C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400@C otherwise
wear-out of tips will rise drastically and flux-fluid will
be destroyed. To avoid wear-out of tips switch off unused equipment, or reduce heat.
• Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed solder alloy types (leaded and
lead-free).
If one cannot avoid or does not know whether product
is lead-free, clean carefully the solder-joint from old
solder alloy and re-solder with new solder alloy
(SAC305).
• Use only original spare-parts listed in the Service-
Manuals. Not listed standard-material (commodities)
has to be purchased at external companies.
• Special information for BGA-ICs:
– Always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for desoldering always use the lead-free temperature profile,
in case of doubt)
– Lead free BGA-ICs will be delivered in so-called ‘dry-
packaging’ (sealed pack including a silica gel pack) to
protect the IC against moisture. After opening,
1 - 7
dependent of MSL-level seen on indicator-label in the
bag, the BGA-IC possibly still has to be baked dry.
(MSL=Moisture Sensitivity Level). This will be
communicated via AYS-website.
Do not re-use BGAs at all.
• For sets produced before 1.1.2005 (except products
of 2004), containing leaded solder-alloy and
components, all needed spare-parts will be available
till the end of the service-period. For repair of such
sets nothing changes.
• On our website www.atyourservice.ce.Philips.com
you find more information to:
• BGA-de-/soldering (+ baking instructions)
• Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.
System , Region Code , etc. Setting Produre
2 - 12 - 1
1)System Reset
a) Press “SETUP“ button on R/C,TV will show setup menu
b) Select the menu using the and
c) Go preference page to do system reset
2)Region Code Change
a) In open mode, press”9” “9“ “9“ “9“ on R/C,then input desired
number to change region code :
1 USA
2 EU
3 AP
4 Australia ,NZ , Latam
5 Russia , INDIA
6 CHINA
3)Version Control Change
a) In open mode, press “1“ “5“ “9“ on R/C
b) Press “ok” button to con rm
c) TV will show message as below:
on R/C
7) Upgrading new software
a) Copy “software les” into a CD-R
b) Open the CD Door,then insert the CD-R program disc
c) Close the CD Door
d) VFD will show:
“Loading“
“Erase” -- erase the ash memory
“Writing” about 1 minute
“done “
* the system will switch off and on again automatically.
e) OSD will show:
upgrade le detected
Do you wish to continue with
the software upgrade?
OK Cancel
Current model HTS3375/55
Version: XX.XX.XX Release:XXXX.XX.XX
region :X Servo:XX.XX.XX.XX
8032:XX.XX.XX.XX RISC: XX.XX.XX.XX
MCU:XX.XX
If current model does not match you set use down arrow
key on the remote to change
OK
4)Password Change
a) Press “SETUP“ button on R/C,TV will show setup menu
b) Select the menu using the and on R/C
c) Go preference page select “password“ to change
* 000000 is default password supplied.
5)Check on the Software Version
a) Open the CD Door
b) Press “INFO“ button on R/C
c) TV will show the version on screen
6)Trade model
a) Press “Open/Close “ button on R/C
b) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA
OFF“
f) Select “OK”, OSD will show:
upgrade in progress...
V337X
please do not unplug or
switch off the device.
CAUTION!
This information is confi dential and may not be
distributed.Only a qualifi ed service person should
reprogram the Region Code.
REPAIR INSTRUCTIONS (ONE)
2 - 22 - 2
REPAIR INSTRUCTIONS (TWO)
2 - 32 - 3
REPAIR INSTRUCTIONS (THREE)
2 - 42 - 4
Loading...