Philips HTP5990K-93, HTP5990K User Manual

Download

www.philips.com/welcome

DVP5990K

EN DVD Video Player 6 ZH_CN DVD播放机 56

OOO O O O

XOO O O O

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363 – 2006.

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363 - 2006.

Environmental Protection Use Period

This logo refers to the period ( 10 years ) during which the toxic or hazardous substances or elements contained in electronic information products will not leak or mutate so that the use of these [substances or elements] will not result in any severe environmental pollution, any bodily injury or damage to any assets.

Battery labeling logo

Environmental Protection Use Period

This logo refers to the period ( 5 years ) during which the toxic or hazardous substances or elements contained in the battery will not leak or mutate so that the use of these [substances or elements] will not result in any severe environmental pollution, any bodily injury or damage to any assets.

LASER

Type Semiconductor laser InGaAlP (DVD) AIGaAs (CD) Wave length 658 nm (DVD) 790 nm (CD) Output Power 7.0 mW (DVD)

10.0 mW (VCD/CD) Beam divergence 60 degrees

Laser Safety

This unit employs a laser. Due to possible eye injury, only a quali ed service person should remove the cover or attempt to service this device.

NOTE: Pictures shown maybe different between countries.

CAUTION: WARNING LOCATION: ON THE BACKPLATE OF THE SET

NEVER MAKE OR CHANGE CONNECTIONS WITH THE POWER

‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.’

SWITCHED ON.

Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

通过此网站注册您的产品并获得支持：

www.philips.com/welcome

The apparatus shall not be exposed to dripping or splashing and that no objects  lled with liquids, such as vases, shall be placed on apparatus.

ATTENTION!

For Customer Use:

Read carefully the information located at the bottom or rear of your DVD Video player and enter below the Serial No. Retain this information for future reference.

Model No. DVP5990K

Serial No. _______________

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reserve engineering or disassembly is prohibited.

Language Code

Abkhazian 6566 Afar 6565 Afrikaans 6570 Amharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Avestan 6569 Aymara 6589 Azerhaijani 6590 Bahasa Melayu 7783 Bashkir 6665 Belarusian 6669 Bengali 6678 Bihari 6672 Bislama 6673 Bokmål, Norwegian 7866 Bosanski 6683 Brezhoneg 6682 Bulgarian 6671 Burmese 7789 Castellano, Español 6983 Catalán 6765 Chamorro 6772 Chechen 6769 Chewa; Chichewa; Nyanja 9072 Chuang; Zhuang 9065 Church Slavic; Slavonic 6785 Chuvash 6786 Corsican 6779 Česky 6783 Dansk 6865 Deutsch 6869 Dzongkha 6890 English 6978 Esperanto 6979 Estonian 6984 Euskara 6985  6976 Faroese 7079 Français 7082 Frysk 7089 Fijian 7074 Gaelic; Scottish Gaelic 7168 Gallegan 7176 Georgian 7565 Gikuyu; Kikuyu 7573 Guarani 7178 Gujarati 7185 Hausa 7265 Herero 7290 Hindi 7273 Hiri Motu 7279 Hrwatski 6779 Ido 7379 Interlingua (International) Interlingue 7365 Inuktitut 7385

7889

7365

Inupiaq 7375 Irish 7165 Íslenska 7383 Italiano 7384 Ivrit 7269 Japanese 7465 Javanese 7486 Kalaallisut 7576 Kannada 7578 Kashmiri 7583 Kazakh 7575 Kernewek 7587 Khmer 7577 Kinyarwanda 8287 Kirghiz 7589 Komi 7586 Korean 7579 Kuanyama; Kwanyama 7574 Kurdish 7585 Lao 7679 Latina 7665 Latvian 7686 Letzeburgesch; 7666 Limburgan; Limburger 7673 Lingala 7678 Lithuanian 7684 Luxembourgish; 7666 Macedonian 7775 Malagasy 7771 Magyar 7285 Malayalam 7776 Maltese 7784 Manx 7186 Maori 7773 Marathi 7782 Marshallese 7772 Moldavian 7779 Mongolian 7778 Nauru 7865 Navaho; Navajo 7886 Ndebele, North 7868 Ndebele, South 7882 Ndonga 7871 Nederlands 7876 Nepali 7869 Norsk 7879 Northern Sami 8369 North Ndebele 7868 Norwegian Nynorsk; 7878 Occitan; Provencal 7967 Old Bulgarian; Old Slavonic 6785 Oriya 7982 Oromo 7977 Ossetian; Ossetic 7983 Pali 8073 Panjabi 8065 Persian 7065 Polski 8076 Português 8084

Pushto 8083 Russian 8285 Quechua 8185 Raeto-Romance 8277 Romanian 8279 Rundi 8278 Samoan 8377 Sango 8371 Sanskrit 8365 Sardinian 8367 Serbian 8382 Shona 8378 Shqip 8381 Sindhi 8368 Sinhalese 8373 Slovensky 8373 Slovenian 8376 Somali 8379 Sotho; Southern 8384 South Ndebele 7882 Sundanese 8385 Suomi 7073 Swahili 8387 Swati 8383 Svenska 8386 Tagalog 8476 Tahitian 8489 Tajik 8471 Tamil 8465 Tatar 8484 Telugu 8469 Thai 8472 Tibetan 6679 Tigrinya 8473 Tonga (Tonga Islands) 8479 Tsonga 8483 Tswana 8478 Türkçe 8482 Turkmen 8475 Twi 8487 Uighur 8571 Ukrainian 8575 Urdu 8582 Uzbek 8590 Vietnamese 8673 Volapuk 8679 Walloon 8765 Welsh 6789 Wolof 8779 Xhosa 8872 Yiddish 8973 Yoruba 8979 Zulu 9085

Index

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent#: 5,451,942 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. @ 1996-2007 DTS, Inc. All Rights Reserved.

Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.

DivX, DivX Ultra Certi ed, and associated logos are trademarks of DivX, Inc. and are used under license.

English ------------------------------------------6

English

--------------------------------- 56

The USB-IF Logos are trademarks of Universal Serial Bus Implementers Forum, Inc.

HDMI and HDMI logo and High-De nition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

Table of contents

English

General

General Information ........................................................................................................ 8

Setup precautions .................................................................................................................................................8

Copyright notice ................................................................................................................................................... 8

Accessories supplied ...........................................................................................................................................8

Cleaning discs ........................................................................................................................................................8

About recycling .....................................................................................................................................................8

Product Overview

Your DVD Player ............................................................................................................... 9

Remote Control .........................................................................................................10-12

Using the remote control ................................................................................................................................12

Connections

Basic Connections .....................................................................................................13-15

Step 1: Connecting to television ..............................................................................................................13-14

Option 1: Using Composite Video jacks (CVBS) ...............................................................................13

Option 2: Using Component Video jacks (Y Pb Pr) ..........................................................................13

Option 3: Using HDMI or DVI TV jack.................................................................................................14

Step 2: Connecting the power cord ..............................................................................................................15

Optional Connections ....................................................................................................16

Connecting to an Analog Stereo System .....................................................................................................16

Connecting to a Digital AV Ampli er/Receiver .........................................................................................16

Basic Setup

Getting Started .......................................................................................................... 17-20

Finding the correct viewing channel .............................................................................................................17

Setting language preferences ..................................................................................................................... 17-18

On-screen display (OSD) language ........................................................................................................17

Audio, Subtitle and Disc Menu language for DVD playback ...........................................................18

Setting up Progressive Scan feature ..............................................................................................................19

Setting the EasyLink control .......................................................................................................................... 20

One touch control ..................................................................................................................................... 20

Disc Playback

Disc Operations .........................................................................................................21-32

Playable discs .......................................................................................................................................................21

Region codes for DVD discs ...........................................................................................................................21

Playing a disc ....................................................................................................................................................... 22

Basic playback controls .................................................................................................................................... 22

Other playback features for video discs ............................................................................................... 23-24

Using the Disc Menu ..................................................................................................................................23

Zooming.........................................................................................................................................................24

Changing sound track language ...............................................................................................................24

Changing subtitle language .......................................................................................................................24

Playback Control (VCD/SVCD) ..............................................................................................................24

Table of contents

Using Display menu options ..................................................................................................................... 25-27

Selecting title/chapter/track .................................................................................................................... 25

Searching by time ....................................................................................................................................... 25

Viewing playing time ...................................................................................................................................26

Switching camera angles ............................................................................................................................26

Preview function (VCD/SVCD/DVD) ....................................................................................................26

Selecting various repeat functions .........................................................................................................27

Repeating a speci c section (A-B) ..........................................................................................................27

Special Audio CD feature ............................................................................................................................... 28

Playing a

Playing a JPEG photo disc (slide show) ....................................................................................................... 30

Playing a MP3/ WMA/ WMV disc ..................................................................................................................31

Playing music and photo  les simultaneously .............................................................................................32

Karaoke Operation .........................................................................................................33

Playing a Karaoke disc .......................................................................................................................................33

USB Playback

USB Operation ...............................................................................................................34

Create MP3

Create MP3  les ..............................................................................................................35

Creating audio CD to MP3 format ................................................................................................................35

Setup Options

Setup Menu Options ................................................................................................. 36-47

Accessing the setup menu ................................................................................................................................36

DivX® disc ........................................................................................................................................29

Preview function ......................................................................................................................................... 30

Zooming........................................................................................................................................................ 30

Flip/Rotate picture ..................................................................................................................................... 30

Using the Karaoke Menu option .............................................................................................................33

General Setup Page ..............................................................................................................................37-38

Audio Setup Page .................................................................................................................................39-41

Video Setup Page ................................................................................................................................42-45

Preference Page ....................................................................................................................................46-47

English

Others

Software upgrade ...........................................................................................................48

Installing the latest software .......................................................................................................................... 48

Troublesho oting ........................................................................................................ 49 -52

Speci cations...................................................................................................................53

Glossary...................................................................................................................... 54-55

General Information

English

WARNING! This unit does not contain any userserviceable parts. Please leave all maintenance work to quali ed personnel.

Setup precautions

Finding a suitable location

– Place this unit on a  at, hard and stable surface. Never place the unit on a carpet. – Never place this unit on top of other equipment that might heat it up (e.g., receiver or ampli er). – Never put anything under this unit (e.g., CDs, magazines). – Install this unit near the AC outlet where the AC power plug can be easily reached.

Space for ventilation

– Place this unit in a location with adequate ventilation to prevent internal heat build up. Allow at least 10 cm (4”) clearance from the rear and the top of this unit and 5 cm (2”) from the left and right to prevent overheating.

Accessories supplied

– 1 remote control with batteries – 1 audio/video cables (yellow/white/

red)

Cleaning discs

CAUTION!

Risk of damage to discs! Never use solvents such as benzene, thinner, cleaners available commercially, or antistatic sprays intended for discs.

Wipe the disc with a micro  bre cleaning



cloth from the center to the edge in a straight line movement.

About recycling

Avoid high temperature, moisture, water and dust

– This unit must not be exposed to dripping or splashing. – Never place any object or items that can damage this unit (e.g., liquid  lled objects, lighted candles).

The making of unauthorised copies of copy-protected material, including computer programmes,  les, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offence. This unit should not be used for such purposes.

This user manual is printed on nonpolluting paper. This unit contains a large number of materials that can be recycled. If you are disposing an old equipment, please take it to a recycling center. Please observe the local regulations regarding disposal of packaging materials, exhausted batteries and old equipment.

Your DVD Player

31 2

a 1ç(Standby-On)ç

– Turns on this unit or turns off to normal

standby mode.

b Disc tray

cззззз(Open/Close)

– Opens/closes the disc tray.

d Display panel

– Shows information about the current

status of the unit.

e IR Sensor

– Point the remote control towards this

sensor.

f u (Play/Pause)

– Starts/pauses playback.

Ç(Stop)

– Stops playback.

h ç(USB) jack

– Input for USB  ash drive or digital

camera. * Not all brands and models of digital cameras are supported.

i MIC

– For microphone connection.

English

Remote Control

English

VOCAL

a 1 (Standby-On)ç

– Turns on this unit or turns off to normal

standby mode.

b çç(Open/Close)

– Opens/closes the disc tray.

c KARAOKE

– Toggles between ‘MIC’, ‘Vol’, ‘Echo’,

‘Key’ or ‘Karaoke Scoring’.

VOCAL – Choose audio channel or karaoke

method.

ZOOM

– Zoom the picture on the TV.

REPEAT A-B

– Repeat a speci c section of a disc.

d DISPLAY

– Displays the current status or disc

information.

e  

– Selects movement direction in the menu. – Press up/down for a slow backward or

forward search.

– Press left/right for fast backward or

forward search.

f SETUP

– Enters or exits the disc setup menu.

g u (Play/Pause)

– Starts or pauses playback.

Ç(Stop)

– Stops playback.

i AUDIO/CREATE MP3

– Selects an audio language or channel. – Access create MP3 menu.

j DISC MENU

– Enters or exits disc contents menu. – For VCD 2.0 and SVCD, turns on or off

the playback control mode.

k OK

– Con rms an entry or selection.

Remote Control (continued)

English

l RETURN/TITLE

– Returns to the previous menu or shows

title menu

m ./ > (Previous/Next)

– Skips to the previous or next title/

chapter/track.

– Press and hold this button for fast

backward or forward search.

n (USB)

– Switches to USB mode and shows the

content of the USB device.

o VOL +/-

– Adjusts the TV volume.

% (Mute) – Mutes or restores the volume.

CH +/– Selects the next or previous TV channel

or external input source (Video In channel, etc)

* These buttons can only be used with

Philips TVs.

VOCAL

p Numeric keypad 0-9

– Selects a track or title number of the

disc.

q SUBTITLE

– Selects a DVD subtitle language.

Remote Control (continued)

English

Using the remote control

A Open the battery compartment.

B Insert two batteries type R03 or AAA,

following the indications (+-) inside the compartment.

C Close the cover.

D Point the remote control directly at the

remote sensor (IR) on the front panel.

CAUTION! – Remove batteries if they are exhausted or if the remote control is not to be used for a long time. – Never mix batteries (old and new or carbon and alkaline, etc.). – Batteries contain chemical substances; they should be disposed of properly.

Note:

Never place any objects between the remote control and this unit while operating.

E Select the desired function (for example

u).

Basic Connections

COMPONENT

VIDEO IN

S-VIDEO

V (Pr/Cr)

U (Pb/Cb)

Video

(yellow cable)

AUDIO

VIDEO IN

Audio

(red/white cables)

Step 1: Connecting to

television

This connection enables you to view the video playback from this unit. You only need to choose one of the options below to make the video connection. – For a standard TV, follow option 1.

– For a progressive scan TV, follow

option 2.

– For a HDMI TV, follow option 3.

Option 1: Using Composite Video

You can connect this unit to a TV through the composite video cable which provides good picture quality.

Connect the audio/video cables (supplied)



from the TV OUT and AUDIO OUT L/R jacks on this unit to the video input

jack (yellow) and audio input jacks (red/ white) on your TV.

jacks (CVBS)

COMPONENT

VIDEO IN

S-VIDEO

V (Pr/Cr)

AUDIO

VIDEO IN

Audio

U (Pb/Cb)

Video

Option 2: Using Component Video

jacks (Y Pb Pr)

You can connect this unit to a TV through the component video cables which provides superior picture quality. The progressive scan video quality is only available when using Y Pb Pr connection and a progressive scan TV is required.

A Connect the component video cables

(red/blue/green - not supplied) from the Y Pb Pr jacks on this unit to the corresponding component video input jacks (or labeled as Y Pb/Cb Pr/Cr or YUV) on your TV.

B Connect the audio/video cable (red/white

- supplied) from the AUDIO OUT L/R jacks on this unit to the audio input jacks (red/white) on your TV. Leave the yellow video cable disconnected.

C Proceed to ‘Getting Started - Setting up

Progressive Scan feature’ for detailed progressive feature setup.

English

Basic Connections (continued)

English

HDTV/ DVI TV

HDMI IN

Option 3: Using HDMI or DVI TV

jack

HDMI (High De nition Multimedia Interface) is a digital interface that allows pure digital audio/video transmission without the loss of image quality.

Connect a HDMI cable (not supplied)



from the HDMI OUT jack on this unit to the HDMI input jack on a HDMIcompatible device (e.g., HDMI TV, HDCP compliant DVI TV).

Note:

– This unit is EasyLink compatible. It enables connected EasyLink compatible devices to control each other over HDMI, see ‘Setup Menu Options { Video Setup > HDMI Setup > EasyLink }’ for details. – For HDCP compliant or DVI TV, you need a HDMI-DVI adaptor cable (not supplied) to connect the DVI input jack from your TV to the HDMI OUT jack on this unit.

Helpful Hint: – The HDMI-DVI cable has only video output capability. An audio connection is required for audio output, see ‘Optional Connections’ for details.

COMPONENT

VIDEO IN

S-VIDEO

V (Pr/Cr)

AUDIO

U (Pb/Cb)

VIDEO IN

Step 2: Connecting the power cord

After everything is connected properly, plug the AC power cord into the power outlet.

Basic Connections (continued)

English

Never make or change any connections with the power turned on.

Helpful Hint: – Refer to the type plate at the rear or bottom of the product for identi cation and supply ratings.

Optional Connections

English

AUDIO

STEREO

Audio

(red/white cables)

DIGITAL

AV Receiver

AUDIO

DIGITAL

Connecting to an Analog Stereo System

You can connect this unit to a two channel stereo system (e.g. mini system, analog receiver) in order to enjoy stereo sound output.

A Connect the audio/video cables

(red/white - supplied) from the AUDIO OUT L/R jack on this unit to the audio input jacks (red/white) on your connecting device. Leave the yellow video cable disconnected.

For video connection, see ‘Basic Connections - Step 1: Connecting to television’ for details.

Helpful Hint: – See ‘Setup Menu Options - Audio Setup Page’ for optimum audio settings.

Connecting to a Digital AV Ampli er/Receiver

You can connect this unit to an AV ampli er/receiver in order to enjoy quality sound.

A Connect a coaxial cable (not supplied)

from the COAXIAL DIGITAL OUT jack on this unit to the digital coaxial input jack of the connected device.

For video connection, see ‘Basic Connections - Step 1: Connecting to television’ for details.

Helpful Hint: – You have to set the appropriate Digital Audio Output setting. Otherwise, no sound or interference may occur. See ‘Setup Menu Options - Audio Setup Page - Digital Audio Setup’ for details.

Getting Started

Finding the correct viewing channel

A Press 2 to turn on this unit.

B Turn on the TV and switch it to the

correct video-in channel. You should see the blue DVD background screen.

 You may go to the lowest channel on

your TV, then press the Channel Down button on your TV’s remote control until you see the Video In channel.

 You may press

on your TV’s remote control.

 Usually this channel is between the

lowest and highest channels and may be called FRONT, A/V IN, VIDEO, etc.



Refer to your TV user manual on how

to select the correct input on your TV.

C If you are using external device, (such as

audio system or receiver), turn it on and select the appropriate input source for this unit output. Refer to the device user manual for detail.

button repeatedly

Setting language preferences

The language options are different depending on your country or region. It may not correspond to the illustrations shown on the user manual.

On-screen display (OSD) language

Select this to change the language of the On screen display menu of this unit. The menu language will remain once you have set it.

A Press SETUP on the remote control.

 { General Setup Page } appears.

B Use  keys to select { OSD

Language } in the menu and press .

General Setup Page

Disc Lock

OSD Language Auto (CHI)

Sleep ENGLISH

Lip Sync

Volume

Auto Standby

DivX(R) VOD Code

English

C Use  keys to select a language and

press OK to con rm.

Note:

– To synchronize with a Philips ‘EasyLink’ TV, the OSD language must be set to { Auto (xxx) }. This is the language available from the Philips ‘EasyLink’ TV. – If a non-supported language is selected, the default OSD language of this unit will be used.

Getting Started (continu ed)

English

Audio, Subtitle and Disc Menu language for DVD playback

You can select your preferred language settings for DVD playback. If the selected language is not available on the disc, the disc’s default language is used instead.

A Press

twice to stop playback (if any),



then press SETUP.

B Press  repeatedly to select

{ Preference Page }.

C Use  keys to select one of the

options below and press .

Preference Page

Audio English

Subtitle Chinese

Disc Menu French

Parental Spanish

PBC

Mp3/Jpeg Nav Polish

Password Italian

{ Audio } Select this to change disc sound track language.

Portuguese

D Use  keys to select a language and

press OK to con rm.

If the language you want is not in

the list, then select { Others }, then use the numeric keypad 0-9 on the remote control to enter the 4-digit language code ‘XXXX’ (see ‘Language Code’) and press OK.

E Repeat steps C - D for other language

settings.

{ Subtitle } Select this to change the subtitle language.

{ Disc Menu } Select this to change the language of the disc menu.

Getting Started (continu ed)

Setting up Progressive Scan feature

(for Progressive Scan TV only)

The progressive scan displays twice the number of frames per second than interlaced scanning (ordinary normal TV system). With nearly double the number of lines, progressive scan offers higher picture resolution and quality.

Before you start...

– Ensure that you have connected this unit to a progressive scan TV (see ‘Option 2: Using Component Video jacks (Y Pb Pr)’ ).

A Turn on the TV to the correct viewing

channel for this unit.

 Make sure that the TV progressive

scan mode is turned off (or set to interlaced mode). Refer to your TV user manual.

B Turn on this unit and press SETUP on

the remote control.

C Press  repeatedly to select { Video

Setup Page }.

D Use  keys to select { Progressive }

> { On } in the menu and press OK to con rm.

Video Setup Page

TV Type

TV Display

Progressive

Picture Setting

HD JPEG

HDMI Setup

Off

E Read the noti cation message on the TV

and con rm your action by selecting the { OK }

in the menu and press OK.

There will be no picture on your TV at this state until you have turned on the progressive scan mode on your TV.

F Turn on your TV progressive scan mode,

refer to your TVs user manual.

 A message appears on the TV.

G Con rm your action by selecting the

{ OK }

in the menu and press OK.

 The setup is now completed and you

can start to enjoy the high quality picture.

If no picture is displayed

A Press ç to open the disc tray.

B Press numeric keypad ‘1’ on the

remote control.

 The unit background screen appears.

Helpful Hints: – If a blank/distorted screen appears, wait for 15 seconds for the auto recovery. – Some progressive scan TVs are not fully compatible with this unit, resulting in an unnatural picture when playing back a DVD VIDEO disc in the progressive scan mode. In such a case, turn off the progressive scan feature on this unit and your TV.

English

Getting Started (continu ed)

English

Setting the EasyLink control

This feature enables HDMI CEC compliant devices to control each other with a single remote control. It is only available if you have connected this unit to HDMI CEC compliant TV or device with HDMI cable.

A Turn on the HDMI CEC operations on

your TV and other connected devices. (Refer to your TV or connected devices manual for details.)

B Press SETUP on the remote control.

C Press  repeatedly to select { Video

Setup Page }.

D Use  keys to select { HDMI Setup }

> { EasyLink } and press  to access.

EasyLink

Auto Wake Up TV

System Standby

The functions are turned on by default in



the factory.

– To disable { Auto Wake Up TV }

feature, select { Off }.

– To disable { System Standby }

feature, select { Decline }.

E To exit, press SETUP.

One touch control

Notes:

– To enable one touch play function, a video disc must be placed in the disc compartment before operation. – Philips does not guarantee 100% interoperability with all HDMI CEC compliant devices.

One touch play

Press 2.



 It turns on this unit and start disc play.  Your TV automatically turns on and

switches to the correct video channel.

One touch input switching

While this unit and TV are turned on;

Select a TV channel to watch TV



programme or start play on other connected device.

 This unit automatically switches to the

corresponding audio input and output the sound from its speakers system.

One touch power off

Press STANDBY/POWER button to turn



off this unit and all the HDMI CEC compliant devices.

 When using this unit’s remote control,

you have to press and hold 2.

Disc Operations

Playable discs

This unit plays:

– Digital Versatile Discs (DVDs) – Video CDs (VCDs) – Super Video CDs (SVCDs) – Finalized DVD Recordable (DVD±R), DVD Rewritable (DVD±RW) – Audio Compact Discs (CDs) – MP3/ WMA discs

– The  le extension has to be ‘.mp3’,

‘.wma’ – JPEG/ISO format – Maximum 14 characters display. – Supported bit-rate; 32 – 320 kbps (MP3) 64 – 192 kbps (WMA)

– WMV  les on CD-R(W)/ DVD+R(W)

– The  le extension has to be ‘.wmv’.

– Picture  les (Kodak, JPEG) on CD-R(W)/DVD+R(W)

– The  le extension has to be ‘.JPG’

and not ‘.JPEG.’ – JPEG/ISO format – It can only display DCF-standard

still pictures or JPEG pictures such

as TIFF.

– DivX®  les on CD-R(W)/ DVD+R(W) – The  le extensions has to be ‘.AVI’,

‘.MPG’ or ‘.MP4’.

– DivX®

Certi ed

– Q-pel accurate motion

compensation

– Global Motion Compensation

(GMC) playback

Certi ed, DivX® Ultra

Region codes for DVD discs

DVD discs and players are designed with regional restrictions. Before playing a disc, make sure the disc is for the same region as your unit. The region code for this unit is indicated at the rear panel.

Region

U.S.A. and Canada regions

U.K and Europe regions

Asia Paci c, Taiwan, Korea

Australia, New Zealand, Latin America

Russia and India regions

China, Calcos Islands, Walls and Futuna Islands

Helpful Hints: – Maximum 10 sessions for CD and 10 multi border for DVD are supported. – For DVD-R and DVD-RW multi border, only  nalized discs are supported.

Discs that can

be played

English

Disc Operations (continued)

English

Notes: – If the inhibit icon the TV when a button is pressed, it means the function is not available on the current disc or at the current time. – Never put any objects other than discs in the disc tray. Doing so may cause this unit to malfunction.

appears on

Playing a disc

A Press 2 to turn on this unit.

B Turn on the TV to the correct viewing

channel for this unit.

C Press çto open the disc tray.

D Load a disc into the disc tray and press

ç.

 Make sure the disc label is facing

towards you.

E Playback starts automatically.

 If not, press u .  See the following pages for more

playback options and features.

Helpful Hints: – Never close the disc tray manually. – If you are having trouble playing a certain disc, remove the disc and try a different one. Improperly formatted discs cannot be played on this unit. – Some discs cannot be played on this unit due to the con guration and characteristics of the disc, or due to the condition of recording and authoring software that was used.

Basic playback controls

Pausing playback

 During playback, press u.

 To resume playback, press u.

Selecting another track/chapter/ title

Press ./ > or use the



numeric keypad 0-9 to enter a track/ chapter/title number.

 If the repeat track mode is active,

press . again to replay the same track/chapter/title.

Searching backward/forward (not applicable for JPEG)

Press m / M.



 While searching, press m / M

repeatedly to select different search speed (2X, 4X, 8X, 16X, 32X).

 To resume normal playback, press

Playing in slow motion mode (not applicable for CD/WMA/MP3/ JPEG)

During playback, press /  to start



slow motion play.

 Sound will be muted. Press / 

repeatedly to select different play speed (1/2, 1/4, 1/8, 1/16).

Note: Slow backward motion playback is only possible for DVD.

 To resume normal playback, press

Stopping playback

Press x.



Disc Operations (continued)

Helpful Hints: – For video disc, playback always resumes from the point where it was last stopped. To start playback from the beginning, press . while the message ‘Play from the start, press [PREV]’ is displayed. – Screen saver starts automatically if playback is stopped or paused for about 5 minutes.

Other playback features for video discs

ZOOM

DISC MENU

RETURN/

TITLE

SUBTITLE

Note:

The operating features described here might not be possible for certain discs. Always refer to the instructions supplied with the discs.

AUDIO/

CREATE MP3

English

Using the Disc Menu

Depending on the disc, a menu may appear on the TV once you load in the disc.

To select a playback feature Use   keys or numeric keypad



0-9 on the remote control, then press OK to start playback.

To access or exit the menu

Press DISC MENU on the remote



control.

Disc Operations (continued)

English

Zooming

This option allows you to zoom and pan through the picture on the TV.

A During playback, press ZOOM

repeatedly to select a different zoom factor.

 Playback continues.

B Use   keys to pan through the

enlarged picture.

C Press ZOOM repeatedly to return to

the original size.

Changing sound track language

This operation works only on DVDs with multiple sound track languages, or VCDs/ SVCDs with multiple audio channels.

For DVD

Press AUDIO/CREATE MP3



repeatedly to select the available audio languages.

For VCD/SVCD

Press AUDIO/CREATE MP3



repeatedly to select the available audio channels provided by the disc.

Playback Control (VCD/SVCD)

Playback Control (PBC) playback allows you to play Video CDs or SVCDs interactively, following the menu on the display.

For VCDs with PBC feature (version 2.0 only) and SVCDs

Press DISC MENU to turn on or off



the PBC mode.

 If the PBC mode is turned on, the

PBC menu (if available) appears on the TV.

 If the PBC mode is turned off, it skips

the PBC menu and playback from the  rst track.

If the PBC mode is turned on, pressing



RETURN/TITLE during playback will return to the PBC menu.

Helpful Hint: – You cannot use numeric keypad 0-9 to select track if PBC mode is on.

Changing subtitle language

This operation works only on DVDs with multiple subtitle languages. You can change to your desired language during playback.

Press SUBTITLE repeatedly to select



different subtitle languages.

Disc Operations (continued)

Using Display menu options

This unit can display the disc playback information (for example, title or chapter number, elapsed playing time), a number of operations can be done without interrupting disc playback.

A During playback, press DISPLAY on the

remote control.

 The available disc information appears

on the TV.

Title 01/01

Chapter 01/01

Audio 5.1CH Others

Subtitle Off

Bitrate 61 Title Elapsed 0:48:59

(VCD/SVCD)

Track 01/21

Disc Time 1:12:32

Track Time 0:02:29

Repeat ab Off

Bitrate 61 Total Elapsed 0:48:59

DISPLAY

(DVD)

B Use  keys to view the information

and press OK to access.

C Use the numeric keypad 0-9 to input

the number/time or use  keys to make the selection.

D Press OK to con rm.

 Playback changes to the selected

operation.

Selecting title/chapter/track

This option allows you to skip to a speci c title/chapter/track in the current disc.

A Move to { Title } / { Chapter } or { Track }

option in the display menu and press .

B Use the numeric keypad 0-9 to input

the valid number.

 Playback skips to the selected

operation.

Searching by time

This option allows you to skip to a speci c point in the current disc.

A Move to { TT Time / CH Time / Disc

Time / Track Time } in the display menu and press .

B Use the numeric keypad 0-9 to enter

the time where playback should start (eg. 0:34:27).

 Playback skips to the selected time.

English

Disc Operations (continued)

English

Viewing playing time

It shows the remaining/elapsed time display of the current disc.

A Move to { Time Disp } in the display

menu and press .

 The information and display are differ

depending on the disc type.

For DVD

Display Descriptions

Title/Chapter Elapsed

Title/Chapter Remain

For VCD/SVCD

Display Descriptions

Total/Single Elapsed

Total/Single Remain

Switching camera angles

. This option is only available on DVDs

that contain sequences recorded from different camera angles. This allows you to view the picture from different angles.

Title or Chapter elapsed playing time.

Title or Chapter remaining playing time.

Disc or Track elapsed playing time.

Disc or Track remaining playing time.

Preview function (VCD/SVCD/DVD)

This function allows you to preview the contents of a VCD/SVCD/DVD disc.

A Move to { Preview } in the display menu

and press .

 The preview menu appears.

(DVD)

Select Digest Type:

Title Digest

Chapter Digest

Title Interval

Chapter Interval

(VCD/SVCD)

Select Digest Type:

Track Digest

Disc Interval

Track Interval

B Use  keys to select one of the

preview type and press OK.

 Thumbnail pictures of each segment

appear on the TV.

02 03

ABC

DEF

A Move to { Angle } in the display menu and

press .

B Use the numeric keypad 0-9 to input a

valid number.

 Playback changes to the selected

angle.

To go to the previous or next page, press



./ >.

C Use   keys to select a thumbnail

picture and press OK to start playback from there.

Disc Operations (continued)

Selecting various repeat functions

This function allows you to select the different repeat play options.

For DVD/VCD/SVCD

A Move to { Repeat } in the display menu

and press .

DVD

 Chapter (repeat current chapter)  Title (repeat current title)  All (repeat entire disc)  Off (exit repeat mode)

VCD/SVCD

 Track (repeat current track)  All (repeat entire disc)  Off (exit repeat mode)

For Audio CD

A Press DISPLAY repeatedly to select

{ Off }, then press / to select the following repeat mode.

 Track (repeat current track)  All (repeat entire disc)  Off (exit repeat mode)

Repeating a speci c section (A-B)

A Move to { Repeat ab } in the display

menu.

B Press OK at the start point.

C Press OK again to end the section.

 The section will now repeat

continuously.

D Press OK again to resume normal

playback.

Helpful Hints: – The marked section for repeat playback is only possible within the same chapter/track. – While in disc playback mode, you can also use REPEAT A-B on the remote control to repeat a speci c section.

English

For MP3/WMA/WMV/JPEG/DivX®

A In stop mode, press DISPLAY

repeatedly to select the following repeat mode.

 Single (repeat current  le once)  Repeat One (repeat current  le)  Repeat Folder (repeat all  les in the

current folder)  Folder (repeat all  les in a folder)

Helpful Hint: – Repeat playback is not possible on VCDs or SVCDs when the PBC mode is turned on.

Disc Operations (continued)

English

Special Audio CD feature

This is a time search option for audio CD playback. Playback skips to the time you input, within the disc or track.

A During playback, press DISPLAY

repeatedly to toggle between different input options.

Display Descriptions

Disc Go To Time search within the

Track Go To Time search within a

Select Track Select a track number.

B Use the numeric keypad 0-9 to enter

the time where playback should start (minutes:seconds).

 Playback skips to the selected time.

disc.

track.

Playing a DivX® disc

This unit supports the playback of DivX movie which you can copy from your computer onto a recordable disc. See ‘Setup Menu Options - { General Setup Page > DivX(R) VOD Code }’ for details.

A Load a DivX disc.

B Use  keys to select to the  le you

want to play.

C Press OK to start playback.

During playback;

If the DivX disc has multilingual subtitles,



you can press SUBTITLE on the remote control to change the subtitle language.

If the DivX disc has different audio



tracks, you can press AUDIO/CREATE MP3 on the remote control to change

the audio stream.

Disc Operations (continued)

Advance features of the DivX

Features Descriptions

XSUB™ subtitles

Interactive video menus

Alternate audio tracks

Chapter points

– allow multiple language

subtitles selection for movie.

– provide easy access and

control.

– quick navigation to

various scenes/features and select audio/subtitle options.

– enable audio tracks

in multiple language versions.

– separate audio tracks

for speci c speaker con gurations.

– provide  exibility. – allow jump straight to the

scene you want to watch from any point in video.

Ultra

English

Helpful Hints: – Subtitle  les with the following  le name extensions (.srt, .smi, .sub, .ssa, .txt) are supported but do not appear on the  le navigation menu. – The subtitle  le name (.sub) has to be saved under the same  le name as the movie (.avi) in the same folder.

Disc Operations (continued)

English

Playing a JPEG photo disc (slide show)

Before you start ...

Turn on your TV to the correct Video In channel. See ‘Finding the correct viewing channel’ for details.

Load a photo CD (Kodak Picture CD/



JPEG).

 The picture menu appears on the TV.  For Kodak disc, the slide show begins

automatically. Press u to start the slide-show playback.

During playback:

Press u to pause or resume playback.



Press ./ > to play another  le in



the folder.

Helpful Hints: – It may require longer time to display the disc content due to the large number of songs/pictures compiled into one disc.

Supported  le format:

– The  le extension has to be ‘*.JPG’ and not ‘*.JPEG’. – This unit can only display digital camera pictures according to the JPEG-EXIF format, typically used by almost all digital cameras. It cannot display Motion JPEG, or pictures in formats other than JPEG, or sound clips associated with pictures.

Preview function

A During playback, press DISPLAY.

 12 thumbnail pictures will be displayed

on the TV.

B Press ./ > to display pictures on

the previous/next page.

C Use   keys to select one of the

pictures and press OK to start playback.

D Press DISC MENU to return to Picture

CD menu.

Zooming

A During playback, press ZOOM

repeatedly to select a magni cation level.

B Use   keys to pan through the

enlarged image.

Flip/Rotate picture

During playback, use   keys to



rotate/ ip the picture on the TV.

Action Remote

control

 ip the picture vertically.

 ip the picture horizontally.

rotate the picture counterclockwise.

rotate the picture clockwise.









Disc Operations (continued)

Playing a MP3/ WMA/ WMV disc

This unit can playback most of the MP3 and WMA/WMV  les recorded on a recordable disc or commercial CD.

Before you start ...

Turn on your TV to the correct Video In channel. See ‘Finding the correct viewing channel’ for details.

A Load a MP3/WMA/WMV disc.

 The disc reading time may exceed 30

seconds due to the complexity of the directory/ le con guration.

 The disc menu appears on the TV.

01:42 04:40 128kbps 001/020

\MP3

MP3 Music 1

MP3

MP3 Music 2

MP3

Picture 1

B Use  keys to select a desired folder

and press OK to open the folder.

C Use  keys to select a  le and press

OK to start playback.

 Playback starts from the selected  le

and continues through to the end of the folder.

During playback:

Press ./ > to playback another  le



in the current folder.

Press m / M repeatedly to fast



backward/ forward search on the  le.

To select another folder from current



disc, use  keys to navigate back to the root menu.

D To stop playback, press x.

Helpful Hints: – The unit can only support WMV 9 Main Pro le (Low Level) with  le extension ‘wmv’. It does not support playback of Advanced Pro le and DRM-protected video  les. – You can set to display or skip the folders when you load a MP3/JPEG disc. Press SETUP, then go to { Preference Page > Mp3/Jpeg NAV }. – Only the  rst session of a multi-session CD will be played back. – It is normal to experience an occasional ‘skip’ while listening to your MP3/WMA disc due to poor clarity of digital contents during internet downloading. – If any special characters are present in the MP3/WMA track name (ID3) or album name, it might not be displayed correctly on the screen because this unit does not support the characters. – The ID3/Meta information will not display when the playback  le is not selected.

English

Disc Operations (continued)

English

Playing music and photo  les simultaneously

You can create a musical slide show playback if the disc contains both the MP3/WMA music and JPEG picture  les.

A Load a disc that contains both MP3/WMA

and JPEG  les.

B Use  keys to select a MP3/WMA  le

from the disc menu and press OK to start playback.

C During MP3/WMA playback, use 

keys to select a JPEG  le from the disc menu and press OK.

 Slideshow begins and continues till the

end of the photo folder or album.

D To stop simultaneous playback, press x

twice.

Helpful Hints: – Some  les on Kodak or JPEG disc may be distorted during playback due to the con guration and characteristics of the disc. – During simultaneous playback, fast forward / backward or slow forward/ backward is not available.

Karaoke Operation

Playing a Karaoke disc

Before you start...

Turn on your TV to the correct Video In channel. Press AV, VIDEO, SELECT or

button on your TV’s remote control

until you see the blue DVD background.

A Connect a microphone (not supplied) to

the MIC jack on the front panel of this unit.

B Load a karaoke disc.

If the disc menu appears, use  



keys to make your selection and press OK to start playback.

C Press KARAOKE on the remote

control repeatedly to select { MIC ON/ OFF }.

 Use   keys to turn the microphone

{ ON } or { OFF }.

D Press KARAOKE on the remote

control repeatedly to select { Vol }.

 Use   keys to adjust the

microphone volume.

Using the Karaoke Menu option

A Press KARAOKE on the remote

control repeatedly to access the karaoke menu.

{ MIC } – Use   keys to turn the microphone { ON } or { OFF }.

{ Vol } – Use   keys to adjust the microphone volume between 0 ~ 20.

{ Echo } – Use   keys to adjust the echo level between 0 ~ 20.

{ Key } – Use   keys to adjust the pitch level between -16 ~ +16 that match your voice.

{ Karaoke Scoring } – Use   keys to select scoring ranks: { Off } , { Basic } , { Intermediate } or { Advance }. Note: If you score 30 points and above at the end of the song, a karaoke score will appear on the TV. Press OK to exit the scoring and resume karaoke session.

Helpful Hint: – Karaoke score function is only available for DVD and VCD discs.

English

E Press VOCAL repeatedly to toggle

between various audio modes.

 You can turn off the vocal or change

the audio mode of the karaoke disc.

 Start enjoying the karaoke.

Helpful Hint: – Before connecting the microphone, set the microphone volume to the minumum level to prevent howling.

USB Operation

English

You can play or view the data  les (JPEG, MP3, WMA, WMV or DivX®) in the USB  ash drive. However, editing or copying the data  le is not possible.

A Connect the USB  ash drive directly to

the

jack on this unit.

B A message appears on the TV when the

device is detected.

C Press on the remote control to

access the data in the drive.

D Use  keys to select a desired  le and

press OK to start playback.

For more playback information, see



‘Playing a DivX® disc’, ‘Playing a JPEG photo disc (slide show)’ or ‘Playing a MP3/WMA/WMV disc’ for details.

E Press x to stop playback.

F Press on the remote control to

exit from the menu and switch to disc mode.

 You can remove the USB device now.

Helpful Hints: – The USB jack does not support the connection of other USB devices except to a USB  ash drive. – The unit can only support up to a maximum of 300 folders and 648  les. – When the USB device does not  t into the USB jack, a USB extension cable (not supplied) is required. – Copy-protected  les are not playable.

Create MP3  les

Creating audio CD to MP3 format

This feature allows you to convert audio tracks from an audio CD into MP3 format. The created MP3  les are saved in your USB device.

A Connect the USB  ash drive directly to

the

B Load an audio CD.

C During playback, press AUDIO/

CREATE MP3 on the remote control.

D Read the message on the TV and con rm

your action by selecting { YES } in the menu, then press OK.

 The Create MP3 menu appears.  If the USB device is full, a warning

message will be displayed.

E De ne your requirements for creating

MP3  les in the { OPTIONS } menu, then press OK.

jack on this unit.

Create MP3

OPTIONS

Speed Normal

Bitrate 128kbps

CRT ID3 Yes

Device USB 1

SUMMARY

Selected 0

Total Time 00:00

Start Exit

TRACK

Track01 04:14

Track02 04:17

Track03 03:58

Track04 04:51

Track05 03:53

Track06 04:09

Track07 04:38

Select all

Deselect all

{ CRT ID3 } Create ID3 information.

{ Yes } ID3 information is

included in the MP3  le.

{ No } No ID3 information.

{ Device } The created MP3  les will save in this USB device.

F Move to the { TRACK } menu and use

 keys to select the track that you want to create, then press OK.

To select all tracks, move to



{ Select all } in the menu and press OK.

To deselect all tracks, move to



{ Deselect all } in the menu and press OK.

G To start creating the tracks, move to

{ Start } in the menu and press OK.

 The creating process menu appears.  If the USB device is full, a warning

message will be displayed.

 A new folder is created automatically

in the USB device to store all the new MP3  les.

Note: If you press one of the buttons on the front panel or remote control (1, ç, x, AUDIO/CREATE MP3 or OK) during creating process, a message ‘Do you want to stop Creating MP3 now?’ appears on the TV screen. Select { Cancel } to continue creating process.

English

{ Speed } Select the creating speed.

{ Normal } Normal speed.

Note: You are able to hear the playback while creating the audio tracks.

{ Fast } Fast speed.

{ Bitrate } Select a creating bitrate. Default setting is 128 kbps.

H To exit the menu, move to { Exit } in the

menu and press OK.

Helpful Hints: – DTS CD and copy-protected CD cannot be created to MP3 format. – Write protected or password protected USB device cannot be used to store the MP3  les.

Setup Menu Options

English

Accessing the setup menu

You can change the settings in this unit to suit your particular requirements.

SETUP

A Press SETUP on the remote control.

 The setup menu appears.

B Use   keys to select one of the setup

menu.

If you are not able to access the



{ Preference Page }, press SETUP to exit the menu. Then, press x twice before you press the SETUP again.

C Use  keys to select a setup option

and press  to access.

D Select your desired setting and press OK

to con rm.

 Instructions and explanations of the

options are provided in the following pages.

 If the option in the menu is grayed

out, that means the setting is not available or cannot be changed in the current state.

E To exit, press SETUP.

General Setup Page

Disc Lock

OSD Language

Sleep

Lip Sync

Volume

Auto Standby

DivX(R) VOD Code

See ‘General Setup Page’ on this chapter.

Audio Setup Page

Analog Output

Digital Audio Setup

HDMI Audio

Sound Mode

CD Upsampling

Night Mode

See ‘Audio Setup Page’ on this chapter.

Video Setup Page

TV Type

TV Display

Progressive

Picture Setting

HD JPEG

HDMI Setup

See ‘Video Setup Page’ on this chapter.

Preference Page

Audio

Subtitle

Disc Menu

Parental

PBC

Mp3/Jpeg Nav

Password

See ‘Preference Page’ on this chapter.

Setup Menu Options (continued)

General Setup Page

Disc Lock

OSD Language

Sleep

Lip Sync

(underlined options are the factory default settings)

Not all discs are rated or coded by the disc maker. You can prevent play of speci c discs with the disc lock function. Up to 20 discs can be locked.

{ Lock } – To block the playback of the current

disc. Subsequent access to a locked disc requires a six-digit password. The default password is ‘136900’ (see { Preference Page - Password }).

{ Unlock } – All discs can be played.

Select the menu language for this unit’s on-screen display.

The sleep timer enables this unit to switch to standby mode automatically after the selected a preset time.

{ 15/30/45/60 Mins } – Select the preset minutes for

switching this unit to standby mode automatically.

{ Off } – Turn off the sleep mode.

This feature allows you to adjust the audio delay times if the video playback is slower than the audio output streams, hence resulting in lip-sync.

Access the lip sync setup menu. Use   keys to set the delay times (00 ~ 200 ms) for the audio output and press OK to exit.

English

Setup Menu Options (continued)

English

General Setup Page

(underlined options are the factory default settings)

Volume

Auto Standby

DivX(R) VOD Code

This setting allows you to adjust the volume level.

Access the volume setup menu. Use   keys to set the volume level between 00 ~ 20 and press OK to exit.

Select this to switch this unit to standby mode when it is not in use for a period of time.

{ On } – Switched to low power standby mode

when playback has paused or stopped for more than 15 minutes.

{ Off } – Switch off the auto standby mode.

Philips provides you with the DivX® VOD (Video On Demand) registration code that allows you to rent or purchase videos from DivX® VOD service at http://www.divx.com/vod. All the downloaded videos from DivX® VOD can only be played back on this unit.

Press  to see the registration code and press OK to exit.

Setup Menu Options (continued)

Audio Setup Page (underlined options are the factory default settings)

Analog Output

Digital Audio Setup

his setting is only required if you have connected the audio output of this unit to a stereo device or TV using the analog output jack.

{ LT/RT } – The connected device has a built-in

Dolby Pro Logic decoder. It can deliver the surround sound through the two speakers.

{ Stereo } – The connected device can only output

stereo audio through two speakers.

{ V SURR } – For virtual surround sound effects.

This setting is only required if you have connected the audio output of this unit to an ampli er/receiver using the digital output jack.

{ Digital Output } – { Off

{ All } The connected device supports multi-

{ PCM Only } The connected device does not support

}

Disable digital audio output. Select this if you are using the analog audio jacks to connect this unit to a TV or Stereo system.

channel audio formats. The digital audio format will be output as on disc.

multi-channel formats. All audio signals are downmixed to PCM format (2-channel).

English

Setup Menu Options (continued)

English

Audio Setup Page (underlined options are the factory default settings)

Digital Audio Setup

HDMI Audio

Continued...

{ LPCM Output } – { 48 K }

Select this to play disc recorded at sampling rate of 48 kHz.

{ 96 K } Enable 96 kHz output on digital audio if

the ampli er/receiver is compatible with high sampling rate audio (88.2 / 96 kHz). However, if the sound output is distorted or there is no sound, change the setting to ‘48 K’.

Notes: – Digital Audio Setup setting is only available if HDMI Audio

Setup is set to { Off }. – LPCM Output can only be selected when { PCM Only } is

activated. The higher the sampling rate, the better the sound quality.

This setting is only required if you are using the HDMI OUT jack to connect your TV or other display device.

{ On } – Enable audio output through HDMI

connection.

{ Off } – Disable HDMI audio output. In this

case, an alternative audio connection is required from this unit to your TV.

Sound Mode

Select the type of preset digital sound effect that can match the disc’s content or optimize the sound of the musical style you are playing.

{ 3D } – It provides a virtual surround sound

experience through the left and right audio channels. Available options are: { Off }, { Living Room }, { Hall }, { Arena } and { Church }.

{ Movie Mode } – Movie sound effects. Available options

are: { Off }, { Sci-Fi }, { Action }, { Drama } and { Concert } effect.

{ Music Mode } – Musical sound effects. Available options

are: { Off }, { Digital }, { Rock }, { Classic } and { Jazz }.

Setup Menu Options (continued)

Audio Setup Page (underlined options are the factory default settings)

CD Upsampling

Night Mode

This feature enables you to convert the music CD to a higher sampling rate using sophisticated digital signal processing for better sound quality. If you have activated the CD upsampling, this unit automatically switches to stereo mode.

{ Off } – Disable CD-upsampling function. { 88.2 kHz (X2) } – Convert the sampling rate of the CDs

to twice as high as the original rate.

{ 176.4 kHz (X4) } – Convert the sampling rate of the CDs

to four times as high as the original rate.

Note: CD upsampling is only possible when playback the music CD in stereo mode.

This mode optimizes playback of sound at low volume. High volume outputs will be softened and low volume outputs will be enhanced to an audible level. This feature is only applicable for DVD video discs with Dolby Digital mode.

{ On } – Turn on night mode. { Off } – Turn off night mode. Select this to

enjoy the surround sound with its full dynamic range.

English

Setup Menu Options (continued)

English

Video Setup Page (underlined options are the factory default settings)

TV Type

TV Display

Progressive

Select the color system that matches the connected TV. It enables playback of a different type of disc (PAL or NTSC disc) on this unit.

{ PAL } – For PAL-system TV. { Multi } – For TV that is compatible with both

PAL and NTSC.

{ NTSC } – For NTSC-system TV.

The picture shape can be adjusted to  t your TV.

{ 4:3 Pan Scan } – For a full-height picture

with the sides trimmed.

{ 4:3 Letter Box } – For a ‘wide-screen’ display

with black bars on the top and bottom.

{ 16:9 } – For wide-screen TV

(frame ratio 16:9).

Before enabling the progressive scan feature, you must ensure that your TV can accept progressive signals (a progressive scan TV is required) and that you have connected this unit to your TV using the Y Pb Pr. See ‘Getting Started - Setting up Progressive Scan feature’ for details.

{ On } – Turn on progressive scan mode. Read the instructions on the TV and

con rm your action by pressing OK on the remote control.

{ Off } – Turn off progressive scan mode.

Note: The Progressive Scan setting will not be available when the HDMI video signal is detected.

Setup Menu Options (continued)

Video Setup Page (underlined options are the factory default settings)

Picture Setting

Personal Picture Setup

Brightness 0

Contrast 0

Sharpness 0

Color 0

HD JPEG

This unit provides three prede ned sets of picture color settings and one personal setting which you can de ne yourself.

{ Standard } – Original color setting. { Vivid } – Vibrant color setting. { Cool } – Soft color setting. { Personal } – Select this to personalize the picture

color setting. Use the   keys to adjust to the setting that best suits your personal preference and press OK to con rm. For an average setting, select { 0 }.

HD JPEG allows you to enjoy untouched and uncompressed pictures at it’s original resolution. This feature is only applicable if you have connected this unit to a HDMI-compatible TV/device.

{ On } – Display high de nition picture. { Off } – Display standard picture.

Note: This feature is only available for JPEG picture disc. This unit supports the display resolution of 720p and above.

English

Setup Menu Options (continued)

English

Video Setup Page (underlined options are the factory default settings)

HDMI Setup

It provides the picture settings to enhance the appearance and picture quality for disc playback. This feature is only applicable if you have connected this unit to a HDMI-compatible TV/device.

{ Resolution } – Select a suitable video resolution that is

compatible with your TV display capability.

{ Auto } It detects and selects the best

supported video resolution automatically.

{ 480p, 576p, 720p, 1080i, 1080p } Manually select a video resolution. ‘p’

for progressive and ‘i’ for interlaced.

Note: – If the selected resolution is not supported by your HDMI/DVI

TV, a black screen will appear. In this case, wait for 5 seconds for auto recovery or use the composite (yellow) video cable to connect this unit and your TV. Turn on your TV to the correct input channel for the composite video and adjust the resolution setting to 480p/576p.

{ Wide Screen Format } – Select a suitable screen display

{ 4:3 Pillar Box } Display the 4:3 picture disc on the wide-

screen TV without stretching. Black bars will be shown on the both sides of the TV.

{ Super Wide }

Display the 4:3 picture disc on the wide-screen TV with non-linear stretching (center position of the screen is stretched less than the side).

{ Off } No aspect ratio adjustment is made

when this option is selected.

Note: { Super Wide } and

{ 4:3 Pillar Box } is only applicable when this unit’s resolution is set to 720p, 1080i or 1080p.

Setup Menu Options (continued)

Video Setup Page (underlined options are the factory default settings)

HDMI Setup

Continued...

{ EasyLink } – Enable HDMI CEC compliant TV/

devices to control each other with a single remote control.

Notes: – Your TV and other connected devices must be compliant with

HDMI CEC. – You must turn on the HDMI CEC operations on your TV/

devices before you can enjoy the EasyLink controls. See your TVs/devices manual for details.

– Philips does not guarantee 100% interoperability with all HDMI CEC compliant devices.

{ Auto Wake Up TV } Press STANDBY button to turn on

(both your TV and this unit) and start video disc play (if a video disc is found in the disc tray). Your TV automatically switches to the correct video channel.

To disable this feature, select { Off }.

{ System Standby } Press STANDBY/POWER button to

turn off this unit and all the HDMI CEC compliant devices.

To disable this feature, select { Decline }.

English

Note: However, press and hold 2

Note: If a noti cation message appears, con rm your setting by

selecting { OK } in the menu and press OK to proceed.

button on this unit remote control can still turn off all the HDMI CEC compliant devices.

Setup Menu Options (continued)

English

Preference Page (underlined options are the factory default settings)

Audio

Subtitle

Disc Menu

Parental

Select the preferred audio language for DVDs with multiple sound tracks.

Select the preferred subtitle language for DVDs playback.

Select the preferred disc menu language for DVDs playback.

Note: If the selected audio/subtitle/disc menu language is not available on the DVDs, the disc’s default language will be used instead.

This setting allows you to control the playback of certain disc through a rating level. It works only on the DVDs with parental level assigned to the complete disc or to certain scenes on the disc.

1) Use  keys to select a rating level from 1 to 8 and press

OK.

2) Use the numeric keypad 0-9 on the remote control to enter your six-digit password and press OK.

Notes: – The ratings are country-dependent (‘1’ is considered material

that is least offensive and ‘8’ is most offensive). To disable parental controls and allow all discs to play, select ‘8’.

– Some DVDs are not encoded with a rating though the movie

rating may be printed on the disc cover. The rating level feature does not prohibit playback of such discs. VCD, SVCD and CD have no level indication, so parental control has no effect on these type of discs.

– DVDs that are rated higher than the level you selected will

not be played unless you enter the same six-digit password.

PBC

Play Back Control feature is applicable for VCD/SVCD only. It allows you to play Video CDs (2.0) interactively, following the menu on the display.

{ On } – The index menu (if available) appears

on the TV when you load a VCD/ SVCD.

{ Off } – The VCD/SVCD skips the index menu

and playback directly from the beginning.

Setup Menu Options (continued)

Preference Page (underlined options are the factory default settings)

Mp3/Jpeg Nav

Password

Mp3/Jpeg Navigator can only be set if the disc is recorded with a menu. It allows you to select different display menus for easy navigation.

{ Without Menu } – Display all the  les contained in the

MP3/Picture disc.

{ With Menu } – Display the folder menu of the MP3/

Picture disc.

Note: This feature is not available for USB mode.

Select this to set the password for Parental control and Disc Lock. The default password is ‘136900’.

To change the password:

1) Press OK twice to access the change password menu.

Old Password

New Password

Confirm PWD

2) Use the numeric keypad 0-9 on the remote control to

enter your existing six-digit password at { Old Password }.

Note: When doing this for the  rst time or if you forget your existing password, enter ‘136900’.

3) Enter the new six-digit password at { New Password }.

4) Enter the new six-digit password again at { Con rm PWD }.

5) Press OK to con rm and exit.

English

DivX Subtitle

Default

Select the font type that supports the recorded DivX subtitle. {

} (Simpli ed Chinese)

– Display a standard list of simpli ed

Chinese subtitle fonts provided by this unit.

This setting enables you to reset all the options and settings to the factory defaults, with exception of your password for Parental control and Disc Lock.

Press OK to con rm the default reset.

Software upgrade

English

Installing the latest software

Philips provides software upgrades to make sure that this unit is compatible with the newest formats. To check the updates, compare the current software version of this unit with the latest software version available at the Philips website.

A Press çto open the disc tray.

B Press numeric keypad ‘55’ on the

remote control.

C Write down the  le name.

D Go to www.philips.com/support to check

the latest software version available for this unit.

E If the latest software version is higher

than the software version of this unit, download it and store onto a CD-R.

F Load the CD-R to this unit for upgrade

operation.

Note: Never unplug or turn off this unit during the upgrade.

G Once complete, this unit will restart

automatically.

Troubl es hoo ti ng

WARNING

Under no circumstances should you try to repair this unit yourself, as this invalidates the warranty. Do not open this unit as there is a risk of electric shock.

If a fault occurs,  rst check the points listed below before taking this unit for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help.

Problem Solution

English

No power.

No picture.

Completely distorted picture or black/white picture.

No sound or distorted sound.

– Press 1 on the unit to turn on the power. – Ensure that the AC outlet has power. – Disconnect the power cord from the power outlet.

Reconnect and try again after a few minutes.

– Refer to your TVs manual for correct Video In

channel selection. Change the TV channel until you see the DVD screen.

– If this happens when you turn on the progressive scan

feature, wait for 15 seconds for the auto recovery or switch back to the default mode as below:

1) Press ç to open the disc tray.

2) Press numeric keypad ‘1’ on the remote control.

– If this happens after you set the color system, wait for

15 seconds for the auto recovery or switch back to the default TV color system:

1) Press ç to open the disc tray.

2) Press numeric keypad ‘3’ on the remote control.

– Check the video connection. – Ensure that the disc is compatible with this unit. – Sometimes a small amount of picture distortion may

appear. This is not a malfunction.

– The disc is dirty. Clean the disc.

– Check the audio connections to the connected audio

device.

– Make sure that the connected audio device is turned

on to the correct input source.

– Set the digital output setting correctly, based on the

device you connected to this unit. See ‘Audio Setup Page – Digital Audio Setup’ for details.

Troubl es hoo ti ng (continued)

English

Problem Solution

The remote control does not function properly.

The unit does not start playback.

The buttons on the unit do not work.

The aspect ratio of the screen cannot be changed even though you have set the TV display.

– Aim the remote control directly at the sensor on the

front of this unit (not towards the TV).

– Remove any obstacles between this unit and the

remote control. – Batteries are weak, replace the batteries. – Check the polarities of the batteries are as indicated

on the remote control (± signs).

– Load a readable disc with the playback side facing

inwards. The DVD±R/DVD-RW/CD-R must be

 nalized. – Make sure the disc is not scratched or warped. Check

if the disc is defective by trying another disc. – The disc is of a different region code. – You may need to enter the password in order to

unlock the disc for playback. – Moisture may have condensed inside this unit.

Remove the disc and leave this unit turned on for

about an hour.

– There is a technical problem. Disconnect this unit

from the power outlet for 10 seconds and reconnect

again.

– The aspect ratio is  xed on the DVD disc. – Depending on the TV, it may not be possible to

change the aspect ratio.

Cannot activate some features such as Angles, Subtitles, or multi-language

Audio.

Not able to select some items in the setup/system menu.

– The features may not be available on the DVD. – Changing the language for the sound or subtitle is

prohibited on this DVD.

– Press x twice before selecting the disc setup menu. – Depending on the disc availability, some menu items

cannot be selected.

Troubl es hoo ti ng (continued)

Problem Solution

Picture freezes momentarily during playback.

Unable to select Progressive Scan on/off.

No audio output from HDMI connection.

No video output from HDMI connection.

– Check the disc for  ngerprint/scratches and clean

with a soft cloth wiping from center to edge.

– Check that the video output of this unit is connected

using the Component Video (Y Pb Pr) jacks. – Remove the HDMI connection.

– You will not hear any sound from the HDMI output if

the source device is only DVI/HDCP (High-bandwidth

Digital Content Protection)-compatible. – It is not possible to output or copy-controlled DVD-

Audio sources from the HDMI connection. – Make sure that the audio output setting is not turned

off. See ‘Setup Menu Options - { Audio Setup Page -

HDMI Audio }’ for details.

– HDMI connection can only be made to HDMI-

equipped devices with HDCP (High Bandwidth Digital

Content Protection). If you wish to connect to a DVI

connector (equipped with HDCP), you need a

separate adaptor (DVI to HDMI). – Make sure the resolution of this unit matches the

device you have connected using the HDMI. See

‘Setup Menu Options - { Video Setup Page - HDMI

Setup }’ for details. – During resolution selection for DVI TV, a distorted or

black screen may appear, see HDMI Setup.

English

No sound during DivX movies playback.

An DivX movie does not repeat.

– The audio codec may not be supported by this unit.

– Check that  le size of the movie does not exceed the

 le size of the disc during downloading.

Troubl es hoo ti ng (continued)

English

Problem Solution

Certain DivX files do not play or are skipped.

The contents of the USB  ash drive cannot be read.

Slow operation of the USB  ash drive.

– Check that the DivX movie download is a complete

 le. – Make sure the  le name extension is correct. You can

check this using a computer with CD-ROM. – The unit is designed to playback DVD, VCD, SVCD,

CD audio, MP3, WMA, WMV and DivX discs only.

Other digital audio formats such as liquid audio, RM

(RealMedia), WAV or non-audio  les like ‘.doc’, ‘.txt’,

‘.pdf’ are not supported. – Try to play the problem DivX files on a computer. If

they do not work, the source file appears to be

corrupted. – Try to download the file again from a different source,

or if you have created the file yourself, save it with

the correct settings.

– The USB  ash drive format is not compatible with the

system. – Drive is formatted with a different  le system which is

not supported by this unit (e.g., NTFS).

– Large  le size or high memory USB  ash drive takes

longer time to read and display on the TV.

Speci cations

TV STANDARD

(PAL/50Hz) (NTSC/60Hz) Number of lines 625 525 Playback Multistandard (PAL/NTSC)

VIDEO PERFORMANCE

Video DAC 12 bit, 108 MHz Y Pb Pr 0.7 Vpp ~ 75 ohm Video Output 1 Vpp ~ 75 ohm

VIDEO FORMAT

Digital MPEG 2 for DVD, SVCD Compression MPEG 1 for VCD

DVD 50 Hz 60 Hz

Horiz. resolution 720 pixels 720 pixels 1920 pixels 1920 pixels Vertical resolution 576 lines 480 lines 1080 lines 1080 lines

VCD 50 Hz 60 Hz

Horiz. resolution 352 pixels 352 pixels Vertical resolution 288 lines 240 lines

AUDIO FORMAT

Digital MPEG/ AC-3/ compressed PCM Digital 16, 20, 24 bits fs, 44.1, 48, 96 kHz MP3 (ISO 9660) 96, 112, 128, 256 kbps & variable bit rate fs, 32, 44.1, 48 kHz

Analog Sound Stereo Dolby Surround compatible downmix from Dolby Digital multi-channel sound

DivX®

AUDIO PERFORMANCE

DA Converter 24 bit, 192 kHz DVD fs 96 kHz 4 Hz - 44 kHz fs 48 kHz 4 Hz - 22 kHz SVCD fs 48 kHz 4 Hz - 22 kHz fs 44.1kHz 4 Hz - 20 kHz CD/VCD fs 44.1kHz 4 Hz - 20 kHz

Signal-Noise (1kHz) > 90 dB Dynamic range(1kHz) > 80 dB Crosstalk (1kHz) > 70 dB Distortion/noise (1kHz) > 65 dB MPEG MP3 MPEG Audio L3

CONNECTIONS

Y Pb Pr Output Cinch 3x Video Output Cinch (yellow) Audio Output(L+R) Cinch (red/white) Digital Output 1 coaxial IEC60958 for CDDA / LPCM IEC61937 for MPEG 1/2, Dolby Digital HDMI Output

CABINET

Dimensions (w x h x d) 435 x 38 x 209 mm Weight Approximately 2 kg

POWER CONSUMPTION

Power Supply Rating 110 V - 240 V; 50/60 Hz Power consumption < 12 W Power consumption in < 1 W Standby mode

Speci cations are subject to change without prior notice.

English

Glossary

English

Analog audio: Sound that has not been turned into numbers. Analog sound is available when you use the AUDIO LEFT/ RIGHT jacks. These red and white jacks send audio through two channels, the left and right.

Aspect ratio: Aspect ratio refers to the length to height ratio of TV. The ratio of a standard TV is 4:3, while the ratio of a highde nition or wide TV is 16:9. The letter box allows you to enjoy a picture with a wider perspective on a standard 4:3 screen.

AUDIO OUT jacks: Red and white jacks on the back of this unit that send audio to another system (TV, Stereo, etc.).

Bit Rate: The amount of data used to hold a given length of music; measured in kilobits per second, or kbps. Or, the speed at which you record. Generally, the higher the bit rate, or the higher the recording speed, the better the sound quality. However, higher bit rates use more space on a disc.

Dolby Digital: A surround sound system developed by Dolby Laboratories containing up to six channels of digital audio (front left and right, surround left and right, center and subwoofer).

EasyLink: Philips EasyLink uses the HDMI CEC industry standard protocol to share functionalities between the unit and its connected devices. This feature is only available if you connect this unit to a HDMI CEC compliant TV with a HDMI cable.

HDMI: High-De nition Multimedia Interface (HDMI) is a high-speed digital interface that can transmit uncompressed high de nition video and digital multichannel audio. It delivers perfect picture and sound quality, completely free from noise. HDMI is fully backward-compatible with DVI. As required by the HDMI standard, connecting to HDMI or DVI products without HDCP (High-bandwidth Digital Content Protection) result in no Video or Audio output.

Chapter: Sections of a picture or a music piece on a DVD that are smaller than titles. A title is composed of several chapters. Each chapter is assigned a chapter number enabling you to locate the chapter you want.

Composite video (CVBS): A single video signal commonly used in most consumer video products.

Disc Menu: A screen display prepared for allowing a selection of images, sounds, subtitles, multi-angles, etc., recorded on a DVD.

DivX: The DivX code is a patent-pending, MPEG-4 based video compression technology, developed by DivX Networks, Inc., that can shrink digital video to sizes small enough to be transported over the internet, while maintaining high visual quality.

HDCP (High-bandwidth Digital Content Protection) is a speci cation that provides a secure transmission of digital contents between different devices (to prevent unauthorized copyright).

JPEG: A very common digital still picture format. A still-picture data compression system proposed by the Joint Photographic Expert Group, which features small decrease in image quality in spite of its high compression ratio. Files are recognized by their  le extension ‘JPG or JPEG’.

Glossary (contin ued)

MP3: A  le format with a sound data

compression system. ‘MP3’ is the abbreviation of Motion Picture Experts Group 1 (or MPEG-1) Audio Layer3. By using the MP3 format, one CD-R or CD-RW can contain about 10 times more data than a regular CD.

Parental Control: A function of the DVD to limit playback of the disc by the age of the users according to the limitation level in each country. The limitation varies from disc to disc; when it is activated, playback will be prohibited if the software’s level is higher than the user-set level.

PBC: Playback Control. A system of navigating a Video CD/Super VCD through on-screen menus recorded onto the disc. You can enjoy interactive playback and searching.

PCM (Pulse Code Modulation): A system for converting analog sound signal to digital signal for later processing, with no data compression used in conversion.

Progressive Scan: The progressive scan displays twice the number of frames per second than in an ordinary TV system. It offers higher picture resolution and quality.

Title: The longest section of a movie or music feature on DVD. Each title is assigned a title number, enabling you to locate the title you want.

TV OUT jack: Jack on the back of this unit that sends out video signals to the TV.

WMA: Windows Media™ Audio. Refers to an audio compression technology developed by Microsoft Corporation. WMA data can be encoded by using Windows Media Player version 9 or Windows Media Player for Windows XP. Files are recognized by their  le extension ‘WMA’.

WMV: A video  le or stream in Windows Media format. It is a compression format of motion picture based on MPEG-4 developed by Microsoft.

English

Region code: A system allowing discs to be played only in the region designated. This unit will only play discs that have compatible region codes. You can  nd the region code of your unit by looking at the product label. Some discs are compatible with more than one region (or ALL regions).

Philips HTP5990K-93, HTP5990K User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual