Philips HR8571AC Service Manual

Mobilo Vacuum cleaner

HR8571
/A
/C

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Blue purple
/C : Christal white

- Maximum air displacement : 32 l/sec.

- Maximum vacuum water column : 240 cm

- Power consumption (IEC) : 1200 W

- Duststorage capacity : 3 litres

- Cord length (depends on version) : 6 metres

- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter

- Dimensions cleaner : 445 x 295 x 250 mm

- Weight cleaner : 5.5 kg

OPTIONAL (accessories)

Exhaust air filter HR6932 = 4822 015 70056
Hard floor nozzle HR6943 = 4822 479 20222
Active carbon filter HR6949 = 8838 033 01010
Active carbon filter replacem. set HR6968 = item 12 + 13
S-class filter HR6992 = 8838 044 01010
S-class filter replacement set HR6994 = item 19 + 20
Sydney cotton dustbag HR6997 = 4822 480 10115
Sydney closable paper dustbag FC8021 = 8838 021 00000
Turbo brush FC8043 = 4322 004 22960

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

03/10

HR8571 /A /C

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- To open the appliance, first remove the 2 screws of the

control panel (item 11) then with a big screw driver
disconnect the 2 snap locks of panel and lower housing
(see drawing).

- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.

- When the repair is finished, check whether all functions of
the appliance work properly.

- To (dis)assemble the appliance use TORX screw driver no
T15 (4822 395 10329), which is one of a set consisting of
T20, T15, TI0, T9, T8, T7 and T6 = 4822 395 50145.

- To connect the nozzle, the telescopic tube and the handle:
insert the narrowed section into the wider section while
turning it a little.
To disconnect: Pull while rotating. To adjust the telescopic
tube (item 74) to the required length, use the knob in the
direction of the arrow while sliding the top section of the
telescopic tube into or out of the lower section.

REPAIR INSTRUCTION

- The spare parts have been standardized as much as possible.

- Item 6, cotton dustbag, is used in those countries where

paper dustbags are not available.

- The cordwinder (item 21) is provided with a long cord-

winder spring; both long and short cords can be used in
combination with this spring.

- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn.

- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.

- If the cord comes without AMP clamps, it can be soldered
onto the terminals.

- If the reel half spring unit is replaced, shaft A must be
lubricated with silicone grease (A). Do not apply any
silicone grease to or spill any grease on the terminals or
conductors.

- The assembly of accessories depends on the national
version.

- Adjusting the PCB on the motor to 220V, 60Hz.

1. Make sure that the potentiometer (item 36) is set at

min. position.

2. Adjust the potentiometer on the PCB item 45, on the

motor to 220V/60Hz to allow the motor to run
smoothly.

Please note: the standard setting of the spare PCB is

230V/50Hz.
There are open-circuit voltages on all wires.

M

MOTOR
POWER

MODULE

MAIN

SWITCH

CORD WINDER

ROTARY
POTMETER

2-6