Philips HR8568AD Service Manual

Mobilo Vacuum cleaner

HR8568
/A
/B
/C
/D

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A /B /C : Plum red
/D : Black granite

- Maximum air displacement : 32 l/sec.

- Maximum vacuum water column : 240 cm

- Power consumption (IEC) : 1200 W

- Duststorage capacity : 3 litres

- Cord length (depends on version) : 6 metres

- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter

- Dimensions cleaner : 445 x 295 x 250 mm

- Weight cleaner : 5.5 kg

OPTIONAL (accessories)

Exhaust air filter HR6932 = 4822 015 70056
Hard floor nozzle HR6943 = 4822 479 20222
Active carbon filter HR6949 = 8838 033 01010
Active carbon filter replacem. set HR6968 = item 12 + 13
Turbo brush HR6988 = 4322 004 22960
S-class filter HR6992 = 8838 044 01010
S-class filter replacement set HR6994 = item 19 + 20
Sydney cotton dustbag HR6997 = 4822 480 10115
Sydney closable paper dustbag HR6999 = 4822 480 10113

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

03/10

HR8568 /A /B /C /D

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- To open the appliance, first remove the 2 screws of the

control panel (item 11) then with a big screw driver
disconnect the 2 snap locks of panel and lower housing
(see drawing).

- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.

- When the repair is finished, check whether all functions of
the appliance work properly.

- To (dis)assemble the appliance use TORX screw driver no
T15 (4822 395 10329), which is one of a set consisting of
T20, T15, TI0, T9, T8, T7 and T6 = 4822 395 50145.

- To connect the nozzle, the telescopic tube and the handle:
insert the narrowed section into the wider section while
turning it a little.
To disconnect: Pull while rotating. To adjust the telescopic
tube (item 74) to the required length, use the knob in the
direction of the arrow while sliding the top section of the
telescopic tube into or out of the lower section.

REPAIR INSTRUCTION

- The spare parts have been standardized as much as possible.

- Item 6, cotton dustbag, is used in those countries where

paper dustbags are not available.

- The cordwinder is provided with a long cord-winder spring;
both long and short cords can be used in combination with
this spring.

- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn.

- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.

- If the cord comes without AMP clamps, it can be soldered
onto the terminals.

- If the reel half spring unit is replaced, shaft A must be
lubricated with silicone grease (A). Do not apply any
silicone grease to or spill any grease on the terminals or
conductors.

- The assembly of accessories depends on the national
version.

- Adjusting the PCB on the motor to 220V, 60Hz.

1. Make sure that the potentiometer (item 36) is set at

min. position.

2. Adjust the potentiometer on the PCB item 45, on the

motor to 220V/60Hz to allow the motor to run
smoothly.

Please note: the standard setting of the spare PCB is

230V/50Hz.
There are open-circuit voltages on all wires.

M

MOTOR
POWER

MODULE

MAIN

SWITCH

CORD WINDER

ROTARY
POTMETER

2-7

PARTS LIST

HR8568 /A /B /C /D

Pos Service code Description Version

1

4822 442 01824
4322 003 23260

2

4822 492 11408

3

4822 441 12336
4322 009 09110

4

4822 532 60926

5

4822 441 12334
4322 003 23290

6

4822 480 10113
4822 480 10115

7

4822 256 10354

8

4822 401 11689

9

4822 466 11497

10

4822 410 12453
4322 005 16690

11

4822 441 12335
4322 003 23280

12

4822 458 10649
4822 458 10461

13

4822 480 10228

4822 480 20145

14

4822 410 12454
4322 003 23310

15

4822 466 62655

16

4822 466 11487

17

4822 462 11178

18

4822 441 12341

19

4822 015 70056
8838 044 01010

20

4822 458 10682

4322 005 15970

21

4822 492 71489

23

4822 532 52554

24

4822 528 10836

25

4822 290 81474

26

4822 321 10816

27

4822 321 10822

28

4822 321 10818

29

4822 321 10783

30

4822 321 10806

Acc. cover Plum red /A/B/C
Acc. cover Black granite /D
Dust indicator spring
Dust panel Plum red /A/B/C
Dust panel Black granite /D

Packing ring
Front cover Plum red /A/B/C
Front cover Black granite /D
Sydney closable pap. dustbag
Sydney cotton dustbag

Dustbag carrier
Clamp of dustbag carrier
Dust compartment sealing
Turn knob Plum red /A/B/C
Turn knob Black granite /D

Back panel Plum red /A/B/C
Back panel Black granite /D
Inletgrill + trio fi lter
Active carbon fi lter grill (opt.)
Trio fi lter

Active carbon fi lter (opt.)
Pedal Plum red /A/B/C
Pedal Black granite /D
Bufferring motor
Motor disc

Cord out let
Lower housing + wheels
Exhaust air fi lter
S-fi lter
Air outlet grill

S-fi lter grill
Reel half spring unit /A
Brake tyre /A
Reel half contact unit /A
Contact ring plate /A

Cord set Australia /A
Cord set Japan/low voltage /A
Cord set UK /A
Cord set 4.8 mm pins /A
Cord set Swiss /A

Pos Service code Description Version

31

4822 321 10815

32

4822 532 12782

33

4822 528 11334

34

4822 462 11179

35

4822 528 11335

36

4822 214 12224

37

4822 479 20197

41

4822 276 13205

42

4822 462 10911

43

4822 466 10765

44

4822 402 10109

45

4822 214 11359

46

4822 492 11011

47

4822 361 10768

48

4822 492 11407

71

4822 492 71622

72

4822 530 10229

73

4822 492 71623

74

4822 530 10233

75

4822 530 10382

76

4822 530 10235

77

4822 479 20195

78

4822 479 60118

79

4822 479 70072

80

4822 479 20123

81

4822 479 30176

82

4322 009 07940

83

4322 001 72360

84

4322 009 07950

85

4322 009 07960

86

4322 006 01440
4322 006 01760

87

4322 006 01680

88

4322 006 01720

89

4322 006 01410

90

4322 006 01670

91

4322 006 01460

92

4322 004 22860

A

5322 390 20011

B

4322 002 82550

Cord set Italy /A
Dustbag sealing
Caster
Cover
Rearwheel (standard)

Speed control 220-240V
Cord winder lever
Push button switch
Motor cover
Rear motor buffer

Suspension bracket
Motor power PCB 230V-50Hz
PCB clamp
Motor 220-240V/50-60Hz
Spring switch-knob

Clip metal tube (opt.)
Metal tube (opt.)
Clip telescopic tube
Telescopic tube
Bend + hose ass’y

Bend ass’y
Crevice nozzle
Small nozzle
Big nozzle
Strip of big nozzle

Plumeau
Reel half spring unit (L=9m) /B/C/D
Brake tyre /B/C/D
Reel half contact unit /B/C/D
Contact ring plate /B/C/D

Argentina L=9.3 m /B/C/D
Australia L=9.3 m /B/C/D
Taiwan L=6.3 m /B/C/D
U.K. / H.K. L=9.3 m /B/C/D
Euro 4.8mm pins L=9.3 m /B/C/D

Swiss L=9.3 m /B/C/D
Italy L=9.3 m /B/C/D
Hardfl oor nozzle

Silicon grease for the shaft
Screw 3.5 x 12 / T10

3-7