Philips HR2020 User Manual [es]

HR2020

2

3

1

4

ENGLISH 6
ESPAÑOL 11

繁體中文 16

HR2020

6

ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the support that

Philips offers, register your product at www.philips.com/welcome.

Important

Read this user manual carefully before you use the appliance and save it for future reference.
Noise level: Lc = 86 dB(A)

General
Danger

Never immerse the motor unit in water or any other liquid, nor rinse it under the tap. Use only

­a moist cloth to clean the motor unit.

Warning

Check if the voltage indicated on the appliance corresponds to the local mains voltage before

­you connect the appliance.
If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by

-

Philips or similarly qualied persons in order to avoid a hazard.

Do not use the appliance if the plug, the mains cord or other parts are damaged.

­Never use the blender jar to switch the appliance on and off.

­Never let the appliance run unattended.

­This appliance is not intended for use by persons (including children) with reduced physical,

­sensory or metal capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not play with the appliance.

­Do not touch the blades, especially when the appliance is plugged in. The blades are very sharp.

­If the blades get stuck, unplug the appliance before you remove the ingredients that block the

­blades.
Never place the blade unit onto the motor unit if the blender jar is not or not properly

­attached to it.

Caution

Always unplug the appliance before you assemble, disassemble or make adjustments to any of

­the parts.
Never use any accessories or parts from other manufacturers or that Philips does

-

not specically recommend. If you use such accessories or parts, your guarantee becomes

invalid.

Blender
Warning

Never reach into the blender jar with your ngers or an object while the appliance is running.

­Make sure the blade unit is securely fastened to the blender jar before you assemble the

­blender jar onto the motor unit.

Caution

Never ll the blender jar with ingredients hotter than 80ºC.

­To prevent spillage, do not put more than 1.5 litres of liquid in the blender jar, especially when

­you process at a high speed. Do not put more than 1 litre in the blender jar when you process
hot liquids or ingredients that tend to foam.
To prevent overloading the motor, do not put more than 0.75 litres in the blender jar when you

­process thick ingredients.

ENGLISH 7

If food sticks to the wall of the blender jar, switch off the appliance and unplug it. Then use a

­spatula to remove the food from the wall.
Always make sure the lid is properly assembled on the jar and the measuring cup is inserted

­properly in the lid before you switch on the appliance.
Never forget to place the sealing ring on the blade unit before you connect the blade unit to

­the blender jar, otherwise leakage will occur.
Do not let the appliance run for more than 3 minutes at a time.

­Always let the appliance cool down to room temperature between processing cycles.

-

Electromagnetic elds (EMF)

This Philips appliance complies with all standards regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this user manual, the appliance is safe to use based on

scientic evidence available today.

Built-in safety lock

This feature ensures that you can only switch on the appliance if you have properly assembled the
blender jar on the motor unit. If the blender jar is correctly assembled, the built-in safety lock will be
unlocked.

General description (Fig. 1)

A Measuring cup
B Lid of blender jar
C Blender jar
D Level indication
E Sealing ring

F Blade unit

G Motor unit
H Control panel

Speed buttons (1 and 2)

­Pulse/off button

-

Before rst use

Thoroughly clean the parts that come into contact with food before you use the appliance for the

rst time (see chapter ‘Cleaning’).

Using the appliance

You can adjust the length of the cord by winding par t of it round the reel in the base. Pass the cord
through the slot in the base.

Blender

The blender is intended for ne pureeing, chopping and blending. With the blender you can prepare

soups, sauces and milk shakes. You can also use it to process vegetables, fruit, meat, pancake batter
etc.

Preparing the blender for use

1 Assemble the sealing ring on the blender blade unit (Fig. 2).

2 Put the blade unit in the bottom of the blender jar (1). Screw the blade unit anticlockwise (2)

until it is xed properly (Fig. 3).

3 Put the blender jar with the blade unit attached on the motor unit and x it by turning it

clockwise (‘click’) (Fig. 4).

ENGLISH8

The blender jar can be mounted in two positions: with the handle on the right side or on the left
side.

4 Put the mains plug in the wall socket.

Using the blender

1 Put the ingredients in the blender jar.

2 Put the lid on the jar and turn it until it is rmly xed (‘click’).

3 Insert the measuring cup into the opening in the lid (Fig. 5).

4 Press speed button 1 or 2 to switch on the blender.

After processing, press the pulse/off button to switch off the blender. If you want to process

ingredients very briey, use the pulse/off button instead of the speed buttons.

Do not let the appliance run for more than 3 minutes at a time. Let it cool down to room
temperature between processing cycles.

Tips

If you want to crush ice cubes, put not more than 4 ice cubes (of approx. 25x35x25mm) in the

­blender jar and press the pulse button a few times.
Cut meat or other solid ingredients into smaller pieces before you put them in the blender jar.

­Do not process a large quantity of solid ingredients at the same time. To get good results, we

­advise you to process these ingredients in a series of small batches.
To make tomato juice, cut the tomatoes in four and drop the pieces through the opening in the

­lid onto the rotating blades.

Disassembling the blender

1 Remove the mains plug from the wall socket.

2 Remove the lid with the measuring cup from the blender jar.

3 Turn the blender jar with the blade unit attached anticlockwise to remove it from the motor

unit.

4 Clean all removable parts immediately after use (see chapter ‘Cleaning’).

Cleaning

Always unplug the appliance before you clean it.

Never immerse the motor unit in water, nor rinse it under the tap. Do not clean the motor unit

in the dishwasher.

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone
to clean the appliance.

Tip: Cleaning the appliance and its parts is easiest immediately after use.

1 Make sure the appliance is unplugged.

2 Disassemble all removable parts.

Do not forget to remove the blender sealing ring.

Do not touch the blades. The blades are very sharp.

3 Clean the motor unit with a moist cloth.

4 Clean the removable parts in hot water with some washing-up liquid.

Note: All parts except the motor unit can be cleaned in the dishwasher.