Philips HQT788/00, HQT788/70, HQT788 Instructions For Use Manual
HQT788
2
ENGLISH 4
FRANÇAIS 13
PORTUGUÊS 23
á«Hô©dG 41
v<ñUã 50
HQT788
Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗ The appliance is equipped with an automatic
voltage selector and is suitable for mains
voltages ranging from 100 to 240 volts.
◗ Only use the appliance in combination with
the mains cord supplied.
◗ If the mains cord is damaged, always have it
replaced by one of the original type in order
to avoid a hazard.
◗ Make sure the appliance and the cord do not
get wet.
◗ Keep the appliance out of the reach of
children.
◗ Use, charge and store the appliance at a
temperature between 15cC and 35cC.
◗ This appliance is only designed for trimming
the human beard. Do not use the appliance
for any other purpose.
◗ Do not use the appliance if the cutting unit is
damaged or broken, as this may cause injury.
Before first use
◗ Charge the appliance fully before using it for
the first time (see chapter 'Charging').
◗ When the appliance has been charged for the
first time, we advise you to use it until the
battery is completely empty.
ENGLISH4
Charging
C
1 Make sure the appliance is switched off.
C
2 Insert the appliance plug into the
appliance.
3 Put the mains plug in the wall socket.
C
◗ The charging light goes on to indicate that the
appliance is charging.
It will take approx. 1 hour to fully charge the
battery. The charging light blinks to indicate that
the battery has been fully charged.
Do not charge the appliance for more than
24 hours.
When it is fully charged, the appliance has a
cordless trimming time of up to 40 minutes.
Optimising the lifetime of the rechargeable
battery
- Do not recharge the appliance in between the
trimming sessions.
- Discharge the battery completely twice a year
by letting the motor run until it stops.
- Do not keep the appliance plugged into a wall
socket all the time.
ENGLISH 5
CHARGE
Using the appliance
Always comb your beard or moustache with a
fine comb before you start trimming.
If you are trimming for the first time, be careful
Do not move the trimmer too fast. Make smooth
and gentle movements.
Corded trimming
◗ To use the trimmer connected to the mains:
switch the trimmer off, connect it to the
mains and wait a few seconds before
switching it on.
If the battery is completely empty, wait one
minute before switching the appliance on, as the
trimmer might not start working right away.
Do not run the appliance from the mains when
the battery is fully charged.
Trimming with comb attachment
C
1 Turn the Precision Zoom Lock` to the
desired hair length setting (see table).
The setting will appear in the window below the
Precision Zoom Lock`.
ENGLISH6
9
9
Hair length setting table
B
If you are trimming for the first time, start by using
the maximum hair length setting (9).
2 Switch the appliance on.
C
3 Place the trimmer on the skin and move
the trimmer slowly over the skin against
the direction of hair growth while pressing
it lightly.
Make sure the surface of the comb attachment
always stays in contact with the skin.
◗ If a lot of hair has accumulated in the comb
attachment:
4 Remove the comb attachment by pulling it
off the appliance.
ENGLISH 7
Resulting hair length
1.5mm
2.5mm
4.0mm
5.5mm
7.5mm
9.5mm
12.0mm
15.0mm
18.0mm
Hair length setting
1
2
3
4
5
6
7
8
9
Never pull at the flexible top of the comb
attachment. Always pull at the bottom part.
C
5 Blow or shake the hair out of the comb
attachment.
The selected hair length setting will not change
when you do this.
Trimming at the unique 'stubble look'
setting
C
◗ Using the trimmer with the comb attachment
set to setting 1 allows you to create a 'stubble
look'.
Trimming without comb attachment
Use the trimmer without comb attachment to
trim full beards and single hairs.
C
1 Remove the comb attachment by pulling it
off the appliance.
Never pull at the flexible top of the comb
attachment. Always pull at the bottom part.
2 Switch the appliance on.
C
3 Make well-controlled movements. Touch
the hair lightly with the trimmer.
ENGLISH8
Trimming with the precision trimmer
You can use the precision trimmer to shape your
moustache and sideburns, to define contours and
to cut single hairs.
1 Remove the comb attachment.
C
2 Push the precision trimmer upwards. If the
appliance is switched on, the precision
trimmer will start to work right away.
Note: the main cutting unit continues to work
when you use the pop-up precision trimmer.
C
3 Hold the appliance in vertical position and
make strokes.
The pop-up precision trimmer is also suitable for
outlining the edges of the beard on the throat
and on the cheeks.
C
4 When you have finished using the pop-up
precision trimmer, push it back into the
appliance.
You can now put the comb attachment back
onto the appliance.
Cleaning
Do not use abrasives, scourers or liquids such as
alcohol, petrol or acetone to clean the appliance.
1 Make sure the appliance is switched off
and disconnected from the mains before
you start cleaning it.
ENGLISH 9
2 Remove the comb attachment.
C
3 Flip the cutting unit open.
C
4 Clean the cutting unit and the hair
chamber with the brush supplied.
C
5 Close the cutting unit by pushing it back
onto the appliance ('click').
The appliance does not need any lubrication.
Replacement
A worn or damaged cutting unit must always be
replaced with an original Philips cutting unit,
available from authorised Philips service centres.
1 Flip the cutting unit open.
C
2 Remove the old cutting unit by pulling it
upwards.
C
3 Place the two lugs of the new cutting unit
into the guiding slots.
4 Push the cutting unit onto the appliance
('click').
ENGLISH10
Environment
C
◗ Do not throw the appliance away with the
normal household waste at the end of its life,
but hand it in at an official collection point for
recycling. By doing this you will help to
preserve the environment.
◗ The built-in rechargeable battery contains
substances that may pollute the environment.
Always remove the battery before discarding
the appliance and handing it in at an official
collection point. Dispose of the battery at an
official collection point for batteries. If you
have trouble removing the battery, you can
also take the appliance to a Philips service
centre, which will remove the battery for you
and will dispose of it in an environmentally
safe way.
Disposal of the battery
1 Disconnect the appliance from the mains
and let the appliance run until the motor
stops.
C
2 Undo the screw in the trimmer housing.
C
3 Separate the 2 housing parts by means of a
screwdriver.
ENGLISH 11
C
4 Insert a screwdriver into the small slots in
the printed circuit board marked with an
arrow. Push the screwdriver down until
parts of the printed circuit board break
off.
C
5 Press the hook and remove the printed
circuit board.
C
6 Separate the rechargeable battery from
the appliance by means of a screwdriver.
Do not connect the appliance to the mains again
after it has been opened!
Guarantee & service
If you need information or if you have a problem,
please visit the Philips website at
www.philips.com or contact the Philips
Customer Care Centre in your country (you will
find its phone number in the worldwide
guarantee leaflet). If there is no Customer Care
Centre in your country, turn to your local Philips
dealer or contact the Service Department of
Philips Domestic Appliances and Personal Care
BV.
ENGLISH12
Important
Avant d'utiliser l'appareil, lisez les instructions cidessous et conservez ce mode d'emploi pour un
usage ultérieur.
◗ Cet appareil est équipé d'un sélecteur de
tension automatique et est conçu pour une
tension secteur comprise entre 100 V et
240 V.
◗ Utilisez l'appareil uniquement avec le cordon
d'alimentation fourni.
◗ Si le cordon d'alimentation est endommagé, il
ne doit être remplacé que par un cordon
d'origine afin d'éviter tout accident.
◗ Évitez de mouiller l'appareil et le cordon
d'alimentation.
◗ Tenez l'appareil hors de portée des enfants.
◗ Utilisez, rechargez et conservez l'appareil à
une température comprise entre 15cC et
35cC.
◗ Cet appareil a été conçu uniquement pour
tailler la barbe. Ne l'utilisez jamais à d'autres
fins.
◗ Afin d'éviter tout accident, n'utilisez pas
l'appareil si le bloc tondeuse est endommagé
ou cassé.
Avant la première utilisation
◗ Chargez l'appareil complètement avant la
première utilisation (voir le chapitre Charge ).
◗ Une fois l'appareil chargé une première fois, il
est conseillé de l'utiliser jusqu'à ce que la
batterie soit complètement déchargée.
FRANÇAIS 13
Charge
C
1 Assurez-vous que l'appareil est éteint.
C
2 Insérez la fiche dans l'appareil.
3 Branchez le cordon d'alimentation sur la
prise secteur.
C
◗ Le voyant de charge s'allume pour indiquer
que l'appareil est en charge.
Une charge complète dure environ 1 heure. Le
voyant de charge clignote pour indiquer que la
batterie est complètement chargée.
Ne chargez jamais l'appareil pendant plus de
24 heures.
Un appareil complètement chargé offre une
autonomie d'utilisation de 40 minutes environ.
Optimisation de la durée de vie de la
batterie rechargeable
- Évitez de recharger l'appareil entre chaque
séance.
- Déchargez complètement la batterie deux fois
par an en laissant l'appareil fonctionner jusqu'à
l'arrêt du moteur.
- Évitez de laisser l'appareil branché sur le
secteur en permanence.
FRANÇAIS14
CHARGE
Utilisation de l'appareil
Peignez toujours votre barbe ou moustache avec
un peigne fin avant de la tailler.
Soyez prudent lorsque vous utilisez la tondeuse
pour la première fois. N'effectuez pas de
mouvements rapides, mais des mouvements
uniformes et tout en douceur.
Utilisation de la tondeuse sur secteur
◗ Pour utiliser la tondeuse sur secteur :
arrêtez-la, branchez-la sur le secteur et
patientez quelques secondes avant de la
mettre en marche.
Si la batterie est complètement déchargée,
attendez une minute avant de mettre l'appareil
sous tension car il pourrait ne pas fonctionner
immédiatement.
N'utilisez pas l'appareil sur secteur si la batterie
est complètement chargée.
Taille avec le sabot
C
1 Tournez le Precision Zoom Lock` sur la
position souhaitée (voir tableau).
Le réglage apparaît dans la fenêtre située en
dessous du Precision Zoom Lock`.
FRANÇAIS 15
9
9
Tableau de réglage de la longueur de
coupe
B
Si vous utilisez l'appareil pour la première fois,
commencez par sélectionner le réglage de
longueur maximum (9).
2 Mettez l'appareil en marche.
C
3 Placez la tondeuse sur la peau et déplacez-
la lentement dans le sens inverse de la
pousse des poils tout en exerçant une
légère pression.
Veillez à ce que la surface du sabot reste toujours
en contact avec la peau.
◗ Si des poils se sont accumulés dans le sabot :
4 Retirez le sabot de l'appareil.
FRANÇAIS16
Longueur de barbe
obtenue
1,5 mm
2,5 mm
4,0 mm
5,5 mm
7,5 mm
9,5 mm
12,0 mm
15,0 mm
18,0 mm
Réglage de la longueur de
coupe
1
2
3
4
5
6
7).
8).
9
Loading...