Action Clean
Razor Head
Cleaner
HQ100
Instructions for use
IMPORTANT
SAFEGUARDS
When using your Action Clean Razor Head
Cleaner, basic safety precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE.
1. Close supervision is necessary for any
appliance being used by or near children
or the disabled.
2. Use this Razor Head Cleaner for its intended
household use as described in this manual.
Do not use attachments or other cleaning
solutions not recommended by Philips
Electronics North America Corporation.
3. Never place this appliance on a soft surface,
such as a bed or a sofa, where solution may
spill. Do not tilt the unit.
4. Do not overfill chamber with liquid.
5. Do not rinse with water.
6. Never operate this unit if it is not working
properly or if it has been dropped or damaged. Return Razor Head Cleaner to an
Authorized Norelco Service Location for
examination and repair.
SAVE THESE
INSTRUCTIONS
If you need help, answers or
service, please call us at
1-800-243-3050
Features
• For assistance or the Authorized Norelco
Service Location nearest you, call toll free:
1-800-243-3050
Authorized Service Location information is available 24 hours a day, 7 days a week.
Before using your new Action Clean Razor Head
Cleaner, it is important to follow the instructions below:
• You do not need to remove cutters and combs
from Razor Head Assembly to clean them in the
Action Clean Razor Head Cleaner. The whole
assembly piece can be cleaned as a complete unit.
If you do remove cutters and combs be careful
not to interchange them as they are matched
sets. If you do interchange cutters and
combs, the shaving performance may be
adversely affected for the next few shaves
until the blades reseat themselves.
• Three Head Holder
• Two Head Holder
• Top
• Action Cleaning
Chamber
For
Assistance
Important
• Base
1
2
3
1. Turn the top of the Action Clean unit counterclockwise and pull top from Cleaning
Chamber. (Fig. 1)
2. Remove the filter unit from the Cleaning
Chamber. (Fig. 2)
3. Depending on your razor model, select either
the two or three head holder. Place it on top
of filter unit, ensuring that the three notches
of the holder fit in the slots of the filter unit.
Replace the filter unit into the Action Cleaning
Chamber, making sure that the filter unit clicks
down into place. (Fig. 3)
How to use your
Action Clean
Razor Head
Cleaner
8. When finished, remove top from Action
Cleaning Chamber and remove Razor Head
Assembly. (Fig. 8) Place Razor Head
Assembly on a paper towel to air dry. Make
sure Razor Head Assembly is completely dry
before placing it back on your razor.
9. DO NOT RINSE WITH WATER.
10. After each cleaning, spread one drop of
lubricating oil from the tube included,
Norelco Razor Lubricant Model AL80, or
one drop of mineral oil over each razor
head using your finger.
11. For consistently close and comfortable
shaves, you should clean your razor heads
every 4 - 6 weeks or when the display on
your razor tells you to do so. If your shave
is still not close enough, you may need new
replacement heads.
12. Change the filter and Action Clean Cleaning
Solution at least once a year. (Fig. 9,10,11)
13. Use only Norelco Action Clean Cleaning
Solution with filter, model HQ101, with this
unit.
9
1
2
6
7
8
4. Empty the contents of the Action Cleaning
Solution into the Cleaning Chamber. (Fig. 4)
5. Place Razor Head Assembly from razor (with
heads in place) onto Head Holder. (Fig.5)
6. Replace top on Cleaning Chamber, making
sure that it locks into place by turning clockwise until it “clicks” into place. (Fig. 6)
7. Clean heads by pumping the top on the Action
Cleaning Chamber for about 30 seconds.
(Fig.7)
10
11
5
4