Philips HD 7611-A Service Manual
Service
Service
Service
Service
Information
!
Coffee maker ”Café Therm”
HD 7611/A
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
Voltage
Frequency
Power consumption
Contents jug
Coloursetting
SERVICE INFORMATION
Thermostat
Thermostat
Thermal fuse
REPAIR INSTRUCTIONS
1.
Electrical circuit
When the appliance does not work, check the electrical
circuit. If the thermal fuse or thermostat prove defective,
the complete pump unit has to be replaced.
switch-off temp
switch-off temp
:
230V
:
50 - 60Hz
:
1200W
:
1200 cc
:
Black
cut-off temp
: 160°C (T1)
: 140°C (T2)
: 227°C
E
MSH coding
8827 611 00000
2.
De-scaling
If the water system is nearly or less clogged by scale
then operate the coffeemaker a few times with vinegar
or with a 10-15% solution of either vinegar-acid, citric
acid or tartar-acid, into cold tap water.
Do not use other de-scaling agents as these may harm
the appliance.
If this procedure does not restore the function, then switch
off the coffeemaker when the acid has passed through
during appr. 3 min. Keep the appliance in this condition
overnight and continue/repeat the cleaning operation.
After the de-scaling procedure, operate the coffeemaker
twice with tap water in order to rinse away any residual
substances.
Published by Philips Domestic Appliances and Personal Care Printed in The Netherlands Copyright reserved Subject to modification
3.
Pump unit removal
To separate the pump unit (item 24) from the hotplate
unit (item 22), the two plastic snaps at place A have to
be loosened. Then the pump unit can be lifted out easily.
4.
Exchanging the switch unit
Remove the panel (11) by carefully pushing a small
screwdriver into the chink at point A and moving it towards
to point B (see exploded view). Do not damage the housing.
If the panel has been damaged, get a new one.
Thermosjug handgrip removal (bajonet catch)
5.
To separate the handgrip 18 from the metal jug 20, lift up the
small cover B and unscrew the screw C. Then put a small
screwdriver at place D. Lift up the handgrip and turn
simultaneous the handgrip anti-clockwise 45°.
Before (re)placing the handgrip, apply a drop of detergent
to the sealing ring 19. This will make it easier to position the
handgrip by pushing it downwards and rotating.
©
4322 277 00130
99/11
PCS 104 727
HD 7611/A
1
2
14
3
15
16
20
17
B
4
18
8
19
C
D
21
20
M
A
X
10
15
13
5
6
8
11
6
9
7
4
5
3
MIN
A
B
A
13
10
12119
E
A
EMBOSSMENT
UPSIDE
22
23
24
7
1 4822 442 01697 Tank lid black
2 4822 466 12151 Spout disc black
3 4822 529 10432 Spout black
4 4822 256 10543 Filterholder black
5 4822 450 10314 Float orange
6 4822 450 10313 Window wall transparant
7 4822 462 11155 Stud
8 4822 402 11252 Jug lever black
10 4822 276 13973 Switch on/off salmon
11 4822 466 12152 Switch panel assy black
12 4822 410 12238 Insert disc black
13 4822 532 21371 Hose piece
14 4222 259 32970 Filter with spring aubergine 1)
15 4822 360 10435 Drip stop assy aubergine
16 4822 442 01698 Thermos jug lid black
25
17 4822 530 10459 O-ring 60 x 1,5
18 4822 498 10722 Carrier assy (pos. 18 + B + C) black
19 4822 532 12886 Sealing ring 70 x 5
20 4222 247 58130 Carrier cover black
21 4822 418 10412 Thermos jug complete black 2)
22 4822 466 11697 Hotplate unit therm
23 4822 360 50864 Valve hose unit
24 4822 466 11697 Pump unit 1200W 230V
25 4822 492 71174 Wire spring
Notes:
1) Optional part for use as an insert in item 14:
4822 480 50479 Permanent filter nylon
4822 480 10107 Permanent filter stainless steel
2) Commercial trade number of the complete thermosjug
is HD 7950
PCS 104 727
Loading...