Philips FWM-9000 Service Manual

Seu Mini Hi-Fi
System
FWM9000/
all
TABLE OF CONTENTS
Page
Technical specification ...........................................................1-15
Safety instruction......................................................................2-1
ESD protection.........................................................................2-2
Set Block diagram ..................................................................3-1
Set Wiring diagram............................................................. ....4-1
Main & Amp board
Circuit diagram............................................................6-1..6-3
Layout diagram.................................................................6-4..6-7
Key & Display
Circuit diagram....................................................................7-1
Layout diagram.................................................................7-2..7-3
Tuner
Circuit diagram....................................................................8-1
Layout diagram........................................................................8-2
Mcu & CD
Circuit diagram............................................................9-1...9-2
Layout diagram..................................................................9-3..9-5
Mechanical Exploded view..... .......................................... .....10-1
board
board
board
©
Copyright 2012 Philips Consumer Electronics B.V.Eindhoven,The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, inany form or by anymeans, electronic, mechanical,photocopying, or otherwise without the prior permissionof Philips.
Published by LX 1 Service Audio Printed in The Netherlands Subject to modication
Version 1.
215
0
3141 785 37540
Location of PC Boards
1-2
Technical Specification and Connection Facilities
3CD PART
Tuner Board
Main Board
Top key Board
Light Board
Display Board
Power key Board
Usb Board
Amp Board
VERSION VARIATION
Type /Versions:
Board in used:
Main BOARD display BOARD amp BOARD key BOARD
mic BOARD
tuner BOARD Switch Power BOARD cd BOARD mcu BOARD
Service policy
Switch power Board
/55
x/77
(ARGENTINA)
(LATAM)
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
M
M
C/M C/M
x/78
(BRAZIL)
C/M C/M
C/M C/M
C/M C/M
M
Ac cord Board
EQ Board
VFD Board
FWM9000
Type /Versions:
Features
Feature diffrence RDS VOLTAGE SELECTOR ECO STANDBY - DARK
* TIPS : C -- Component Lever Repair.
M -- Module Lever Repair
-- Used
/55
x/77
FWM9000
x/78
C/M C/M
1 - 3
FWM9000 SH 190 content List
1 GENERAL PART 1 - FRONT PANNEL SPECICFICATION 1 2 GENERAL PART 2 - BACK PANNEL SPECICFICATION 2 3 GENERAL PART 3 - GENERAL SPECICFICATION 3 4 GENERAL PART 4 - TECHNICAL SPECICFICATION 4 5 GENERAL PART 5 - AUDIO SIGNAL SPECICFICATION 5 6 GENERAL PART 6 - AUDIO SIGNAL SPECICFICATION 6 7 GENERAL PART 7 - CLOCK / TIMER SPECICFICATION 7 8 GENERAL PART 8 USB/SD-Card SPECICFICATION 8
9 GENERAL PART 9 - TUNER SPECICFICATION ( All ) 9 10 GENERAL PART 10 - CD / MP3 SPECICFICATION 10 11 GENERAL PART 11 - Ipod SPECICFICATION 11 12 GENERAL PART 12 - Microhone SPECICFICATION 12 13 GENERAL PART 12 - VERSION OVERVIEW SPECICFICATION 13
egaPnpotiprcseD.oN
1 - 4
DEPICTION Pos Description Page
CABINET
Diemensions with Boxes ( wxhxd ) 265mm X 382mm X 345mm Diemensions without Boxes ( wxhxd ) 1250mm X 340mm X 495 Weight ( inclusive packing )8.505KG Weight ( exclusive packing & batery )26KG
Remarks :
1 used into
Remark :
GENERAL PART 1 - FRONT PANNEL SPECICFICATION
Class No
FWM9000 All Version
11 A411 SH 190 - 1NAME :
KT CHECK:
DATE :
Material : HIPS / ABS / POM / V2 / SAN Finshing : Chrome Plate Units in Masstercarton Units in Dealercarton
Ver
Issued Date
1
12-Feb-09 2 3
1 - 5
10
NAME :
10
SH 190
2
A4
egaPnoitpircseDsoPNOITCIPED
CABINET
Diemensions with Boxes ( wxhxd )265mm X 382 mm X 345 mm Diemensions without Boxes ( wxhxd ) 1250mm X 340mm X 495mm Finshing : Chrome Plate
GENERAL PART 1 - BACK PANNEL SPECICFICATION
Class No
Material :HIPS
notracretssaM ni stinUgK5.8) gnikcap evisulcni ( thgieW notracrelaeD ni stinUgK62) yretab & gnikcap evisulcxe ( thgieW
FWM9000 All Version
-
-
KT CHECK:
DATE :
Ver
1 2 3
Issued Date
1 - 6
GENERAL DESCRIPTION MP3-USB Mini Hi FiSystem with Digital Tuner, 3CD/MP3 (2x350W+2x300W+2x150W) For FWM9000 Power Amplifier,VFD Display,Aux in ,Remote control Subwoofer Boxes of 8 Ohm x 2 LIFETIME : 7 Years
I II
III
Page
SAFETY requirements
/55 EN 60065,EN61000-3-2/EN61000-3-3
/05 EN 55013 / EN 55020 /79
RADIATION / IMMUNITY requirments ( EMC ) for 12 version only
CLIMATIC requirements ALL climates : + 5 Dregree till + 35 Degree MODERATE climates : + N.A till N.A Degree PERFORMANCE CLASSES
EN 60065 EN 60065
XXX
96-301
X
CMEytefaSnoisreV
CISPR 13
CISPR 13
99CCF56006 LU73/
CD-mp3Recorder ClockClass Tuner Supply + Amplifier USB
X X
8 11
31 RPSIC,56006 NE89/
02055 NE / 31055 NE56006 NE21/
POWER SUPPLY (SWITCHING MODE POWER SUPPLY) MAINS ( A.C. )
Version Voltage Selection Frequency
POWER CONSUMPTION
( DEMO mode " OFF " ) , NOM. A, INPUT Maximum :
ECO Power mode(Without display): < 0.5W Ref. to CRS Ref. to CRS
Quality : 0.8 % ( Major ) 2.0 % ( Mirror ) Reliability : 3.0 % ( C 42 ) Tested according to General Test Instruction refer to PHILIPS standary ( UAN -D1591 ) Measured according to PHILIPS standary ( UAN - L1059 ) unless other wise stated All not mentioned date, please refer to PHILIPS standary ( XUW - 0010 - JUNE 2001 )
Remarks
SWITCH POWER FOR AC100V TO 250V
/ 12/ 05 / 55/77/78/98 /61 /93 / 37
W052 <TUPNI ,A .MON , detarP 8/1 @
SRC ot feRSRC ot feRW1 <: )yalpsid htiw(ybdnatS
< 1W
< 0.5W
NOITABORPPASKRAMERDEVIRED
Class No
FWM9000 All Version
NAME : Andy Lai KT CHECK
GENERAL PART 1 - GENERAL SPECICFICATION
10 10 SH 190 - 3
DATE :
Ver
Issued Date
1
08-09-2011 2 3
A4
1 - 7
TECHNIAL DESCRIPTION
Total power 1500W, matching LOUDSPEAKER of 4 x 8 Ohm +2 x 4 Ohm. INPUT SOURCE, CD/MP TUNER USB AUX 3DSC ( Digital Sound Control ). IS ( Incredible Sound )
GENERAL PART OUTPUT stage Protection : Yes Temperature : Yes. Shorcircuit : Yes LoudSpeaker D.C. Protection : Yes.
INDICATORS Standby Mode Indicator : FTD display Clock active ECO Mode Indiicator : FTD turns off, ECO - Standby LED turn on
ELECTRICAL DATA (Main computer )
DSC : Rock, Pop, Jazz, Optimal
YES
MAX
IS : YES
WOOX : N/A
INTERCONNECTS Input Sensitity(
AUX
OUTPUT POWER ( * 1 )
Power output ( RMS )
Tuner output ( Lim '-6dB )
±2 dB)rated ouput power at 1 kHz and 10kHz.
: :
: : :
input leven 1mv rms(lim:2.5mv rms) Rs=600ohm
At THD = 10% (Measured with 20Hz-20KHz filter),(Per Channel measuremend )
Hum ( Volume control from min. till max. – 20 dB) Residual Noise ( Volume Minium ) < 60
Signal / Noise ( unweighted ) Subwoofer Out Hum( Volume minmun)
Line Output Voltage ( *1 )
) zHk 1 ta ( noitarapeS lennahCA/N: CAV
Main Channnel
Bd4±@ esnopser ycneuqerF:enohporciM
SUB. Channel Rear channel
output power 1kHz
L/R channel 300W ( Lim '-1dB )Power output ( RMS )
L/R Subwoofer channel 300W ( Lim '-1dB )Power output ( RMS )
3Bd04- ta recnereffiD lennahC
< 200 nW
45 55
<4
A.N) thgiR / tfeL ( tuO eniLnoitaludoM %08MA ZHK5.76 MF renuT
seYtuO refoowbuS ) 53 krT ,1 csiD oiduA ( kcart Bd 0 DC
A.NtuO laixaoC latigiD 73/ rof Vm009 ~ Vm053 :miL Vm006 :roN A.NtuO retsooB55/ rof V5.2 ~ V5.1 :miL V2 :roN
40HZ-16KHZ(reference 1KHZ)
40HZ-125HZ(reference 63HZ)
200HZ-16KHZ(reference 1KHZ)
) Bd1-' miL ( W051lennahc raeR R/L) SMR ( tuptuo rewoP
dB
nW
dB dB
µW
mhO 23 ta %2.0 -/+ V7.0enohpdaeH ) 53 krT ,1 csiD oiduA ( kcart Bd 0 BSU
LOUDSPEAKER ( BOXES ) Please to package document of Speaker Box Assy
Rated Impedance FRONT:L/R : 8 Ohms X2 at 40Hz to 16 KHz Subwoofer L/R : 8 Ohm x2 at 40HZ to 100HZ Rear: L/R : 4 Ohms X2 at 200Hz to 16 KHz Remarks ( *1 ) Measurement output power just connect 2 channel loads. Electrical parameters are to be measuremend at specker terminals across 8 Ohm load ( pure resistor ) with rated input signal in AUX mode; DSC setting in Jazz mode with DBB OFF IS off and OSM unless specified otherwise Measurement output power only for AUX model and CD model of used audio analyzer equipment.
(*2) All speaker "R" channel "+ "connect to equipment " + "for measurement. All speaker "L" channel "- "connect to equipment " + "for measurement (because all "L"channel output are reverse ).
GENERAL PART 1 - TECHNAICAL SPECICFICATION
FWM9000 All Version
NAME : Andy Lai KT CHECK
DATE :
10 10 SH 190 - 4
Ver
Issued DateClass No 1 2 3
08-09-2011
A4
1 - 8
AUDIO SIGNAL PROCESSING
MP3-USB Mini Hi Fi System with Digital Tuner , 3 CDC-MP3,(Main:2×350W+Rear:2×150W+SUB:2x300W) Universal Class D Power Amplifier 1 ) DSC ( Digital Sound Control ) Select AUX as input source with the following set conditions: Inject sine wave 500mV at 1 KHz to L/R channels of AUX-IN socket. Set DSC to JAZZ(Flat) mode and switch off DBB. Refence level for DSC's without DBB on=1W. Refence level for DSC'S with DBB on=1.2V at the speaker terminal . Inject sine wave 500mV-2.4V to AUX-IN socket with frequencies indicated in Table 1. For FWM998 Subwoofer in put 500mW 60HZ @ 3R (Main computer )
Tabel 1a ( Tolerance ± 3dB )
Frequency
60 Hz (SUB)
1K((SUB) 0 1 kHz (host computer) 0 10 kHz(host computer) 0 2
JAZZ POP TECHNO
0
DSC Modes with DBB Off
4 0 0 0
OPTIMAL
6
0
2 0 0 2-4
Tabel 1b ( Tolerance ± 3dB )
Frequency
60 Hz (SUB) 4
1khz(SUB) 0 0 0
1 kHz (host computer) 0
Tabel 1b ( Tolerance ± 3dB )
Frequency
60 Hz (SUB) 10 16
1 kHz(SUB) 0
1khz (host computer) 0 0 0
10 kHz (host computer)
Tabel 1b ( Tolerance ± 3dB )
Frequency
1khz(SUB) 0
1 kHz(host computer) 0
10 kHz(host computer)
2 ) DBB ( Dynamic Bass Boot )
Select AUX as input source with the following set conditions : Inject sine wave 500mV at 1kHz to L/R channels of AUX - IN socket. Set DSC to JAZZ(Flat) mode and switch off DBB, Reference level for the test is 500mW on the speaker terminals. Tabel 2 of FWM998( Tolerance ± 3dB )
JAZZ POP TECHNO
JAZZ
JAZZ
16
2
DSC Modes with DBB 1 ON
8 8
2
DSC Modes with DBB 2 ON POP TECHNO
0
4
DSC Modes with DBB 3 ON POP TECHNO
0 0 0 0 6 0
-410 kHz (host computer) 0
16
0
2-0
02)BUS( zH 06
OPTIMAL
6 0 00 0 2
OPTIMAL
13
0 0 2
OPTIMAL
2020
0 0 4
Frequency DBB OFF
60 Hz(SUB)
1 Hz(SUB) 0
10K Hz(host computer)
Class No
NAME : Andy Lai
KT CHECK
0
0 0 0
GENERAL PART 1 - GENERAL SPECICFICATION
FWM9000 All Version
10 10
DATE :
DBB 1
4
0 0 0
DBB 2
8 12
SH 190 - 5
DBB 3
01khz(host computer) 0 0 0
2
Ver
Issued Date
1
08-09-2011 2 3
A4
1 - 9
AUDIO SIGNAL PROCESSING
MP3 - USB Mini Hi Fi System with Digital Tuner , 3 CDC-MP3, (Main:2×350W+SUB:2×300W+Rear:2x150W) Universal Class D Power Amplifier
3 ) IS ( Incredible Sound )
Select AUX as input source. Inject sine wave 2V at 1kHz to AUX-IN socket, two channel at a time (input level 600mV for /37,2V for /55 ). Set DSC to JAZZ ( Flat ) mode and switch of DBB, OSM & INCREDIBLE SURROUND. Adjust volume level to obtain 1W across 3 OHM load at L/R speaker output. Inject sine wave 2V to AUX-IN socket withfrequency indicated in Table 3 (input level 600mV for /37,2V for /55 ).
Table 3 ( Tolerence ± 3 dB )
FREQ
60 Hz 1 kHz
10 kHz
Note : The above specs also apply to right channel.
4 ) DSC Mode ( Jazz , Rock, Techno and Optimal )
The VEC modes are software controlled by switching the combination between DBB and DSC modes as show in Table 4.
VEC MODE
Jazz POP
Optimal
Note : When these modes are activ DBB and DSC will not be displayed
5 ) MAX ( Maximum Sound )
Select AUX as input source. Inject sine wave 2V at 1kHz to AUX-IN socket, one channel at a time (input level 600mV for /37,2V for /55 ). Set DSC to JAZZ ( Flat ) mode and switch of DBB, OSM & INCREDIBLE SURROUND. Adjust volume level to obtain 1W across 3 OHM load at L/R speaker output. The 1W level will be used as 0 dB reference Inject sine wave 2V to AUX-IN socket withfrequency indicated in Table 5 (input level 600mV for /37,2V for /55 ).
INPUT LEVEL
LEFT RIGHT LEFT RIGHT
2V ­2V - 0 ­2V -
DBB Level preset
DBB OFF
DBB 3
DBB 2
- 0.5 dB - + 3.0 dB -5 dB
3 BBDonhceT
OUTPUT LEVEL
LEFT RIGHT
+2.0 dB- 1.0 dB -
+ 3.5 dB 0 dB
NO SIFFO SI
- 15 dB
Class No
NAME : Andy Lai KT
FREQ Max OFF 60 Hz 1 kHz
10 kHz
-1 0 +5
-1
GENERAL PART 1 - AUDIO SIGNAL SPECICFICATION ( 2 )
FWM9000 All Version
CHECK DATE :
Max ON
+19
+7
10 10 SH 190 - 6
Ver Issued Date
1
08-09-2011 2 3
A4
1 - 10
TECHNIAL DESCRIPTION SOFTWARE IMPLEMENTED CLOCK / TIMER FUNCTION WITH 12MHZ QUARTZ OSCILLATOR.
GENERAL PART
remiT dna kcolC :gnitteS remiT
BSU ro renuT ro DC :edoM puekaW remiT
gnitteS tsaL :puekaW ta emuloV
No of Timer Settings : 1 Clock Accuracy
INDICATORS
Remark
: Nom : 1 sec/day Limit : 2 sec/day
DFV :epyT yalpsiD
.noisrev rehto rof srh42 ,noisrev 73/ rof rh21 :gnitteS emiT skrameR
KT
Class No
CLOCK / TIMMER SPECICFICATION
FWM9000 All Version
CHECK DATE :
Ver Issued Date
1
08-09-2011 2 3
7 - 091 HSiaL ydnA : EMAN 10 10
A4
1 - 11
(*2)
"L"
TECHNIAL DESCRIPTION USB See also SH 190 USB Audio Module (300605)
Measurment are directly done at the coonector on the board GENERAL PART
Measurement are directly done at the connector on CDC board
Output Resistance
Channel Unbalance
Channel Crosstalk ( ( 0 dB, 1 KHz ) ) >= 45dB ( 0 dB, 1 KHz ) >= 45dB
< = 1.5 kOhm
< = +/- 3 dB
%2=<) zhK1 ,Bd0 ( esioN + DHT
40HZ-16KHZ(reference 1KHZ)
noitacificepSnoitpircseD
Bd1 -/Vm038) zhK 1 ,Bd) ( mho k 33 = LR egatloV tuptuO
) dethgiew - A (Bd55 =>) dethgiew - A ( ) zHk1,Bd0 ( oitaR esioN ot langiS
FWM9000 Frequency response @±4
40HZ-100HZ(Reference 63HZ)
200HZ-16KHZ(Reference 1KHZ)
USB Measurement at Set Level (*2)
Electrical Parameters are to be measured at speaker teminals across 3 ohm load with 500mW output and DSC setting in Jazz Mode
Description
Channel Crosstalk ( 0 dB, 1 KHz )
Channel Unbalance ( 0 dB, 1 KHz )
Specification
>= 45dB (with 1 KHz filter )
) dethgiew - A ( ABd55 =>) zHK 1 ,Bd 0 ( oitaR esioN ot langiS
< +/- 3dB
SD-CARD Measurement at Set Level (*2)
Electrical Parameters are to be measured at speaker teminals across 3 ohm load with 500mW output and DSC setting in Jazz Mode
Description
Signal to Noise Ratio ( 0 dB, 1 KHz )
Remarks :
All speaker "R" channel "+"connect to equipment "+"for
All speaker
channel "- "connect to equipment " + "for measurement
Specification
) retlif zHK 1 htiw( Bd54=>) zHK 1 ,Bd 0 ( klatssorC lennahC
>= 55dBA ( A - weighted )
Bd3 -/+ <) zHK 1 ,Bd 0 ( ecnalabnU lennahC
Class No
USB AND SD-CARD SPECICFICATION
FWM9000 All Version
10
CHECK
DATE :
01iaL ydnA : EMAN
SH 190 -8
Ver
1 2 3
Issued Date
08-09-2011
A4
1 - 12
TECHNIAL DESCRIPTION TUNER used SI4730 soultion GENERAL PART
FM( 12 ) 87.5 - 108.00 MHz
AM (12) 531 - 1602 kHz
AERIAL FM : PIGTAIL ANT WIRE 300 Ohm(for/37) 75ohm for 55/12 AM : FRAME ANT. 18.1 uH with shielding
INDICATORS VFD
DIRG GNINUTECNARELOTEGNAR EVAW
zHk 001NOISICERP ZTRAUQzHM 00.801 - 5.78 ) 73/55 (MF
50KHZ
zHk 01 NOISICERP ZTRAUQzHk 0071 - 035 )73/55( MA
zHk 9 NOISICERP ZTRAUQ
A.M
Amplification Reverse AGC Figure of Merit Distortion ( RF 50mV, M 80% ) IF
Search Tuning Sensitivity S/N Ratio
MW 610 kHz
MW 1440 kHz
FM 98 MHz
FM 108 MHz
Nom.
Lim.
Nom.
Lim.
Nom.
Lim.
Nom.
Lim.
: 30 25 dB : 3 5 % : 450
: α26 +/-10 dB
45 40 dB
ytivitisneS detimiL esioN egnaR evaW α langiS egraLBd 62
4000
Uv/m 28db
1500 4000
18
dBf 40db 65db 116 dBu 30db 22 dBf 18 22
dBf 40db 65db 116 dBu 45db
dBf 30db
- 3 dB Limiting Point Amplification Reverse Distortion ( RF 1mV, Frq Dev.75 kHz ) Stereo - 46 dB Quieting Crosstalk (RF1mV, Freq Dev.40kHz ) IF
Image Rejection
IF Rejection
32 db 28db
F.M.
32db
28dbuV/m
60db 108 dBu
Nom
Limit : 17 23.5 dBf : 0
4-Bd4-2 - :
dB : 2 3 % : 46 49 dBf : 25 : 10.7
24-30
± 0.03 MHz
dB
81zHk3 ±
dBf19-35
50 45 dB
Selectivity
S9 / 300kHz
22db3500 uV/m 1000mv/m
500mv/m 18db24db
1000mv/m
22db 18dbuV/m 28db 24db 500mv/m
108 dBu30db 60db
25db
25db
tinUtinUtimiLmoN
RemarksMAX.Sens -6dB
Class No
FWM9000 All Version
KT CHECK
DATE :
TUNER SPECICFICATION
01iaL ydnA : EMAN
10 SH 190 - 9
Ver Issued Date
1
30-Nov-09 2 3
A4
1 - 13
.
r
r
t
t
TECHNIAL DESCRIPTION
CD + MP3 - Part Specifications (CD MECHAISM DA11VF OF SANYO )
Inpu
Active components
Outpu
Motor Logic control
Signal processsing D/A converte
HF-preamplifie
Servo processor
Active components
AUDIO part: Measurement with Audio Signals Disc-783 7104 078 04911 on spkeakers or Headphone socket with nom.load
UnitmiLmoNretliF nretxEnoitpircseD De-emphasis Frequency accuracy N/A ± 0.5 %
Frequency Response ( 40 Hz - 16 kHz ) reference 1kHz
FRONT CH.
requency Response ( 200Hz - 16 kHz )reference 1kHz Rear CH.) Frequency Response ( 40Hz - 100Hz ) reference 63Hz Signal to Noise Ration ( Unweighted ) Signal to Noise Ration ( A - weighted ) Crosstalk ( 1kHz ) ( A - weighted )
Hum & Noise (filer 20kHz) ( *1 ) THD (1KHz -6dB) THD (10KHz -20dB) <1
REMARKS:
1. Amplification reserve for CD = +2dB ('±2dB),Ref.Level for CD is a 0dB track instead of a .-6dB track.
SUB. CH.
Playability :(acc.To AR 30-05-239 )
Limit
Skew 0.6mm
Bad HF track
Hwavy fingerprint
Playback position Solid, Normal position (Set is located on a flat surface, floor)
15us / 50us Switchable via Subcode information
1 3
L/R
L/R L/R
60 65 55
>= 45dB
1 1.5
'± 4
± 4
50
<3
csid tseTlacipyT
dBA
dBA
mV
A8 sissahc buS fo 11 ONTtcefed elbidua oNtnirpregniF
A8 sissahc buS fo 8 ONTtcefed elbidua oN
A8 sissahc buS fo 01 ONTspolp/repmuj kcart oN
dBChannel Unbalance dB
dB dB
dB dB
%0.2 <1 %
)09942 990 4017(A444 CBS fo 9 ,7 ONTmu009mu006egdeW
)06942 990 4017( csid mu002 fo 42 ,1 ONTmu002mu051cirtneccE
)09942 990 4017( A444 CBS fo 31 ONTmu008mu005tod kcalB
)06282 990 4017( weks mm6.0 fo 6,1 ONTtcefed elbidua oN
1. Playback of above mentioned tracks possible wihout track loss or audible defects.
2. Double black dot, max. diameter, thin/disk is according to PQR or AR 30-05-239
3. This unit can playback (only) CD-R or CD-RW discs. For performance specification, Please refer to module. specification of CD99 (3103 308 52190)
Remarks :
4. (1)All speaker "R" channel "+ "connect to equipment " + "for measurement. (2) All speaker "L" channel "- "connect to equipment " + "for measurement (because all "L"channel output are reverse )
Class No
CD / MP3 SPECICFICATION
FWM9000 All Version
NAME : Andy Lai KT
CHECK
DATE :
10 10 SH 190 -10
Ver
1 2 3
Issued Date 08-09-2011
A4
Loading...
+ 28 hidden pages