Philips FWM799/22, FWM799/21 User Manual

Mini HiFi System

User manual Manuel d'utilisation Manual del usuario Benutzerhandücher Gebruikershandleidingen Manuale per l'utente Användarhandböckerna Brugermanual Käyttöoppaita Manual do usuário

 

FWM799

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362 5 Amp,

A.S.T.A. or BSI approved type.

3 Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp.

Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).

¶ As these colour s may not correspond with the

colour markings identifying the terminals in your plug, proceed as follows: – Connect the blue wire to the terminal marked N or coloured black. – Connect the brown wire to the terminal marked L or coloured red. – Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.

Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

Italia

DICHIARAZIONE DI CONFORMITA’

Si dichiara che l’apparecchio FWM799, Philips risponde alle prescrizioni dell’ar t. 2 comma 1 del D.M. 28 Agosto 1995 n. 548.

Fatto a Eindhoven

Philips Consumer Electronics

Philips, Glaslaan 2

5616 JB Eindhoven, The Netherlands

Norge

Typeskilt finnes på apparatens underside.

Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten.

For å redusere faren for brann eller elektrisk støt, skal apparatet ikke utsettes for regn eller fuktighet.

CAUTION

Use of controls or adjustment or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten muutto saattaa altistaa vaaralliselle säteilylle tai muille vaarallisille toiminnoille.

AUX/GAME

USB PC LINK

VOL

DSC WOOX LEVELVAC

Energy Star

As an ENERGY STAR

Par tner, Philips has determined that this product meets the ENERGY STARR guidelines for energy efficiency.

1 2

≤

™

4 5 6

7 8

0 !

@ # $

∞

* 7

8 0

§ ( ≥

• &

)

(

‹

¤ ⁄

º 4 ! ª @

Index

Advarsel: Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for stråling.

Bemærk: Netafbryderen er sekundært indkoblet og ofbryder ikke strømmen fra nettet. Den indbyggede netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i stikkontakten.

Klass 1 laseraparat Varning! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

Observera! Stömbrytaren är sekundärt kopplad och bryter inte strömmen från nätet. Den inbyggda nätdelen är därför ansluten till elnätet så länge stickproppen sitter i vägguttaget.

English ------------------------------------------------ 6

English

Français -------------------------------------------- 30

Français

Español --------------------------------------------- 54

EspañolDeutschNederlandsItalianoSvenskaDanskSuomi

Deutsch --------------------------------------------- 78

Nederlands -------------------------------------- 102

Italiano -------------------------------------------- 126

Svenska ------------------------------------------- 150

Dansk --------------------------------------------- 174

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja roiskevedelle.

Huom. Toiminnanvalitsin on kytketty toisiopuolelle, eikä se kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa.

Suomi --------------------------------------------- 198

Português ---------------------------------------- 222

Por tuguês

 ----------------------------------------- 246



Contents

English

General Information

Supplied accessories ............................................ 7

Environmental information ................................ 7

Care and safety information .............................. 7

Sound control ..................................................... 18

wOOx sound ................................................... 18

Incredible Surround ........................................ 18

Digital sound control ..................................... 18

Virtual ambience control ............................... 18

Functional Overview

Main unit and remote control ....................... 8~9

Control buttons available on the

remote control only ......................................... 9

Connections

Step 1: Connecting FM/MW antennas ........... 11

Step 2: Connecting the speakers .................... 11

Step 3: Connecting to PC ................................. 11

Step 4: Connecting to game console ............. 11

Step 5: Connecting the AC power cord ........ 12

Step 6: Connecting the Power..............................

Booster ................................................................. 12

Step 7: Inserting batteries into the remote

control .................................................................. 12

Using the remote control to operate

the system ........................................................ 12

Gameport Operations

About Gameport ............................................... 13

Preparation before use ..................................... 13

Starting operation .............................................. 13

USB PC Link

Quick setup guide .............................................. 14

PC system requirement ................................. 14

Software installation ....................................... 14

Using MusicMatch software .......................... 15

Connecting USB PC link ................................... 15

Philips Sound Agent 2 ..................................... 16

Enabling digital CD audio output ................ 16

Basic Operations

Switching on/off ................................................. 17

Switching to active mode .............................. 17

Switching to Eco Power standby mode ..... 17

Switching to standby mode (view clock) ... 17

Demonstration mode ........................................ 17

Setting the clock ................................................. 17

Dimming system’s display screen .................... 18

Volume control ................................................... 18

Disc Operations

Playable discs ....................................................... 19

Loading discs ....................................................... 19

Basic playback controls ..................................... 19

Playing an MP3 disc ............................................ 20

Repeat and shuffle .............................................. 20

Repeat play ....................................................... 20

Random play ..................................................... 20

Programming the disc tracks ........................... 21

Checking the programme ............................. 21

Clearing the programme ............................... 21

Tuner Operations

Tuning to radio stations .................................... 22

Presetting radio stations ................................... 22

Using the plug and play .................................. 22

Automatic presetting ..................................... 22

Manual presetting ............................................ 22

Selecting a preset radio station ....................... 23

Deleting a preset radio station .................... 23

RDS ....................................................................... 23

Scrolling through RDS information ............. 23

Setting the RDS clock .................................... 23

NEWS ................................................................... 24

Switching on NEWS function ....................... 24

Timer Operations

Setting the timer ................................................. 25

Activating/Deactivating the timer ............... 25

Setting the sleep timer ...................................... 26

Other Connection

Listening to an external source ...................... 26

Recording to an external device ..................... 26

Specifications ........................................... 27

Troubleshooting ............................. 28~29

General Information

This product complies with the radio interference requirements of the European Community.

Refer to the type plate on the rear of the system for identification and supply ratings. For users in the U.K.: please follow the instructions on page 2.

Supplied accessories (page 3 – P1)

– USB PC Link installer disc – USB cable – Remote control and two AA batteries. – MW loop antenna – FM wire antenna – Video cinch cable (yellow) –AC power cord –Power booster amplifier package:

– one power booster amplifier – one pair of speakers – one cinch cable (GN/BU)

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).

Your system consists of materials which can be recycled and reused if disassembled by a specialised company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Care and safety information

(page 3 – P2)

Avoid high temperature, moisture, water and dust

– Do not expose the system, batteries or discs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). Always keep the disc tray closed to avoid dust on the lens.

– No objects filled with liquid, such as vases, shall be placed on the apparatus. – No naked flame sources, such as lighted candles, shall be placed on the apparatus.

Avoid condensation problem

– The lens may cloud over when the system is suddenly moved from cold to warm surroundings, making it impossible to play a disc. Leave the system in the warm environment until the moisture evaporates.

Do not block the vents

– In a cabinet, allow about 10cm (4 inches) of free space all around the system for adequate ventilation.

Care of disc

–To clean a CD, wipe it in a straight line from the centre towards the edge using a soft, lint-free cloth. A cleaning agent may damage the disc! –Write only on the printed side of a CDR(W) and only with a soft felt-tipped pen. – Handle the disc by its edge, do not touch the surface.

Care of the cabinet

– Use soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.

Finding a suitable location

– Place the system on a flat, hard, and stable surface.

Built-in safety circuit

– Under extreme conditions, this system may switch to standby mode automatically. If this happens, let the system cool down before reusing it (not for all versions).

Power saving

– This system is designed to use less than 1W of electricity when switched to Eco Power standby. Disconnect the AC power cord from the power outlet when not in use.

English

Functional Overview

English

Main unit and remote control

1 ECO POWER indicator

– Lights up when the system is in the Eco Power

standby mode.

2 STANDBY ON B

– Switches to the Eco Power standby mode or

turns on the system.

– *Switches to the standby mode.

3 Display screen

4 CLOCK•TIMER (CLK/TIMER)

– *Enters clock or timer setting mode.

5 RDS•NEWS

– In tuner mode, selects RDS information. – In other modes, turns on/off news.

6 CD / TUNER / USB PC LINK /

AUX•GAME

– Selects the relevant active mode. – CD: toggles between DISC 1~5. – TUNER: toggles between FM and MW band. – AUX•GAME: toggles between AUX and

GAMEPORT mode.

7 PREV•PRESET 4 (TITLE) (í)

NEXT•PRESET 3 (TITLE) (ë)

– CD: selects a track or selects a title from MP3

disc.

– TUNER: selects a preset radio station. – CLOCK: sets the minutes. – USB PC LINK: selects your desired playlist.

8 STOP• DEMO STOP Ç

– Exits an operation. – CD: stops playback or clears a programme. – TUNER: *erases a preset radio station. – USB PC LINK: stops playback.

(only on the main unit)

– *Tu r ns on/ off the demonstration mode.

9 SEARCH•TUNING

(ALBUM/PLAYLIST) ( à á)

– CD: *searches backward/forward. – MP3-CD: select an album – TUNER: tunes the radio frequency up /down. – CLOCK: sets the hours. – USB PC LINK: selects a playlist.

0 PLAY•PAUSE ÉÅ

– CD: starts / pauses playback. – USB PC LINK: starts / pauses playback.

(only on the main unit)

– TUNER: *enters Plug & Play mode and /or starts

preset radio station installation.

! wOOx 1/2/3 (wOOx LEVEL)

– Selects different type of enhanced wOOx sound

settings (wOOx 1, wOOx 2 or wOOx 3).

@ MIX IT (GAME MIX IT)

– Mixes the game sound with your favourite music

from one of these music source (CD, TUNER, USB PC LINK or AUX).

# MODE (GAME SOUND)

– Selects different type of equaliser setting for

Gameport (SPEED, PUNCH or BLAST).

$ Connect the USB cable between the system and

PC’s USB port.

% GAME VOLUME

– Adjusts the game’s output volume level.

^ VIDEO

– Use a video cable to connect to your game

console’s video output.

AUDIO L. / AUDIO R.

– Use a audio cable to connect to your game

console’s left/ right audio output.

& INC SURR

–Turns on /off the Incredible Surround effect.

DSC / PRESET

– Selects different type of preset sound equaliser

settings (OPTIMAL, JAZZ, ROCK or POP).

VAC / REVERB

– Selects different type of environment ambience-

based equaliser settings (HALL, CINEMA, CONCERT, CYBER or ARCADE). *PRESET and REVERB environment sound modes are only available when the optional software, Philips Sound Agent 2 is activated during USB PC Link applicaion.

* MASTER VOLUME (VOL +-)

– Adjusts the volume level.

* = Press and hold the button for more than two seconds.

( PROG (PROGRAM)

– CD: starts or confirms track programming. – TUNER: starts *automatic/manual preset

programming.

– CLOCK: selects 12- or 24-hour clock display.

) n

– Plug in the headphones jack. The speakers

output will be cancelled.

¡ VU meters

– Indicates signal strength of left/right channel.

™ iR SENSOR

–Point the remote control towards this sensor.

£ Disc trays (1~5)

≤ OPEN•CLOSE 0 (DISC 1~5)

– Opens/closes the individual disc tray.

Control buttons available on the remote control only

∞ CD 1~5

– Selects a disc tray to playback.

§ REPEAT

– Repeats a track / disc/all programmed tracks.

≥ DIM

–Turns on / off the dim mode.

• SLEEP

– Sets the sleep timer function.

ª MUTE

– Mutes or restores the volume.

º TIMER ON/OFF

–Turns on / off the timer function.

⁄ SHUFFLE

–Turns on /off the random play mode.

¤ DISPLAY

– Displays the album and title name for MP3 disc.

‹ B

– Switches to the Eco Power standby mode. – *Switches to the standby mode.

Functional Overview

English

* = Press and hold the button for more than two seconds.

Connections

English

Booster

Speaker

(right)

Speaker

(right)

BOOSTER IN

SPEAKERS 6Ω

–

RLR

–

Booster

220V- 240V

Speaker

(left)

AC power cord

MW loop 

antenna

DO NOT OPEN

CAUTION

RISK OF ELECTRIC SHOCK

NE PAS OUVRIR

AVIS

RISQUE DE CHOC ELECTRIQUE

POWER SWITCH

OFF

AC MAINS

VOLTAGE

SELECTOR

110V- 127V

FM wire antenna

AM 

VIDEO OUT

(CVBS)

ANTENNA

BOOSTER

OUT

FM ANTENNA

SUBWOOFER 

SPEAKERS 8Ω

LINE  OUT

AUX/ CDR 

OUT

– –

MAINS

Speaker

(left)

AC

AC power cord

Front panel

OUT

Game console

Connections

Warning! – Use only the supplied speakers. The combination of the main unit and speakers provide the best sound. Using other speakers can damage the unit and sound quality will be negatively affected. –Never make or change connections with the power switched on. – Connect the AC power cord to the power outlet only after you have finished hooking up everything.

Step 1: Connecting FM/MW

antennas

– Place the MW loop antenna on a shelf or attach it to a stand or wall. – Extend the FM antenna and fix its ends to the wall. – Adjust the position of the antennas for optimal reception. –Position the antennas as far as possible from a TV, VCR or other radiation source to prevent unwanted noise. – For better FM stereo reception, connect external FM antenna.

Step 2: Connecting the

speakers

Connect the speaker wires to the SPEAKERS terminals, right speaker to “R” and left speaker to “L”, coloured (marked) wire to “+” and black (unmarked) wire to “-”. Fully inser t the stripped portion of the speaker wire into the terminal as shown.

Notes: – Ensure that the speaker cables are correctly connected. Improper connections may damage the system due to short-circuit. – Do not connect more than one speaker to any one pair of +/- speaker terminals.

Step 3: Connecting to PC

Use the supplied USB cable to connect the system to your personal computer’s USB port. After installing the USB PC LINK application software onto your PC, you can play your music collection via the system (refer to “USB PC Link”).

Step 4: Connecting to game

console

IMPORTANT! Gameport inputs are solely for game console only.

a. Use the game console’s video cable (not

supplied) to connect its video output to the GAMEPORT-VIDEO terminal.

b. Use the game console’s audio cables (not

supplied) to connect its audio outputs to the GAMEPORT-AUDIO L. / AUDIO R. terminals.

c. Use the video cable (yellow) to connect the

VIDEO OUT terminal to the video input on

the TV for viewing.

Notes: – On the TV, the Video Input jack is usually yellow and might be labeled A/V In, CVBS, Composite or Baseband. –To avoid magnetic interference, do not position the front speakers too close to your TV. –For optimal enjoyment of your Gaming Experience, please do not connect the TV’s AUDIO OUT to the audio system’s AUX IN (R/L) terminals. – If you want to listen to your favorite movies/TV programs through the Philips Mini System, please disconnect the Game Console connection on the front of the set to avoid any unwanted noise.

English

Connections

English

Step 5: Connecting the AC

“AUTO INSTALL - PRESS PLAY” may appear on the display panel when the AC power cord is plugged into the power outlet for the first time. Press ÉÅ on the main unit to store all available radio stations (page 3 – P3) or press Ç to exit (refer to “Tuner Operations”).

power cord

Step 7: Inserting batteries into

the remote control

Step 6: Connecting the Power

Booster

BOOSTER IN

POWER SWITCH

SPEAKERS 6Ω

–

RLR

–

OFF

AC MAINS

VOLTAGE

SELECTOR

110V-

220V-

127V

240V

DO NOT OPEN

CAUTION

RISK OF ELECTRIC SHOCK

NE PAS OUVRIR

AVIS

RISQUE DE CHOC ELECTRIQUE

1 Connect the BOOSTER OUT (Right and

Left) terminals of the mini system to the power booster amplifier BOOSTER IN (Right and Left) terminals respectively.

2 Connect the speaker wires to the BOOSTER

SPEAKERS terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-".

3 Set the VO LTA GE SELECTOR to the local

power line voltage.

4 Plug in the AC mains to the wall socket. 5 Switch on the POWER SWITCH to activate

the power booster amplifier.

6 Press STANDBY ON button to switch the

system ON or to Standby mode.

7 Rotate the VOLUME control to adjust the

loudness of the power booster amplifier.

1 Open the batter y compartment cover. 2 Inser t two batteries type R06 or AA, following

the indications (+-) inside the compartment.

3 Close the cover.

Using the remote control to operate the system

1 Aim the remote control directly at the remote

sensor (iR) on the main unit.

2 Select the source you wish to control by

pressing one of the source select keys on the remote control (for example CD, TUNER).

3 Then select the desired function (for example

ÉÅ, í, ë).

CAUTION! – Remove batteries if they are exhausted or will not be used for a long time. – Do not use old and new or different types of batteries in combination. – Batteries contain chemical substances, so they should be disposed of properly.

Gameport Operations

MODE

GAME SOUND

GAME

About Gameport

Gameport allows you to connect your game console to this mini system which enables you to enjoy a total game immersion experience through powerful sound output.

Preparation before use

Rear panel

•AU

7 6

Front panel

Game console

1 Connect your game console’s video and audio

output to the GAMEPORT video and audio inputs respectively (refer to “Connections – Connecting to game console).

2 Connect your TV’s video input to the VIDEO

OUT (CVBS) on the rear panel.

3 Connect all the AC power cords to the power

outlet.

5 Press AUX•GAME until “GAMEPORT” is

displayed.

6 Press MODE (or GAME SOUND on the

remote control to select the type of sound setting that best suits the game : SPEED, PUNCH, BLAST or OFF.

7 If you like to mix your game sound with your

favourite music, press MIX-IT to select the desired music source : CD, TUNER, USB PC LINK, AUX or OFF.

CD ™ “MIX-CD” TUNER ™ “MIX-TU” USB PC LINK ™ “MIX-USB” AUX ™ “MIX-AUX” OFF ™ “MIX-OFF”

8 If necessar y, star t to play your chosen mixer

source.

9 Play your favourite game.

To adjust the game console’s volume level

● Adjust GAME VOLUME.

To change the mixer source

● Press MIX-IT.

To control the current active mixer source

● Press the respective source button (for example,

CD, TUNER) on the remote control, then select the desired function (for example É, í, ë). For example, if CD is the mixer source and you want to change the disc tray, you have to press CD, then press CD 1~5 to select the desired disc tray.

English

Starting operation

4 Tu rn on the TV and set to the correct

video-in channel. The TV’s video input channel may be called AUX(iliary) IN, AUDIO/VIDEO (A/V) IN, EXT 1, etc. These channels are often near channel 00 on your TV. Or, your TV remote control may have a button or switch that chooses different video modes. See your TV manual for details.

Notes: –You can only activate GAME VOLUME and MIX-IT while in the game source mode. – If your game console is switched on, the video image will always appear on the TV even though you are not in the gameport mode.

USB PC Link

English

IMPORTANT! – Make sure the mute setting on your PC control panel is deactivated to ensure you get the sound from your audio system!

Quick setup guide

PC system requirement

–Windows 98SE/ ME/2000/XP – Intel Pentium MMX200 or higher – CD-ROM drive – USB port – Free hard disk space: 80 MB for the

software

Software installation

1 Tu rn on your PC and insert the installer disc into

your PC’s CD-ROM drive.

2 The installation guide will appear automatically. If

it does not, go to the CD-ROM drive in Windows Explorer and double click the Setup.exe.

3 Select your desired language from the list. 4 Select install Software. 5 Connect the USB cable to the PC and Audio

System and press the USB PC Link button on the Audio set or the remote control.

6 Follow the instructions as prompted on the

screen to correctly install the USB PC Link Driver, Philips Sound Agent 2 and MusicMatch Jukebox software.

Notes: – Minimum OS requirement for Philips Sound

Agent 2: Windows 2000 or XP. – During installation, your previous MusicMatch Jukebox software on your PC will be replaced.

Declarations Windows and Pentium are trademarks of

Microsoft Corporation and Intel Corporation. All other trademarks belong to their respective owners. USB PC Link sample track, music by Chemistry (www.chemistryteam.com)

AUX/GAME

VOL

DSC WOOX LEVELVAC

USB PC LINK

USB PC Link

Using MusicMatch software

To create a music library

Add music files to My Music Library

Add files to My Library by dragging and dropping audio tracks from anywhere in Windows, into the My Library window.

You can also click Add Files in the Music Center to add tracks.

1 Click the Add Files button on the Music

Library window.

2 Browse your computer to the folder where

audio files are stored. Check the box Also Add Tracks from Subfolders to add all tracks in the

current folder, and all subfolders.

3 Click the Select All button to select all the files

in the current, and all subfolders.

4 Click Add.

Files will be added to My Library.

To create a “Playlist”

3 You will be prompted to name the Playlist. In

the Name field type the name you'd like to give this Playlist.

4 Click the Save button. Now you can play all the

saved playlists with the audio system by pressing

S or T buttons. Details operation, please

refer to Connecting to USB PC Link.

Note: – It is not possible to create a playlist from the system’s 5 CD changer. If you encounter any problem using USB PC Link, please refer to the FAQ (Frequently Asked Questions) stored in your USB PC Link installer disc or visit “www.audio.philips.com” for the latest update on FAQ.

Connecting to USB PC Link

USB PC Link allows you to playback your music collection from the PC via the powerful amplifier and speakers of this system.

IMPORTANT! Make sure the MUSICMATCH software has been installed. Refer to the CD-ROM sleeve for USB PC Link installation.

English

1 Drag and drop files, or folders with music files,

from anywhere on your computer or My Library into the Playlist window. Your files will

begin to play. Or, you may click the Open button on the Playlist window to browse for and add music to the Playlist.

2 Click the Save button on the Playlist, or go to

the menu Options>Playlist>Save Playlist.

1 Tu rn on your computer and launch the

“MUSICMATCH JUKEBOX”.

➜ The volume level of PC should not be put

into mute.

2 Press USB PC LINK.

➜ If the audio streaming is detected,

“CONNECTING” is displayed and the USB indicator will be flashing.

➜ If “ NO CONNECTION” is displayed, check the

connection between your PC and micro system.

USB PC Link

English

Notes: – When the USB PC Link feature is activated, Philips Sound Agent 2 will automatically be launched (if it has been successfully installed under OS Windows 2000/XP). – The default setting for PRESET/REVERB is MP3/ Study Room respectively. You may select from the list of different sound modes to suit your music and environment preference. Alternatively, you may select PRESET (Neutral mode) and REVERB (No Environment mode) for the minimum sound effect.

3 Press à or á to select your favorite playlist,

and then press í or ë until the desired track in the playlist is highlighted.

4 Press ÉÅ to star t playback.

➜ The track information will appear on the

display. The display only supports English characters.

During playback, – Press SHUFFLE to play all available tracks in the playlist in random order. – Press REPEAT to repeat playback of all the tracks in the playlist.

5 To exit, select another active mode or

press Ç.

Philips Sound Agent 2

Philips Sound Agent 2 is a BONUS software

provided with Philips Audio system to enhance the quality of MP3 Music playback via USB PC Link.

1 Philips Sound Agent 2 will be automatically

launched if USB PC Link is selected.

2 Press DSC/PRESET or VAC/REVERB to

select different Preset or Reverb sound effect.

3 For more details about using Philips Sound

Agent 2 features on your PC, please refer to

the User Manual in the supplied CD-ROM or the Help menu.

Notes: – Philips Sound Agent 2 minimum OS requirement: Windows 2000 or XP. – Please refer to the CD-ROM sleeve for detailed installation procedures, OR ‘Software installation’ in this manual.

Enabling digital CD audio output

Before playing the CD through your PC’s CD-ROM drive, it is necessary to configure your PC’s hardware as follows:

For Windows ME/ 2000 /XP

1 Enter the system control panel menu and

select: “System ™ Hardware ™ Device Manager ™ CD-ROM drives ™ Action-Properties ™ Properties ”.

For Windows 98SE

Enter the system control panel menu and select: “MULTIMEDIA” and “ CD MUSIC”.

2 Check the ‘Enable digital CD audio for this CD-

ROM device’ setting option is selected (enabled).

Notes: –You may need to refer to your PC’s manual for correct configuration. –For the optimal playback effect of the CD/MP3CD, please use your Philips audio system.

Basic Operations

Switching on/off

Switching to active mode

● Press CD, TUNER, USB PC LINK or

AUX•GAME.

Switching to Eco Power standby mode

● Press B.

➜ ECO POWER button lights up. ➜ The display screen will go blank.

Switching to standby mode (view clock)

● Press and hold B.

➜ The clock is displayed. ➜ While in the standby mode, pressing

CLOCK•TIMER button will switch the system to the Eco Power standby mode.

Note: – Before switching the system to the Eco Power standby or standby mode, make sure the demonstration mode has been deactivated.

Demonstration mode

If the demonstration mode is active, whenever you switch the system to the Eco Power standby or standby mode, it will show the various features offered by the system.

To activate the demonstration

● In the Eco Power standby/standby mode,

press and hold Ç on the main unit until “DEMO ON” is displayed.

To deactivate the demonstration

● Press and hold Ç on the main unit until

”DEMO OFF” is displayed.

Setting the clock

The clock can be set in either 12-hour or 24-hour mode (“11:59 PM” or “23:59” fo r example).

VOL

/ 12:00AM)

(00:

2 4

:00 / 12:00AM)

(

DSC WOOX LEVELVAC

(00:00 î 12:00AM)

1 Press and hold CLK/TIMER (or

CLOCK•TIMER on main unit) until “SELECT CLOCK OR TIMER” is displayed.

2 Press ë to change the display to “CLOCK” and

press CLK/TIMER (CLOCK•TIMER) again to confirm.

3 Press PROGRAM (PROG) repeatedly to

change between the 12-hour and 24-hour clock mode.

4 Press à or á repeatedly to set the hour. 5 Press í or ë repeatedly to set the minute. 6 Press CLK /TIMER (CLOCK•TIMER) to

store the setting.

➜ The clock will start working.

To view the clock time in any active mode

● Press CLK /TIMER (CLOCK•TIMER) once. ➜ The clock is displayed for a few seconds.

Notes: – The clock setting will be erased when the system is disconnected from the power supply. – The system will exit the clock setting mode if no button is pressed within 90 seconds. –To set the clock automatically through the time information in the RDS signal, refer to "Tuner Operations – Setting the RDS clock".

English

Basic Operations

English

Dimming system’s display screen

You can select the desired brightness for the display panel.

● In any active mode, press DIM on the remote

control or DIM MODE on the system repeatedly to turn on/off dim mode.

➜ DIM is shown, except for the DIM OFF mode.

Volume control

● Adjust MASTER VOLUME (or press

VOL +/- on

increase or decrease the sound level.

➜ “VOL MIN” is the minimum volume level and

”VOL MAX” is the maximum volume level.

To switch off the volume temporarily

● Press MUTE on the remote control. ➜ Playback will continue without sound and

“MUTE” is displayed.

➜ To restore the volume, press MUTE again or

increase the volume level.

the remote control) to

Incredible Surround

Incredible Surround magnifies the virtual distance between the front speakers for an incredibly wide, enveloping, stereo effect.

● Press INC SURR to turn on/ off the incredible

surround sound effect.

➜ If activated, IS will appear on the display.

Digital Sound Control

DSC provides a different type of preset sound equaliser setting.

● Press DSC repeatedly to select: OPTIMAL,

JAZZ, ROCK or POP.

Virtual Ambience Control

VAC provides a different type of environmentbased equaliser setting.

● Press VA C repeatedly to select : HALL,

CINEMA, CONCERT, CYBER or ARCADE.

Note: – When you select VAC, Incredible Surround will switch on automatically.

Sound control

DSC and VAC features cannot be activated at the same time. While in the game mode, all the sound control features are not available except wOOx and Game Sound control.

wOOx

The wOOx sound is designed to produce and handle high dynamic sound signals at very low frequencies.

● Press wOOx 1/2/3 respectively (or press

wOOx LEVEL repeatedly on remote control)

to select : wOOx 1, wOOx 2, wOOx 3 or wOOx OFF.

➜ Some discs might be recorded in high

modulation, which causes a distortion at high volume. If this occurs, deactivate wOOx or reduce the volume.

Automatic DSC-wOOx and VAC-wOOx selection

The best wOOx setting is generated automatically for each DSC, VAC, Game Sound selection. You can manually select the wOOx setting that best suits your listening environment.

Disc Operations

IMPORTANT! – This system is designed for regular discs. Therefore, do not use any accessories such as disc stabiliser rings or disc treatment sheets, etc., as offered on the market, because they may jam the changer mechanism. – Do not load more than one disc onto each tray.

Playable discs

This system is able to play: – All pre-recorded audio CDs – All finalised audio CDR and audio CDRW

discs

– MP3-CDs (CD-ROMs with MP3 tracks)

Loading discs (page 3 – P4)

1 Press OPEN • CLOSE 0 DISC 1 button on

top of the main unit to open disc tray 1.

2 Load a disc with the label side facing up. 3 Press OPEN • CLOSE 0 DISC 1 button again

to close the disc tray.

➜ “READING“ is displayed. The selected disc

tray, total number of tracks and the playing time will appear on the display.

4 Repeat steps 1~3 to load discs onto the disc

trays 2~5.

Basic playback controls

Load discs (page 3 – P4)

To play all discs on the disc trays

● Press ÉÅ.

In the stop mode, press CD to select a disc tray to begin, then press ÉÅ.

➜ All the available discs will play once, and then

stop.

To play the selected disc only

● Press one of the CD 1~5 buttons on remote. ➜ The selected disc will play once, and then

stop.

To select a desired track

● Press í or ë repeatedly until the desired

track is displayed.

➜ During random play (shuffle mode), pressing

í will not affect the current playback.

To search for a particular passage during playback

● Press and hold à or á and release it when

the desired passage is located.

➜ During searching, the volume will be reduced.

For MP3 disc, the volume will be muted.

To replace discs without interrupting playback

● Press OPEN•CLOSE 0 buttons of the

inactive disc trays (refer to “Loading discs”). For example, if currently disc tray 1 is playing, you can replace the discs on disc tray 2~5.

English

Notes: –To ensure good system performance, wait until the disc trays completely read the disc(s) before proceeding. – Only one tray can be opened each time. If you open the second tray before closing the first tray, the first tray will automatically close before the second tray opens.

To interrupt playback

● Press ÉÅ. ➜ To resume normal playback, repeat the

above.

To stop playback

● Press Ç. ➜ If the system remains in the stop mode for 30

minutes, it will switch to the Eco Power standby mode.

Disc Operations

English

Playing an MP3 disc

1 Load an MP3 disc.

➜ The disc reading time may exceed 10

seconds due to the large number of songs compiled in one disc.

➜ “AXX TYYY” is displayed. XX is the current

album number and YYY is the current title number.

2 Press à / á to select a desired album.

3 Press í / ë to select a desired title.

4 Press ÉÅ to star t playback.

● During playback, press DISPLAY to show the

album and title name.

Supported MP3 disc formats:

– ISO9660, Joliet, UDF 1.5 – Maximum title number : 999 (depending on

filename length) – Maximum album number : 99 – Supported sampling frequencies : 32 kHz,

44.1 kHz, 48 kHz

– Supported Bit-rates : 32~256 (kbps), variable

bitrates – ID3 tags : V1.1, V2.2, V2.3, V2.4

VOL

DSC WOOX LEVELVAC

Repeat and shuffle

You can select and change various play modes

TITLE

AUX/GAME

USB PC LINK

A02 T008

ALB

A02 T001

before or during playback.

Repeat play

1 Press REPEAT on the remote control

repeatedly to select :

A B C

D E

A – to repeat playback of the current track. B – to repeat playback of the current disc. C – to repeat playback of all available discs

(not available for this model).

D – to repeat playback of the current

programmed track (only if the programme mode is active)

E – to repeat playback of all the programmed

tracks (only if the programme mode is active)

2 To resume normal playback, press REPEAT

until “OFF” is displayed.

Random play

● Press SHUFFLE on the remote control to turn

on/off the shuffling mode.

➜ If activated, SHUF is shown and the repeat

mode (if any) will be cancelled.

➜ The random play will start from the current

disc tray. And it will change to the next available disc tray only after all the tracks in the active one have been shuffled.

➜ If the programming mode is active, only the

programmed tracks will be played in a random order.

Note: –Pressing the OPEN•CLOSE button will cancel all repeat and shuffling modes.

Disc Operations

Programming the disc tracks

Programming tracks is possible when playback is stopped. Up to 99 tracks can be stored in the memory in any order.

IMPORTANT! It is only possible to program from the current selected disc tray.

AUX/GAME

USB PC LINK

DSC WOOX LEVELVAC

VOL

1 Load the desired discs on the disc trays (refer to

“Loading discs”).

2 Press CD or one of the CD 1~5 buttons to

select a disc.

3 Press PROGRAM (PROG) to star t

programming.

➜ PROG starts flashing.

4 Press í or ë repeatedly to select the desired

track.

● For MP3 disc, press à / á and í / ë to

select the desired album and title for programming.

5 Press PROGRAM (PROG) to store.

● Repeat steps 4–5 to select other tracks. ➜ If you attempt to program more than 99

tracks, “PROGRAM FULL” is displayed.

6 To star t program play, press ÉÅ. 7 To stop playback or to end programming, press

Ç once.

➜ PROG stays and the programming mode

remains active.

Notes: – If the total playing time has reached 100 minutes or one of the programmed tracks has a number greater than 30, “—:—” is displayed instead of the total playing time. – The system will exit the programming mode if no button is pressed within 20 seconds.

Checking the programme

1 Stop playback and press í or ë repeatedly. 2 Press Ç to exit.

Press ÉÅ to start playback from the current programmed track

Clearing the programme

● Stop playback, and then press Ç to clear the

programme.

Press the OPEN•CLOSE 0 button of the disc tray.

➜ PROG disappears and “PROGRAM CLEARED”

is displayed.

Note: – The program will be erased if the system is disconnected from the power supply or you switch to another source mode.

English

Tuner Operations

English

IMPORTANT! Make sure the FM and MW antennas are connected.

Tuning to radio stations

1 Press TUNER to enter tuner mode.

To select another waveband (FM or MW), press TUNER again.

2 Press and hold à or á until the frequency

indication starts to change, then release.

➜ The system automatically tunes to the next

strong signal radio reception.

➜ lights up for FM stereo reception. ➜ RDS lights up for RDS station (in FM band

only).

Tuning to a weak signal station,

● Press à or á briefly and repeatedly until an

optimal reception is found.

Presetting radio stations

You can store up to 40 preset radio stations in the memory, starting from FM and followed by MW bands.

Notes: – The system will exit presetting mode if no button is pressed within 20 seconds. – If no stereo frequency is detected during Plug and Play, “CHECK ANTENNA” is displayed.

Using the plug and play (page 3 - P3)

Plug and Play allows you to store all available radio stations automatically.

1 Connect the system to the power supply,

“AUTO INSTALL - PRESS PLAY” is displayed.

In the Eco Power standby/standby mode,

press and hold ÉÅ on the main unit until “AUTO INSTALL - PRESS PLAY” is displayed.

2 Press ÉÅ on the main unit to star t installation.

➜ “INSTALL TUNER” is displayed. ➜ All previously stored radio stations will be

replaced.

➜ Once completed, the last tuned radio station

will be played.

➜ Once completed, the last tuned radio station

(or the first available RDS station) will be played.

3 If the first preset is a RDS station, it will

proceed to set the RDS clock.

➜ "INSTALL" is displayed, followed by "TIME"

and "SEARCH RDS TIME".

➜ When RDS time is read, "RDS TIME" is

displayed and the current time will be stored.

➜ If RDS station does not transmit RDS time

within 90 seconds, “NO RDS TIME” is displayed and the programme will exit automatically.

Automatic presetting

You can start the automatic presetting from a selected preset number.

1 In the tuner mode, press í or ë to select a

preset number.

2 Press and hold PROGRAM (PROG) until

“AUTO” is displayed.

➜ If a radio station has been stored in one of

the presets, it will not be stored again at another preset number.

➜ If no preset number is selected, automatic

preset will begin from preset (1) and all your previous presets will be overridden.

Manual presetting

You can choose to store only the favourite radio stations.

1 Tune to your desired radio station (refer to

“Tuning to radio stations”).

2 Press PROGRAM (PROG).

➜ The preset number starts flashing. If you want

to store the radio station in another preset number, press í or ë.

3 Press PROGRAM (PROG) again to store.

● Repeat steps 1–3 to store other radio stations.

Tuner Operations

Selecting a preset radio station

● In the tuner mode, press í or ë.

➜ The preset number, radio frequency, and

waveband are displayed.

Deleting a preset radio station

● Press and hold Ç until “PRESET DELETED” is

displayed.

➜ The current preset radio station will be

deleted.

➜ All other preset radio stations with higher

numbers are decreased by one.

RDS

RDS (Radio Data System) is a service that allows FM stations to show additional information. If you are receiving a RDS station,

RDS and the station name are displayed.

Scrolling through RDS information

● Tuned to a RDS radio station from FM band,

then press NEWS•RDS repeatedly to select the following information (if available): – Station name – Programme type (for example: News, Affairs,

Sport, etc.) – Radio text messages – Frequency

Setting the RDS clock

Some RDS radio station may be transmitting a real clock time at an interval of ever y minute. It is possible to set the clock by using a time signal which is broadcast together with the RDS signal.

1 Tuned to a RDS station from FM band (refer to

“Tuning to radio stations”).

2 Press and hold CLOCK•TIMER on the main

unit until "SELECT CLOCK OR TIMER" is displayed. Then press ë to change the display to “CLOCK” and press CLOCK•TIMER again to confirm.

3 Press NEWS•RDS.

➜ "SEARCH RDS TIME" is displayed. ➜ When RDS time is read, the current time will

be stored.

➜ If the RDS station does not transmit RDS

time within 90 seconds, "NO RDS TIME" is displayed.

English

Note: – Some RDS radio station may be transmitting a real time clock at a minute interval. The accuracy of the transmitted time depends on the transmitting RDS radio station.

Tuner Operations

English

NEWS

You may set up the tuner in such a way that listening to CD or external source is interrupted by the NEWS of a RDS station. This only works if the RDS station broadcasts a NEWS signal while sending the news.

IMPORTANT! You can activate NEWS function from any source mode except TUNER.

Switching on NEWS function

1 In any active mode, press and hold

NEWS•RDS until "NEWS" is displayed.

➜ NEWS is shown. ➜ The system will scan the radio stations stored

in the first five (5) preset and wait for the News Programme Type data to be available in any of these RDS stations.

➜ While searching NEWS in progress, the

current active mode remains uninterrupted.

2 When NEWS transmission is detected, the

system will switch to Tuner mode.

➜ NEWS starts flashing.

● If no RDS station is detected in the first five

presets, the system will exit NEWS function.

➜ "NO RDS NEWS" is displayed.

Notes: –You have to exit Tuner mode before selecting NEWS function. – Before you activate the NEWS feature, ensure that the first five presets have RDS stations. – The NEWS works only once for each activation.

To cancel NEWS function

● Press and hold NEWS•RDS again or switch

the system to tuner mode.

During news bulletin, press any other available source keys to execute the relevant source mode.

Timer Operations

Timer setting

The system can switch on to CD, TUNER or USB PC LINK mode automatically at a preset time, serving as an alarm to wake you up.

IMPORTANT! – Before setting the timer, ensure that the clock is set correctly. – The volume of the timer will increase gradually to the last tuned volume level. If the last tuned volume level is too low, the set will then increase to a predetermined minimum audible level.

(CD / TUNER / USB PC LINK)

(00:

/ 12:00AM)

2 4

(00:00 / 12:00AM)

1 Press and hold CLK / TIMER (or

CLOCK•TIMER on main unit) until “SELECT CLOCK OR TIMER” is displayed.

2 Press ë to change the display to “TIMER” and

press CLK/TIMER again to confirm.

3 Press CD or TUNER or USB PC LINK to

select the wake-up source.

➜ The selected source will be lighted while

other available sources are flashing.

4 Press à or á (for hours) and í or ë (for

minutes) repeatedly to set the wake-up time.

5 Press CLK / TIMER to store the setting.

➜ The timer will always be switched on once it

has been set.

➜ icon remains on the display. It indicates the

timer is activated.

● At the preset time, the selected sound

source will be played for 30 minutes before it switches to Eco Power standby mode (if no button is being pressed within the

time frame).

➜ CD – playing the first track of the last

selected disc. If the last selected disc tray is empty, it will switch to the next available disc. If all the disc trays are not available, it will switch to Tuner mode.

➜ TUNER – playing the last tuned radio station. ➜ USB PC LINK – playing the last selected

playlist. If the connection fails, it will switch to Tuner mode. Refer to “USB PC Link” for proper connection and setup before use.

Activating/deactivating the timer

● Press TIMER ON / OFF on the remote control

to turn off the timer or turn on to the last setting again.

➜ If activated, the timer information will display

for a few seconds, then the system resumes to the last active source or stays in the standby mode.

➜ If deactivated, “CANCEL” is displayed.

Notes: – The system will exit the timer setting mode if no button is pressed within 90 seconds. – The USB timer does not function when the computer is in the standby mode.

English

Timer Operations Other Connection

English

Sleep timer setting

The sleep timer enables the system to switch to the Eco Power standby mode automatically at a preset time.

1 Press SLEEP repeatedly until it reaches the

desired preset turn-off time.

➜ The selections are as follows (time in

minutes):

15 ™ 30 ™ 45 ™ 60 ™ 90 ™ 120 ™ OFF ™ 15 …

➜ SLEEP is shown, except for the “OFF” mode. ➜ To view or change the setting, repeat the

above.

2 Before the system switches to the Eco Power

standby mode, a countdown of 10 seconds is displayed.

“SLEEP 10” ™ “SLEEP 9”.... ™ “SLEEP

1” ™ “SLEEP”

To cancel the sleep timer function

● Press SLEEP repeatedly until “OFF” is

displayed, or press the STANDBY ON B button.

Listening to an external device

You can listen to the sound of the connected external device through your system’s speakers.

AUDIO OUT

1 Use the red / white audio cables to connect the

system’s AUX IN (R / L) terminals to the AUDIO OUT terminals on another audio/visual device (such as a TV, VCR, Laser Disc player, DVD player or CD recorder).

2 Press AUX/GAME until “AUX” is displayed. 3 Press PLAY on the connected device to start

playback.

AUX

LINE OUT

AUX IN

Listening to an external device

AUDIO I N

● Use the red/white audio cables to connect

the system’s LINE OUT (R/L) terminals to the AUDIO IN terminals on a recording device (such as CD/Tape recorder).

Notes: – All the sound control features (DSC, VAC for example) are available for selection. – Always refer to the owner’s manual of the other equipment for complete connection and use details.

LINE OUT

AUX IN

Specifications

AMPLIFIER

Output power ........................................ 8500 W MPO

................................................................. 2 x 200 W RMS

Booster .................................................................. 2x100 W

Signal-to-noise ratio ....................................... ≥ 62 dBA

Frequency response ........ 63 – 16000 Hz, ≤–3 dB

Input sensitivity

AUX In ................................................................................... 640 m V

Gameport .............................................................................. 640 mV

Output

Speakers ..................................................................................... ≥ 6 Ω

Booster Speakers .................................................................. ≥ 6 Ω

Headphones ........................................................ 32 Ω – 1000 Ω

(1)

(6 Ω, 60Hz - 12.5 kHz, 10% THD)

DISC PLAYER

Programmable tracks .................................................... 99

Frequency response ........... 50 – 18000 Hz, –3 dB

Signal-to-noise ratio ........................................ ≥ 62 dBA

Channel separation .......................... ≥ 35 dB (1 kHz)

MPEG 1 Layer 3 (MP3-CD) .......... MPEG AUDIO

MP3-CD bit rate ....................................... 32-256 kbps

.................................................................... (128 kbps advised)

Sampling frequencies ....................... 32, 44.1, 48 kHz

USB

Frequency response ...... 50 – 18000 Hz, ≤ ±3 dB

Signal-to-noise ratio .......................................... ≥ 62 dBA

Channel separation .............................. ≥ 35 dB (1 kHz)

Total harmonic distortion ............... < 0.3% (1 kHz)

TUNER

FM wave range ...................................87.5 – 108 MHz

MW wave range ................................ 531 – 1602 kHz

Number of presets ........................................................ 40

Antenna

FM ......................................................................................... 75 Ω wire

MW .............................................................................. Loop antenna

SPEAKERS

(1)

System ...................................................3 way, Bass reflex

Impedance ......................................................................... 8 Ω

English

Woofer ...................................................................... 1 x 6.5"

Tw eeter................................. 1 x 2" Ferro fluid cooled

Dimensions (w x h x d) .. 348 x 322 x 245(mm)

Weight............................................................. 4.35 kg each

BOOSTER SPEAKERS

System .......................................................................... 3-way

Impedance ........................................................................ 6 Ω

Woofer .......................................................................... 2 x 4"

Tw eeter.......................................................................... 1 x 2"

Dimensions (w x h x d) ....................................................

...................................................... 140 x 310 x 310 (mm)

Weight................................................................ 4.0 kg each

GENERAL

Material/finish ................................... Polystyrene/Metal

AC Power ..................................... 220 – 230 V / 50 Hz

Power Consumption

Active ........................................................................................ 130 W

Standby .................................................................................. < 25 W

Eco Power Standby ............................................................. < 1 W

Dimensions (w x h x d) . 265 x 322 x 390 (mm)

Weight (without speakers)................................. 8.6 kg

BOOSTER UNIT

Material/finish ................... Polystyrene/Metal/Wood

AC Power ............................ 110 – 127 / 220 – 240 V;

....................................................... 50/60 Hz Switchable

Power Consumption

Active ...................................................................... 150 W

Standby ..................................................................... 25 W

Dimensions (w x h x d) .....................................................

...................................................... 140 x 310 x 345 (mm)

Weight (without speakers) .................................. 7.0 kg

Specifications and external appearance are subject to change without notice.

Tr oubleshooting

English

WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock.

If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help.

Problem

Auto Installation of the Installer CD-ROM did not install the Philips Sound Agent 2 onto my PC.

When in USB PC LINK mode, “NO CONNECTION” is displayed.

I want the minimum effect from the Philips Sound Agent 2 sound mode when listening to MP3 music streaming via USB PC Link.

Radio reception is poor.

“NO DISC” is displayed or the disc cannot be played.

The system does not react when buttons are pressed.

Sound cannot be heard or is of poor quality.

Solution

✔ Check that your PC’s Operating System is running on

Windows 2000/XP.

✔ Check the connection between your PC and the

system and the inital setup required, see “Connections” and “USB PC Link”.

✔ Make sure the connected PC is turned on.

✔ Select the PRESET - Neutral mode. ✔ Select the REVERB - No environment mode.

✔ If the signal is too weak, adjust the antenna or connect

an external antenna for better reception.

✔ Increase the distance between the system and your TV

or VCR.

✔ Insert a disc. ✔ Load in the disc with label facing right. ✔ Replace or clean the disc, see “Care and safety

information”.

✔ Use a finalised CD-R(W) or a correct format disc.

✔ Remove and reconnect the AC power cord and switch

on the system again.

✔ Adjust the volume. ✔ Disconnect the headphones. ✔ Check that the speakers are connected correctly. ✔ Check that the AC power cord is connected properly. ✔ When in USB PC LINK mode, check that the PC’s

volume is not put into mute.

✔ When playing CD from PC’s CD drive, refer to “USB

PC Link - Enable digital CD audio output“.

Refer to the FAQ (Frequently Asked Questions) on the supplied CD-ROM or visit our website

“www.audio.philips.com” for latest update on FAQ.

Tr oubleshooting

Problem

The remote control does not function properly.

The timer is not working.

The system displays features automatically and buttons start flashing.

“UACB error” and “Audio Set is not connected/nor filter driver is not loaded” message prompts up on Computer screen in Windows XP.

Solution

✔ Select the source (CD or TUNER, for example) before

pressing the function button (ÉÅ, S ,

✔ Reduce the distance between the remote control and

the system.

✔ Replace the battery. ✔ Point the remote control directly toward the IR sensor.

✔ Set the clock correctly. ✔ Press TIMER ON/OFF to switch on the timer.

✔ Press and hold DEMO STOP on the main unit to switch

off the demonstration mode.

✔ Reboot the computer.

T).

English

Refer to the FAQ (Frequently Asked Questions) on the supplied CD-ROM or visit our website

“www.audio.philips.com” for latest update on FAQ.

Philips FWM799/22, FWM799/21 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual