Universe Vacuum cleaner
FC9014
/A
/B
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
- Colour /A : Pistache
/B : Crystal white
- Maximum air displacement : 37 l/sec.
- Maximum vacuum water column : 310 cm
- Power consumption (IEC) 230 V : 1500 W
- Duststorage capacity : 3 L
- Type number dustbag : FC8021
- Cord length (depends on version) : 7 metres
- Filter system : Paper dustbag
: Exhaust AFS air filter
: Motor inlet filter
- Dimensions of cleaner : 460 x 315 x 270 mm
- Dimensions of packaging : 595 x 395 x 295 mm
- Net weight : 5.88 kg
- Gross weight : 9.135 kg
OPTIONAL (accessories)
- FC8021 S-bags
- FC8030 AFS-filter
- FC8031 HEPA Air Filter
- FC8034 Upgrate kit Active Carbon Filter
- FC8042 Polishing nozzle
- FC8043 Turbo brush nozzle
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- Open the appliance, first remove the exhaust filter grille
(item 20), and then remove the 2 screws - C of the switch
control panel (item 15).
C 2x
C 9x
- To remove the the panel, pos 14a + b must be removed by
using a screwdriver to separate the two covers from the panel
as shown in the picture.
- Undo and remove the 9 screws (T15) - C in the upper
housing (item 8). You will require a screwdriver with a
14.5 cm-long shank for this. Srewdriver 4322 009 08490
can be used.
- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.
- When the repair is finished, check whether all functions of
the appliance work properly.
- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10; T9;
T8; T7 and T6 (code number 4822 395 50145).
14a + b
= changed
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
03/07
REPAIR INSTRUCTION
- Item 4, cotton dustbag, is used in countries in which paper
dustbags are not available.
- If the reel half spring unit is replaced, shaft A must be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (43) or conductors
(42).
- Item 40 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)
- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn
- Item 13, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.
- If the function of the electronic control unit (item 12) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, eventhough the dustbag is not
full at all.
FC9014 /A /B
- Due to introduction of a new switch (item 11) 0320
onwards, which is not interchangable with the old switch
soldered on the PCB (item 12).
- The switch lever assy (item 11a) is also modified.
To recognize the switches:
Old New
∅ 13 mm
New spares are:
Switch soldered version - 4322 006 50600
Switch lever assy - 4322 009 08980
∅ 10 mm
= changed
ELECTRICAL DIAGRAM
MOTOR
POWER
MODULE
Black
Black
Blue
Brown
M
CORD WINDER
Triac
Short-circuit
2-6
PARTS LIST
FC9014 /A /B
Pos Service code Description
1
4322 005 14490
4322 005 14530
2
4322 003 21620
3
4322 003 21730
4
8838 021 00000
4322 004 93290
5
4322 003 18300
6
4322 001 73310
7
4322 005 12550
8
4322 003 21610
8a
4322 003 21740
9
4322 000 37300
10
4322 009 07040
11
4322 006 21480
4322 006 50600
11a
4322 009 08420
4322 009 08980
12
4322 006 22560
13a
4322 005 12200
13b
4322 005 12210
14a
4322 003 21710
14b
4322 003 21700
15
4322 009 08600
4322 009 08640
16
4322 003 21600
18
4322 000 37450
19
4322 005 12190
20
4322 009 08590
21
22
4322 004 92910
23
4322 001 73280
24
4322 003 18000
25
4322 000 37420
26
4322 000 37430
27
4322 003 21660
28
4322 003 18910
29
not available
Dust cover Pistache /A
Dust cover Crystal white /B
Dust cover lock c.grey
Dustbag holder s.grey
S-paper dustbags FC8021
Cotton dustbag
Cordwinder lever
Sealing rim
Dustbag detector
Upper housing c.grey
Clamp upper/lower housing
Triple fi lter
Grill + triple fi lter
Switch soldered version
Switch sold. vers. 0320 onwards
Switch lever assy
Switch lever assy 0320 onwards
PCB slide turn 230V
Dustbag full indicator
Air valve
Cover R c.grey
Cover L c.grey
Panel assy turn Pistache /A
Panel assy turn Crystal white /B
Lower housing c.grey
Silencer 4 wall
Caster assy m.grey
Exhaust grille c.grey
Electr.static fi lter FC8030
Filter sealing
S-class sealing
Silencer 1 wall
Silencer 2 bottom
Cord outlet c.grey
Rear wheel lock red
Receipt. housing A.C.
Pos Service code Description
30
4322 003 21690
31
4322 001 73300
32
4322 003 18040
33
4322 003 18010
34
4322 003 18020
35
4322 001 73290
36
4322 009 06430
37
4322 000 37440
38
4322 003 18030
40
4322 009 07940
41
4322 001 72360
42
4322 009 07950
43
4322 009 07970
44
4322 006 01440
4322 006 01760
45
4322 006 01680
46
4322 006 01720
47
4322 006 01410
48
4322 006 01670
49
4322 006 01460
50
4322 003 20420
51
4322 005 13400
55
4322 004 21170
56
4322 003 20100
57
4322 005 13520
58
4322 002 22610
59
4322 004 22990
62
4322 004 22880
63
4322 004 22940
A
5322 390 20011
B
4322 002 82550
C
2522 200 02018
Rear wheel c.grey
Motor buffer back
Inlet sealing
Motor cap top
ANS disc
Motor bufferring front
Motor A 1441 230V
Silencer 3 ans
Motor cap bottom
Reel half spring unit (L = 9m)
Brake tyre
Reel half contact unit
Contact ring plate
Argentina L = 9.3 m
Australia L = 9.3 m
Taiwan L = 6.3 m
U.K. / H.K. L = 9.3 m
Euro 4.8 mm pins L = 9.3 m
Swiss L = 9.3 m
Italy L = 9.3 m
C-bend B1
C-bend B1 hose assy
Plumeau assy (opt.)
Crevice nozzle con.
Acc. bridge assy
Metal tube con.
Telesc. tube con. (opt.)
Small nozzle con.
Nozzle RD262 con.
Silicon grease for shaft
Screw 3.5 x 12 T10
Screw 3.5 x 19 T15
= changed
3-6
EXPLODED VIEW
FC9014 /A /B
14a
1
2
3
4
14b
15
9
10
11a
11
12
20
5
8a
6
7
8
C
Z
Y
13a
13b
22
23
18
4-6
EXPLODED VIEW
40
41
FC9014 /A /B
B
42
A
44÷49
B
43
16
24
25
26
27
brownblue
Z
32
33
34
35
28
black
36
Y
29
19
31
30
37
38
5-6
EXPLODED VIEW
Argentina
Australia
44
FC9014 /A /B
Europe Ø 4.8mm 47
51
50
Taiwan 45
46U.K. / H.K.
Swiss 48
Italy 49
62
55
56
57
58
59
63
6-6
Loading...