Philips DVD-620 Service manual

DVD-Video Player DVD620-623-633

DVD620 /001 /021 /051 DVD623 /001 /021 /051 DVD633 /001 /021 /051

Contents Page

1 Technical Specs and Connection Facilities 2 2 Safety Instructions, Warnings, Notes,

and Service Hints 3 3 Directions for Use 6 4 Mechanical- and Dismantling Instructions 16 5 Diagnostic Software, Trouble Shooting and Test

Instructions 18 6 Wiring-, Block Diagrams

Block Diagram 37

Wiring Diagram 38 7 Electrical Diagrams and Print-Layouts Diagram PWB

Power Supply Unit 39 40

AV Board: Video & SCART (Diagram A1) 41 45-51

AV Board: Audio (Diagram A2) 42 45-51

AV Board: Front (Diagram A3) 43 45-51

AV Board: Regulated Supply (Diagram A4) 44 45-51

Front Controls (Diagram C) 52 52

Front Standby-On (Diagram S) 52 52 8 Alignments (Not Applicable)53 9 Circuit-, IC Descriptions, and 53

List of Abbreviations 56 10 Spare Parts List 58

CL 16532162_000.eps

070102

Copyright 2002 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

Published by MW 0261 Service PaCE Printed in the Netherlands Subject to modification EN 3122 785 12210

EN 2 DVD 620 /0X11.

Technical Specifications & Connection Facilities

1. Technical Specifications & Connection Facilities

Specifications

PLAYBACK SYSTEM

DVD Video Video CD & SVCD CD (CD-Recordable and CD-Rewritable)

TV STANDARD (PAL/50Hz) (NTSC/60Hz)

Number of lines 625 525 Playback Multistandard (PAL/NTSC)

VIDEO PERFORMANCE

Video output 1 Vpp into 75 ohm RGB (SCART) output 0.7 Vpp into 75 ohm Black Level Shift On/Off Video Shift Left/Right

AUDIO FORMAT

Digital MPEG Compressed

Digital Dolby Digital 16, 20, 24 bits PCM fs, 44.1, 48 kHz

Analogue Stereo Sound Dolby Surround-compatible downmix from Dolby Digital multi-channel sound 3D Sound for virtual 5.1 channel sound on 2 speakers

AUDIO PERFORMANCE

DA Converter 24 bits DVD fs 96 kHz 4 Hz - 22 kHz

fs 48 kHz 4 Hz - 22 kHz CD/VCD fs 44.1 kHz 4 Hz - 20 kHz SVCD fs 48 kHz 4 Hz - 22 kHz

fs 44.1 kHz 4 Hz - 20 kHz Signal-Noise (1kHz) 110 dB Dynamic Range (1kHz) 95 dB Crosstalk (1kHz) 110 dB Distortion and Noise (1kHz) 90 dB

CONNECTIONS

SCART Euroconnector Video Output Cinch (yellow) Audio L+R output Cinch (white/red) Digital Output 1 coaxial

IEC958 for CDDA / LPCM IEC1937 for MPEG1/2 / Dolby Digital

CABINET

Dimensions (w x h x d) 435 x 75 x 210.5 mm Weight Approximately 1.9 Kg

* typical playing time for movie with 2 spoken languages and 3 subtitle languages

Specifications subject to change without prior notice

Cleaning the Cabinet

¶ Use a soft cloth slightly moistened with a mild

detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.

Cleaning Discs

¶ When a disc becomes dirty, clean it with a

cleaning cloth. Wipe the disc from the centre out. Do not wipe in a circular motion.

¶ Do not use solvents such as benzine, thinner,

commercially available cleaners, or antistatic spray intended for analogue records.

Maintenance

Cleaning the disc lens

¶ After prolonged use, dirt or dust may

accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with the cleaner.

CL 16532162_020.pdf

070102

Safety Instructions, Warnings, Notes, and Service Hints

2. Safety Instructions, Warnings, Notes, and Service Hints

EN 3DVD 620 /0X1 2.

2.1 Safety Instructions

2.1.1 General Safety

Safety regulations require that during a repair:

• Connect the unit to the mains via an isolation transformer.

• Replace safety components, indicated by the symbol ,

only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.

Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points:

• Route the wires/cables correctly, and fix them with the mounted cable clamps.

• Check the insulation of the mains lead for external damage.

• Check the electrical DC resistance between the mains plug and the secondary side:

1. Unplug the mains cord, and connect a wire between

the two pins of the mains plug.

2. Set the mains switch to the 'on' position (keep the

mains cord unplugged!).

3. Measure the resistance value between the mains plug

and the front panel, controls, and chassis bottom.

4. Repair or correct unit when the resistance

measurement is less than 1 MΩ.

5. Verify this, before you return the unit to the customer/

user (ref. UL-standard no. 1492).

6. Switch the unit ‘off’, and remove the wire between the

two pins of the mains plug.

2.1.2 Laser Safety

This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury).

2.2 Warnings

2.2.1 General

• All ICs and many other semiconductors are susceptible to

electrostatic discharges (ESD, "). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: – Complete kit ESD3 (small tablemat, wristband,

connection box, extension cable and earth cable) 4822 310 10671.

– Wristband tester 4822 344 13999.

• Be careful during measurements in the live voltage section.

The primary side of the power supply (pos. 1005), including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is 'off'!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A 'lightning stroke' and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply.

• Never replace modules, or components, while the unit is ‘on’.

2.2.2 Laser

• The use of optical instruments with this product, will increase eye hazard.

• Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury.

• Repair handling should take place as much as possible with a disc loaded inside the player.

• Text below is placed inside the unit, on the laser cover shield:

Laser Device Unit

Type : Semiconductor laser

GaAlAs

Wavelength : 650 nm (DVD)

: 780 nm (VCD/CD)

Output Power : 20 mW

(DVD+RW writing)

:0.8 mW

(DVD reading)

:0.3 mW

(VCD/CD reading)

Beam divergence : 60 degree

Figure 2-1

Note: Use of controls or adjustments or performance of

procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.

CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYONNE MENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU

Figure 2-2

2.2.3 Notes

Dolby

Manufactered under licence from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby

Figure 2-3

Trusurround

TRUSURROUND, SRS and symbol (fig 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.

Figure 2-4

EN 4 DVD 620 /0X12.

Safety Instructions, Warnings, Notes, and Service Hints

2.3 Service Hints

2.3.1 Switched Mode Power Supply

This power supply unit has to be repaired down to component level in case of failure.

2.3.2 DVD Module

This module can be repaired as follows:

1. The VAL6013/01 is a combination of loading mechanism and DVD-mechanism. Both are not repairable units and in case of failure, it has to be replaced with a new loader VAL6013/01.

Note: When replacing with a new VAL6013/01 and DVD mechanism, two solder joints have to be removed after connecting the OPU flex foil to the mono board. The solder joints, which shortcircuits the laser diodes to ground, are for protection against ESD. Refer to figures 25 and 2-6 for location of solder joints.

2. The mono board has to be repaired down to component level. Repair handling of the monoboard requires a workshop with sophisticated desoldering tools.

VAL6013/01 Solder Joints

2.3.3 ComPair

For assistance with the repair process of the monoboard an electronic fault finding guidance has been developed. This program is called ComPair. This ComPair program is available on CDROM. The version of the CDROM for repair of the monoboard is V1.3 or higher and can be ordered with codenumber 4822 727

21637. This is an update CDROM, so when the ComPair CDROM is used for the first time, one has to install the ComPair Engine CDROM V1.2 first. The V1.2 CDROM can be ordered with code number 4822 727 21634 and has to registered after instalation. The procedure for registration is explained in the help file of the program and in the CDROM booklet. The cable to connect the monoboard with a PC can be ordered with codenumber: 3122 785 90017. All the hardware and software requirements of the systems, necessary for working with ComPair, are described on the CDROM.

2.3.4 Service Positions

Refer to dismantling instructions for dismounting of the board. Figures 2-7 to 2-9 shows the service position that are recommended during repair of the boards.

Mono Board

Figure 2-5

VAL6013/01 Solder Joints

Figure 2-6

Figure 2-7

Mono Board

Figure 2-8

Mother Board

Safety Instructions, Warnings, Notes, and Service Hints

Figure 2-9

EN 5DVD 620 /0X1 2.

EN 6 DVD 620 /0X13.

3. Directions for Use

English

Contents

Access Control

Access Control: Child Lock ---------------------- 21

Access Control: Parental Control ---------- 21-22

Specifications

Specifications --------------------------------------- 23

Maintenance

Maintenance ---------------------------------------- 23

Troubleshooting

Directions for Use

Troubleshooting------------------------------------ 24

Introduction

Environmental Information ------------------------ 6

Supplied accessories -------------------------------- 6

Safety Information ----------------------------------- 6

Laser safety

This unit employs a laser. Due to possible eye

injury, only a qualified service person should

Symbols Used in this Manual ---------------------- 6

remove the cover or attempt to service this

device.

Functional Overview

Front and Rear Panels ------------------------------ 7

Remote Control ------------------------------------- 8

Preparation

USE OF CONTROLS, ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN

HAZARDOUS RADIATION

Basic Connections -----------------------------------9

Connecting to a TV---------------------------------- 9

Connecting to an Audio System ------------------ 9

Connecting to Optional Equipment ------------ 10

EXPOSURE.

NOTE:

PICTURES SHOWN MAY BE

Inserting batteries into the Remote Control - 10

NTSC/PAL Conversion --------------------------- 11

Switching On --------------------------------------- 11

Menu Bars on TV Screen ------------------------- 11

Personal Preferences -------------------------- 12-14

Operation

Basic Playback -------------------------------------- 15

Playing a DVD-Video ------------------------------ 15

Playing a Video CD -------------------------------- 16

Playing an Audio CD ------------------------------ 16

Special DVD features ------------------------- 16-17

Special VCD & SVCD Features ------------------ 17

780 nm (VCD/CD)

10 mW (VCD/CD)

DIFFERENT BETWEEN COUNTRIES.

LASER

Type Semiconductor laser GaAlAs

Wave length 650 nm (DVD)

Output Power 7 mW (DVD)

Beam divergence 60 degree

General Features ------------------------------ 17-20

CAUTION

(WARNING LOCATION: ON THE

BACKPLATE OF SET)

NEVER MAKE OR CHANGE

CONNECTIONS WITH THE POWER

SWITCHED ON.

symbol are

The region code for this set is 2.

Since it is usual for DVD movies to be released

at different times in different regions of the

world, all players have region codes and discs can

have an optional region code. If you load a disc

General Information

of a different region code to your player, you will

see the region code notice on the screen. The

disc will not play, and should be unloaded.

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories.

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual

property rights owned by Macrovision

Corporation and other rights owners. Use of this

authorised by Macrovision Corporation, and is

intended for home and other limited viewing

uses only unless otherwise authorised by

Macrovision Corporation. Reverse engineering or

TruSurround and the

trademarks of SRS Labs, Inc. TruSurround

disassembly is prohibited.

technology is incorporated under license from

The DVD VIDEO player is in

conformity with the EMC directive and

low-voltage directive.

For Customer Use:

Read carefully the information located at the

bottom of your DVD VIDEO player and enter

below the Serial No.Retain this information for

future reference.

Model No. DVD VIDEO

SRS Labs, Inc.

Serial No. __________________________

Directions for Use

English

Functional Overview

Front and Rear Panels

STOP PLAY/PAUSE

OPEN/CLOSE

STANDBY-ON

DVD623

DVD VIDEO PLAYER

STANDBY-ON

– to switch the player to standby mode orONDisc Tray

B; PLAY/PAUSE

– to start/interrupt playback

9 STOP

– to stop playback

/ OPEN/CLOSE

– to open/close the disc tray

COAXIAL

DIGITAL AUDIO OUT

PCM-MPEG2-Dolby Digital

TV OUT

(CVBS)

VIDEO OUT

AUDIO OUT

COAXIAL (Digital audio out)

– connect to AUDIO inputs of a digital

(coaxial) audio equipment

TV OUT VIDEO OUT

– connect to a TV with SCART

MAINS (AC Power Cord)

– connect to a standard AC outlet

CVBS VIDEO OUT

– connect to CVBS Video inputs of a TV

AUDIO OUT (Left/Right)

– connect to AUDIO inputs of an

amplifier, receiver or stereo system

Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic

discharge may cause permanent damage to the unit.

EN 7DVD 620 /0X1 3.

Introduction

space all around the player for adequate

ventilation.

● In cabinet, allow about 2.5cm (1 inch) of free

temperature or humidity.

to a warm location, or is placed in a very damp

room, moisture may condense on the lens of the

● Do not expose your player to extreme of

● If the DVD player is brought directly from a cold

disc unit inside the DVD player. Should this occur,

the DVD player would not operate normally.

Thank you for purchasing this Philips DVD player.

This Owner’s Manual explains the basic

operation of this DVD player.

Environmental Information

All unnecessary packaging has been omitted. We

have tried to make the packaging easy to

separate into three materials: cardboard (box),

polystyrene foam (buffer) and polyethylene (bags,

English

Leave the power on for about one hour with no

disc in the DVD player until normal playback is

possible.

lubricating bearings and must not be oiled or

lubricated.

Standby mode, it is still consuming some

● The mechanical parts of the set contain self-

● When the DVD player is switched to

protective foam sheet).

Your DVD player consists of materials which can

be recycled and reused if disassembled by a

specialised company. Please obser ve the local

regulations regarding the disposal of packaging

materials, exhausted batteries and old

equipment.

Symbols Used in this Manual

The below symbols appear in some headings

power. To disconnect the system from

the power supply completely, remove the

AC power plug from the wall socket.

and notes with the following meanings:

Supplied accessories

– Remote control

– Batteries (two AA size) for remote control

– Audio cable

– SCART cable (not available for all versions)

– Owner’s Manual

– Description refers to playback of Video CDs

– Description refers to playback of DVD-video discs

DVD

Safety Information

– Description refers to playback of Audio CDs

VCD

Some DVD video discs require specific

Helpful Hints!

●

operating voltage indicated on the typeplate (or

the voltage indication beside the voltage

selector) is identical with the voltage of your

local power supply. If not, please consult your

dealer.

● Before operating the DVD player, check that the

● Place the DVD player on a flat, hard and stable

“ Ä“ may appears on the TV screen

functions or allow only limited functions

during playback.

which means that the function is not

available on that specific DVD video disc.

●

surface.

player for the drawer to be opened.

● There must be sufficient room in front of the

EN 8 DVD 620 /0X13.

TO VIDEO INTO SCART IN

AUDIO SYSTEM

TO AUDIO IN

COAXIAL

DIGITAL AUDIO OUT

PCM-MPEG2-Dolby Digital

TV OUT

(CVBS)

VIDEO OUT

AUDIO OUT

Preparation

English

If your TV has a CVBS Video input

connector,

Connect the CVBS VIDEO OUT on the DVD

player to the CVBS VIDEO IN.

Connect the Left and Right AUDIO OUT on the

DVD player to the Left and Right AUDIO IN on

the TV.

Directions for Use

(CVBS)

VIDEO OUT

AUDIO OUT

TO AUDIO IN TO VIDEO IN

TO SCART IN

DIGITAL AUDIO OUT

PCM-MPEG2-Dolby Digital

TV OUT

COAXIAL

Connecting to an Audio System

You can also listen to the sound of audio CDs

and DVD video discs by connecting to an

optional stereo system.

Connect the Left and Right AUDIO OUT on the

DVD player to the Left and Right AUDIO IN on

the stereo system.

VCR, Stereo System or other devices as

necessary to make the best connections.

depending on the capabilities of your existing

equipment.

The following guidelines are options for the best

Basic Connections

● Please refer to the instruction books of your TV,

● Make one of the following connections,

POWER B

picture and sound quality available on your DVD

standby-on mode

– switch DVD ON or go to

0-9 numerical key pad

was stopped

player.

Picture

Use the CVBS Video Ouput for good picture

quality.2Use SCART Output for best picture quality.

– select numbered items in a

DISC MENU

playback

DISPLAY

– display bit rate indicator during

1 2 3 4

item in the menu

Sound1Digital audio connections provide the clearest

sound. Connect one of the DVD player’s

DIGITAL AUDIO OUT (COAXIAL) to your

amplifier or receiver.2If digital connections are not possible, connect

system menu

SYSTEM MENU

– access or remove player’s

the DVD player’s red and white AUDIO OUT to

your amplifier, receiver, stereo or TV.

Warning!

– Never make or change connections

with the power switched on.

or track

– search forward* / next chapter

SUBTITLE

– subtitle language selector

STOP ( 9 )

PLAY ( B )

– stop playback

– start playback

– Connect the DVD player directly to

your TV, instead of eg. a VCR, to avoid

distortion because DVD video discs are

ANGLE

– select DVD camera angle

PAUSE ( ; )

copy protected.

– Do not connect the DVD player AUDIO

OUT to PHONO IN of your amplifier or

receiver.

ZOOM

– enlarge video image

AUDIO

– audio language selector

REPEAT

Connecting to a TV

Connect the SCART (TV OUT) to the

SHUFFLE

REPEAT (A-B)

corresponding connector on the TV IN.

Note:

– Ensure that the “TV” indication on SCART

cable is connected to the TV set and “DVD”

indication on SCART cable is connected to the

DVD player.

SCAN

If your TV is not equipped with a SCART input,

you can select the following connection:

* Press and hold key for about two seconds

Functional Overview

Remote Control

English

RETURN / RESUME

continue playback after play

– go back to previous menu /

– access menu of a DVD disc

– acknowledge menu selection

– (left/right/up/down) select an

previous chapter or track

– search backward* / go to a

frame-by-frame playback

– pause playback temporarily /

– repeat a specific segment

– repeat chapter, track, title, disc

track/chapter within a disc

– play tracks in random order

– play the first 10 seconds of each

Directions for Use

English

NTSC/PAL Conversion

This player is equipped with an NTSC/PAL

conversion feature that converts the video

output of the disc to match your TV system. To

activate the conversion refer to page 13.

Switching On

Switch on the TV and DVD player.2Set the TV to the correct Video IN channel. (eg.

EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc.

(Refer to your TV owner’s manual for detail)

➜ The player display lights up and the default

screen appears on the TV.3If you are using an external equipment (eg. audio

system or receiver), turn them on and select the

appropriate input source that was used to

connect to the DVD player output. Refer to the

equipment owner’s manual for detail.

Menu Bars on TV Screen

● Operations can be carried out directly via the

multiple menu bars on the TV screen.

● The following functions are available via the

menu bars. Pressing SYSTEM MENU keys

repeatedly will toggle through menu bar 1, menu

bar 2, menu bar 3 and menu bar OFF:

Menu bar 1

From the left,

Personal Preferences ➜ Subtitle Language ➜

Audio Language ➜ Colour ➜ Sound

Menu bar 2

From the left,

Step by step playback ➜ Slow motion ➜

Fast motion ➜ Angle ➜ Zoom

Menu bar 3

From the left,

Title ➜ Chapter ➜ Time Search ➜

Favourite Track Selection (FTS)

Temporary Feedback Field Icons

These icons will appear on the top left hand

corner of your TV screen.

Preparation

Repeat A to end

Repeat A–B

Angle

Scan

Repeat All

Repeat Title

Child Safe

Child Lock On

Repeat Track

Repeat Chapter

Resume

Shuffle

EN 9DVD 620 /0X1 3.

Action Prohibited

Shuffle Repeat

Inserting batteries into the

Remote Control

Open the battery cover.2Insert batteries (AA size) with the correct

Dolby Digital™ decoder allows you to enjoy the

Connecting to Optional

Equipment

Preparation

● A digital component with a built-in MPEG 2 or

English

polarity as indicated by the + and - symbols

inside the battery compar tment.3Close the cover.

surround sound while producing the effect of

being in a movie theater or a concert hall.

from the DIGITAL OUT COAXIAL connectors.

If your receiver has a MPEG 2 or Dolby

Digital™ decoder,

Connect the COAXIAL DIGITAL AUDIO OUT

of the DVD player to the COAXIAL DIGITAL

AUDIO IN on your receiver.2You will need to set the DVD player’s digital

output to ALL (see ‘Personal Preferences’).

● The player outputs the surround sound signals

CAUTION!

– Remove batteries if they are exhausted

or not to be used for a long time.

– Do not use old and new or different

types of batteries in combination.

– Batteries contain chemical substances,

so they should be disposed off properly

and kept away from children.

Using the Remote Control

● Direct the remote control at the remote sensor

REAR

SPEAKERS

TO VIDEO IN

TO SCART IN

RECEIVER with

Digital™ decoder

MPEG 2 or Dolby

REAR

SPEAKERS

of the DVD player.

hot or humid place.

remote control.

● Do not drop the remote control.

● Do not leave the remote control near extremely

● Do not spill water or put anything wet on the

(CVBS)

VIDEO OUT

AUDIO OUT

TV OUT

DIGITAL AUDIO OUT

PCM-MPEG2-Dolby Digital

COAXIAL

TO COAXIAL IN

Notes:

– If the audio format of the digital output does

not match the capabilities of your receiver, the

receiver will produce a strong, distorted sound or

no sound at all.

– To see the selected audio format of the

current DVD in the Status Window, press SYSTEM

MENU.

EN 10 DVD 620 /0X13.

English

– TV System (NTSC/PAL Conversion)

Allows you to select between PAL, NTSC and

AUTO mode depending on your TV.

The conversions supported are as follows:

NTSC

PAL

NTSC

Not

Supported

PAL

NTSC

PAL

NTSC

PAL

Disc

Output format

Type

DVD

VCD

NTSC

Format

Selected mode

PAL

NTSC

PAL

NTSC

PAL

AUTO

In the Personal Preferences Menu, select TV

System.2Press 3 or 4 to select PAL, NTSC or AUTO.

Notes:

– AUTO can only be selected when using a TV

that has both the NTSC and PAL systems.

– This is applicable for CVBS output on cinch

and SCART only.

– Slight picture distortions may occur due to this

conversion. This is normal. Thus, the AUTO format

is most suitable for the best picture quality.

Sound

– Digital output

¶ Digital output selection enables you to specify

the type of digital output which is suitable to

your receiver.

¶ Select ALL (default setting), if you had connected

your DIGITAL AUDIO OUT to a multichanel

decoder receiver.

¶ Select PCM only if your receiver is not capable

of decoding multichannel audio.

¶ Select OFF to deactivate the DIGITAL AUDIO

OUT.

– Analogue output

Select Stereo, Dolby Surround-compatible or 3D

Sound output to match your system’s playback

capability.

– Night Mode

When set to ON, the dynamics of your sound

output are optimised. High volume outputs are

softened, enabling you to watch your favourite

action movie without disturbing others.

– Karaoke vocal

Put this setting to ON only when a multi-channel

karaoke DVD is being played. The karaoke

channels on the disc will then be mixed into a

normal stereo sound.

Preparation

Directions for Use

Preparation

– Black level shift (NTSC output only)

Select ON for adapting the colour dynamics to

obtain richer contrasts.

Personal Preferences

In the Personal Preferences settings menu, you

can customize you player to suit your own

particular requirements.

General operation:

English

– Video shift

Use this setting to personalize the position of

the picture on your TV by scrolling it to the left

or right.

Press SYSTEM MENU on the remote control.

The will be highlighted in the menu bar.3Press 4 to activate the Personal Preferences

menu.4Use the 1 2 3 4 keys to toggle through the

functions and select your preferred option.5Press OK to confirm a highlighted selection.

The following items are available:

Picture

– TV Shape

Select the aspect ratio of the TV to be

connected.

16:9 ➜ when you connect a wide-screen TV to

the DVD player.

– Smart Picture

¶ Colour settings

4:3 LETTER BOX ➜ when you connect a

normal TV to the DVD player. Displays a wide

picture with bands displayed on the upper and

You can select one of five predefined sets of

colour settings and one set (Personal) which you

lower portions of the TV screen.

4:3 PAN SCAN ➜ when you connect a

can define yourself.

normal TV to the DVD player. Displays the wide

picture on the whole TV screen with a portion

automatically cut off.

16:9

tune saturation, brightness and contrast

parameters.

¶ When Personal is selected it allows you to fine-

¶ Use 3 or 4 keys to adjust the values of these

4:3

Letter Box

4:3

Pan Scan

Note:

– Pan Scan is subject to availability on the disc.

Directions for Use

English

Basic Playback

Press STANDBY ON on the front panel.

Press OPEN/CLOSE / on the front panel to

open disc loading tray.3Place the chosen disc in the tray, with the label

facing up.4Press OPEN/CLOSE / again to close the tray.

➜ READING appears in the status window and

on the player display, and playback starts

automatically.

Notes:

– DVDs may have a region code. Your player will

not play discs that have a region code different

from the region code of your player.

– If ‘Child Lock’ is set to ON and the disc

inserted is not authorised, the 4-digit code must

be entered and/or the disc must be authorised

(see ‘Access Control’).

Playing a DVD-Video

● DVD video discs may have one or more TITLES,

and each TITLE may have one or more

CHAPTERS.

● Playback stops at the end of each TITLE.

TITLE 1 TITLE 2

CHAPTER 1 CHAPTER 2 CHAPTER 1 CHAPTER 2 CHAPTER 3

DVD-VIDEO DISC

Playing a title

Insert a disc and close the tray, playback starts

automatically.

➜ The TV screen’s and DVD player’s display

shows the type of disc loaded, disc’s information

and playing time.2When the Disc Menu appear on the TV screen,

use 431 2 keys or numerical keys on the

remote control to select an option and continue

playback.3If the titles are numbered , press the numerical

keys or use the 4 3 keys to select desired title

in the menubar.4To stop playback, press STOP.

Smart Resume

● In stop mode and when a disc has not been

ejected,

➜ Pressing PLAY will automatically resume

playback from the point where the playback was

last stopped.

To deactivate auto resume,

● Press STOP to stop playback.

➜ The help line text appears “Press Stop again to

start from begining” for 5 seconds.

● Press STOP again or unload the discs, the auto

resume is cancelled.

To activate auto resume,

● Reload the disc and press PLAY.

➜ Playback starts from the begining of the title.

● When resume icon . appears on the screen,

press PLAY again.

➜ Playback will resume from the point where

the playback was last stopped.

Note:

– Resume feature is also applicable to VCDs

and SVCDs.

Operation

EN 11DVD 620 /0X1 3.

– Bit Rate Indicator

Press the DISPLAY key to activate the bit rate

Language

Selecting disc languages:

Preparation

English

indicator. When activated, the bit rate for video

and audio, as well as the total bit rate is

Menu/Audio/Subtitle language

displayed. This is only applicable during playback

of DVD and SVCD discs.

language and the language used in TV screen

menus or DVD menus which will always be used

for every disc to be played back.

● This is to select the audio language, subtitle

● If the language selected is not available on the

– Help text

When set to ON, help text describes the icons

selected. Select OFF if you no longer require the

help text.

– PBC (Playback Control - for VCD)

The Playback Control can be set to ON or OFF.

– Smart Power OFF

disc, the original language designated by each

disc will be selected.

Features

– Access Control

Access Control contains the following features:

Child Lock - When Child Lock is set to ON, a 4-

digit code needs to be entered in order to

playback discs.

Parental control - Allows the conditional

presentation of DVDs containing Parental

Control information (see ‘Access Control’

section).

Puts the set to standby after a predefined time.

This can be set to Enable or Disable.

– Status Window

Displays the current status of the player and

appears with the menu bar. When disc playback

is stopped, it is displayed with the ‘Temporary

Feedback Field’ in the default screen. See ‘On-

Screen Display’ information;

Factory setting is ON. Select OFF to suppress

display of the Status Window.

EN 12 DVD 620 /0X13.

English

Changing the audio language

Select Y (AUDIO) in the menu bar or press

the AUDIO button on the remote control

directly.2Press AUDIO or 3/4 repeatedly to select the

different languages.

Subtitles

Select Z (SUBTITLE) in the menu bar or

press the SUBTITLE button on the remote

control directly.2Press SUBTITLE or 3/4 repeatedly to select

the different subtitles.

Special VCD & SVCD Features

Playback Control (PBC)

Load a Video CD with PBC and press PLAY.2Go through the menu with the keys indicated on

the TV screen until your chosen passage starts to

playback. If a PBC menu consists of a list of

tracks, you can select a track directly.3Enter your choice with the numerical keys (0-9).4Press RETURN to go back to the previous menu,

if applicable on the menu.5You may also select PBC OFF under Personal

Preferences.

➜ PBC menus are not activated for further

playback.

General Features

Note:

– Unless stated, all operations described are

based on remote control use. Some operations

can be carried out using the menu bar on the TV

screen.

Moving to another title/chapter

When a disc has more than one title/track or

chapter, you can move to another title/chapter as

follows:1Press SYSTEM MENU, then select W or X in

the menu bar.2Press 34 or numerical keys to select a title/

chapter.

Press T or S briefly during playback to go

to the next track or to return to the beginning

of the currect track respectively.2Press S twice briefly to step back to the

previous track.3To go directly to any track, enter the track

number using the numerical keys (0-9).

Note:

– Long press of the T or S keys will

switch the DVD player on BACKWARD or

FORWARD search (see SEARCH section).

Select (FAST MOTION) in the menu bar and

press 4.

Use the 1 2 keys to select the required speed: -

32, -8 or -4 (backward), or +4, +8, +32

(forward).3Select 1 to play the disc at normal speed again.

To exit FAST MOTION mode, press PLAYor 3.

● To search forward or backward through different

speeds, you can also hold down T or S

respectively.

Operation

Directions for Use

VCD

DVD

VCD

DVD

Operation

Playing a disc

Playing a Video CD

English

Insert a disc and close the tray, playback starts

automatically.

➜ The menu bar on TV screen will display the

number of tracks for selection.

Playback will stop at the end of the disc.3To stop playback, press STOP.

TRACKS may have one or more INDEXES.

move between TRACKS and INDEXES.

● Video CDs may have one or more TRACKS, and

● To make easy and convenient access, you can

● Some Video CDs have Play Back Control (PBC),

Special DVD Features

DVDs may contain menus to navigate the disc

and access special features. Press the appropriate

numerical key or use the 4, 3, 2, 1 keys to

highlight your selection in the DVD menu and

VIDEO CD

TRACK 1 TRACK 2

which is a predefined playback sequence stored

INDEX 1 INDEX 2 INDEX 1 INDEX 2 INDEX 3

on the disc (see Playback Control section).

press OK to confirm.

Title/Disc menu

Press DISC MENU.

Playing a disc

Insert a disc and close the tray, playback starts

automatically.

➜ If the current title has a menu, the menu will

appear on the screen. Otherwise, the disc menu

will be displayed.2If disc menu is available on the disc, audio

➜ The number of tracks and the total playing

time of the disc will appear on the TV screen and

DVD player’s display.2Press PLAY.

language, subtitle options, chapters for the title

and other options will appear for selection.

To remove the title/disc menu, press DISC

MENU again.

Camera Angle

Some discs contain scenes which have been shot

simultaneously from various angles.

This DVD player allows you to select the desired

camera angle.

➜ The current track number and its elapsed

playing time will be displayed.3Playback will stop at the end of the disc.4To stop playback, press STOP.55 Disc Resume feature is also applicable for

VCDs and SVCDs (see 5 Disc Resume section).

● When the DVD player encounters a scene shot

Playing an Audio CD

the audio output connected to a stereo system

● Audio CDs contain only TRACKS.

● They can be played on your DVD player with

in multiple angles, it will give you an indication on

the “Temporary Feedback Field.”

➜ The angle icon remains displayed until multiple

angles are no longer available.

● Use the 3/4 to select the required angle icon.

or to your TV.

screen or by pressing the numerical keys directly.

Favourite Track Selection (FTS) programmes for

● Select tracks using the menubar on the TV

● Your DVD player also allows you to compile

➜ Playback changes to the selected angle.

bar or press the ANGLE button on the remote

control directly.

● You can also select } (ANGLE) in the menu

TRACKS

AUDIO CD

your discs by selecting or excluding tracks of

your choice (see FTS Programme - Audio CDs).

2 3 5 6 7 8 9 10 11 12 ...41

Directions for Use

English

Shuffle

DVD

This shuffles the playing order of chapters within

a title, if the title has more than one chapter.1Press SHUFFLE during playback.

➜ SHUFFLE appears on the screen for about

two seconds.2To return to normal playback, press SHUFFLE

again.

VCD

This shuffles the playing order of tracks within a

disc , if the disc has more than one tracks.1Press SHUFFLE during playback.

➜ SHUFFLE appears on the screen for about

two seconds.2To return to normal playback, press SHUFFLE

again.

Time search

DVD

VCD

The Time Search function allows you to start

playing at any chosen time on the disc.1Select (TIME SEARCH) in the menu bar and

press 4.

➜ Playback will pause.

➜ The elapsed playing time is displayed in a time

edit box.

Enter hours, minutes and seconds from left to

right in the time edit box using remote control

numerical key pad.

➜ Each time an item has been entered, the next

item will be highlighted.

Press OK to confirm the selected time.

➜ The time edit box will disappear and playback

starts from the selected time position on the

disc.

Press SYSTEM MENU to remove the menu bar.

Zoom

VCD

The Zoom function allows you to enlarge the

video image and to pan through the enlarged

image.1Select (ZOOM).2Press 3/4 to activate the ZOOM function and

select the required zoom factor: 1.33 or 2 or 4.

➜ Playback will continue.

➜ The selected zoom factor and ‘Press OK to

pan’ appears below the menu bar.

➜ The zoomed picture will appear on the TV

screen.3Press OK to confirm the selection.

➜ The panning icon appears on the screen.

Use the 1 2 3 4 keys to pan across the screen.

When OK is pressed only the panned picture

will be shown on the screen.

To exit ZOOM mode, select zoom factor to

“Off” (zoom factor 1) in the menu bar.

FTS Video/Audio Programme

● Favourite Track Selection (FTS) list contains 20

items (titles, chapters).

● The most recent programme list will be placed

on top of the existing list.

Storing a Programme1While playback is stopped, select VIDEO FTS

c in the menu bar.2Press 4 to open the menu bar.

➜ The VIDEO FTS c menu appears.3Press 2 or 1 or FTS (on the remote control) to

select ON.

Operation

EN 13DVD 620 /0X1 3.

DVD

VCD

DVD

Operation

DVD

Repeat

Repeat chapter/title/disc

● To repeat the current chapter, press REPEAT.

VCD

DVD

Slow Motion

Select (SLOW MOTION) in the menu bar

Use the cursor keys 1 2 to select the required

and press 4.

➜ Playback will pause.

English

appears on the front display.

CHP

RPT

➜

second time.

● To repeat the current title, press REPEAT a

appears on the front display.

TTL

ALL

RPT

➜

time.

➜

● To repeat the entire disc, press REPEAT a third

● To exit Repeat mode, press REPEAT a four th time.

appears on the front display.

TRK

RPT

VCD

Repeat track/disc

➜

● To repeat the current track, press REPEAT.

VCD

DVD

speed: -1, -1/2, -1/4 or -1/8 (backward), or +1/8,

+1/4, +1/2 or +1 (forward).

Select 1 to play the disc at normal speed again.

If ; is pressed, the speed will be set to zero

(PAUSE).5To exit slow motion mode, press PLAY.

Still Picture and Frame-by-frame

playback

Select (STEP) in the menu bar and press 4.

Use the cursor keys 1 2 to select the previous

➜ Playback will pause.

VCD

DVD

appears on the front display.

ALL

RPT

time.

● To repeat the entire disc, press REPEAT a second

or next picture frame.3To exit step by step playback, press PLAY or 3.

Repeat A-B

➜

● To exit Repeat mode, press REPEAT a third time.

Note:

– You can also activate frame-by-frame

playback by pressing the PAUSE key repeatedly

– DVD-Video Discs: repeat a sequence in a

title

– Video and Audio CDs: repeat a sequence

in a track1Press REPEAT A-B at your chosen starting point.2Press REPEAT A-B again at your chosen end

VCD

DVD

on the remote control.

Scan

Scanning plays the first 10 seconds of each

chapter/track on the disc.1Press SCAN.2To continue playback at your chosen chapter/

appears briefly on the front display,

RPT

point.

➜

To exit the sequence, press REPEAT A-B.

and the repeat sequence begins.

track, press SCAN again or press PLAY.

EN 14 DVD 620 /0X13.

English

Child Lock

DVD

VCD

Activating/deactivating the Child

Lock

When disc playback is stopped, select ACCESS

CONTROL in the Personal Preferences menu

using the 3/4 keys.2Enter a 4-digit code of your own choice twice.3Move to “CHILD LOCK” using the 3/4 keys.4Move to Ç / É using the 2 keys.5Select Ç using the 3/4 keys.6Press OK or 1 to confirm, then press 1 again to

exit the Personal Preferences menu.

➜ Now unauthorised discs will not be played

unless the 4-digit code is entered.

Select É to deactivate the CHILD LOCK.

Notes:

Confirmation of the 4-digit code is necessary

when:

– The code is entered for the very first time (see

above),

– The code is changed or cancelled (see

‘Changing the 4-digit code’),

Authorising discs

Insert the disc.

➜ The ‘child safe’ dialog will appear.2You will be asked to enter your secret code for

‘Play Once ‘or ‘Play Always.’

● If ‘Play Once’, disc can be played when in the

player and the player is ON.

● If ‘Play Always’, disc will become authorised and

can always be played, even if the Child Lock is

set to ON.

Notes:

– The player memory can maintain 120

authorised (‘Child safe’) disc titles. A disc will be

placed in the list when ‘Play Always’ is selected.

– Each time a ‘child safe’ disc is played, it will be

placed on top of the list. When the list is full, the

last disc in the list will be replaced when a new

disc is added.

– Double-sided DVDs and multi-volume VCDs

may have a different ID for each side. In order to

make the disc ‘child safe’, each side has to be

authorised.

Deauthorising discs

Insert the disc.

➜ Playback starts automatically.2Press 9 while { is visible.

➜ The | will appear and the disc is now

deauthorised.

Parental Control

Movies on DVDs may contain scenes not

suitable for children. Therefore, discs may contain

‘Parental Control’ information which applies to

the complete disc or to certain scenes on the

disc. These scenes are rated from 1 to 8, and

alternative, more suitable scenes are available on

the disc. Ratings are country dependent. The

‘Parental Control’ feature allows you to prevent

discs from being played by your children or to

have certain discs played with alternative scenes.

Access Control

Directions for Use

DVD

Operation

Storing a Programme1Load a disc and stop playback.2Press 4 to go to the list of available tracks.3Use 2 and 1 to select the required tracks or

Storing titles/tracks

Press 4 to select TITLES/TRACKS.2Use 2 and 1 to select the require title/tracks.3Press OK to store the entire selected title/tracks.

English

directly using remote control numeric key.4Press OK to store the selected tracks.

➜ The track number will be added to the list of

selections.

Switching a Programme ON/OFF

Use 34 to move and select desired tracks.2Press 2 or 1 to select either ON or OFF.

➜ The title number will be added to the list of

selections.

Storing chapters/indexes1Press 4 on the selected chapter/indexes number.

➜ The chapter/indexes number will be

highlighted.

Use 2 and 1 to select the required chapter

number.3Press OK to confirm the selection.

Erasing a track in a Programme1Use 4 to go to the programmed tracks.2Use 2 and 1 to select the required number.3Press OK to erase the selection.

Press SYSTEM MENU to exit.

Erasing all selections

➜ All selections will be erased.

● Use 4 to select CLEAR ALL and press OK.

➜ The selected chapter/indexes confirmation

will be added to the list of selections.

Press SYSTEM MENU to exit the VIDEO FTS

c menu.

Erasing a selection in a Programme1While playback is stopped, select VIDEO FTS

c in the menu bar.2Use 4 to select PROGRAM.3Use 2 and 1 to select the required number.4Press OK to erase the selection.

Press SYSTEM MENU to exit.

Erasing all selections

While playback is stopped, select VIDEO FTS

c in the menu bar.2Use 4 to select CLEAR ALL and press OK.

➜ All selections will be erased.3Press SYSTEM MENU to exit.

Directions for Use

English

Troubleshooting

WARNING

Under no circumstances should you try to repair the system yourself, as this will invalidate the

warranty. Do not open the system as there is a risk of electric shock.

If a fault occurs, first check the points listed below before taking the system for repair. If you

are unable to remedy a problem by following these hints, consult your dealer or service centre.

Problem Solution

No power – Check if the AC power cord is properly

connected.

– Press Standby-On key on the DVD player.

No picture – Check if the TV is switched on.

– Check the video connection.

Distorted picture – Sometimes a small amount of picture distortion

may appear. This is not a malfunction.

Completely distorted picture or – Make sure the NTSC/PAL setting at the DVD

black/white picture with DVD player matches the video signal of your television.

or Video CD (See NTSC/PAL Conversion/Settings)

No sound or distorted sound – Adjust the volume.

– Check that the speakers are connected correctly.

– Select another audio language (if available on the

DVD video disc)

No audio at digital output – Check the digital connections.

– Check the settings menu to make sure the digital

output is set to ALL or PCM.

– Check if the audio format of the selected audio

language matches your receiver capabilities.

No sound and picture – Check that the SCART cable is connected to the

correct device (See Connecting to a TV)

Disc can’t be played – Ensure the disc label is facing up.

– Check if the disc is defective by trying another

disc.

No return to start-up screen when – Reset the unit by switching the player off, then on

disc is removed again.

The player does not respond to – Aim the remote control directly at the sensor on

the remote control the front of the player.

– Reduce the distance to the player.

– Replace the batteries in the remote control.

– Re-insert the batteries with their polarities (+/–

signs) as indicated.

Buttons do not work or player stops – To completely reset the player, unplug the AC

responding cord from the AC outlet for 5-10 seconds.

Player does not respond to some – Operations may not be permitted by the disc.

operating commands during playback. Refer to the instructions of the disc.

DVD Video player cannot read – Use a commonly available cleaning CD/DVD to

CDs/DVDs clean the lens before sending the DVD Video

player for repair.

EN 15DVD 620 /0X1 3.

Changing the 4-digit code

When disc playback is stopped, select ACCESS

CONTROL in the Personal Preferences menu

using the 3/4 keys.2Enter the current 4 digit code.3Move to CHANGE CODE using the 4 and

Activating/Deactivating Parental

Access Control

English

Control

When disc playback is stopped, select ACCESS

CONTROL in the Personal Preferences menu

using the 3/4 keys.2Enter your 4-digit code. If necessary, enter the

press the 2 key.4Enter the new 4-digit code.5Enter the code a second time and reconfirm by

code a second time.3Move to Parental Control using the 3/4

pressing OK.

Press 1 to exit the menu.

➜ The new 4 digit code will be take effect.

keys.4Move to value adjustment (1-8) using the 2 key.5Then use the 3/4 keys or the numerical keys on

the remote control to select a rating from 1 to 8

If you forget your 4 digit code

Press 9 to exit the ‘Child Safe’ screen.2Select ACCESS CONTROL in the Personal

Preferences menu using the 3/4 keys.3The 4-digit code can be cancelled by pressing 9

four times in the ‘Access Control’ dialog.4You can then enter a new code (twice!) as

described above in ‘Changing the 4 digit code’.

Parental Control Disclaimer

This DVD player features the PARENTAL

Ratings 1 to 8:

Rating 0 (displayed as ‘– –’):

Parental Control is not activated. The Disc will be

played in full.

for the disc inserted.

The disc contains scenes not suitable for children.

If you set a rating for the player, all scenes with

the same rating or lower will be played. Higher

rated scenes will not be played unless an

alternative which has the same rating or lower is

available on the disc. If no suitable alternative is

found, playback will stop and the 4-digit code has

CONTROL system which is to activate when

playing DVD discs furnished with certain

software coding only.

Also note that at the time of release of this DVD

player, certain aspects of the technical standards

had not been settled between set makers and

the disc industries.

On this basis, Philips cannot guarantee the

functioning of the PARENTAL CONTROL

system and denies any liability associated with

to be entered.

Press OK or 1 to confirm, then press 1 again to

exit the Personal Preferences menu.

unintended watching of disc content.

If in doubt, please make sure the disc plays

according to your PARENTAL CONTROL

settings before you allow children access to the

player.

Country

When disc playback is stopped, select ACCESS

CONTROL in the Personal Preferences menu

using the 3/4 keys.2Enter the 4-digit code.3Move to CHANGE COUNTRY using the 4

key.4Press the 2 key.5Select a country using 3/4.6Press OK or 1 to confirm, then press 1 again to

exit the menu.

EN 16 DVD 620 /0X14.

Mechanical- and Dismantling Instructions

4. Mechanical- and Dismantling Instructions

Dismantling Instructions

Power supply unit 1200

Remove cable connections

Remove 2 screws 0223

(board to bottom frame)

Release 2 spacer locking 0213

(board to bottom frame)

Dismount board

Mounting

Dismounting

Motherboard 1500

Remove DVD Loader 0001

and Power supply unit 1200

(see respective instruction)

Remove flex and cable

connections

Remove 5 screws 0227

(skt cinch, scart and optical to

back-plate) and 4 screw 0222

(board to bottom frame)

Dismount board

Remove 4 screws to remove loader.

101201

CL 16532162_003.eps

TopCover 0232

Remove 7 screws 233

Lift cover to remove

DVD Monoboard 1001

Remove flex and cable

connections from DVD loader

and Motherboard

Remove 4 screws 0228

(Monoboard to bottom frame)

Dismount board

DVD Loader 0001

Remove flex and cable connections

to monoboard 1001

Open tray (see instruction below)

Unlock Tray cover 0219

Remove 4 screws 0217

(Loader to bottom frame)

Close tray

Lift module up slightly and move

backward to remove.

When a disc is loaded, unlock the tray by pushing the slide inwards with

Front Standby board 1700

Remove cable connection

Remove 2 screws 0211

( board to Front panel )

Dismount board

a screwdriver and pull tray outwards.

DISMANTLING INSTRUCTIONS

See exploded view for item numbers

Front Panel 0200

Remove cable connections

Unlock Tray cover 0219 and close tray

Unlock Front panel from frame by

releasing successively 5 snaps

(2 on the side and 3 on the bottom )

Place Front panel in front of

Open Tray (see instruction below)

the set ( service position )

Front control board 1600

Remove cable connection

Remove 3 screws 0211

(board to Front panel)

Dismount board

When it is not possible to open the tray with the EJECT button,

the tray can manually be opened.

Manually opening of tray

When no disc is loaded, unlock the tray by moving the slide from left

to right and pull tray outwards.

Exploded View

Mechanical- and Dismantling Instructions

EN 17DVD 620 /0X1 4.

201201

CL 16532162_001.eps

0001

1001

1500

1600

1700

EN 18 DVD 620 /0X15.

Diagnostic Software Descriptions and Troubleshooting

5. Diagnostic Software Descriptions and Troubleshooting

5.1 Dealerscript

5.1.1 Purpose of Dealer Script

The dealer script can give a diagnosis on a standalone DVD player, no other equipment is needed to perform a number of hardware tests to check if the DVD player is faulty. The diagnosis is simply a "error" or "pass" message. No indication is given of faulty hardware modules. Only tests within the scope of the diagnostic software will be executed hence only faults within this scope can be detected.

Nucleus

Display Nucleus Nucleus Description

Countdown Number Name

6 6 PapChksFl Calculate and verify checksum of FLASH memory

5 12 PapI2cDisp

4 13 PapS2bEcho Checks the I2C interface to the basic engine 3 11 PapI2cNvram Checks the I2C interface with the NVRAM 2 15 PapNvramWrR Pattern test of all locations in the NVRAM 1 16 CompSdramWrR Pattern test of all locations in the SDRAM(s)

5.1.2 Contents of Dealer Script

The dealer script executes all diagnostic nuclei that do not need any user interaction and are meaningful on a standalone DVD player. The nuclei called in the dealer script are the following (the number after each nucleus name corresponds with the number being on the local display when the nucleus is executed during the dealer script):

Checks the I2C interface with the slave processor on the display board

CL 16532162_026.eps

Figure 5-1

080102

Dealer Script

Press 2 keys simultaneously

Connect to mains.

During the test, the following display is shown: the counter counts down from the number of nuclei to be run before the test finishes. Example:

SET O.K.?

YES

To exit DEALER SCRIPT, disconnect from mains

CL 16532162_027.eps

Figure 5-2

090102

+ 41 hidden pages