Philips CED750/55 User Manual
Register your product and get support at
www.philips.com/welcome
CED750
EN User manual
Contents
1 Important 4
Safety 4
Notice 4
2 Your Car Entertainment System 6
Introduction 6
What’s in the box 6
Overview of the main unit 7
Overview of the remote control 8
3 Get started 10
Install the car audio 10
Install remote control battery 16
Turn on 17
Set clock 17
4 Listen to radio 18
Tune to a radio station 18
Store radio stations in memory 18
Tune to a preset station 19
5 Play 20
Load discs 20
Insert USB or SD/MMC card 20
Play/Pause 21
Search for a folder 21
Search within a title/folder 21
Repeat 22
Repeat a section 22
Random play 22
Select audio language 23
Select audio mode 23
Select subtitle language 23
Change view angle 23
Rotate pictures 23
Zoom 23
Select slide show duration 24
6 Play with Bluetooth device 25
Pair the Bluetooth-enabled devices 25
Make a call 25
Receive call 26
Switch phone call to the mobile 26
Listen to music from Bluetooth device 26
7 Adjust sound 27
Adjust volume 27
Mute 27
Select preset equalizer 27
Adjut fader/balance 27
8 Adjust settings 28
Adjust general system settings 28
Adjust sound settings 29
Adjust video settings 29
Adjust Bluetooth settings 29
Adjust language settings 30
Adjust volume settings 30
Adjust DVD rating 31
9 Others 32
Listen to other devices 32
Reset 32
Remove the unit 32
Replace fuse 33
10 Product information 34
11 Troubleshooting 36
About Bluetooth device 36
12 Glossary 38
English
Contents
EN
3
1 Important
Safety
•
Read and understand all instructions
before you use your unit. If damage is
caused by failure to follow instructions, the
warranty does not apply.
•
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
•
This unit is designed for negative ground
(earth) 12 V DC operation only.
•
To reduce the risk of traffi c accident, do no
watch video during driving.
•
To ensure safe driving, adjust the volume to
a safe and comfortable level.
•
Improper fuses can cause damage or
fi re. When you need to change the fuse,
consult a professional.
•
Use only the supplied mounting hardware
for a safe and secure installation.
•
To avoid short circuit, do not expose the
unit, remote control or remote control
batteries to rain or water.
•
Never insert objects into the ventilation
slots or other openings on the unit.
•
Clean the unit and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the unit.
•
Never place any objects other than discs
into the unit.
•
Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
•
Visible and invisible laser radiation when
open. Avoid exposure to beam.
•
Risk of damage to the unit screen! Never
touch, push, rub or strike the screen with
any object.
Notice
Notice of compliance
The set complies with the FCC-Rules, Part 15
and with 21 CFR 1040.10. Operation is subject
to the following two conditions:
1.This device may not cause harmful
interference, and
2.This device must accept any interference
received, including interference that may cause
undesired operation.
FCC Notice (For U.S. and Canada)
Note:
This equipment has been tested and found
to comply with the limits for a Class B digital
device,pursuant to par t 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to tr y to correct the
interference by one or more of the following
measures:
– Relocate the receiving antenna.
– Increase the separation between the
equipment and receiver
– Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
IMPORTANT!
Modifi cations not authorized by the
manufacturer may void users authority to
operate this device.
4
EN
The making of unauthorized copies of copyprotected material, including computer
programs, fi les, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
Offi cal DivX® Certifi ed product. Plays all
versions of DivX® video (including DivX® 6)
with standard playback of DivX® media fi les.
“DivX, DivX” Certifi ed, and associated logos
are trademarks of DivX, Inc. and are used under
license.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
Other trademarks and trade names are those
of their respective owners.
This unit includes this label:
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Any changes or modifi cations made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
2008 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specifi cations are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
English
Important
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
EN
5
2 Your Car
Entertainment
a
a
b
b
System
Congratulations on your purchase, and
welcome to Philips! To fully benefi t from the
support that Philips offers, register your product
at www.Philips.com/welcome.
Introduction
With the car entertainment system, you and
your passengers can enjoy:
Audio/video/JPEG pictures from
•
DVD, VCD or CD
•
USB devices
•
SD/SDHC/MMC cards
•
External devices
•
FM or AM (MW) radio
•
Audio from Bluetooth-enabled devices
•
You can also make/receive phone calls with
Bluetooth-enabled devices.
What’s in the box
Check and identify the contents of your
package:
c
c
e
e
hi
hi
k l
k l
d
d
gf
gf
a Main unit
b Trim plate x 2 pcs
c Standard connector
d Remote control
e Short mounting bracket x 2 pcs
f Rubber cushion
g Screws
- M5x16mm x 1 pcs
- M4x3mm x 4 pcs
- M5x5mm x 2 pcs
- M5x5.5mm x 4 pcs
- M5x6mm x 1 pc
h AV cable
i Bluetooth microphone cable
j Remote control battery
k User manual
l Quick start guide
j
j
6
EN
Overview of the main unit
q
r
q
r
a
a
p
p
b
b
o
o
c
c
n
n
d
d
m
m
e
e
l
l
k
k
AV I N
AV I N
j
j
f
f
i
i
h
h
g
g
English
Your Car Entertainment System
a OPEN
•
Open or close the screen.
b INTRO.SCH
•
Search for radio station.
•
Search for radio station and save the
top six stations with strong signal into
preset channels automatically.
c EQ
Select equalizer (EQ) setting.
•
d DISP
•
Display play information.
e Disc slot
f Small screen
g
Eject disc.
•
EN
7
h 4 WAY NAVIGATION
Navigate to left/right
•
Tune for radio station.
Skip to the previous/next track/
chapter.
Move cursor to left/right.
Navigate up/down
•
Skip to the previous/next preset
station.
Skip to the previous/next folder
Search backward/forward.
Move cursor up/down.
Press
•
Start play or pause.
Confi rm selection.
i
USB socket
•
j SD/SDHC/MMC card slot
k AV IN
External equipment audio/video in
•
socket
l RESET
Reset the unit when it hangs up.
•
m
(red)
Terminate call.
•
n
(green)
Answer phone.
•
Dial number.
•
o SOURCE
Select source.
•
p
Turn the unit on or off.
•
Turn mute on or off.
•
Adjust volume.
•
q
•
Adjust screen brightness and contrast.
r
TILT
•
Adjust tilt of the screen.
Overview of the remote
control
}
}
|
|
{
{
z
z
y
y
x
x
w
w
v
v
u
u
t
t
s
s
a TILT
•
Adjust tilt of the screen.
b OPEN/CLOSE
•
Open or close the screen.
c SUBTITLE
•
Select DVD or DivX subtitle language.
d ANGLE
•
Select a difference angle/version of
the current DVD scene.
a
a
b
b
c
c
d
d
e
e
f
f
g
g
h
h
i
i
j
j
k
k
l
l
m
m
n
n
o
o
p
p
q
q
r
r
8
EN
e DISC AUDIO
•
Select audio language or audio
channel.
f
•
Change to wide screen display.
g REPT A->B
•
Set A-B repeat play.
h REPT
•
Select repeat play mode.
i
•
Return to previous menu or exit.
j VOLUME +/-
•
Adjust volume.
k EQ
•
Select equalizer (EQ) setting.
l
•
Mute or unmute audio.
m DISP
•
Display play information.
n CLEAR
•
Delete entered numbers.
o Numeric keypad
p
(green)
•
Answer phone.
•
Dial number.
q
(red)
•
Terminate call.
r SHUFF #
•
Turn random play on or off.
•
# symbol for phone call.
s INTRO *
•
Search for radio station and play the
station for 10 seconds, then search for
next station.
•
* symbol for phone call.
t AUDIO
•
Access audio setting menu.
u Navigation buttons
•
/
Tune for radio station.
Skip to previous/next track/chapter.
Move cursor to left/right.
•
/
Skip to the previous/next preset
station.
Skip to the previous/next folder.
Search backward/forward for DVD
video.
Move cursor up/down.
SEL
•
Start play or pause.
Confi rm selection.
v MENU
Access system menu
•
w GOTO
Select track/chapter.
•
x
•
Stop play.
y DISC MENU
•
Return to DVD main menu.
z
•
Adjust brightness/contrast.
{ SOURCE
Select source.
•
| TITLE
Access or exit DVD title menu.
•
}
PWR
•
Turn the unit on or off.
English
Your Car Entertainment System
EN
9
3 Get started
Caution
Use the controls only as stated in this user manual.•
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for
the model and serial number of your unit. The
model number and serial number are on the
bottom of your unit. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground (earth) 12 V
•
DC operation only.
•
Always install this unit in the car dashboard. Other
locations can be dangerous as the rear of the unit heats
up during use.
•
To avoid short-circuit: before you connect, ensure that
the ignition is off.
•
Ensure that you connect the yellow and red power
supply leads after all other leads are connected.
•
Ensure that all loose leads are insulated with electrical
tape.
•
Ensure that the leads do not get caught under screws
orin parts that will move (e.g. seat rail).
•
Ensure that all ground (earth) leads are run to a
common ground (earth) point.
•
Use only the supplied mounting hardware for a safe
and secure installation.
•
Improper fuses can cause damage or fi re. When you
need to change the fuse, consult a professional.
•
When you connect other devices to this
unit, ensure that the rating of the car circuit
is higher than the total fuse value of all the
connected devices.
Notes on speaker connection
•
Never connect speaker wires to the metal
body or chassis of the car.
•
Never connect speaker wires with stripes
to one another.
Overview of parts
These are the supplied parts needed to
connect and install this unit.
a
c
c
ba
b
ed
ed
a Trim plate x 2 pcs
b Standard connector
c Short mounting bracket x 2 pcs
d Rubber cushion
e Screws
- M5x16mm x 1 pc
- M4x3mm x 4 pcs
- M5x5mm x 2 pcs
- M5x5.5mm x 4 pcs
- M5x6mm x 1 pc
Note on the power supply lead (yellow)
10
EN
Connect wires: ISO connectors
Caution
Ensure that all loose leads are insulated with electrical
•
tape.
1 Pull out the ISO connectors from the car
dashboard and connect them to the bigger
end of the supplied standard connector.
2 Connect the other end of supplied
standard connector to the unit.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
0
0
!
!
Connector Connect to/with
1 Black cable Antenna
2 Yellow cable Video out 1
3 Yellow cable Video out 2
4 Yellow cable Camera in
5 Green/white
wire
6 Black cable Bluetooth
7 Blue cable Subwoofer
8 Red cable Front line out L
9 White cable Front line out R
10 Red cable Rear line out L
11 white cable Rear line out R
Parking (see
‘Connect parking
brake wire’ on page
14 )
microphone
English
Connect wires: ISO connectors
If necessary, connect the following:•
Connect wires: without ISO
connectors
Caution
Ensure that all loose leads are insulated with electrical
•
tape.
1 Cut off the bigger end of the supplied
standard connector.
EN
11
2 Check the car’s wiring carefully, then
connect them to the standard connector.
!
!
0
0
9
9
8
8
1
1
2
2
3
3
4
4
5
5
6
6
7
7
Connector Connect to
1 Blue/white
wire
2 Pink wire Reverse driving (see
3 Yellow wire The +12V car battery
4 Blue wire Amp. remote
5 Orange/
white wire
6 Black wire A metal surface of the
The electric antenna
control lead or power
supply lead of the
antenna booster
If there is no electric
antenna or antenna
booster, or it is manually
operated telescopic
antenna, it is not
necessary to connect
this lead.
‘Connect reverse
driving cable’ on page
14 )
which is live at all
times .
Illumination switch
car
First connect the black
ground (earth) lead,
then connect the yellow
and red power supply
leads.
12
EN
Loading...