Philips CED1910BT User Manual

Always there to help you

Question?

Contact

Philips

CED1910BT

User manual 1 Benutzerhandbuch 95 Gebruiksaanwijzing 195

Mode d’emploi 45 Manual del usuario 145 Manuale utente 245

English

Contents

1 Safety 3

2 Your car entertainment system 4

Introduction 4 What's in the box 4 Overview of the main unit 5 Overview of the remote control 6

3 Install the car entertainment system 7

Connect wires 8 Mount into the dashboard 11

4 Get started 12

Prepare the remote control 12 Turn on 12 Use the home menu 13 Set the date and time 14 Adjust the screen brightness 14 Switch display designs 15

5 Play from hard media 15

Load a disc 15 Connect a USB storage device 16 Insert an SD/SDHC card 16 Control play 16

Browse recorded les 18

About DivX® videos 18

6 Listen to radio 19

Switch to radio mode 19 Set up 19 Tune to a radio station 20 Store radio stations in memory 20 Tune to a preset radio station 21 Use RDS related features 21

7 Use the navigation system 22

Insert the map data card 22 Navigate your road trip 22

8 Use Bluetooth devices 23

Activate the Bluetooth function 23 Pair a device 23 Play audio from a connected device 25 Make a call 26

9 Play from an iPod/iPhone 28

Compatible iPod/iPhone models 28 Connect your iPod/iPhone 28 Control play 29 Charge your iPod/iPhone 29

10 Smart Connect Link 30

11 Universal USB Charging 30

12 Adjust sound 31

Adjust the volume level 31 Mute sound 31 Enable the MAX Sound effect 31 Enable the DBB sound effect 31 Enable the FullSound effect 31 Select a preset sound equalizer 31 Others 32

13 Adjust settings 33

Access system setup menus 33 Adjust general settings 34 View system information 34 Adjust Navigation settings 35 Adjust Bluetooth settings 35

14 Others 36

Play external audio/video input 36 Use rear monitors 36 Use buttons on the steering wheel 37 Reset the system 38 Replace the fuse 38

Upgrade the rmware 38

15 Product information 39

16 Troubleshooting 41

General 41 About the Bluetooth device 42

17 Notice 42

Compliance 42 Care of the environment 42 Trademark notice 43 Copyright 43

2 EN

English

1 Safety

Read and understand all instructions before you use the device. If damage is caused by failure to follow instructions, the warranty does not apply.

• Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

• The device is designed for negative ground (earth) 12 V DC operation only.

• To reduce the risk of trafc accidents, do

not watch video when driving.

• To ensure safe driving, adjust the volume to a safe and comfortable level.

• Improper fuses can cause damage or re. When you need to change the fuse,

consult a professional.

• Use only the supplied mounting hardware for a safe and secure installation.

• To avoid short circuits, do not expose the device, remote control or remote control batteries to rain or water.

• The device shall not be exposed to dripping or splashing.

• Do not place any sources of danger on the device (e.g. liquid lled objects, lighted

candles).

• Never insert objects into the ventilation slots or other openings on the device.

• Never place any objects other than discs into the disc tray/slot.

• To avoid exposure to laser radiation, do not disassemble the device.

• Risk of damage to the screen! Never touch, push, rub or strike the screen with any object.

• Never use solvents such as benzene, thinner, cleaners available commercially, or anti-static sprays intended for discs.

• Clean the device with soft, damp cloth. Never use substances such as alcohol, chemicals or household cleaners on the device.

• Risk of swallowing batteries! A coin type battery is bundled, which can be swallowed. Keep the battery out of reach of children at all times!

2 Your car

What's in the box

entertainment system

Congratulations on your purchase, and

welcome to Philips! To fully benet from the

support that Philips offers, register your product at www.philips.com/welcome.

Introduction

With the car entertainment system, you can

• listen to music,

• watch videos,

• view pictures,

• listen to FM (RDS included) and AM/MW

radio,

• make phone calls via Bluetooth, and

• navigate your road trip.

Check and identify the contents of the package:

ef g

4 EN

1 Main unit 2 Remote control 3 Rubber cushion 4 Screw X 4

(M5x8mm)

5 Hexagon head

screw

7 Use manual 8 Trim plate

6 Remote control

battery

English

Overview of the main unit

• Press to eject the disc.

• Press to access the navigation system.

• Access the the Smart Phone Mirror

Box (not supplied by Philips) via Smart Connect Link (refer to Chapter 10).

• Press to turn on the unit.

• Press and hold to turn off the unit.

• Press to mute the speakers or release

them from mute status.

d RESET

• Press to reset the system.

• Insert an SD/SDHC card.

f MAP

• Insert a microSD card that stores the digital map data.

g iR sensor

• The sensor that receives infra-red signals from the remote control.

h AV-IN

• Connect to the audio and video output sockets of an external player by a composite AV cable.

b c d

• Connect to a USB storage device or iPod/iPhone.

j LCD screen k +/-

• Press to increase or decrease the volume.

l MIC

• The built-in microphone for phone calls.

Overview of the remote control

x w v u

t s r q p o

n m

a SOURCE

• Press repeatedly to select a source.

• Press to eject the disc.

• Return to the previous menu or mode.

d VOLUME + / -

• Press to increase or decrease the volume.

• Access the home menu.

• Enable or disable the maximum sound.

• Switch to video playback mode.

• Enable or disable the FullSound effect.

b c

e f g h i j

k l

i DVD AUDIO

• Select an audio language or audio channel.

j DBB

• Enable or disable the DBB (Dynamic Bass Boost) sound effect.

k EQ

• Select a preset sound equalizer.

l MUSIC ZONE

• Select a music listening zone.

• Turn on or off the screen.

• Switch to the control interface for front source or rear source.

o TOP MENU

• Return to top menu.

p DVD MENU

• Access the DVD menu.

• Switch to music playback mode.

• Switch to picture slideshow mode.

• Start, pause, or resume the play.

t OK

• Conrm an option.

u / /TRACK -/TRACK +

• Skip to the previous or next track, chapter, or le.

• For DVD, press and hold to select a

speed for fast backward or forward search.

v BAND

• Select a tuner band.

w / /PRESET +/PRESET -

• Tune to the previous or next preset radio station.

• Skip to the previous or next folder.

6 EN

English

• Press to turn on the system.

• Press and hold to turn off the system.

• Press to mute the speakers or release

them from mute status.

y NAVI

• Press to access the navigation system.

3 Install the car

entertainment system

Always follow the instructions in this chapter in sequence.

These instructions are for a typical installation. However, if your car has different requirements, make the adjustment accordingly. If you have any question regarding installation kits, consult your local retailer.

Note

• This system is designed for negative ground (earth) 12V

DC operation only.

• Always install this system in the car dashboard. Other

locations can be dangerous as the rear of the system heats up during use.

• To avoid short-circuit: before you connect, make sure

that the ignition is off.

• Make sure that you connect the yellow and red power

supply leads after all other leads are connected.

• Make sure that all loose leads are insulated with

electrical tape.

• Make sure that the leads do not get caught under

screws iron parts that will move (e.g. seat rail).

• Make sure that all ground (earth) leads are run to a

common ground (earth) point.

• Use only the supplied mounting hardware for a safe

and secure installation.

• Improper fuses can cause damage or re. When you

need to change the fuse, consult a professional.

• When you connect other devices to this system, make

sure that the rating of the car circuit is higher than the total fuse value of all the connected devices.

• Never connect speaker wires to the metal body or

chassis of the car.

• Never connect speaker wires with stripes to one

another.

Connect wires

Note

• Make sure that all loose leads are insulated with

electrical tape.

• Consult a professional to connect wires as instructed

below.

• Before connection, check the car's wiring carefully.

2 Connect other wires if necessary.

1 Connect the ISO male connectors.

ISO male connectors Connect to

a Green strip, black-

edged green strip

White strip, blackedged white strip

c Gray strip, black-

edged gray strip

Purple strip, blackedged purple strip

e Red strip Ignition key +12V

f Blue strip Motor/electric

g Blue strip, white strip Amplier relay

h Black strip Ground i Yellow strip The +12V car

Rear left speaker

Front left speaker

Front right speaker

Rear right speaker

DC when ON/ACC

antenna relay control lead

control lead

battery which is energized at all times

Connectors and

sockets on rear panel

1 For ISO male

connectors

2 REAR OUT R (Red

socket)

3 AV-IN R(Red socket) Right audio

4 AV-IN L(White

socket)

5 REAR OUT L (White

socket)

6 VIDEO IN (Yellow

socket)

7 VIDEO OUT 1

(Yellow socket)

8 VIDEO OUT 2

(Yellow socket)

9 RADIO ANTENNA

(Green socket)

10 CAMERA IN (Purple

socket)

11 SUB-W OUT (Blue

socket)

12 REVERSE CAMERA

(Purple wire)

13 PARKING BRAKE

(Pink wire)

External sockets or connectors

As indicated above

Rear right speaker

channel output socket of an external player

Left audio channel output socket of an external player

Rear left speaker

Video output socket of an external player

Video input socket of an external display device

Radio antenna

Video output socket of an external camera

Sub-woofer

Reverse camera (B+)

Parking brake (-)

8 EN

English

Connectors and

sockets on rear panel

14 OE SWC IR

REMOTE IN (Brown wire)

15 OE SWC IR

REMOTE IN (Black wire)

16 OE SWC AD LEARN

(White wire)

17 OE SWC AD LEARN

(White wire)

18 OE SWC AD LEARN

(Black wire)

19 Smart Connect Link

Connector (Black connector)

20 External Mic (Black

connector)

21 GPS AERIAL (Black

connector)

22 FRONT OUT R (Red

connector)

23 FRONT OUT L

(White connector)

24 Rear Monitor

Audio Out 1 (white connector)

25 Rear Monitor

Audio Out 1 (Red connector)

26 Rear Monitor

Audio Out 2 (White connector)

27 Rear Monitor

Audio Out 2 (Red connector)

External sockets or connectors

OE SWC remote in

Ground

OE SWC AD Learn line 1

OE SWC AD Learn line 2

Ground

Compatible with external accessory box (refer to Chapter 10)

External microphone

GPS smart antenna

Front right speaker

Front left speaker

Left audio channel input socket of one rear monitor

Right audio channel input socket of one rear monitor

Left audio channel input socket of another rear monitor

Right audio channel input socket of another rear monitor

Tip

• The pin arrangement for the ISO connectors depends

on the type of your vehicle. To avoid damage to the system, connect properly.

z y x

w v

u t

r q

(Not Supplied)

10 EN

bcde fghijk

English

Mount into the dashboard

3 Slide the unit into the dashboard until a

click sound is heard.

Note

• Make sure that wires are correctly connected before

you mount the main unit into a car.

• If preset radio stations are lost when the ignition key

is turned OFF and then back ON, reconnect the red leads crosswise to the yellow ones.

1 If the car does not have an on-board drive

or navigation computer, disconnect the negative terminal of the car battery.

• If you disconnect the car battery in a car that has an on-board drive or navigation computer, the computer may lose its memory.

• If the car battery is not disconnected, to avoid short-circuit, make sure that bare wires do not touch each other.

2 Make sure that the car dashboard opening

is within these measurements:

5 mm

4 Reconnect the negative terminal of the car

battery.

182 mm

112 mm

• Since the unit cannot be used if the dashboard opening's slant angle is above 20 degrees, make sure that the horizontal slant of the car dashboard opening is between 0 and 20 degrees.

4 Get started

Caution

• Risk of car accidents! Never watch video or operate

this system while driving.

Prepare the remote control

1 Pull out the battery tray. 2 Insert one CR2025 battery with correct

polarity (+/-) as indicated.

3 Insert the battery tray.

Turn on

Press .

» PHILIPS logo and a progress bar are

displayed while boot-up.

• To turn off the system, press and hold for 3 seconds.

For the rst time use

Pull the protective sheet out.

» The remote control is ready for use.

Replace the battery

Caution

• Risk of explosion! Keep batteries away from heat,

sunshine or re. Never discard batteries in re.

Note

• Remove the battery if it is exhausted or if the remote

control is not to be used for a long time.

• Batteries contain chemical substances, they should be

disposed of properly.

• Perchlorate Material - special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate.

For the st time use

After successful boot-up, the following interface is displayed.

1 Tap to select a language for on-screen

display.

» The following interface is displayed.

12 EN

2 Tap to select a radio region that matches

your location.

» The following interface is displayed.

English

3 Tap [FINISH] to complete the initial setup.

» The device switches to radio mode

automatically.

Use the home menu

Note

• If is displayed when you touch an icon, it indicates

that the selected media or feature is unavailable at the current time.

Access the home menu

Tap to access the home menu.

» The clock, date, and the bar for

popular icons are displayed.

• To access the full menu with all feature icons displayed, tap .

• To return to the home menu, tap .

• [Radio]: Switch the source to FM/

AM radio.

• [Disc]: Switch the source to disc.

• [USB]: Switch the source to USB

storage device.

• [SDHC]: Switch the source to SD/ SDHC card.

• : Once your iPod/iPhone is connected and recognized, this icon is displayed in the bar of favorite icons. Tap it to switch the source back to iPod/iPhone.

• [Navigation]: Access the navigation system.

• [Bluetooth]: Use the Bluetooth feature.

• [AV-In 1]/[AV-In 2]: Switch the source to the audio and video input that is transferred from an external video player.

• R [Rear zone]: Access the settings for rear monitors.

• [SWC]: Access the interface to assign functions to buttons on the steering wheel.

• [Settings]: Access the system menu.

• [Car Mirror]: Access the the Smart

Phone Mirror Box (not supplied by Philips) via Smart Connect Link (refer to Chapter 10).

+ 31 hidden pages