Philips CE120X/78 Quick Start Guide

Register your product and get support at

CE120

1

2a

ENG Quick Start Guide

a

e

c

b

d

f

2b

9

1
2

8

3
4

7

6

g

All rights reserved.

© 2008 Koninklijke Philips Electronics N.V.

English

Overview of parts

These are the supplied parts needed to connect
and install this unit.

a Carry case with front panel stored inside
b Trim plate
c Standard connector
d Disassembly tool x 2 pcs
e Rubber cushion
f Screw x 4 pcs
g Mounting bolt

Connect wires: ISO connectors

1 Pull out the ISO connectors from car

dashboard and connect them to the bigger
end of the supplied standard connector.

2 Connect the other end of the supplied

standard connector to the unit.

3 Do the other connections, if applicable.

Antenna To antenna

1

Rear line out

2

(right)

Rear line out

3

(left)

To amplifi er line in (right)

To amplifi er line in (left)

Connect wires: without ISO
connectors

Cut off the bigger end of the supplied

1

standard connector.

Check the car’s wiring carefully and connect

2

them to the supplied standard connector.

Black To a metal surface of the car

1

Blue To the electric antenna control

2

Yellow To the +12V car battery which

3

Pink To telephone mute terminal (if

4

Red To the +12V power terminal

5

Green/

6

black
strip

White/

7

black
strip

Gray/

8

black
strip

Purple/

9

black
strip

First connect the black ground
(earth) lead, then connect the
yellow and red power supply
leads.

lead or power supply lead of the
antenna booster

If there is no electric antenna or
antenna booster, or it is manually
operated telescopic antenna, it
is not necessary to connect this
lead.

is energized at all times .

any) .

which is energized in the ac­cessory (ACC) position of the
ignition switch

If there is no accessor y position,
connect to the +12V car battery
terminal that is always live. Be
sure to connect the black ground
(earth) lead to a metal surface of
the car fi rst.

Left speaker (Rear)

Left speaker (Front)

Right speaker (Front)

Right speaker (Rear)

3 Connect the supplied standard connector to

the unit.

4 Do the other connections, if applicable.

Antenna To antenna

1

Rear line out

2

(right)
Rear line out

3

(left)

To amplifi er line
in (right)

To amplifi er line
in (left)

Attach the front panel

Attach the trim plate.

1

Insert the left side of the panel in the chassis

2

until it is correctly engaged.

Press the right side of the panel until it is

3

locked into place.

Mount into the dashboard
1 Ensure that car dashboard opening is within

these measurements:

•

If the car dashboard is bigger, the sup­plied mounting sleeve is not suitable for
the car. Remove the mounting sleeve
with the removal keys and consult a
professional for advice.

2 If the car does not have an on-board drive

or navigation computer, disconnect the nega­tive terminal of the car attery.

If you disconnect the car battery in

•
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
If the car battery is not disconnected,

•
to avoid short-circuit, ensure that bare
wires do not touch each other.

Connect the supplied mounting bolt to the

3

unit.

Place the supplied rubber cushion over the

4

end of the mounting bolt.

Slide the unit into the dashboard until you

5

hear a click sound.=

Reconnect the negative terminal of the car

6

battery.

Detach the front panel

You can detach the front panel to deter theft.

Press

1

Pull the panel towards you to detach it from

2

Store the panel in the supplied carry case to

3

to release the panel.

the chassis.

protect it from dirt or damage.

Turn on

1

Press to turn on the unit.

To turn off the unit, press

•
seconds.

for 3

Set clock
1

Press MENU / DISP for 3 seconds.

2 Press DBB or SEARCH repeatedly until

the currently clock is displayed.

3 Tur n in clockwise direction to set hour.

Tu r n in anti-clockwise direction to set
minute.

4 Press to confi rm.

View clock
1

Press MENU / DISP repeatedly until the clock

is displayed.

Tune to a radio station

Press SOURCE to select Tuner.

1
2 Press DBB or SEARCH to select band:

[FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .

3 Press LOC/DX to select tuner sensitivity:

[LOCAL] (local): Only station with strong
signal can be broadcast.
[DX] (distance): Stations with strong and
weak signals can be broadcast.

4 Press or to tune to a radio station

manually.

The radio station is broadcast.

»

•

To search for radio station automatically,
press

or for 3 seconds.

5

Insert USB device

1 Open the cover marked

panel.

Inser t the USB device into the USB socket.

2

The unit starts playing from the USB

»

device automatically.

Insert SD/MMC card

Open the cover marked

1

panel.

Insert the SD or MMC card into the card

2

slot.

The unit starts playing from the SD/MMC

»

card automatically.

on the front

on the front

Control play

To select a folder, press DBB or SEARCH

•
.

To skip to a track, press

•

•

To search within a track, press
3 seconds.
To pause, press 1 ,

•

again.

or .

or for

. To resume, press 1 ,

123

3

4

5

5 mm

183 mm

52mm

6

English

Overview of parts

These are the supplied parts needed to connect
and install this unit.

a Carry case with front panel stored inside
b Trim plate
c Standard connector
d Disassembly tool x 2 pcs
e Rubber cushion
f Screw x 4 pcs
g Mounting bolt

Connect wires: ISO connectors

1 Pull out the ISO connectors from car

dashboard and connect them to the bigger
end of the supplied standard connector.

2 Connect the other end of the supplied

standard connector to the unit.

3 Do the other connections, if applicable.

Antenna To antenna

1

Rear line out

2

(right)

Rear line out

3

(left)

To amplifi er line in (right)

To amplifi er line in (left)

Connect wires: without ISO
connectors

Cut off the bigger end of the supplied

1

standard connector.

Check the car’s wiring carefully and connect

2

them to the supplied standard connector.

Black To a metal surface of the car

1

Blue To the electric antenna control

2

Yellow To the +12V car battery which

3

Pink To telephone mute terminal (if

4

Red To the +12V power terminal

5

Green/

6

black
strip

White/

7

black
strip

Gray/

8

black
strip

Purple/

9

black
strip

First connect the black ground
(earth) lead, then connect the
yellow and red power supply
leads.

lead or power supply lead of the
antenna booster

If there is no electric antenna or
antenna booster, or it is manually
operated telescopic antenna, it
is not necessary to connect this
lead.

is energized at all times .

any) .

which is energized in the ac­cessory (ACC) position of the
ignition switch

If there is no accessor y position,
connect to the +12V car battery
terminal that is always live. Be
sure to connect the black ground
(earth) lead to a metal surface of
the car fi rst.

Left speaker (Rear)

Left speaker (Front)

Right speaker (Front)

Right speaker (Rear)

3 Connect the supplied standard connector to

the unit.

4 Do the other connections, if applicable.

Antenna To antenna

1

Rear line out

2

(right)
Rear line out

3

(left)

To amplifi er line
in (right)

To amplifi er line
in (left)

Attach the front panel

Attach the trim plate.

1

Insert the left side of the panel in the chassis

2

until it is correctly engaged.

Press the right side of the panel until it is

3

locked into place.

Mount into the dashboard
1 Ensure that car dashboard opening is within

these measurements:

•

If the car dashboard is bigger, the sup­plied mounting sleeve is not suitable for
the car. Remove the mounting sleeve
with the removal keys and consult a
professional for advice.

2 If the car does not have an on-board drive

or navigation computer, disconnect the nega­tive terminal of the car attery.

If you disconnect the car battery in

•
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
If the car battery is not disconnected,

•
to avoid short-circuit, ensure that bare
wires do not touch each other.

Connect the supplied mounting bolt to the

3

unit.

Place the supplied rubber cushion over the

4

end of the mounting bolt.

Slide the unit into the dashboard until you

5

hear a click sound.=

Reconnect the negative terminal of the car

6

battery.

Detach the front panel

You can detach the front panel to deter theft.

Press

1

Pull the panel towards you to detach it from

2

Store the panel in the supplied carr y case to

3

to release the panel.

the chassis.

protect it from dirt or damage.

Turn on

1

Press to turn on the unit.

To turn off the unit, press

•
seconds.

for 3

Set clock
1

Press MENU / DISP for 3 seconds.

2 Press DBB or SEARCH repeatedly until

the currently clock is displayed.

3 Tur n in clockwise direction to set hour.

Tu r n in anti-clockwise direction to set
minute.

4 Press to confi rm.

View clock
1

Press MENU / DISP repeatedly until the clock

is displayed.

Tune to a radio station

Press SOURCE to select Tuner.

1
2 Press DBB or SEARCH to select band:

[FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .

3 Press LOC/DX to select tuner sensitivity:

[LOCAL] (local): Only station with strong
signal can be broadcast.
[DX] (distance): Stations with strong and
weak signals can be broadcast.

4 Press or to tune to a radio station

manually.

The radio station is broadcast.

»

•

To search for radio station automatically,
press

or for 3 seconds.

Insert USB device

1 Open the cover marked

panel.

Inser t the USB device into the USB socket.

2

The unit starts playing from the USB

»

device automatically.

Insert SD/MMC card

Open the cover marked

1

panel.

Insert the SD or MMC card into the card

2

slot.

The unit starts playing from the SD/MMC

»

card automatically.

on the front

on the front

Control play

To select a folder, press DBB or SEARCH

•
.

To skip to a track, press

•

•

To search within a track, press
3 seconds.
To pause, press 1 ,

•

again.

or .

or for

. To resume, press 1 ,

4.75-5.56 mm

183 mm

7

52mm