Philips C2 Series, Lightolier C2 Series, Lightolier cLRT Specification

C2 Series

Recessed Emergency Lighting

Page 1 of 2

C2125L2RT6

12. 0"

(30.5 cm)

4.4"

(11.3 cm)

6.0"

(15.2 cm)

24.0"

(61.0 cm)

15.6"

(38.7 cm)

Features

Illumination: Illumination

is provided by up to four

adjustable lamp heads. Choose

from round or rectangular

thermoplastic heads with

Par 36 sealed beam tungsten

or halogen, or wedge base

tungsten or halogen lamps.

Lamp heads are factory

installed. The suggested head

is Lightolier’s “R” series wedge

base tungsten round lamp

head.

Housing: Faceplate

constructed of 18 gauge steel

with a white epoxy powder

coat finish; backbox 20 gauge

steel. Up to four lamp heads

can be mounted on the unit

faceplate. Lamp head choices

include round or rectangular

white thermoplastic to match

housing. Designed for easy,

drop-in installation into

suspended ceilings. Additional

wire supports may be required

by local codes and are supplied

by others.

Operating Temperature

Range: Standard Location

65°F (19°C) to 85°F (30°C)

Electronics: 120/277 VAC

dual voltage input with surge-

protected, solid-state charging

circuitry provides for a reliable

charging system. Charging

system is complete with

low voltage disconnect, AC

lockout, brownout protection,

AC indicator lamp and test

switch.

Electrical Specifications:

0.150 A, 18 W max. (120 VAC)

0.065 A, 18 W max. (277 VAC)

Code Compliance

UL 924 listed. NFPA 101,

NEC, BOCA, OSHA and IBC

illumination standards. Chicago

Approved City Plan No. 1879E.

Warranty

Three year full electronics

warranty. One year full plus

four year prorated lead calcium

battery warranty. Five year full

plus five year prorated nickel

cadmium battery warranty.

Job Information Type:

Job Name:

Cat. No.:

Notes:

Recessed Emergency Lighting

Ordering Information

C2

Series

C2 = Recessed
Emergency
Lighting Unit

Note

1) Some option combinations may impact UL listing. Consult factory for specifics.

2) 15 minute delay.

DC Voltage

1 = 6 V
2 = 12 V

Battery

6 V Lead Calcium

25L = 25 W Unit
50L = 50 W Unit

6 V Nickel Calcium

14N = 14 W Unit
25N = 25 W Unit

12 V Lead Calcium
50L = 50 W Unit

12 V Nickel Calcium

25N = 25 W Unit
50N = 50 W Unit

# of Heads

1= One
2 = Two
3= Three
4 = Four
Blank= No

Heads

Lamp Heads

6V Round Wedge Base

RT6 = 5.4 W Tungsten
RT7 = 7.2 W Tungsten
RT9 = 9 W Tungsten
RH7 = 7 W Halogen
RH10 = 10 W Halogen
RH12 = 12 W Halogen

12V Round Wedge Base

RT9 = 9 W Tungsten
RT12 = 12.5 W Tungsten
RT18 = 17.9 W Tungsten
RH12 = 12 W Halogen

C2 Series

Factory Installed Options

T1 = 120 VAC Time Delay
T2 = 277 VAC Time Delay
V = Voltmeter
A = Ammeter
F1 = 120 VAC Fuse
F2 = 277 VAC Fuse
P1 = 120 VAC Power Switch
P2 = 277 VAC Power Switch

1

2

2

Page 2 of 2

Optics

Wall mounted 10' AFF, ‘RH12’ 6 V 12 W Halogen Lamps Represented

1 FC Average

10 ft.

.8 .8 .8 .9 .9 .8 .8 .7 .7 .7 .7 .8 .9 .9 .9 .8 .8 .8

1.0 1.1 1.2 1. 3 1.3 1.2 1.0 .9 .8 .8 .9 1.1 1.2 1.3 1.3 1. 2 1.0 1.0

1.1 1.2 1.4 1. 5 1.5 1.4 1.2 1.0

1.2 1. 2 1.5 1.6 1.6 1.4 1.2 1.0

1.0 1.0 1.1 1.2 1.3 1. 2 1.0 .9 .8 .8 .9 1.0 1.2 1.3 1.2 1. 2 1.1 1.0

.8 .8 .9 .9 .9 .9 .8 .7 .7 .7 .7 .8 .9 .9 .9 .9 .8 .8

Average initial footcandles at floor = 1.05

.9 .9

.9 .9

(fixture spacing)

1.0 1.2 1.4 1.5 1.5 1.4 1.2 1.1

1.0 1.2 1.4 1.6 1.6 1.5 1.3 1.2

18 ft.

6 ft.

Maximum initial footcandles at floor = 1.6

Minimum initial footcandles at floor = 0.7

Maximum to minimum ratio = 2.29

* The optics layout shown is intended to be used as reference only. Standard reflectances used were 80/50/20. Lightolier is not responsible for site specific conditions that
may alter the results.

Philips Lightolier
e: [e-mail]
t: [phone]
w: www.lightolier.com

C2 Series May 29, 2012

Specifications are subject to change without notice.
© Koninklijke Philips Electronics N.V., 2012. All rights reserved.

Job Information Type: