Philips AZ-5150 Service manual
Handling Chip Components and Safety ..........................1 - 1
Technical Specification & Service tools...........................2 - 1
Service Measurement......................................................2 - 2
Connections and controls.....................................3 - 1 to 3- 2
Instructions for Use .............................................3 - 3 to 3 - 8
Disassembly Diagram......................................................4 - 1
Pin-description of ICs..........................................4 - 2 to 4 - 5
Block Diagram .................................................................5 - 1
Wiring Diagram................................................................6 - 1
Tuner Board
Circuit Diagram........................................................7 - 1
Layout Diagram.......................................................7 - 2
Tuner Adjustment....................................................7 - 2
Main Board
Circuit Diagram .......................................................8 - 1
Layout Diagram ......................................................8 - 2
Cassette Board
Circuit Diagram........................................................9 - 1
Layout Diagram.......................................................9 - 2
VCD Board
Circuit Diagram......................................................10 - 1
Layout Diagram
Copper side view................................................10 - 2
Component side view.........................................10 - 3
Exploded Views Diagram
Cabinet ..............................................................11 - 1
Tape Deck .........................................................11 - 2
Mechanical Partslist.......................................................11 - 2
Electrical Partslist............................................12 - 1 to 12 - 2
© 3140 785 32170
Published by LX 0234 Service Audio Printed in The Netherlands Subject to modification
VCD MP3 CD Soundmachine
CLASS 1
LASER PRODUCT
AZ 5150
all versions
TABLE OF CONTENTS
©
Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
or otherwise without the prior permission of Philips.
VIDEO CD
HANDLING CHIP COMPONENTS
© WARNING
All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handling during
repair can reduce life drastically.
When repairing, make sure that you are connected with the
same potential as the mass of the set via a wristband with
resistance. Keep components and tools at this potential.
f ATTENTION
Tous les IC et beaucoup d´autres semi-conducteurs sont
sensibles aux décharges statiques (ESD). Leur longévite
pourrait être considérablement écourtée par le fait qu´aucune
précaution nést prise à leur manipulation.
Lors de réparations, s´assurer de bien être relié au même
potentiel que la masse de l´appareil et enfileer le bracelet
serti d´une résistance de sécurité.
Veiller à ce que les composants ainsi que les outils que l´on
utilise soient également à ce potentiel.
d WARNUNG
Alle ICs und viele andere Halbleiter sind empfindlich
gegenüber elektrostatischen Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kann die
Lebensdauer drastisch reduzieren.
Sorgen Sie dafür, daß Sie im Reparaturfall über ein Puls-
armband mit Widerstand mit dem Massepotential des
Gerätes verbunden sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls auf diesem
Potential.
ñ WAARSCHUWING
Alle IC´s en vele andere halfgeleiders zijn gevoelig voor
electrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan de levensduur
drastisch doen vermindern. Zorg ervoor dat u tijdens reparatie
via een polsband met weerstand verbonden bent met hetzelfde
potentiaal als de massa van het apparaat.
Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.
i AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono sensibili alle scariche
statiche (ESD).
La loro longevità potrebbe essere fortemente ridatta in caso di
non osservazione della più grande cauzione alla loro
manipolazione. Durante le riparationi occorre quindi essere
collegato allo stesso potenziale che quello della massa
delápparecchio tramite un braccialetto a resistenza.
Assicurarsi che i componenti e anche gli utensili con quali si
lavora siano anche a questo potenziale.
©
Safety regulations require that the set be restored to its
original condition and that parts which are identical with
those specified be used.
Safety components are marked by the symbol
i
Le norme di sicurezza estigono che l´apparecchio venga
rimesso nelle condizioni originali e che siano utilizzati i
pezzi di ricambiago identici a quelli specificati.
Componenty di sicurezza sono marcati con
ñ
Veiligheidsbepalingen vereisen, dat het apparaat in zijn
oorspronkeliijke toestand wordt teruggebracht en dat
onderdelen, identiek aan de gespecificeerde, worden toegepast.
De Veiligheidsonderdelen zijn aangeduid met het symbool
s Varning !
Osynlig laserstrålning när apparaten är öppnad och
spärren är urkopplad. Betrakta ej strålen.
∂ Advarsel !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere
er ude af funktion. Undgå udsaettelse for stråling.
ß Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen !
f
"Pour votre sécurite, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
ESD
SAFETY
d
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Originalzustand des Gerätes
darf nicht verändert werden. Für Reparaturen sind Original-
ersatzteile zu verwenden.
Sicherheitsbauteile sind durch das Symbol markiert.
f
Les normes de sécurité exigent que l`appareil soit remis
à l`état d`origine et que soient utilisées les pièces de
rechange identiques à celles spécifiées.
Les composants de sécurité sont marqués
CLASS 1
LASER PRODUCT
©
DANGER: Invisible laser radiation when open.
©
After servicing and before returning the set to customer
perform a leakage current measurement test from all
exposed metal parts to earth ground, to assure no
shock hazard exists.
The leakage current must not exceed 0.5mA.
AVOID DIRECT EXPOSURE TO BEAM.
1 - 1
GENERAL
Mains voltage :
-/01 120/230 V
Mains frequency :
-/01 : 50 / 60 Hz
Battery mains : 9 V (R14 x 6)
Power consumption : 22 W
Dimension (W x H x D) : 395 x
155 x 240 mm
Weight : 3.1 Kg
AMPLIFIER
Output power mains : 2 x 1 W
battery : 2 x 1 W
Speaker impedance : 2 x 8 ohm
Frequency response : 70 Hz - 3 kHz (±3dB)
TUNER - FM SECTION
Tuning range : 87 - 108.5 MHz
IF frequency : 10.7 MHz
Sensitivity : < 22 dB at 26dB S/N
Selectivity : > 20 dB at ±300kHz
±0.2MHz
IF rejection : > 50 dB
Image rejection : > 20 dB
TUNER - MW SECTION
Tuning range : 520 - 1630 kHz
IF frequency : 455 kHz ± 3 kHz
Sensitivity : < 4000 µV/m at 26dB S/N
Selectivity : 16 dB
:
IF rejection ratio 24 dB
:
Image rejection ratio 28 dB
AUDIO CASSETTE RECORDER
Number of tracks : 1 stereo
Tape speed : 4.76 cm/sec ± 3%
Wow & flutter : < 0.35 % JIS UWTD
Fast wind/rewind C60 : < 130 sec.
Frequency response P/B : 125 - 8000 Hz
S/N ratio : > 36 dB
>
>
>
COMPACT DISC
:
S/N ratio > 45 dB
Channel difference 1 kHz : < 3 dB
Channel crosstalk 1 kHz : > 26 dB
Laser wavelength : 780 ± 20nm
Laser light power : < 0.3 mW
2 - 1
SERVICE TOOLS
Audio signal disc SBC 429.......................................................................4822 397 30184
Playability test disc SBC 444
...................................................................4822 397 30245
Test disc 5 (disc without errors ) +
Test disc 5A (disc with dropout errors, black spots and fingerprints)
SBC 426/426A.....................................................................4822 397 30096
Burn in test disc (65 min. 1kHz signal at -30 dB level without “pause”)
.....4822 397 30155
anti-static table mat
large 1200x650x1.25mm 4822 466 10953
small 600x650x1.25m 4822 466 10958
anti-static wristband
4822 395 10223
connection box (3 press stud connections, 1MΩ) 4822 320 11307
extendible cable (2m, 2MΩ, to connect wristband to connection box) 4822 320 11305
connecting cable (3m, 2MΩ, to connect table mat to connection box) 4822 320 11306
earth cable (1MΩ, to connect any product to mat or to connection box) 4822 320 11308
KIT ESD3 (combining all 6 prior products - small table mat) 4822 310 10671
wristband tester 4822 344 13999
AVAILABLE ESD PROTECTION EQUIPMENT
TECHNICAL SPECIFICATIONS
2 - 2
SERVICE MEASUREMENT
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Tuner SW
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday«s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
Ri=50Ω
Aerial replacement
Capacitor
R=50Ω
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
S/N and distortion meter
e.g. Sound Technology ST1700B
Frame aerial
e.g. 7122 707 89001
Tuner AM (MW,LW)
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday«s cage.
RF Generator
e.g. PM5326
Ri=50Ω
Low pass filter 22kHz
L
R
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
DUT
CD
Use Audio Signal Disc SBC429 4822 397 30184 (replaces test disc 3)
L.P.F. = 13
th
order filter 4822 395 30204
3 - 1
RECORD
P
L
A
Y
S
E
A
R
C
H
S
T
O
P
-
O
PE
N
P
AU
S
E
AZ5150
VCD/MP3-CD PLAYBACK
V
C
D
/
M
P
3
-
C
D
S
O
U
N
D
M
A
C
H
I
N
E
STO
P
S
E
A
R
C
H
P
L
A
Y
¥
P
A
US
E
SHUFFLE/
REPEAT
PROGRAM
SHUFFLE
B
AN
D
FM
L
W
M
W
T
U
NN
I
N
G
M
H
z
k
H
z
k
H
z
1
7
5
2
0
0
2
2
5
2
5
0
2
8
0
9
2
8
8
9
6
1
0
0
1
0
4
1
0
8
¥
F
M
¥
L
W
¥
M
W
P
O
W
E
R
V
O
L
U
M
E
D
B
B
D
Y
N
A
MI
C
B
A
S
S
B
O
O
S
T
1
5
0
6
3
0
8
0
0
1
0
0
0
1
3
0
0
1
6
0
0
5
3
0
PR
EV
N
EX
T
2
4
5
6
7
! 9
8
$
0
AC MAINS
1
3
@#
%
^
&
*
(
)
¡
MP3 General Information
English
Dear Customer,
Thank you for buying the Philips MP3-CD Soundmachine. Your great new acquisition will allow you to
listen to up to 10 hours of CD-like quality music, using the revolutionary new music compression
technology MP3.
MP3 technology
MP3 is short for MPEG1 Layer-3 encoding and decoding technology, a very powerful encoding
algorithm with which you can shrink down the orginal Digital Audio sound data with a factor of up to
10 without losing significant sound quality.
Recording and Playback
It is recommended to set your recording bit rate to 128Kbps, sampling frequency at 44.1KHz to
achieve CD-like music playback quality.
Since downloading MP3 files from the Internet, ripping songs from your own legal CD’s and burning
MP3 songs onto a CD-R, are a delicate process, the quality of a MP3 song may vary by these process.
Subsequently, making a MP3-CD may not be entirely perfect.
As a result of the above imperfection, you may experience an occasional “skip” while
listening, or an occasional delay in accessing “previous/next” title to MP3-CD’s. This is
considered to be normal.
A comparison chart is enclosed as below:
Sound Bit Rate Approximate Approximate total Comment
Quality Reduction Ratio MP3-CD time
AM radio 32 kbps 40 : 1 40 hrs Sound quality significantly
FM radio 64 kbps 20 : 1 20 hrs affected-not recommended.
Near-CD 96 kbps 15 : 1 15 hrs Balanced sound quality
CD-like 128 kbps 10 : 1 10 hrs compression rate.
CD 256 kbps 5 : 1 5 hrs Compression rate low
CD 320 kbps 3 : 1 3 hrs suggest to play CDs instead.
1
2
CONNECTIONS AND CONTROLS
3 - 2
CONTROLS
English
VOLUME - to adjust volume level.
DBB (Dynamic Bass Boost) - : for a more
vivid bass response.
Source selector - POWER ON/OFF switch and
to select source of sound source: DISC- TAPE -
RADIO.
LIFT TO OPEN - to open the CD door.8Band selector - to select FM/MW wave band
Tuning dial pointer
5
TUNING - to tune to radio stations
PROGRAM - to program track numbers and to
review the program.
6
REMOTE SENSOR - infrared sensor for
remote control
9
LCD Display - to show the CD, VCD, MP3
functions.
PLAY•PAUSE - To start or interrupt
CD playback.
STOP - to stop playback.
SEARCH or - to skip or search a passage
or a track
Cassette compartment
Cassette keys:
PAUSE - to interrupt recording or playback.
STOP•OPEN - To stop the tape and to
open the cassette holder.
SEARCH or - to fast wind/rewind the
tape.
PLAY - to start playback.
RECORD
0
- to start recording.
^ Battery door - to open the battery
compartment
&
COLOUR SYSTEM selector
-
to switch the
PAL or NTSC system.
Telescopic aerial - to improve radio
reception)VIDEO/AUDIO OUT - connect to the TV or
VCR VIDEO/AUDIO IN
AC MAINS - socket for mains lead
PHONES
- 3.5 mm stereo headphone socket
Remote Control
. . . . . . . . . . . . . . . . . . . .1 pc
Mains Cord
. . . . . . . . . . . . . . . . . . . . . . .1 pc
Audio / Video Cable
. . . . . . . . . . . . . . . .1 pc
SUPPLIED ACCESSAORIES
BACK PANEL
TOP AND FRONT PANEL
1
2
/
∞
§
;
;
9
1
2
3
456
7
9
0
!
@
#
$
%
*
(
¡
REMOTE CONTROL
English
PBC (PLAYBACK CONTROL) - to switch on or
off PBC mode (for VCD version 2.0 only).
2
RETURN - to return to the previous MENU level
during playback (for VCD with PBC on).
VIEW - to scan through a VCD with 9 pictures
display on TV screen. Only when PBC mode is
switched off (for VCD operation only).
OSD - to switch on/off the on screen display on
the TV screen.
SLOW - to watch a VCD at a slower speed (for
VCD operation only).
RESUME -.to resume playback in stop mode.
GOTO - to start playback at any chosen time on
the disc (for CD/VCD operation only).
PROG
for CD/VCD/MP3-CD . . . to programme disc
tracks.
REPEAT
for MP3-CD only . . . . . . . to repeat a track, an
album or whole disc.
for CD/VCD . . . . . . . . . . . to repeat a disc track
or the whole disc.
A - B -.to playback a certain scene or passage
repeatedly (for CD/VCD operation only).
ZOOM
for VCD only . . . . . . . to zoom in or zoom out .
SHUFFLE - When in CD/VCD mode, press to
start or stop shuffle play mode.
NTSC/PAL - to select the video output for
NTSC or PAL system.
R/L - to select MONO LEFT / MONO RIGHT /
STEREO.
DIGITS 0 - 9, +10
for CD/VCD/MP3-CD . . . to select a track
number.
PLAY/PAUSE
for CD/VCD/MP3-CD . . . to start or interrupt
playback.
&
ALBUM
for MP3-CD only . . . . to select previous / next
album
for CD/VCD . . . . . . . . to skip to the
previous/next track.
*
TITLE
for MP3-CD only . . . . to select previous/next
title.
for CD/VCD . . . . . . . . to search backward/
forward track.
(
STOP
for CD/VCD/MP3-CD . . . to stop playback or to
clear a programme.
REMOTE CONTROL
123
456
789
0
R/L
PBC
NTSC/PAL
RETURN
SLOW
VIEW
RESUME
OSD
GO TO
PROG
REPEAT
SHUFFLE
VIDEO CD
10
A B
ZOOM
ALBUM
PLAY
TRACK
PLAY
PLAY
AZ5150 VCD MP3 CD SOUNDMACHINE
6
4
7
3
5
9
0
!
3
1
3
4
5
6
7
8
9
0
!
@
#
$
%
^
21#
$
%
^
&
*
(
8
@
9
2
∞
§
;
J K
CONNECTIONS AND CONTROLS
3 - 3
POWER SUPPLY
English
Whenever convenient, use the mains supply if you want to conserve battery life. The battery supply
will be switched off when the set is connected to the mains.
Make sure you remove the plug from the
set and wall outlet before inserting batteries.
Batteries
1.
Open the battery compartment and insert six batteries, type
R-20, UM-1 or D-cells, (preferably alkaline) with the correct
polarity as indicated by the "
+" and "-" symbols inside the
compartment.
Remote control
Open the battery compartment and insert two batteries,
type AAA, R03 or UM4 (preferably alkaline).
2.
Replace the compartment door, making sure the batteries are
firmly and correctly in place.
3.
Remove the batteries if they are exhausted or if they will not be
used for a long period.
– The incorrect use of batteries can cause electrolyte leakage and
will corrode the compartment or cause the batteries to burst. Therefore:
– Do not mix battery types, e.g. alkaline with zinc carbonate.
–When inserting new batteries, replace all at the same time.
– Remove the batteries if the set is not to be used for a long time.
Note :
The battery supply is switched off when the set is connected to the mains.
Batteries contain chemical substances, so they should be disposed of properly
1.
Check if the mains voltage as shown on the type plate (on the
bottom of the set) corresponds to your local mains voltage. If it
does not, consult your dealer or service organisation.
2.
Connect the mains lead to the
AC
~
MAINS
socket and the wall
socket.
The set is now ready for use.
3.
To switch off the mains supply completely, pull the mains plug
out of the wall socket.
Disconnect the mains lead when you change over to battery supply, or to protect the set
during heavy thunderstorms.
The type plate is located on the bottom of the set.
MAINS
BATTERIES (NOT SUPPLIED)
CAUTION
Use of controls or adjustments or performance of procedures other than herein
may result in hazardous radiation exposure or other unsafe operation.
GENERAL OPERATION
English
1.
To switch on the set, adjust the source selector.
– The POWER indicator lights up.
2.
Adjust the sound using the VOLUME and DBB controls.
3
To switch off the radio, adjust the source selector to the
TAPE/
POWER OFF position, with the cassette keys released.
– The POWER indicator goes out.
1
Set the source selector to RADIO.
– The POWER indicator lights up.
2.
Adjust the sound using the VOLUME controls and the DBB
switch.
3.
Select the wave band using the BAND selector.
4.
Tune to a radio station using the TUNING knob.
– For FM, pull out the telescopic aerial. To improve FM-reception,
incline and turn the aerial. Reduce its length if the FM-signal is
too strong (very close to a transmitter).
– For MW, the set is provided with a built-in aerial, so the
telescopic aerial is not needed. Direct the aerial by turning
the whole set.
5.
To switch off, set the source selector to the TAPE/
POWER OFF
position (with the cassette keys released).
– The POWER indicator goes out.
R
E
C
O
R
D
P
L
A
Y
S
E
A
R
CH
S
T
O
P
-
O
P
E
N
P
A
U
S
E
A
Z
5
1
5
0
V
C
D
/M
P
3
-C
D
P
L
A
YB
A
C
K
V
C
D/M
P
3
-
C
D
S
O
U
NDM
A
C
H
IN
E
S
T
O
P
S
E
A
R
C
H
PL
A
Y
¥
P
A
U
SE
S
H
U
F
F
LE
/
R
E
P
EA
T
P
R
O
G
R
A
M
S
H
U
F
F
LE
B
A
N
D
F
M
L
W
M
W
T
U
N
N
I
N
G
M
H
z
k
H
z
k
Hz
1
7
5
2
0
0
2
2
5
2
5
0
2
8
0
9
2
8
8
9
6
1
0
0
1
0
4
1
0
8
¥
FM
¥
L
W
¥
M
W
P
O
W
E
R
V
O
L
U
M
E
D
B
B
D
Y
N
A
M
I
C
B
A
S
S
B
O
O
S
T
1
5
0
6
3
0
8
0
0
1
0
0
0
1
3
0
0
1
6
0
0
5
3
0
P
R
E
V
N
E
X
T
R
E
C
O
R
D
P
LAY
S
E
A
R
C
H
S
T
O
P
-
O
P
E
N
P
A
US
E
A
Z
5
1
5
0
V
CD
/M
P
3
-C
D
P
L
AY
B
A
CK
V
C
D
/M
P
3
-
C
D
S
OU
N
D
M
A
C
H
I
N
E
S
TO
P
S
E
AR
C
H
P
L
A
Y
¥
P
A
U
S
E
SH
U
F
F
L
E
/
R
E
P
E
A
T
P
R
O
G
R
A
M
S
H
U
F
F
L
E
B
A
N
D
F
M
L
W
M
W
T
U
N
N
I
N
G
M
H
z
k
H
z
k
H
z
1
7
5
2
0
0
2
2
5
25
0
2
8
0
9
2
8
8
9
6
1
0
0
1
0
4
1
0
8
¥
F
M
¥
L
W
¥
M
W
P
O
W
E
R
V
O
L
U
M
E
D
B
B
D
Y
N
A
M
I
C
B
A
S
S
B
O
OS
T
1
5
0
6
3
0
8
0
0
1
0
0
0
1
3
0
0
1
6
0
0
5
3
0
P
R
E
V
N
E
X
T
RADIO RECEPTION
S
TO
P
PAUSE
P
O
V
O
L
U
M
E
D
BB
D
Y
N
A
M
IC
B
A
S
S
B
O
O
S
T
GENERAL OPERATION
Environmental information
All unnecessary packaging material has been omitted. We have done our utmost to make the
packaging easily separable into three mono materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a specialized
company. Please observe the local regulations regarding the disposal of packaging
materials, exhausted batteries and old equipment.
™
™
INSTRUCTIONS FOR USE
3 - 4
CD/VCD/MP3-CD
English
IMPORTANT!
The CD part of this system also serves as a Video CD player if you connect it to your TV
set.
Before viewing the Video CD, ensure that the set is switched to corresponding PAL or
NTSC system of your TV set (exception Multi-system TV).
This set can playback all digital audio CD, video CD, finalised
digital audio CD-Recordable (CDR) discs and finalised digital audio
CD-Rewritable (CDRW) discs.
Support following MP3-CD formats:
•
ISO 9660 format - Max. 17 characters
•
Max. Track number plus Album is 256
•
Max. nested directory is 8 levels
•
The max. ALB number is 99
•
The max. MP3 programme track number is 99
•
The max. length of each track is 255 minutes 59 seconds
•
The player can play mixed mode disc:
a: MP3 + CDDA can only play the MP3 tracks in the first block.
b: VCD + CDDA full support
•
Supported VBR bit-rate
•
Supported sampling frequencies for MP3 disc : 32 kHz, 44.1 kHz, 48 kHz
•
Supported Bit-rates of MP3 disc are: 32, 64, 96, 128, 192, 256 (kbps)
Following formats are not supported
•
The files like *.WMA, *AAC, *.DLF, *.M3U, *.PLS
•
Chinese filename
•
The non-session closed discs
•
The discs recorded under UDF format
•
Multi-session discs (can only play the first session if the session's format is the supported format).
1.
Set the source selector to Disc.
– The POWER indicator lights up.
2.
Press OPEN to open the CD door.3.Insert a disc with the label side facing up.
4.
Close the CD door.
The total number of tracks and the playing time of the disc appear on the display.
For MP3-CD only
The total album number " " will be displayed
On TV screen, the total ALBUM and TRACK number will display, also with the album list (max.
5 lines per page) and an arrow. The arrow indicates the current selected music.
Notes : - To ensure good system performance, wait until the disc is completely reads before
proceeding.
- For MP3-CD, the disc reading time may exceed 10 seconds due to the large number of
songs compiled into one disc.
LOADING A DISC
DISCS FOR PLAYBACK
XXX
™
™
™
CD/VCD/MP3-CD
English
1.
Press
to start playback.
The track number and elapsed playing time of the current
track appear on the display.
•
To interrupt playback, press .
The playing time will start flashing.
•
To resume playback, press again.2.To stop playback, press .
To select a desired track
•
Press
or
on the set repeatedly (or on the remote control,
press
or
or digits 0 - 9, +10) until the desired track appears
on the display.
•
If playback is stopped, press to start playback.
To search for a particular passage during playback
•
Press and hold
or
on the set (or on the remote control,
press
or
) and release it when the desired passage is located.
During searching, the volume will be muted.
For MP3-CD only
To select a desired Album
•
Press and hold
or
on the set (or on the remote control, press
or
) until the desired album number appear on the display.
"" will be displayed and the album name will scroll
through the display briefly.
On TV screen, the arrow will move forward/backward in the
ALBUM menu.
To select a desired Track
•
Press
or
on the set repeatedly (or on the remote control, press
or
) to select a desired track from the current Album.
"" will be displayed and the track name will scroll
through the display briefly.
On TV screen, the arrow will move forward/backward in the
TRACK menu.
•
Use the digital keys on the remote control to select the track under
current Album directly.
To select and playback another track during playback mode
1.
Press
or
on the set (or on the remote control, press
or
) repeatedly to select another track.
The current track continues playing.
The new selected track will show on the display screen and
TV screen.
2.
Press to start playback the new selected track.
Note : - "" represents ALBUM is the current selected Album.
SELECTING A DESIRED TRACK/PASSAGE
PLAYING A NORMAL DISC
2;
2;
2;
2;
2;
9
§
§
§
§
§
§
§
∞
∞
∞
∞
∞
∞
∞
¡
¡
¡
™
™
™
XX
™
™
™
™
™
™
™
™
™
001
R
INSTRUCTIONS FOR USE
3 - 5
CD/VCD/MP3-CD
English
Programming tracks of disc is possible when playback is stopped. Up to 20 tracks can be stored in
the memory in any order (except for MP-3 CD).
1.
In stop mode, press PROGM to enter programme setting.
PROG will start flashing.
2.
Press digits 0 - 9, +10 on the remote control or
/
to select the desired track.
3.
Press PROGM to store the select track.
•
Repeat steps 1 to 3 to store other tracks.
4.
Press to end programme setting.
PROG will remain on the display.
•
Press
or
on the set (or on the remote control, press
or
) in stop mode to review the
programme sequence.
5.
Press to play the programmed tracks.
•
If you press REPEAT during programme playback, the current track or all programmed tracks will be
played repeatedly.
REPEAT/REPEAT ALL and PROG will appear on the display.
6.
Press in stop mode to clear the programme.
PROG will disappear from the display.
Notes : - "" represents PROGRAMME and " " represents TRACK, " " is the current selected
Programme or Track number.
- The programming is automatically cleared as soon as the CD compartment is opened.
- The function of programme setting is disable in PLAY/PAUSE mode.
- Programme cannot be used for VCDs when PBC is switched on. Switch off PBC before
storing tracks from such a VCD.
For MP3-CD only
1.
In stop mode, press
PROGM
.
PROG will start flashing and " " will be displayed.
On TV screen, "PXX AXX TXX?" and "PROGRAM" will be displayed.
2.
Press and hold
/
to select the desired ALBUM and press
/
repeatedly (or digits 0 -
9, +10 on the remote control) to select the desired TRACK for programming.
3.
Press
PROGM
to store the select track.
"" will show on the display screen and " " on TV screen.
PROG will remain on the display.
•
Repeat steps 1 to 3 to store other desired album and track.
•
Press or in stop mode can review the programme sequence.
"" will show on TV screen.
•
Press
/
in stop mode to show the programme information.
The Album's number and Track's number will show on the display screen.
4.
Press to start programme playback. You can press
/
to select the programmed track to
play.
5.
Press once stop programme playback or twice to clear the programme.
PROGRAMMING TRACKS
2;
2
9
9
9
§
§
§
§
§
§
§
∞
∞
∞
∞
∞
∞
∞
¡
™
XX
XX
OKXX
™
™
™
™
™
™
™
™
™
™
P
P
XX
P
XX
R
XXX
T
T
01
CD/VCD/MP3-CD
English
You can play all the tracks in random order.
1.
During playing, pause or stop mode, press SHUFFLE to enable SHUFFLE play mode.
SHUFFLE will appear on the display.
2.
To exit shuffle mode, press SHUFFLE again or .
SHUFFLE will disappear from the display.
Note : - If the Shuffle function enabled, and the Repeat function is set on, will disable the Shuffle
play mode.
You can play the current track or the whole disc repeatedly.
1.
During CD Playing or Pause mode, press REPEAT on the set or remote control.
REPEAT - to repeat the current track.
REPEAT ALL - to repeat the whole disc.
•
For MP3-CD, you are able to select REPEAT, REPEAT ALL or REPEAT ALB mode.
REPEAT ALB - to repeat the current album.
•
The current track or whole disc will now be played repeatedly until you press .2.To exit the repeat mode, press REPEAT until the REPEAT/REPEAT ALL/REPEAT ALB
disappears from the display.
Notes : - If the Repeat function is enable, and the Shuffle function is set on, will disable all the
Repeat play modes.
- If the Repeat function is enable, and the Stop button is pressed, will disable all the
Repeat play modes.
- In programme mode, you can only select Repeat or Repeat All function.
Adjusting the TV System
Before viewing the Video CD, ensure that the set is switched to corresponding PAL or NTSC system
of your TV set (exception Multi - system TV).
1.
Set the colour system selector to the PAL/A or NTSC/B
position as default setting. After TV system is selected, the set
will automatically switch to the default setting every time the
VCD source is selected.
2.
On the remote control, press NTSC/PAL to switch between NTSC
and PAL TV system.
OSD - On Screen Display
If you insert VCD/CD, your TV screen will serve as an additional display for messages (e.g. PLAY,
STOP), and information stored on the VCD/CD.
•
Press OSD on the remote control to select viewing various information.
The current track and current /remaining time in the track/disc appear on the display.
PAL / A
NTSC / B
...
...
OSC
1 2 3
VIDEO CD
REPEAT
SHUFFLE
9
9
™
™
™
™
™
™
INSTRUCTIONS FOR USE
3 - 6
CD/VCD/MP3-CD
English
Playing a Video CD with PBC
VCD with PBC (Playback Control) will be indicated on the display of the set and on your TV screen
as soon as they are inserted. PBC is a predefined play sequence stored on the VCD.
1.
Switch on the TV, insert a VCD with PBC.
2.
Menu appears on the TV screen.
If the menu consists of a list of titles, you can select a sequence directly
1.
Press digits 0 - 9, +10 on the remote control to select your choice.
The VCD starts playing of the selected sequence automatically.
2.
Press RETURN on the remote control to go back to the previous menu.
Note : - If a menu consists of more than one page, press
/
to go through the pages.
Switching off PBC
•
In stop mode, press PBC.
On TV screen, "PBC OFF" will be displayed.
Notes : - Programme mode is not available whenever PBC mode is switched on.
- The menu structure depends on the programme stored on the VCD. Please refer to the
information supplied with the disc.
Pause
1.
During playback, press to have a still picture on the TV screen.
The sound will be muted.
On TV screen, "PAUSE" will be displayed.
2.
Press again to continue playback.
Goto
1.
Press GOTO on the remote control.
":" will be displayed.
On TV screen, "GOTO --:--" will be displayed.
-- ---- --
2.
Press digits 0 - 9, +10 on the remote control to key in the disc time which you want the disc to
begin playback.
Note : - The disc time entered should not be greater than the total disc time.
Slow
1.
Press SLOW on the remote control to watch a VCD at a slower speed. There are 3 types of slow
modes to select.
The sound will be muted.
On TV screen, "SLOW 1/2", "SLOW 1/4" or "SLOW 1/8" will be displayed.
2.
To resume playback at normal speed, press SLOW repeatedly until "PLAY" appears on the TV
screen or press .
VIDEO CD
2
2
2
§∞
™
™
™
™
™
™
CD/VCD/MP3-CD
English
A-B repeat
This feature is also applicable to audio CD (except for MP3-CD). To Play a certain scene or passage
of the disc repeatedly.
1.
Press A-B on the remote control during playback to mark the start point of the chosen scene or
passage.
"A " will appear on the display.
2.
Press A-B again to mark the end of the chosen scene or passage.
"AB" will appear on the display.
The selected scene or passage will start playing repeatedly.
3.
Press A-B once more to return to normal playback.
"AB" will disappear from the display.
Notes : - You can also cancel A-B repeat by pressing
or .
- A-B repeat marking can cross from one track to another. But for VCD 2.0, you can only
able to set the A-B repeat marking within the same track.
Resume
•
In stop mode, press RESUME on the remote control to start playback again from where you have
stopped.
Note : - Resume will not be available if you have changed the disc, opened the disc tray or
disconnected the system the power supply.
View
This feature allows you to scan through a VCD for a quick review. PBC mode must be switched off.
1.
Press VIEW on the remote control.
On TV screen, 9 pictures will be displayed. To view the previous/next page, press or .
The first 20 seconds of each track will be played.
2.
To exit review mode, press digits 0 - 9, +10 to playback the desired track or to play the
current selected track.
Note : - If the disc is AVCD disc and there're no video tracks on the same viewed page, cannot use
the direct digital key to play the track.
Return
•
Press RETURN on the remote control to return to the previous VCD disc MENU level. It is
functional only for Video CD when PBC is switched on.
R/L
You can use it to select the different audio modes.
•
Press R/L on the remote control repeatedly to seleyct the following modes:
•
Channel Left/Right - Select the language on a bilingual VCD.
VIDEO CD
2
§
§
∞
∞
™™™™™
™
™
™
™
yy
INSTRUCTIONS FOR USE
Loading...