Copyright 2011 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
or otherwise without the prior permission of Philips.
Published by GD 1151 Service Audio Subject to modification
CLIMATIC REQUIREMENTS: (acc. to UAN-D1590)
All climates: -10 C till +50 C (Functional); Set has to be pre-conditioned for 2 hour, except CD function 8
For all measurements: 25 C9
POWER SUPPLY:
MAINS (AC) operationDC (int. or ext.) operation / Backup Buffer
Voltage
Battery type: 10
selection:
Selection:
See table below
Frequency:External DC: YES12
POWER CONSUMPTION:
Standby: Less than <0.5W
Maximum: 7 WMaximum: 14
General:
Q and R according to production division rules : Q < 1% (Major), Q < 4% (Minor)
Measured according to: R < 3% (CE52)
Power supply Tone Control AF-Amplifier Loudspeaker
Active
UTC8227 1
components
Passive
2 X 8, 2W
3
components
4
GENERAL part:
Aux in jack type Ø 3.5mm 5
Loudspeaker filter, high pass None 6
Loudspeaker filter, low pass None 7
Power stage protection Temperature – YES; Short circuit – YES 8
Public address No 9
INDICATORS:
Output power or VU-meter No 11
Frequency response No 12
Low power (battery) No
13
14
ELECTRICAL DATA:
TONE/EQUALIZER/DBB
DSC Balance control No 15
Mechanical noise (ISO 1996) 16
Noise overall (ISO) 17
Channel difference at -46dB Type: < 3 dB 18
Hum (vol.max.-20dB to vol.min.)Limit: 2mV 19
Residual noise(volume min)Limit: 2mV 20
DBB on (Vol.max.-20dB): 100Hz, +6dB
(2dB) w.r.t. 1kHz at DBB on
DBB off (Vol.max.-20dB): 100Hz, -2dB
(2dB) w.r.t. 1kHz at DBB on
DBB has no dynamic, fixed to
6dB
22
21
Input sens.:Nom. 500 mV 23
for 50mW Limit: 600 mV 24
Line outp.: Nom. mV 25
voltage Limit: mV 26
OUTPUT POWER:
Mains operation: D=10%
2 X 1W 8
Limit: -1dB 27
28
Music power (MPO) / (PMPO): (acc. to DIN45324) 29
Short term maximum output power: - (acc. to IEC 60268-15) 30
Long term maximum output power: - (acc. to IEC 60268-15) 31
Headphone output voltage/power: n.a. 32
Bandwidth FTC – 1dB at: n.a. (acc. to FTC/16/1/D/432) 33
Bandwidth DIN – 3dB at: - (acc. to IEC 60268-15) 34
Frequency response at Vol. max – 20dB:
typ. 60Hz to 20kHz (
3dB)
35
LOUDSPEAKER (output):
Low pass crossover frequency: - kHz tolerance: Hz36
High pass crossover frequency: - kHz tolerance: Hz37
Short term maximum output power: - W (acc. to IEC 60268-15) 38
Long term maximum output power: - W (acc. to IEC 60268-15) 39
Frequency response at: - Hz kHz 41
REMARKS:
42
27 : Measured in Tuner mode;
28: CD or Tape mode.
Recording level No 21
Play back level No 22
Tape counter No 23
Electrical data:
Bias system FM/AM 24
RIF switch No 25
Erase system FM/AM 26
Erasing damping 27
Channel separation (IEC1)28
Track separation (IEC1)29
Frequency response(PB)30
SNR 250nWb/m31
Signal/hiss 250nWb/m32
Signal/hum 250nWb/m33
Channel difference (PB)34
Distortion 250nWb/m 35
ALC attack time 36
ALC release time 37
Crosstalk Between forward to reverse track 38
REMARKS: 31: * not according to PQR clause 18.5 class I
31: ** Chromium performance not fulfilled
Amplification Reserve for Tape = 1dB 2dB
For details, please see specification SH-190 of ECO-MTF-PA-SD (3140 117 14890).
Fingerprint No audible defect TNO 11of Subchassis 8A 12
Black dot
500 m 600 m
Skew 0.6mm No audible defect TNO 1,6 of 0.6mm skew (7104 099
TNO 13 of SBC 444A (7104 099 24990) 13
14
28260)
Bad HF track No audible defect TNO 8 of Subchassis 8A 15
Heavy fingerprint No track
TNO 10 of Subchassis 8A 16
jumps/plops
Playback position Horizontal, Normal position (Set is located on a flat surface, floor) 17
- Playback of above mentioned tracks possible without track loss or audible defects. 18
- Double black dot, max. diameter, thin/thick disk is according to PQR or AR 30-05-239)
- This unit can playback (only) CD-R or CD-RW discs. For performance specification, please refer to
module
specification of CD99 (3103 308 52190)
Shock resistance: (acc. to AR 13-A6-CD-068)
Z axis
X or Y axis
4.5 G 19
4.5 G 20
Acoustical noise:
Mode: Play/Pause 35 dBA max. (45 dbA in Search mode) 21
Mode: Jump (Next) 45 dBA max. 22
AUDIO part: (Measured with Audio Signals Disc-1, 7104 078 04911 on Speakers or Headphone socket with nom.
load)
Typ. Limit 23
Output level (TNO1)24
SNR unwtd. 60 dB 48 dB 25
SNR wtd. dBA 65 dBA 57 dBA 26
Crosstalk (1kHz)40 dB 26 dB 27
Crosstalk (10kHz)30 dB 16 dB 28
Frequency response
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Tuner AM (MW,LW)
RF Generator
e.g. PM5326
Ri=50:
DUT
Frame aerial
e.g. 7122 707 89001
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
S/N and distortion meter
e.g. Sound Technology ST1700B
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
CD
Use Audio Signal Disc
(replaces test disc 3)
DUT
L
R
SBC429 4822 397 30184
S/N and distortion meter
e.g. Sound Technology ST1700B
LEVEL METER
e.g. Sennheiser UPM550
-
Recorder
Use Universal Test Cassette CrO2 SBC419 4822 397 30069
or Universal Test Cassette
LF Generator
e.g. PM5110
FeSBC420 4822 397 30071
DUT
L
R
S/N and distortion met
e.g. Sound Technology ST170
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
Page 12
SERVICE AIDS
1-4
GB
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
WARNING
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used
Safety components are marked by the symbol
!
.
ESD
CLASS 1
LASER PRODUCT
Lead free
Page 13
INSTRUCTIONS ON CD PLAYABILITY
Customer complaint
"CD related problem"
Set remains closed!
check playability
1
2 - 1
playability
ok ?
Y
Play a CD
for at least 10 minutes
check playability
playability
ok ?
Y
N
"fast" lens cleaning
check playability
playability
ok ?
N
3
N
Y
For flap loaders (= access to CD drive possible)
cleaning method
4 is recommended
add Info for customer
"SET OK"
2
return set
1 - 4 For description - see following pages
Exchange CDM
Page 14
INSTRUCTIONS ON CD PLAYABILITY
2 - 2
1
PLAYABILITY CHECK
For sets which are compatible with CD-RW discs
use CD-RW Printed Audio Disc....................7104 099 96611
TR 3 (Fingerprint)
TR 8 (600µ Black dot) maximum at 01:00
• playback of these two tracks without audible disturbance
playing time for: Fingerprint
Black dot from 00:50 to 01:10
• jump forward/backward (search) within a reasonable time
For all other sets
use CD-DA SBC 444A..................................4822 397 30245
TR 14 (600µ Black dot) maximum at 01:15
TR 19 (Fingerprint)
TR 10 (1000µ wedge)
• playback of all these tracks without audible disturbance
playing time for: 1000µ wedge 10seconds
Fingerprint 10seconds
Black dot from 01:05 to 01:25
• jump forward/backward (search) within a reasonable time
10seconds
4
LIQUID LENS CLEANING
Before touching the lens it is advised to clean the
surface of the lens by blowing clean air over it.
This to avoid that little particles make scratches on
the lens.
Because the material of the lens is synthetic and coated
with a special anti-reflectivity layer, cleaning must be done
with a non-aggressive cleaning fluid. It is advised to use
“Cleaning Solvent
The actuator is a very precise mechanical component and
may not be damaged in order to guarantee its full function.
Clean the lens gently (don’t press too hard) with a soft and
clean cotton bud moistened with the special lens cleaner.
The direction of cleaning must be in the way as indicated in
the picture below.
2
CUSTOMER INFORMATION
It is proposed to add an addendum sheet to the set which
informs the customer that the set has been checked
carefully - but no fault was found.
The problem was obviously caused by a scratched, dirty or
copy-protected CD. In case problems remain, the customer
is requested to contact the workshop directly.
The lens cleaning (method 3) should be mentioned in the
addendum sheet.
The final wording in national language as well as the printing
is under responsibility of the Regional Service Organizations.
Page 15
BLOCK DIAGRAM
3 - 13 - 1
Page 16
SET WIRING DIAGRAM
4 - 14 - 1
Page 17
5 - 15 - 1
CIRCUIT DIAGRAM-MAIN BOARD/TUNER BOARD/CONTROL BOARD
PART 1
Page 18
5 - 25 - 2
CIRCUIT DIAGRAM-MAIN BOARD/TUNER BOARD/CONTROL BOARD
PART 2
Page 19
5 -35 - 3
CIRCUIT DIAGRAM-MAIN BOARD/TUNER BOARD/CONTROL BOARD
PART 3
Page 20
5 - 45 - 4
Layout DIAGRAM-MAIN BOARD/TUNER BOARD/CONTROL BOARD
TOP SIDE VIEW
Page 21
5 - 55 - 5
Layout DIAGRAM-MAIN BOARD/TUNER BOARD/CONTROL BOARD
BOTTOM SIDE VIEW
Page 22
EXPLODED VIEW
6- 16 - 1
Page 23
Revision list
Version1.0 (3141 785 37120)
*Initial Release
7 - 1
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.