Philips AZ1330D User Manual

AUX

VOLUME

DBB

S O

DOCK

DOCK FOR

DOCKING ENTERTAINMENT SYSTEM AZ1330D

for

MP3-WMA PLAYBACK

0 9

3 4

5 6

6 x R20 • UM-1 • D-CELLS

& (

) ™

≤

8 6

∞

User manual

AZ1330DDocking Entertainment System

Hearing Safety

Listen at a moderate volume.

• Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss.

• Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So after prolonged listening, what sounds "normal" can actually be loud and harmful to your hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave it there.

To establish a safe volume level:

• Set your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.

Listen for reasonable periods of time:

• Prolonged exposure to sound, even at normally "safe" levels, can also cause hearing loss.

• Be sure to use your equipment reasonably and take appropriate breaks.

Be sure to observe the following guidelines when using your headphones.

• Listen at reasonable volumes for reasonable periods of time.

• Be careful not to adjust the volume as your hearing adapts.

• Do not turn up the volume so high that you can't hear what's around you.

•You should use caution or temporarily discontinue use in potentially hazardous situations.

• Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.; it may create a traffic hazard and is illegal in many areas.

English Controls / Power Supply

Supplied accessories

– AC power cord – Remote control – Docking kit

• 1 x Apple iPod dock (pre-installed with the main set)

• dock adaptors (8 adaptors for different iPod types)

• 1 dust cover (keep the dock connector from covering dust and dirt)

• Line-in cable

Top and front panels (See 1)

1 Telescopic antenna – improves FM

2 DOCK –

selects dock source

3 Dock connector – connects iPod

VOLUME/

MODE – selects different play modes:

VOL +/- –

e.g. REPEAT or SHUFFLE (random order)

6 PROGRAM

For disc

– programs tracks and reviews the

program

For Tuner

– auto searches and stores radio

stations

7 ALBUM/PRESET

For MP3-CD/ WMA play:

– select albums

For Tuner

– selects a preset radio station

8 / – opens/closes the disc tray

SOURCE:–selects CD/MP3-CD, DOCK

mode, Tuner or AUX

POWER –powers on/off the system

!2;–

starts or pauses disc/DOCK playback

∞§

For disc

/ DOCK play:

– skips to the beginning of a current/

reception

adjusts volume level

+/- (

3, 4

)

player

For Tuner:

– tunes to a radio station

9 –stops disc playback;

–

erases a program

DBB – turns on/off bass enhancement

@ p – 3.5 mm stereo headphone socket

Helpful hints: The speakers will be muted when headphones are connected to the set.

AUX jack –connects an external source

(3.5 mm socket)

$ Battery door – opens to inser t 6 x 1.5V

R-20/ -UM1/ D-cells

% Disc tray – load a disc

^ iR – infrared sensor for remote control

Remote control (See 1)

& CD – selects disc mode * TUNER – selects tuner mode ( DOCK – selects dock (iPod) source ) AUX– selects AUX mode

9 –stops disc playback;

–

erases a program

™ REPEAT – repeats a track/disc/all

programmed tracks

£ SHUFFLE – turns on/off the random play

mode

≤ DBB – turns on/off bass enhancement ∞ MUTE –mutes or restores the volume

Power Supply

Whenever convenient, use the power supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries.

Batteries Main set (See 1)

• Insert 6 batteries, type R-20, UM1 or D- cells (not included, preferably alkaline) with

the correct polarity.

previous/ later track

– fast searches backwards and forwards

within a track

English

Meet Philips at the Internet

http://www.philips.com

CLASS 1

LASER PRODUCT

AZ1330D

NOTES

Power Supply

Remote control

Important!

• Before using the remote control, remove the insulation plastic tab as shown in figure 9.

• If the remote control does not function correctly or the operating range is reduced, replace the battery with a new (CR2025) type battery.

1 Pull the battery tray out as shown

in figure 9.

2 Replace a new battery according to polarity

indication, and fully insert the batter y tray back to the original position.

• Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst:

• Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.

• When inserting new batteries, do not try to mix old batteries with the new ones.

• Remove the batteries if the set is not to be used for a long time.

Batteries contain chemical substances, so they should be disposed of properly.

Using AC power

1 Check if the power/mains voltage, as shown

on the type plate located on the bottom of the set, corresponds to your

local power supply. If it does not, consult your dealer or service center.

2 Connect the power cord to the

AC~ MAINS inlet and the wall socket.The

set is now ready for use.

3 To switch the set off completely, withdraw

the power cord from the wall socket.

4 Install the unit near the AC outlet and where

the AC power plug can be easily reached.

• Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms. Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit.

The type plate is located on the

bottom of the set.

Auto power saving

• In CD and DOCK mode, if AZ1330D is in

the PAUSE position for 5

minutes, it will auto

switch to the stop position.

• In CD and DOCK mode, if AZ1330D is in the STOP position for 15

minutes, it will auto

switch to standby to save power.

Helpful hints:

–To avoid unnecessary energy consumption,

always press POWER on the set to power off the set after using the set.

CAUTION

- Visible and invisible laser radiation.

If the cover is open, do not look at the beam.

- High voltage! Do not open.You run

the risk of getting an electric shock.The machine does not contain any user-serviceable parts.

- Modification of the product could

result in hazardous radiation of EMC or other unsafe operation.

Printed in China PDCC-JH-0721

Basic Function/Radio MP3-CD/CD Player

Basic functions

Switching on/off the set

1 To switch on, press POWER.

➜ Display lights up.The system will switch to

the last selected source.

2 To switch off, press POWER again.

➜ Display lights off.

Adjusting volume and sound

Adjust the sound with the VOLUME and DBB controls.

Digital tuner

Tuning to radio stations

1 Press repeatedly SOURCE (or TUNER

on the remote control) to select FM or MW.

➜ “TUNER” is displayed briefly, then the

radio station frequency, waveband and, if programmed, a preset number are shown (See 2).

2 Press and hold ∞ or § until the frequency in

the display starts running. ➜ The radio automatically tunes to a station

of sufficient reception. Display shows

SEARCH” during automatic tuning.

“

3 Repeat step 2 if necessary until you find the

desired station.

•To tune to a weak station, press ∞ or §

briefly and repeatedly until you have found optimal reception.

To improve radio reception:

• For FM, extend, incline and turn the

telescopic aerial. Reduce its length if the signal is too strong.

• For MW, the set uses a built-in aerial. Direct

this aerial by turning the whole set.

Programming radio stations

You can store 15 FM and 10 MW radio stations in the memory manually or automatically (Auto store).

Manual programming

1 Tune to your desired station (see Tuning to

radio stations).

2 Press PROG to activate programming.

➜ Display: PROG flashes.

3 Press ALBUM/PRESET +/-

(ALBUM/PRESET

3, 4

on the remote control ) once or more to allocate a number (from 1 to 25).

4 Press PROG to confirm.

5 Repeat steps 1-4 to store other stations.

Helpful hints:

–You can erase a preset station by storing

another frequency in its place.

Autostore

Autostore automatically starts programming radio stations from preset 1. Any previous presets e.g. manually programmed will be erased.

1 Press repeatedly SOURCE (or TUNER

on the remote control) to select FM or

MW.

2 Press PROG until “AUTO” flashes.

➜ Available stations are programmed (MW

or FM). After all stations are stored, the first autostore preset station will then automatically play.

To listen to a preset or autostore station

Press the ALBUM/PRESET +/-

3, 4

(ALBUM/PRESET

on the remote control ) buttons once or more until the desired preset station is displayed.

MP3-CD/CD Player

About MP3

The music compression technology MP3 (MPEG1 Audio Layer 3) significantly reduce the digital data of an audio CD while maintaining CD quality sound.

Getting MP3 files: you can either download

•

legal music files from the internet to your computer hard disc, or create such files by converting audio CD files in your computer through appropriate encoder software. (128kbps bit rate or higher is recommended for MP3 files.)

•

Creating a MP3 CD: burn the music files

from your computer hard disc on a CDR or CDRW using your CD burner.

Helpful hints:

– Make sure that the file names of the MP3 files

end with .mp3 or .wma. – Number of albums: maximum 100. – Number of tracks: maximum 999. – The length of file names affects the number of

tracks for playback.With shorter file names,

more files can be burned on a disc.

Playing a disc

This player plays Audio Discs including

CD-R/ CD-RW, MP3 CD and WMA. Do not

try to play a CD-ROM, CD-I, CDV,VCD,

DVD or computer CD.

IMPORTANT!

• CDs encoded with copyright protection

technologies by some record companies may

be unplayable by this product.

• DRM-protected WMA disc is not supported.

1 Press repeatedly SOURCE (CD on the

remote control) to select CD source.

➜ Display shows flashing “READ” if CD

source is selected (see 3).

➜ “ NO DISC” will be displayed if CD is not

loaded.

3 Press / to open the disc door.

4 Insert a disc with the printed side facing up

and press the disc door gently to close. ➜ The disc scanning of MP3-CD may run

longer than audio CD.

➜ Display: The total number of tracks

appears (and album number for MP3/WMA) (see 4).

5 Press

to start playback.

➜ First the song title of the track scrolls

across the display, then the track number and the elapsed playing time are displayed.

For MP3-CD/ WMA only:

➜ The current track number (TRK) and

album number (ALB) will be displayed interchangeably.

6 To pause playback press

➜ Display:2 and the elapsed playing time

flash.

7 Press

8 To stop playback, press

again to resume playback.

Helpful hints:

The disc playback will also stop when: –you open the disc compartment door ; –you select FM, MW, AUX or DOCK; – the disc has reached the end of the playback.

Selecting a different track

• Press ∞ or § once or repeatedly until the

desired track number appears in the display.

For MP3-CD/WMA: First press

ALBUM/PRESET +/- ( ALBUM/

PRESET

or more to find your album.

• In the pause/stop position, press 2; to start

playback.

3, 4

on the remote control ) once

MP3-CD/CD Player

Finding a passage within a track

1 During playback, press and hold down

∞ or §

➜ The disc is played at high speed and low

volume.

2 When you recognize the passage you want,

1 In the stop position, press

• For MP3-CD/WMA: First press

2 Press PROG to store desired track.

• If you attempt to program without first

3 Repeat steps 1 to 2 to select and store all

4 Press

– Display shows “NO PROG” if no track is

– If you try to store more than 20 tracks, no

∞ or §

release

➜ Normal playback resumes.

Programming tracks

You may store up to 20 tracks in the desired sequence. If you like, store any track more than once.

∞

your desired track number.

ALBUM/PRESET +/- ( ALBUM/PRESET

3, 4

on the remote control ) once or

more to find your album.

➜ Display shows “PRO 2” , indicating the

programmed location (See 5).

selectig a track, display will show “SELECT TRACK” briefly, then the total track number and playing time.

desired tracks.

to play the program.

➜ “PROG” is dispalyed during program

playback.

To review your program

In the stop position, press and hold PROG 3 seconds.

➜ The display shows all the stored tracks

(and album numbers for MP3) in sequence.

Helpful hints:

programmed.

track can be stored and the display will show ”PROGRAM FULL”.

or §to select

To erase a program

You can erase a program by:

– pressing

(twice during playback or once in

the stop position); – selecting FM, MW, AUX or DOCK; – pressing POWER to power off; – opening the disc door.

➜ “PROGRAM CLEAR” scrolls across the

display once, and “PROG” disappears.

Selecting different play

modes (See 6)

You can select and change the various play

modes before or during playback, and

combine play modes with PROG.

REP – plays the current track continuously.

REP ALL – plays the entire disc/program

continuously.

SHUF – plays all tracks in random order.

REP ALL SHUF – plays all tracks in

random order continuously.

1 To select play modes, press MODE on the

set (REPEAT or SHUFFLE on the remote

contorl) once or more.

2 Press 2; to start playback if in the stop

position.

➜ Shuffle play will start automatically soon

after shuffle mode is selected.

3 To select normal playback, press MODE on

the set (REPEAT or SHUFFLE on the

remote control) repeatedly until the various

play modes are no longer displayed.

– You can also press 9 to cancel your play

modes.

Helpful hints:

– Shuffle (SHUF and REP ALL SHUF) play is

not available in the program mode.

AUSTRALIA - Philips Manufacturers Warranty for Australia only

These warranty conditions are valid for the following consumer electronics products: Colour Televisions, Projection TV, Plasma & LCD TV, Video Cassette Recorders, CD Recorders & Players, DVD Players, DVD Recorders, DVD Recorders with HDD, Audio Systems, Home Theatre systems, Digital Set Top Box & Portable Audio products.

The benefits given to the purchaser by this warranty are in addition to all other rights and remedies which the purchaser has in respect of the product under the Trade Practices Act or other Commonwealth or State Law.

Philips Consumer Electronics warrants its products to the purchaser as follows and subject to the stated conditions.

1 Year Free Repair Service - at Philips ASC

Colour Television, Plasma Television, LCD Television, Projection Televsion, DVDR/VCR Combo, DVD Recorders with Hard Drive, LCD Projectors, Wireless Audio Systems, Audio Systems, Home Theatre Systems & Digital Set-Top-Box.

1 Year free Replacement – at your Retailer

Por table Audio, MP3 Infotainment products, Video Cassette recorders, DVD Player, DVD/VCR Combo Player, DVD Recorder without HDD & Portable DVD/LCD players.

Conditions of Repair Warranty

1. All claims for warranty service should be made to

your nearest Philips Authorised Service Centre or the Philips Technology Care Centre . Reasonable evidence of date of purchase must be provided.

2. This warranty extends only to defects in material or

workmanship occurring under normal use of the product when operated in accordance with the instructions.

3. If a replacement product is supplied under the repair

policy it is warranted, under this warranty, for the remainder of the warranty of the original purchased product only.

4. Home service is provided only within the normal

service area of one of our recommended Authorised Service Centres (ASC). It will be provided for television receivers only with a screen side of 67cms or above (product includes CRT, LCD TV, PTV, and Plasma TV). Televisions with screen side less than 67cms and all other products types are to be taken or sent by the consumer to the workshop of your nearest Authorised Service Centre, at the Consumer’s expense.

5. This Manufacturers Warranty is limited to 3 months

for the above listed Consumer Electronics products if used in commercial applications.

6. Philips may, at its discretion choose to replace rather

than repair any product covered by this warranty.

7. Product accessories are covered by the same

warranty period. Please contact the Philips Technology

Warranty valid for all new products purchased after 1

Care Centre for free replacement of faulty accessories.

8. This Manufacturers Warranty is neither transferable

nor valid in countries other than Australia.

This warranty does not cover:

a) Mileage or travel outside the normal ser vice area

covered by selected Authorised Service Centre.

b) Ser vice costs arising from failure to correctly adjust the controls of the product or to observe the instructions, or inspections that reveal that the product is in normal working order.

c) Product failures caused by misuse, neglect, accidental breakage, transit damage, inexpert repairs or modification by un-authorised persons, external fires, lightning strikes, floods, vermin infestation or liquid spillage.

d) Cleaning of video or audio heads.

e) Inadequate receiving antennae.

f) Replacement of worn or used batteries or other

consumables.

g) Consumer products used in commercial applications (This warranty is limited to 3 months only).

h) Second hand products.

The conditions contained in this warranty card replace and override the provision of the Philips World-Wide Guarantee for products purchased in Australia and used in Australia.

Service is provided through more than 100 accredited Authorised Service Centres throughout Australia. For direct contact with the nearest recommended Authorised Service Centre in capital & regional cities/towns

Authorised Service Centre Network

1300 361 392

Customer support is provided in Australia by our trained call centre staff. For assistance with product features and specifications, please call

Technology Care Centre

1300 363 391

Please record the following information for your records and keep in a safe place. We recommend retaining your purchase receipt to assist with any warranty claim.

Model number:....................................................

Serial number:....................................................

Date of purchase:....................................................

Retailer:....................................................

Philips Consumer Electronics

a division of Philips Electronics Australia Limited ABN 24 008 445 743, Level 1, 65 Epping Road NORTH RYDE NSW 2113.

January 2007

DOCK

Playing iPod using AZ1330D

By connecting the iPod to your AZ1330D, you can listen to the sound of the docked player through the powerful speakers of the Hi-Fi system.

Compatible portable player

Most Apple iPod models with 30-pin dock

• connector as follows:

20GB, 40GB, 20/30GB photo, 40/60GB photo, 30GB video, 60/80GB video, mini and nano.

Dock adaptor

Before plugging your player in the dock, snap the suitable dock adaptor into the dock to provide a snug fit for the player to be docked.

Selecting the correct dock adaptor

• For the iPod dock, 8 dock adaptors of different type, as indicated at the back of the adaptor, are included to fit the following iPod: 20GB, 40GB, 20/30GB photo, 40/60GB photo, 30GB video, 60GB video, miniand nano.

Playing Apple iPod using AZ1330D

1 Snap the compatible iPod into the dock

connector.

•

AZ1330D will auto switch to DOCK source (See 7).

2 For iPod, the connected player will play

automatically.

Auxiliary connection

Notes:

–

By using the buttons ( 2;, ¡1, 2™ and VOLUME ) on the AZ1330D and its remote control, the following disc playback features are available: Play/Pause, selecting next/previous track, fast forwarding/rewinding and changing volume.

–

The buttons ( 2;, ¡1, 2™ and VOLUME ) on the AZ1330D and its remote control can work only with playback of the audio contents stored on the docked player.

Charging iPod battery using the dock

In the power-on and standby mode of AZ1330D, you can charge the iPod when docking.

Helpful hints:

–

In DOCK and CD mode, if AZ1330D is in the STOP position for 15 minutes, it will auto switch to standby.

Connecting an external device

You can listen to the sound of the connected external device through your AZ1330D’s speakers.

1 Press repeatedly SOURCE (or AUX on the

remote contorl) to select AUX mode.

2 Use the supplied line-in cable to connect

AZ1330D’s AUX jack (3.5 mm, located on the top panel) to an AUDIO OUT or headphone jack on an external equipment (such as CD player, VCR or iPod).

Safety & Maintenance (See 8)

Safety information

• Place the set on a hard, flat and stable surface so that the system does not tilt.

• Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnet device shall remain readily operable.

• Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight.

• The apparatus shall not be exposed to dripping or splashing.

• Adequate ventilation with a minimum gap of 15 cm between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up.

• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.

• No objects filled with liquids, such as vases, shall be placed on the apparatus.

• No naked flame sources, such as lighted candles, should be placed on the apparatus.

• The mechanical par ts of the set contain self-lubricating bearings and must not be oiled or lubricated.

•To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing.

Environmental information

All unnecessary packaging material has been omitted.The packaging can be easily separated into three materials: cardboard, polystyrene and plastic.

Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment.

CD player and CD handling

• If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair.

• The lens of the CD player should never be touched!

• Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates.

•Always close the CD door to avoid dust on the lens.

•To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc.

• Never write on a CD or attach any stickers to it.

Troubleshooting

If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre.

WARNING: Do not open the set as there is a risk of electric shock. Under no cir-

cumstances should you try to repair the set yourself, as this will invalidate the guarantee.

No sound/ power

– Volume not adjusted

• Adjust the VOLUME – Power cord not securely connected

• Connect the AC power cord properly – Batteries dead/ incorrectly inserted

• Insert (fresh) batteries correctly – Disc contains non-audio files

• Insert a suitable disc or press

∞ or §

once or more skip to an audio track, instead of the data files.

Display does not function properly/No reaction to operation of any of the controls

– Electrostatic discharge

• Switch off and unplug the set. Reconnect after a few seconds.

no indication

– No disc inserted

• Insert a suitable disc

– Disc badly scratched or dirty

• Replace/clean CD (See Maintenance)

– CD-R(W) is blank or the disc is not finalized.

• Use a finalized CD-R(W)

– Laser lens steam up

•Wait until lens has cleared.

Note: Make sure the CD is not encoded with Copyright protection technologies, as some do not conform to the Compact Disc standard.

The disc skips tracks

– Disc damaged or dirty

• Replace or clean disc – Shuffle or program is active

• Switch off shuffle/program

Sound skips during MP3 playback

– MP3 file made at compression level exceeding

320kbps

• Use a lower compression level to record CD

tracks into MP3 format

– Disc damaged or dirty

• Replace or clean disc.

Note:

DRM-protected WMA disc is not supported.

Dock operation

–

The menu navigation or photo playback of the docked player cannot be carried out through the buttons on AZ1330D or its remote control.

• The buttons on AZ1330D and its remote control

can control playback of audio contents only.To navigate the menu, use the controls on the docked player.

–

Some buttons on AZ1330D and its remote control have no function.

• The buttons ( 2;, ¡1, 2™ and VOLUME )

function only.

NEW ZEALAND -

Thank-you for purchasing this quality Philips product.

Philips New Zealand Ltd guarantees this product against defective components and faulty workmanship for a period of 12 months. Any defect in materials or workmanship occurring within 12 months from the date of purchase subject to the following conditions will be rectified

free of charge by the retailer from whom this product was purchased.

Conditions

1. The product must have been purchased in New Zealand.As proof of purchase, retain the

original sales docket indicating the date of purchase.

2. The guarantee applies only to faults caused by defective components, or faulty workmanship

on the part of the manufacturer.

3. The guarantee does not cover failures caused by misuse, neglect, normal wear and tear,

accidental breakage, use onthe incorrect voltage, use contrary to operating instructions, or unauthorised modification to the product or repair by an unauthorised technician.

4. Reasonable evidence (in the form of a sales docket) must be supplied to indicate that the

product was purchased no more than 12 months prior to the date of your claim.

5. In the event of a failure, Philips shall be under no liability for any injury, or any loss or

damage caused to property or products other than the product under guarantee.

This guarantee does not prejudice your rights under common law and statute, and is in addition to the normal responsibilities of the retailer and Philips.

How to claim

Should your Philips product fail within the guarantee period, please return it to the retailer from whom it was purchased. In most cases the retailer will be able to satisfactorily repair or replace the product.

However, should the retailer not be able to conclude the matter satisfactorily, or if you have other difficulties claiming under this guarantee, please contact

The Guarantee Controller Philips New Zealand Ltd. 4 P.O. Box 41.021 Auckland 3 (09) 84 94 160

(09) 84 97 858

fax 3

Guarantee and Service for New Zealand