GB
TC
SC
(A)
b
(i) (ii)
a
d
c
(B)
/
/ /
e
30ml / 1oz
150ml / 5.5oz
150ml / 5.5oz
(iii)
(v)
(vii) (viii)
(iv)
(vi)
2 3
GB
310
285
255
230
200
170
11
10
9
8
7
6
Thank you for choosing Philips AVENT
The Philips AVENT Digital Bottle and Baby Food Warmer is the only warmer with advanced
Technology, designed to smartly and accurately adjust warming time based on contents and amount.
Whether warming milk or baby food that is frozen, chilled or at room temperature, the Digital Bottle
and Baby Food Warmer heats quickly, safely and evenly – with no hot spots. The versatile design holds
all AVENT Bottles, VIA Cups, and baby food jars or tins.
Please take 5 minutes to read through the ENTIRE INSTRUCTION LEAFLET including
the warnings before using your Digital Bottle and Baby Food Warmer for the rst time.
PLEASE RETAIN THESE INSTRUCTIONS for future reference. Instructions are also
available at www.philips.com/AVENT.
Contents (A):
a. Lid
b. Lid Flap – Lifts to accommodate
larger bottles (330ml/11oz)
c. Warmer Base
d. Lifter
e. Interactive Electronic Display
Interactive Electronic Display Guide
Milk Mode
(in ANY container)
Baby Food Mode
(in ANY container)
Freezer Temperature Mode
(Select when warming
from frozen)
Fridge Temperature Mode
(Select when warming
from chilled)
5
Room Temperature Mode
(Select when warming
from room temperature)
N.B. Whilst pressing the Power/Mode Selection or Volume Selection/Start Button, please hold the warmer base to prevent
the warmer from slipping.
140
115
4
ml
85
3
55
2
30
1
Power/Mode Selection Button –
Hold button for 3 seconds to switch
the warmer on/off. Press repeatedly
to select milk or baby food and
starting temperature.
Volume Selection/Start Button –
Press repeatedly to select the volume
of milk or food. Once desired
selections are made, hold button for
3 seconds to start warming cycle.
Volume Display –
Displays the selected amount of liquid
or food in both ml and oz
Instructions for Use
1. Ensure that the warmer is placed on a rm level surface. Open the lid using the front catch, and ll
the warmer with the appropriate amount of water (i) – See page 2 to determine water amount.
Place the fully assembled bottle (including dome cap to prevent overheating) or
with lid in the warmer. For food jars and tins, please refer to manufacturer’s instructions.
N.B. When warming a 330ml/11oz bottle, the lid ap will lift to accommodate the larger size.
This will cause a small amount of steam to rise from the warmer.
Close the lid ensuring that the front catch ‘clicks’ shut.
2. Plug in the warmer and switch on at the mains.
3. Switch on the warmer by holding the Power/Mode Selection Button for 3 seconds (ii). The
warmer will beep, and the milk, room temperature and ml/oz symbols will illuminate. It is now
ready for use. If the lid has not been closed correctly, the symbols will ash. When the unit is
switched on, it automatically defaults to the milk/room temperature mode. If this is the mode
you need, go to step 5. If not, proceed to step 4.
4. Choose milk or food, and select the starting temperature (iii) by pressing the Power/Mode
Selection Button repeatedly until the desired symbols are illuminated.
Please note that there are 6 possible options: milk from room temperature, milk from chilled,
storage container
milk from frozen, food from room temperature, food from chilled, and food from frozen. (See
Display Guide if needed.)
N.B. Warming food jars or tins from frozen is NOT recommended. However, you can warm
frozen food in VIA Cups within the warmer.
N.B. Please ensure that the correct options are selected, as milk and food should not be heated
for too long.
5. Select the amount of milk or food in the bottle or container by repeatedly pressing the Volume
Selection/Start Button until the desired volume is illuminated (iv). If the desired amount is not
shown on the display, please select the amount nearest to it.
N.B. For volumes in grams, select the same amount in ml (e.g. for 85g select 85ml).
N.B. The maximum volume that may be selected when warming food from frozen is 230ml/8oz.
6. Start the warming cycle (v): Once the desired settings are illuminated, hold down the Volume
Selection/Start Button until the warmer beeps. The volume display will now ash ascending and
descending lights up to the selected amount.
The warming cycle is in progress – Do not open the lid.
Completion of warming cycle (vi): When the cycle is complete, the warmer will beep intermittently
7.
for 30 seconds and all the volume display lights will continuously ash for 3 minutes. You can
remove the contents as soon as the warmer begins beeping. After 3 minutes, the warmer will
beep 5 times and will turn off automatically.
N.B. Philips AVENT recommends removing and using the contents immediately
when the
warming cycle is complete, even before the warmer automatically turns off.
8. Open the lid carefully to avoid any residual steam. Be careful when opening the lid as steam can
escape and cause injury. Use a cloth when removing the container, as it may be hot (vii). Use
the lifter to raise small bottles, VIA Cups, small food jars or tins. Pull the lifter just above the
circular rim. Rest the lifter on the rim where it naturally sits.
N.B. Do not remove the lifter from the warmer.
9. Before feeding your baby: Always check feed temperature before feeding
(a) Milk – shake the bottle or milk storage container and check the temperature of the milk
by sprinkling a few drops on the back of your hand.
(b) Food – stir the food thoroughly and test it yourself with a spoon to ensure it is not too hot.
If food is not warm enough, consult the Troubleshooting Guide.
N.B. Please ensure the lid of the container is tightly secured prior to shaking.
10. Unplug at the mains, and empty any residual water (viii). Ensure that the plug does not come
into contact with water. If warming an additional bottle or container, continue from step 1.
Otherwise, clean the inside and outside of the warmer with a damp cloth (viii). To remove the
lifter for cleaning purposes ONLY, lift vertically up until it naturally resists. Push the handle away
from you and rotate 90º or until it can naturally be removed, then lift out.
N.B. For microbiological and hygienic reasons, once heated, milk and food should not be
reheated again, and should be discarded if not used immediately. Please consult your health
professional/breastfeeding adviser for further guidance about safety recommendations on feeding.
N.B. If at any time the warmer is switched on and not running a cycle, it will automatically turn
off after 3 minutes if no selections have been made.
Approximate Warming Times
Milk 115ml/4oz from room temperature 2 mins
Milk 115ml/4oz from chilled 3 mins
Milk 255ml/9oz from room temperature 3 mins
Milk 255ml/9oz from chilled 4.5 mins
Food 230ml/8oz from room temperature 5 mins
Food 230ml/8oz from chilled 7 mins
4 5
Care of your Digital Bottle and Baby Food Warmer
Always unplug the warmer and allow it to cool before cleaning. Wipe the inside and outside of the
warmer with a damp cloth. DO NOT USE AN ABRASIVE CLEANER. Using cool pre-boiled or
ltered water in your warmer may reduce limescale build-up. When the warmer needs de-scaling,
the mode and starting temperature symbols will ash on the electronic display. To ensure maximum
effectiveness, you should de-scale your warmer every time it is required. To acknowledge the de-scale
warning, press and hold the Power/Mode Selection or Volume Selection/Start Button for 3 seconds.
If you do not wish to de-scale, please be aware that the unit will not remind you to de-scale on your
next use, but will instead begin re-counting cycles until the next de-scaling is needed.
IMPORTANT! DE-SCALING
Under no circumstances should anything other than citric acid or vinegar be used as it may cause
irreparable damage. Avoid contact with eyes as this may cause irritation. Keep out of the reach of children.
EITHER:
Mix one sachet of citric acid* (10g) with 200ml/7oz of water. Pour solution into the empty warmer.
DO NOT place a bottle, jar or cup into the warmer when de-scaling. Close the lid of the warmer
and programme the warmer to run with 310ml/11oz of milk from frozen. After the warming cycle
has ended, leave the solution to cool for 30 minutes before emptying the warmer and rinsing with tap
water. Wipe the inside and outside of the warmer with a damp cloth only.
OR:
Pour 100ml/3.5oz of vinegar mixed with 200ml/7oz of cold water into the warmer. Allow liquid to
stand in the unit until any limescale has dissolved. DO NOT place a bottle, jar or cup into the warmer
when de-scaling. DO NOT start the warming cycle. Empty the unit and rinse thoroughly. Wipe the
inside and outside of the warmer with a damp cloth only.
*Citric acid is available from most chemists and through Philips AVENT Customer Service.
WARNING!
The Digital Bottle and Baby Food Warmer is tted with a non-rewirable moulded plug. The mains supply lead of the appliance
CANNOT be replaced. If the lead is damaged, the appliance should be discarded. The supplied lead must not be used
on any other appliance and no other cord should be used with the Digital Bottle and Baby Food Warmer.
This product is manufactured to comply with the Radio Interference Requirements and the EEC Directive 89/336/EEC.
Failure to follow instructions may cause scalding or damage to product.
• Always ensure water has been added before switching on the warmer.
• Always ensure that you are using the correct volume of water before beginning the warming cycle. The warmer should be
emptied of residual water before each subsequent use.
• Heating food jars or tins from frozen within this warmer is NOT RECOMMENDED.
• To avoid possible scalding, do not place hands over the lid ap or open the lid ap during the warming cycle.
• When warming a 330ml/11oz bottle, the lid ap will lift to accommodate the larger size. This will cause a small amount of
steam to rise from the warmer.
• To avoid possible scalding, take care when opening the lid after a completed cycle as there may be some residual steam.
• When in use, the warmer contains hot water. Be careful to avoid spilling any water on yourself when removing
contents from the warmer.
• Use the lifter to remove small bottles, VIA Cups, and small baby food jars or tins.
• Always use a cloth when removing bottles, cups, jars and tins from the warmer.
• Always check feed temperature before feeding.
• For microbiological and hygienic reasons, once heated, milk and food should not be reheated again.
• Never immerse the warmer or power cord in water.
• This appliance is intended for use by responsible persons, keep out of the reach of small children and the inrm.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance.
• Failure to follow de-scaling instructions may cause irreparable damage.
• There are no serviceable parts inside the Digital Warmer. Do not attempt to open, service or repair the warmer yourself.
Troubleshooting Guide
The temperature of warmed food depends on the consistency of the food. Philips AVENT recommends
Food is not
warm enough
Milk is not
warm enough
Display will
not illuminate
/ Warmer will
not turn on
Symbols on
the display are
ashing
The warmer is
beeping
To stop the
warming cycle
To start the
warming cycle
If the lid is
opened during
warming cycle
Difculty
setting the
appropriate
amount of
frozen food
that, ideally, pureed food only should be heated with this warmer. If you nd that thicker food is not
warm enough at the end of the warming cycle, ll the warmer with an additional 30ml/1oz of water.
On step 4 and 5, choose the food from room temperature mode and programme the warmer at the
30ml/1oz option. Before feeding your baby, stir the food. Always check food temperature before feeding.
If you nd that milk is not warm enough at the end of a warming cycle, ll the warmer with an additional
30ml/1oz of water. On step 4 and 5, choose the milk from room temperature mode and programme the
warmer at the 30ml/1oz option. Before feeding your baby, shake the bottle or storage container gently
and check the temperature of the milk by sprinkling a few drops on the back of your hand.
Check that the lid is closed correctly. Check that the mains lead is plugged into the mains and the power
outlet is switched on. Then hold the Power/Mode Selection Button for 3 seconds.
• If the milk, room temperature and ml/oz symbols are ashing, then the lid has not been closed correctly.
• If all volume symbols are ashing, and the warmer beeps intermittently for 30 seconds then the cycle is
complete. Follow Step 8 onwards to remove the bottle or container from the warmer.
• If all mode and starting temperature symbols are ashing, then the unit requires de-scaling. See section
‘Care of your Digital Bottle and Baby Food Warmer’ on page 6. To acknowledge the de-scale warning,
press and hold the Power/Mode Selection or Volume Selection/Start Button for 3 seconds. If you do not
wish to de-scale, please be aware that this may cause irreparable damage.
• If ml/oz symbols ash, and the warmer beeps twice, insufcient water has been placed in the warmer.
Unplug the warmer, discard the milk or food and empty any remaining water. Be careful as the warmer is
hot. Follow instructions from Step 1 onwards.
• If all volume symbols are ashing, and the warmer beeps intermittently for 30 seconds then the cycle is
complete. Follow Step 8 onwards to remove the bottle or container from the warmer.
Press the Power/Mode Selection Button and the warmer will beep and return to default settings.
Once the correct mode, starting temperature and volume have been selected, press and hold the Volume
Selection/Start Button until the warmer beeps.
If the lid is opened at any time during the warming cycle, the lights on the display panel will ash and
the warmer will stop and return to default settings. In order to reset the warmer after the lid has been
opened, empty out any residual water, then follow instructions for use from step 1 onwards. Since this
could occur at any stage of the warming cycle, milk or food should be discarded for safety reasons.
The maximum volume that may be selected when warming food from frozen is 230ml/8oz.
Guarantee
Philips AVENT guarantees that should the Digital Bottle and Baby Food Warmer become faulty during 24
months from the date of purchase, it will be replaced free of charge during this time. Please return it to the
retailer where it was purchased. Please keep your receipt as proof of purchase, together with a note of when
and where purchased. For the guarantee to be valid, please note:
• The Digital Bottle and Baby Food Warmer must be used according to the instructions in this leaet and
connected to a suitable electricity supply.
• The claim must not be a result of accident, misuse, dirt, neglect or fair wear and tear.
This guarantee does not affect your statutory rights.
6 7
310
285
255
230
200
170
11
10
9
8
7
6
5
140
115
4
ml
85
3
55
2
30
1
8 9
10 11
310
285
255
230
200
170
11
10
9
8
7
6
5
140
115
4
ml
85
3
55
2
30
1
12 13
2009/08/20
14 15
Call FREE on 0800 289 064
GB
Call FREE on 1800 509 021
IRL
AU
1 300 364 474
TC
+886 (2) 8245 7399 / 0800-231-099
SC
400 880 0008
www.philips.com/AVENT
Philips AVENT, a business of Philips Electronics UK Ltd.
Philips Centre, Guildford Business Park, Guildford, Surrey, GU2 8XH
Trademarks owned by the Philips Group.
© Koninklijke Philips Electronics N.V. All Rights Reserved.
42133 5435 240 (08/09)
Loading...