Philips 89C51RB2, 89C51RC2, 89C51RD2 User Manual

http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
89C51RB2/89C51RC2/89C51RD2
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
Preliminary specification IC28 Data Handbook
 
1999 Sep 23
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
DESCRIPTION
The 89C51RB2/RC2/RD2 device contains a non-volatile 16kB/32kB/64kB Flash program memory that is both parallel programmable and serial In-System and In-Application Programmable. In-System Programming (ISP) allows the user to download new code while the microcontroller sits in the application. In-Application Programming (IAP) means that the microcontroller fetches new program code and reprograms itself while in the system. This allows for remote programming over a modem link. A default serial loader (boot loader) program in ROM allows serial In-System programming of the Flash memory via the UART without the need for a loader in the Flash code. For In-Application Programming, the user program erases and reprograms the Flash memory by use of standard routines contained in ROM.
This device executes one machine cycle in 6 clock cycles, hence providing twice the speed of a conventional 80C51. An OTP configuration bit lets the user select conventional 12 clock timing if desired.
This device is a Single-Chip 8-Bit Microcontroller manufactured in advanced CMOS process and is a derivative of the 80C51 microcontroller family . The instruction set is 100% compatible with the 80C51 instruction set.
The device also has four 8-bit I/O ports, three 16-bit timer/event counters, a multi-source, four-priority-level, nested interrupt structure, an enhanced UART and on-chip oscillator and timing circuits.
The added features of the P89C51RB2/RC2/RD2 makes it a powerful microcontroller for applications that require pulse width modulation, high-speed I/O and up/down counting capabilities such as motor control.
FEA TURES
80C51 Central Processing Unit
On-chip Flash Program Memory with In-System Programming
(ISP) and In-Application Programming (IAP) capability
Boot ROM contains low level Flash programming routines for
downloading via the UART
Can be programmed by the end-user application (IAP)
6 clocks per machine cycle operation (standard)
12 clocks per machine cycle operation (optional)
Speed up to 20 MHz with 6 clock cycles per machine cycle
(40 MHz equivalent performance); up to 33 MHz with 12 clocks per machine cycle
Fully static operation
RAM expandable externally to 64 kB
4 level priority interrupt
8 interrupt sources
Four 8-bit I/O ports
Full-duplex enhanced UART
Framing error detectionAutomatic address recognition
Power control modes
Clock can be stopped and resumedIdle modePower down mode
Programmable clock out
Second DPTR register
Asynchronous port reset
Low EMI (inhibit ALE)
Programmable Counter Array (PCA)
PWMCapture/compare
89C51RB2/89C51RC2/
89C51RD2
1999 Sep 23
2
Philips Semiconductors Preliminary specification
AMERICA)
VOLTAGE
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
89C51RB2/89C51RC2/
89C51RD2
ORDERING INFORMATION
PHILIPS
(EXCEPT NORTH
PART ORDER
NUMBER
PART MARKING
1 P89C51RB2HBP P89C51RB2BP 16 kB 512 B 0 to +70, PDIP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1 2 P89C51RB2HFP P89C51RB2FP 16 kB 512 B –40 to +85, PDIP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1 3 P89C51RB2HBA P89C51RB2BA 16 kB 512 B 0 to +70, PLCC 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2 4 P89C51RB2HFA P89C51RB2FA 16 kB 512 B –40 to +85, PLCC 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2 5 P89C51RB2HBB P89C51RB2BB 16 kB 512 B 0 to +70, PQFP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2 6 P89C51RB2HFB P89C51RB2FB 16 kB 512 B –40 to +85, PQFP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2 7 P89C51RC2HBP P89C51RC2BP 32 kB 512 B 0 to +70, PDIP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1 8 P89C51RC2HFP P89C51RC2FP 32 kB 512 B –40 to +85, PDIP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1
9 P89C51RC2HBA P89C51RC2BA 32 kB 512 B 0 to +70, PLCC 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2 10 P89C51RC2HFA P89C51RC2FA 32 kB 512 B –40 to +85, PLCC 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2 11 P89C51RC2HBB P89C51RC2BB 32 kB 512 B 0 to +70, PQFP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2 12 P89C51RC2HFB P89C51RC2FB 32 kB 512 B –40 to +85, PQFP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2 13 P89C51RD2HBP P89C51RD2BP 64 kB 1 kB 0 to +70, PDIP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1 14 P89C51RD2HFP P89C51RD2FP 64 kB 1 kB –40 to +85, PDIP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT129-1 15 P89C51RD2HBA P89C51RD2BA 64 kB 1 kB 0 to +70, PLCC 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2 16 P89C51RD2HFA P89C51RD2FA 64 kB 1 kB –40 to +85, PLCC 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT187-2 17 P89C51RD2HBB P89C51RD2BB 64 kB 1 kB 0 to +70, PQFP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2
18 P89C51RD2HFB P89C51RD2FB 64 kB 1 kB –40 to +85, PQFP 4.5–5.5 V 0 to 20 MHz 0 to 33 MHz SOT307-2
PHILIPS
NORTH
AMERICA
PART ORDER
NUMBER
MEMORY
FLASH RAM
TEMPERATURE
RANGE (°C)
AND PACKAGE
RANGE
FREQUENCY (MHz)
6 CLOCK
MODE
12 CLOCK
MODE
DWG #
1999 Sep 23
3
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
BLOCK DIAGRAM
P0.0–P0.7 P2.0–P2.7
PORT 0
DRIVERS
V
CC
V
SS
RAM ADDR REGISTER
B
REGISTER
RAM
ACC
TMP2
PORT 0
LATCH
TMP1
PORT 2
DRIVERS
PORT 2
LATCH
89C51RB2/89C51RC2/
89C51RD2
FLASH
8
STACK
POINTER
PROGRAM
ADDRESS
REGISTER
PSEN
EAV
ALE
PP
RST
TIMING
AND
CONTROL
OSCILLATOR
XTAL1 XTAL2
INSTRUCTION
PD
REGISTER
PSW
PORT 1
LATCH
PORT 1
DRIVERS
P1.0–P1.7
ALU
SFRs
TIMERS
P.C.A.
PORT 3
LATCH
PORT 3
DRIVERS
P3.0–P3.7
BUFFER
PC
INCRE-
MENTER
8 16
PROGRAM COUNTER
DPTR’S
MULTIPLE
SU01065
1999 Sep 23
4
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
LOGIC SYMBOL
RST
EA/V
PSEN
ALE/PROG RxD TxD
INT0 INT1
T0 T1
WR
RD
SECONDARY FUNCTIONS
PINNING
XTAL1
XTAL2
PP
PORT 3
V
V
SS
CC
ADDRESS AND
PORT 0
DATA BUS
T2 T2EX
PORT 1PORT 2
ADDRESS BUS
SU01302
Plastic Leaded Chip Carrier
89C51RB2/89C51RC2/
7
17
Pin Function
1 NIC* 2 P1.0/T2 3 P1.1/T2EX 4 P1.2/ECI 5 P1.3/CEX0 6 P1.4/CEX1 7 P1.5/CEX2 8 P1.6/CEX3
9 P1.7/CEX4 10 RST 11 P3.0/RxD 12 NIC* 13 P3.1/TxD 14 P3.2/INT0 15 P3.3/INT1
* NO INTERNAL CONNECTION
6140
LCC
18 28
Pin Function
16 P3.4/T0 17 P3.5/T1 18 P3.6/WR 19 P3.7/RD 20 XTAL2 21 XTAL1 22 V
SS
23 NIC* 24 P2.0/A8 25 P2.1/A9 26 P2.2/A10 27 P2.3/A11 28 P2.4/A12 29 P2.5/A13 30 P2.6/A14
89C51RD2
39
29
Pin Function
31 P2.7/A15 32 PSEN 33 ALE/PROG 34 NIC* 35 EA
/V 36 P0.7/AD7 37 P0.6/AD6 38 P0.5/AD5 39 P0.4/AD4 40 P0.3/AD3 41 P0.2/AD2 42 P0.1/AD1 43 P0.0/AD0 44 V
PP
CC
SU00023
Plastic Dual In-Line Package
T2/P1.0
1
T2EX/P1.1
CEX0/P1.3 CEX1/P1.4 CEX2/P1.5 CEX3/P1.6 CEX4/P1.7
INT0 INT1
ECI/P1.2
RST RxD/P3.0 TxD/P3.1
/P3.2
/P3.3 T0/P3.4 T1/P3.5
WR
/P3.6
RD
/P3.7
XTAL2 XTAL1
V
SS
2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20
DUAL
IN-LINE
PACKAGE
40
V P0.0/AD0
39 38
P0.1/AD1
37
P0.2/AD2
36
P0.3/AD3
35
P0.4/AD4
34
P0.5/AD5
33
P0.6/AD6
32
P0.7/AD7 EA/V
31 30
ALE/PROG
29
PSEN
28
P2.7/A15
27
P2.6/A14
26
P2.5/A13
25
P2.4/A12
24
P2.3/A11
23
P2.2/A10
22
P2.1/A9
21
P2.0/A8
CC
PP
SU00021
Plastic Quad Flat Pack
44 34
1
11
12 22
Pin Function
1 P1.5/CEX2 2 P1.6/CEX3 3 P1.7/CEX4 4 RST 5 P3.0/RxD 6 NIC* 7 P3.1/TxD 8 P3.2/INT0
9 P3.3/INT1 10 P3.4/T0 11 P3.5/T1 12 P3.6/WR 13 P3.7/RD 14 XTAL2 15 XTAL1
* NO INTERNAL CONNECTION
Pin Function
16 V 17 NIC* 18 P2.0/A8 19 P2.1/A9 20 P2.2/A10 21 P2.3/A11 22 P2.4/A12 23 P2.5/A13 24 P2.6/A14 25 P2.7/A15 26 PSEN 27 ALE/PROG 28 NIC* 29 EA 30 P0.7/AD7
PQFP
SS
/V
33
23
Pin Function
31 P0.6/AD6 32 P0.5/AD5 33 P0.4/AD4 34 P0.3/AD3 35 P0.2/AD2 36 P0.1/AD1 37 P0.0/AD0 38 V
CC
39 NIC* 40 P1.0/T2 41 P1.1/T2EX 42 P1.2/ECI 43 P1.3/CEX0
PP
44 P1.4/CEX1
SU00024
1999 Sep 23
5
Philips Semiconductors Preliminary specification
MNEMONIC
TYPE
NAME AND FUNCTION
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
89C51RB2/89C51RC2/
89C51RD2
PIN DESCRIPTIONS
PIN NUMBER
PDIP PLCC PQFP
V
SS
V
CC
P0.0–0.7 39–32 43–36 37–30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s
P1.0–P1.7 1–8 2–9 40–44,
P2.0–P2.7 21–28 24–31 18–25 I/O Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that
P3.0–P3.7 10–17 11,
RST 9 10 4 I Reset: A high on this pin for two machine cycles while the oscillator is running,
ALE 30 33 27 O Address Latch Enable: Output pulse for latching the low byte of the address
20 22 16 I Ground: 0 V reference. 40 44 38 I Power Supply: This is the power supply voltage for normal, idle, and power-down
1–3
1 2 40 I/O T2 (P1.0): Timer/Counter 2 external count input/Clockout (see Programmable
2 3 41 I T2EX (P1.1): Timer/Counter 2 Reload/Capture/Direction Control 3 4 42 I ECI (P1.2): External Clock Input to the PCA 4 5 43 I/O CEX0 (P1.3): Capture/Compare External I/O for PCA module 0 5 6 44 I/O CEX1 (P1.4): Capture/Compare External I/O for PCA module 1 6 7 1 I/O CEX2 (P1.5): Capture/Compare External I/O for PCA module 2 7 8 2 I/O CEX3 (P1.6): Capture/Compare External I/O for PCA module 3 8 9 3 I/O CEX4 (P1.7): Capture/Compare External I/O for PCA module 4
5, 7–13 I/O Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that
13–19
10 11 5 I RxD (P3.0): Serial input port
11 13 7 O TxD (P3.1): Serial output port 12 14 8 I INT0 (P3.2): External interrupt 13 15 9 I INT1 (P3.3): External interrupt 14 16 10 I T0 (P3.4): Timer 0 external input 15 17 11 I T1 (P3.5): Timer 1 external input 16 18 12 O WR (P3.6): External data memory write strobe 17 19 13 O RD (P3.7): External data memory read strobe
operation.
written to them float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s.
I/O Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups on all pins
except P1.6 and P1.7 which are open drain. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I
Alternate functions for 89C51RB2/RC2/RD2 Port 1 include:
Clock-Out)
have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to ext ernal data memory that use 8 -bit addres ses (MOV @Ri), port 2 emits the contents of the P2 special function register.
have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: I the special features of the 89C51RB2/RC2/RD2, as listed below:
resets the device. An internal diffused resistor to V using only an external capacitor to V
during an access to external memory. In normal operation, ALE is emitted twice every machine cycle, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. ALE can be disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during a MOVX instruction.
CC
).
IL
). Port 2
IL
). Port 3 also serves
IL
permits a power-on reset
.
SS
1999 Sep 23
6
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
MNEMONIC NAME AND FUNCTIONTYPE
MNEMONIC NAME AND FUNCTIONTYPE
PSEN 29 32 26 O Program Store Enable: The read strobe to external program memory. When
EA/V
PP
XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock
XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier.
NOTE:
To avoid “latch-up” effect at power-on, the voltage on any pin (other than V
PIN NUMBER
PQFPPLCCPDIP
executing code from the external program memory, PSEN machine cycle, except that two PSEN to external data memory. PSEN program memory.
31 35 29 I External Access Enable/Programming Supply Voltage: EA must be externally
held low to enable the device to fetch code from external program memory locations. If EA The value on the EA changes have no effect. This pin also receives the programming supply voltage
) during Flash programming.
(V
PP
generator circuits.
is held high, the device executes from internal program memory.
pin is latched when RST is released and any subsequent
) must not be higher than VCC + 0.5 V or less than VSS – 0.5 V.
PP
is not activated during fetches from internal
89C51RB2/89C51RC2/
89C51RD2
is activated twice each
activations are skipped during each access
1999 Sep 23
7
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
89C51RB2/89C51RC2/
89C51RD2
Table 1. Special Function Registers
SYMBOL DESCRIPTION
ACC* Accumulator E0H E7 E6 E5 E4 E3 E2 E1 E0 00H AUXR# Auxiliary 8EH – AUXR1# Auxiliary 1 A2H – B* B register F0H F7 F6 F5 F4 F3 F2 F1 F0 00H CCAP0H# Module 0 Capture High FAH xxxxxxxxB
CCAP1H# Module 1 Capture High FBH xxxxxxxxB CCAP2H# Module 2 Capture High FCH xxxxxxxxB CCAP3H# Module 3 Capture High FDH xxxxxxxxB CCAP4H# Module 4 Capture High FEH xxxxxxxxB CCAP0L# Module 0 Capture Low EAH xxxxxxxxB CCAP1L# Module 1 Capture Low EBH xxxxxxxxB CCAP2L# Module 2 Capture Low ECH xxxxxxxxB CCAP3L# Module 3 Capture Low EDH xxxxxxxxB CCAP4L# Module 4 Capture Low EEH xxxxxxxxB
CCAPM0# Module 0 Mode DAH ECOM CAPP CAPN MAT TOG PWM ECCF x0000000B CCAPM1# Module 1 Mode DBH ECOM CAPP CAPN MAT TOG PWM ECCF x0000000B CCAPM2# Module 2 Mode DCH ECOM CAPP CAPN MAT TOG PWM ECCF x0000000B CCAPM3# Module 3 Mode DDH ECOM CAPP CAPN MAT TOG PWM ECCF x0000000B CCAPM4# Module 4 Mode DEH ECOM CAPP CAPN MAT TOG PWM ECCF x0000000B
CCON*# PCA Counter Control D8H CF CR CCF4 CCF3 CCF2 CCF1 CCF0 00x00000B CH# PCA Counter High F9H 00H CL# PCA Counter Low E9H 00H
CMOD# PCA Counter Mode D9H CIDL WDTE CPS1 CPS0 ECF 00xxx000B DPTR: Data Pointer (2 bytes)
DPH Data Pointer High 83H 00H DPL Data Pointer Low 82H 00H
IE* Interrupt Enable 0 A8H EA EC ET2 ES ET1 EX1 ET0 EX0 00H
IP* Interrupt Priority B8H PPC PT2 PS PT1 PX1 PT0 PX0 x0000000B
IPH# Interrupt Priority High B7H PPCH PT2H PSH PT1H PX1H PT0H PX0H x0000000B
DIRECT
ADDRESS
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
MSB LSB
EXTRAM
ENBOOT
DF DE DD DC DB DA D9 D8
AF AE AD AC AB AA A9 A8
BF BE BD BC BB BA B9 B8
B7 B6 B5 B4 B3 B2 B1 B0
GF2 0 DPS xxxxxxx0B
AO xxxxxx10B
RESET VALUE
P0* Port 0 80H AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 FFH
P1* Port 1 90H CEX4 CEX3 CEX2 CEX1 CEX0 ECI T2EX T2 FFH
P2* Port 2 A0H AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 FFH
P3* Port 3 B0H RD WR T1 T0 INT1 INT0 TxD RxD FFH
PCON#1Power Control 87H SMOD1 SMOD0 GF1 GF0 PD IDL 00xxx000B
* SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs. – Reserved bits.
1. Reset value depends on reset source.
1999 Sep 23
87 86 85 84 83 82 81 80
97 96 95 94 93 92 91 90
A7 A6 A5 A4 A3 A2 A1 A0
B7 B6 B5 B4 B3 B2 B1 B0
8
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
89C51RB2/89C51RC2/
89C51RD2
Table 1. Special Function Registers (Continued)
SYMBOL DESCRIPTION
PSW* Program Status Word D0H CY AC F0 RS1 RS0 OV F1 P 00000000B
RCAP2H# Timer 2 Capture High CBH 00H RCAP2L# Timer 2 Capture Low CAH 00H
SADDR# Slave Address A9H 00H SADEN# Slave Address Mask B9H 00H
SBUF Serial Data Buffer 99H xxxxxxxxB
SCON* Serial Control 98H SP Stack Pointer 81H 07H
TCON* Timer Control 88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H
DIRECT
ADDRESS
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
MSB LSB
D7 D6 D5 D4 D3 D2 D1 D0
9F 9E 9D 9C 9B 9A 99 98
SM0/FE
8F 8E 8D 8C 8B 8A 89 88
SM1 SM2 REN TB8 RB8 TI RI 00H
RESET VALUE
CF CE CD CC CB CA C9 C8 T2CON* Timer 2 Control C8H TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 00H T2MOD# Timer 2 Mode Control C9H T2OE DCEN xxxxxx00B TH0 Timer High 0 8CH 00H
TH1 Timer High 1 8DH 00H TH2# Timer High 2 CDH 00H TL0 Timer Low 0 8AH 00H TL1 Timer Low 1 8BH 00H TL2# Timer Low 2 CCH 00H
TMOD Timer Mode 89H GATE C/T M1 M0 GATE C/T M1 M0 00H WDTRST Watchdog T imer Reset A6H
* SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs. – Reserved bits.
OSCILLA T OR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier. The pins can be configured for use as an on-chip oscillator.
To drive the device from an external clock source, XTAL1 should be driven while XTAL2 is left unconnected. Minimum and maximum high and low times specified in the data sheet must be observed.
This device is configured at the factory to operate using 6 clock periods per machine cycle, referred to in this datasheet as “6 clock mode”. (This yields performance equivalent to twice that of standard 80C51 family devices). It may be optionally configured on commercially-available EPROM programming equipment to operate at 12 clocks per machine cycle, referred to in this datasheet as “12 clock mode”. Once 12 clock mode has been configured, it cannot be changed back to 6 clock mode.
RESET
A reset is accomplished by holding the RST pin high for at least two machine cycles (12 oscillator periods in 6 clock mode, or 24 oscillator periods in 12 clock mode), while the oscillator is running. To ensure a good power-on reset, the RST pin mu st be h i gh l o n g enough to allow the oscillator time to start up (normally a few milliseconds) plus two machine cycles. At power-on, the voltage on V come up at the same time for a proper start-up. Ports 1, 2, and 3 will asynchronously be driven to their reset condition when a voltage above V
The value on the EA no further effect.
(min.) is applied to RESET.
IH1
pin is latched when RST is deasserted and has
and RST must
CC
1999 Sep 23
9
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
LOW POWER MODES Stop Clock Mode
The static design enables the clock speed to be reduced down to 0 MHz (stopped). When the oscillator is stopped, the RAM and Special Function Registers retain their values. This mode allows step-by-step utilization and permits reduced system power consumption by lowering the clock frequency down to any value. For lowest power consumption the Power Down mode is suggested.
Idle Mode
In the idle mode (see Table 2), the CPU puts itself to sleep while all of the on-chip peripherals stay active. The instruction to invoke the idle mode is the last instruction executed in the normal operating mode before the idle mode is activated. The CPU contents, the on-chip RAM, and all of the special function registers remain intact during this mode. The idle mode can be terminated either by any enabled interrupt (at which time the process is picked up at the interrupt service routine and continued), or by a hardware reset which starts the processor in the same manner as a power-on reset.
Power-Down Mode
To save even more power, a Power Down mode (see Table 2) can be invoked by software. In this mode, the oscillator is stopped and the instruction that invoked Power Down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values down to 2.0 V and care must be taken to return V the minimum specified operating voltages before the Power Down Mode is terminated.
Either a hardware reset or external interrupt can be used to exit from Power Down. Reset redefines all the SFRs but does not change the on-chip RAM. An external interrupt allows both the SFRs and the on-chip RAM to retain their values.
To properly terminate Power Down, the reset or external interrupt should not be executed before V operating level and must be held active long enough for the oscillator to restart and stabilize (normally less than 10 ms).
With an external interrupt, INT0 and INT1 must be enabled and configured as level-sensitive. Holding the pin low restarts the oscillator but bringing the pin back high completes the exit. Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put the device into Power Down.
is restored to its normal
CC
CC
to
POWER OFF FLAG
The Power Off Flag (POF) is set by on-chip circuitry when the V level on the 89C51RB2/RC2/RD2 rises from 0 to 5 V. The POF bit can be set or cleared by software allowing a user to determine if the reset is the result of a power-on or a warm start after powerdown. The V unaffected by the VCC level.
level must remain above 3 V for the POF to remain
CC
CC
Design Consideration
When the idle mode is terminated by a hardware reset, the device
ONCE Mode
The ONCE (“On-Circuit Emulation”) Mode facilitates testing and debugging of systems without the device having to be removed from the circuit. The ONCE Mode is invoked by:
1. Pull ALE low while the device is in reset and PSEN is high;
2. Hold ALE low as RST is deactivated. While the device is in ONCE Mode, the Port 0 pins go into a float
state, and the other port pins and ALE and PSEN high. The oscillator circuit remains active. While the device is in this mode, an emulator or test CPU can be used to drive the circuit. Normal operation is restored when a normal reset is applied.
Programmable Clock-Out
A 50% duty cycle clock can be programmed to come out on P1.0. This pin, besides being a regular I/O pin, has two alternate functions. It can be programmed:
1. to input the external clock for Timer/Counter 2, or
2. to output a 50% duty cycle clock ranging from 122 Hz to 8 MHz at
To configure the Timer/Counter 2 as a clock generator, bit C/T T2CON) must be cleared and bit T20E in T2MOD must be set. Bit TR2 (T2CON.2) also must be set to start the timer.
The Clock-Out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers (RCAP2H, RCAP2L) as shown in this equation:
Where (RCAP2H,RCAP2L) = the content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer.
In the Clock-Out mode Timer 2 roll-overs will not generate an interrupt. This is similar to when it is used as a baud-rate generator. It is possible to use Timer 2 as a baud-rate generator and a clock generator simultaneously. Note, however, that the baud-rate and the Clock-Out frequency will be the same.
89C51RB2/89C51RC2/
89C51RD2
normally resumes program execution, from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory.
are weakly pulled
a 16 MHz operating frequency (61 Hz to 4 MHz in 12 clock mode).
2 (in
Oscillator Frequency
n (65536 * RCAP2H,RCAP2L) n = 2 in 6 clock mode
4 in 12 clock mode
Table 2. External Pin Status During Idle and Power-Down Mode
MODE PROGRAM MEMORY ALE PSEN PORT 0 PORT 1 PORT 2 PORT 3
Idle Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power-down Internal 0 0 Data Data Data Data Power-down External 0 0 Float Data Data Data
1999 Sep 23
10
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
TIMER 2 OPERATION Timer 2
Timer 2 is a 16-bit Timer/Counter which can operate as either an event timer or an event counter, as selected by C/T function register T2CON (see Figure 1). Timer 2 has three operating modes: Capture, Auto-reload (up or down counting), and Baud Rate Generator, which are selected by bits in the T2CON as shown in Table 3.
2* in the special
Capture Mode
In the capture mode there are two options which are selected by bit EXEN2 in T2CON. If EXEN2=0, then timer 2 is a 16-bit timer or counter (as selected by C/T sets bit TF2, the timer 2 overflow bit. This bit can be used to generate an interrupt (by enabling the Timer 2 interrupt bit in the IE register). If EXEN2= 1, Timer 2 operates as described above, but with the added feature that a 1- to -0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. In addition, the transition at T2EX causes bit EXF2 in T2CON to be set, and EXF2 like TF2 can generate an interrupt (which vectors to the same location as Timer 2 overflow interrupt. The Timer 2 interrupt service routine can interrogate TF2 and EXF2 to determine which event caused the interrupt). The capture mode is illustrated in Figure 2 (There is no reload value for TL2 and TH2 in this mode. Even when a capture event occurs from T2EX, the counter keeps on counting T2EX pin transitions or osc/6 pulses (osc/12 in 12 clock mode).).
2* in T2CON) which, upon overflowing
Auto-Reload Mode (Up or Down Counter)
In the 16-bit auto-reload mode, Timer 2 can be configured (as either a timer or counter [C/T or down. The counting direction is determined by bit DCEN (Down
2* in T2CON]) then programmed to count up
Counter Enable) which is located in the T2MOD register (see Figure 3). When reset is applied the DCEN=0 which means Timer 2 will default to counting up. If DCEN bit is set, Timer 2 can count up or down depending on the value of the T2EX pin.
Figure 4 shows Timer 2 which will count up automatically since DCEN=0. In this mode there are two options selected by bit EXEN2 in T2CON register. If EXEN2=0, then T imer 2 counts up to 0FFFFH and sets the TF2 (Overflow Flag) bit upon overflow. This causes the Timer 2 registers to be reloaded with the 16-bit value in RCAP2L and RCAP2H. The values in RCAP2L and RCAP2H are preset by software means.
If EXEN2=1, then a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at input T2EX. This transition also sets the EXF2 bit. The Timer 2 interrupt, if enabled, can be generated when either TF2 or EXF2 are 1.
In Figure 5 DCEN=1 which enables Timer 2 to count up or down. This mode allows pin T2EX to control the direction of count. When a logic 1 is applied at pin T2EX Timer 2 will count up. Timer 2 will overflow at 0FFFFH and set the TF2 flag, which can then generate an interrupt, if the interrupt is enabled. This timer overflow also causes the 16-bit value in RCAP2L and RCAP2H to be reloaded into the timer registers TL2 and TH2.
When a logic 0 is applied at pin T2EX this causes Timer 2 to count down. The timer will underflow when TL2 and TH2 become equal to the value stored in RCAP2L and RCAP2H. Timer 2 underflow sets the TF2 flag and causes 0FFFFH to be reloaded into the timer registers TL2 and TH2.
The external flag EXF2 toggles when Timer 2 underflows or overflows. This EXF2 bit can be used as a 17th bit of resolution if needed. The EXF2 flag does not generate an interrupt in this mode of operation.
89C51RB2/89C51RC2/
89C51RD2
(MSB) (LSB)
TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2
Symbol Position Name and Significance
TF2 T2CON.7 Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set
EXF2 T2CON.6 Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and
RCLK T2CON.5 Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock
TCLK T2CON.4 Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock
EXEN2 T2CON.3 Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative
TR2 T2CON.2 Start/stop control for Timer 2. A logic 1 starts the timer. C/T2
CP/RL2
T2CON.1 Timer or counter select. (Timer 2)
T2CON.0 Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When
when either RCLK or TCLK = 1.
EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).
in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.
in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.
transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.
0 = Internal timer (OSC/6 in 6 clock mode or OSC/12 in 12 clock mode) 1 = External event counter (falling edge triggered).
cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow .
SU01251
Figure 1. Timer/Counter 2 (T2CON) Control Register
1999 Sep 23
11
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
89C51RB2/89C51RC2/
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
Table 3. Timer 2 Operating Modes
RCLK + TCLK CP/RL2 TR2 MODE
0 0 1 16-bit Auto-reload 0 1 1 16-bit Capture 1 X 1 Baud rate generator
X X 0 (off)
OSC
T2 Pin
÷ n*
Transition
Detector
C/T2
C/T2
= 0
= 1
TR2
Control
Capture
TL2
(8-bits)
RCAP2L RCAP2H
TH2
(8-bits)
TF2
89C51RD2
Timer 2
Interrupt
T2EX Pin
Control
EXEN2
EXF2
* n = 6 in 6 clock mode, or 12 in 12 clock mode.
Figure 2. Timer 2 in Capture Mode
T2MOD Address = 0C9H Reset Value = XXXX XX00B
Not Bit Addressable
T2OE DCEN
Bit
76543210
Symbol Function
Not implemented, reserved for future use.* T2OE Timer 2 Output Enable bit. DCEN Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down counter.
* User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features.
In that case, the reset or inactive value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
Figure 3. Timer 2 Mode (T2MOD) Control Register
SU01252
SU00729
1999 Sep 23
12
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
OSC
T2 PIN
T2EX PIN
* n = 6 in 6 clock mode, or 12 in 12 clock mode.
÷ n*
TRANSITION
DETECTOR
C/T2 = 0
C/T2
= 1
TL2
(8-BITS)
CONTROL
TR2
RELOAD
RCAP2L RCAP2H
CONTROL
EXEN2
Figure 4. Timer 2 in Auto-Reload Mode (DCEN = 0)
TH2
(8-BITS)
89C51RB2/89C51RC2/
89C51RD2
TF2
TIMER 2
INTERRUPT
EXF2
SU01253
T2 PIN
÷ n*
C/T2 = 0
C/T2
= 1
CONTROL
TR2
OSC
* n = 6 in 6 clock mode, or 12 in 12 clock mode.
Figure 5. Timer 2 Auto Reload Mode (DCEN = 1)
(DOWN COUNTING RELOAD VALUE)
FFH FFH
OVERFLOW
TL2 TH2
RCAP2L RCAP2H
(UP COUNTING RELOAD VALUE) T2EX PIN
TOGGLE
COUNT DIRECTION 1 = UP 0 = DOWN
TF2
EXF2
INTERRUPT
SU01254
1999 Sep 23
13
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
OSC
T2 Pin
T2EX Pin
Transition
Detector
C/T2 = 0
C/T2
= 1
TR2
Control
EXF2
TL2
(8-bits)
RCAP2L RCAP2H
Timer 2 Interrupt
TH2
(8-bits)
Reload
89C51RB2/89C51RC2/
89C51RD2
Timer 1
Overflow
÷ 2
“0” “1”
÷ 16
÷ 16
SMOD
RCLK
RX Clock
TCLK
TX Clock
“0”“1”
“0”“1”
Control
EXEN2
Note availability of additional external interrupt.
Figure 6. Timer 2 in Baud Rate Generator Mode
Table 4. Timer 2 Generated Commonly Used
Baud Rates
Baud Rate Timer 2
12 clock
mode
6 clock
mode
Osc Freq
RCAP2H RCAP2L
375 k 750 k 12 MHz FF FF
9.6 k 19.2 k 12 MHz FF D9
2.8 k 5.6 k 12 MHz FF B2
2.4 k 4.8 k 12 MHz FF 64
1.2 k 2.4 k 12 MHz FE C8 300 600 12 MHz FB 1E 110 220 12 MHz F2 AF 300 600 6 MHz FD 8F 110 220 6 MHz F9 57
Baud Rate Generator Mode
Bits TCLK and/or RCLK in T2CON (Table 4) allow the serial port transmit and receive baud rates to be derived from either Timer 1 or Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit baud rate generator . When TCLK= 1, Timer 2 is used as the serial port transmit baud rate generator. RCLK has the same effect for the serial port receive baud rate. With these two bits, the serial port can have different receive and transmit baud rates – one generated by Timer 1, the other by Timer 2.
Figure 6 shows the Timer 2 in baud rate generation mode. The baud rate generation mode is like the auto-reload mode,in that a rollover in TH2 causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and RCAP2L, which are preset by software.
SU01213
The baud rates in modes 1 and 3 are determined by Timer 2’s overflow rate given below:
Modes 1 and 3 Baud Rates +
Timer 2 Overflow Rate
16
The timer can be configured for either “timer” or “counter” operation. In many applications, it is configured for “timer” operation (C/T
2*=0). Timer operation is different for Timer 2 when it is being used as a baud rate generator.
Usually, as a timer it would increment every machine cycle (i.e.,
1
/6 the oscillator frequency in 6 clock mode, 1/12 the oscillator frequency in 12 clock mode). As a baud rate generator, it increments at the oscillator frequency in 6 clock mode (
OSC
/2 in 12 clock mode).
Thus the baud rate formula is as follows:
Modes 1 and 3 Baud Rates =
Oscillator Frequency
[n* [65536 * (RCAP2H,RCAP2L)]]
* n = 16 in 6 clock mode
32 in 12 clock mode
Where: (RCAP2H, RCAP2L)= The content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer.
The Timer 2 as a baud rate generator mode shown in Figure 6, is valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a rollover in TH2 does not set TF2, and will not generate an interrupt. Thus, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the baud rate generator mode. Also if the EXEN2 (T2 external enable flag) is set, a 1-to-0 transition in T2EX (Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2). Therefore when Timer 2 is in use as a baud rate generator, T2EX can be used as an additional external interrupt, if needed.
1999 Sep 23
14
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
89C51RB2/89C51RC2/
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
When Timer 2 is in the baud rate generator mode, one should not try to read or write TH2 and TL2. As a baud rate generator, T imer 2 is incremented every state time (osc/2) or asynchronously from pin T2; under these conditions, a read or write of TH2 or TL2 may not be accurate. The RCAP2 registers may be read, but should not be written to, because a write might overlap a reload and cause write and/or reload errors. The timer should be turned off (clear TR2) before accessing the Timer 2 or RCAP2 registers.
Table 4 shows commonly used baud rates and how they can be obtained from Timer 2.
Summary of Baud Rate Equations
Timer 2 is in baud rate generating mode. If Timer 2 is being clocked through pin T2(P1.0) the baud rate is:
Baud Rate +
Timer 2 Overflow Rate
16
Table 5. Timer 2 as a Timer
MODE
16-bit Auto-Reload 00H 08H 16-bit Capture 01H 09H Baud rate generator receive and transmit same baud rate 34H 36H Receive only 24H 26H Transmit only 14H 16H
If Timer 2 is being clocked internally, the baud rate is:
f
Baud Rate +
Where f
OSC
To obtain the reload value for RCAP2H and RCAP2L, the above equation can be rewritten as:
RCAP2H,RCAP2L + 65536 *
[n* [65536 * (RCAP2H,RCAP2L)]]
* n = 16 in 6 clock mode
= Oscillator Frequency
OSC
32 in 12 clock mode
f
ǒ
n* Baud Rate
Timer/Counter 2 Set-up
Except for the baud rate generator mode, the values given for T2CON do not include the setting of the TR2 bit. Therefore, bit TR2 must be set, separately, to turn the timer on. see Table 5 for set-up of Timer 2 as a timer. Also see Table 6 for set-up of Timer 2 as a counter.
T2CON
INTERNAL CONTROL
(Note 1)
EXTERNAL CONTROL
89C51RD2
OSC
(Note 2)
Ǔ
Table 6. Timer 2 as a Counter
TMOD
MODE
16-bit 02H 0AH Auto-Reload 03H 0BH
NOTES:
1. Capture/reload occurs only on timer/counter overflow.
2. Capture/reload occurs on timer/counter overflow and a 1-to-0 transition on T2EX (P1.1) pin except when Timer 2 is used in the baud rate generator mode.
INTERNAL CONTROL
(Note 1)
EXTERNAL CONTROL
(Note 2)
1999 Sep 23
15
Philips Semiconductors Preliminary specification
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
Enhanced UART
The UART operates in all of the usual modes that are described in the first section of
Microcontrollers
detect by looking for missing stop bits, and automatic address recognition. The UART also fully supports multiprocessor communication as does the standard 80C51 UART.
When used for framing error detect the UART looks for missing stop bits in the communication. A missing bit will set the FE bit in the SCON register. The FE bit shares the SCON.7 bit with SM0 and the function of SCON.7 is determined by PCON.6 (SMOD0) (see Figure 7). If SMOD0 is set then SCON.7 functions as FE. SCON.7 functions as SM0 when SMOD0 is cleared. When used as FE SCON.7 can only be cleared by software. Refer to Figure 8.
Automatic Address Recognition
Automatic Address Recognition is a feature which allows the UART to recognize certain addresses in the serial bit stream by using hardware to make the comparisons. This feature saves a great deal of software overhead by eliminating the need for the software to examine every serial address which passes by the serial port. This feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will be automatically set when the received byte contains either the “Given” address or the “Broadcast” address. The 9-bit mode requires that the 9th information bit is a 1 to indicate that the received information is an address and not data. Automatic address recognition is shown in Figure 9.
The 8 bit mode is called Mode 1. In this mode the RI flag will be set if SM2 is enabled and the information received has a valid stop bit following the 8 address bits and the information is either a Given or Broadcast address.
Mode 0 is the Shift Register mode and SM2 is ignored. Using the Automatic Address Recognition feature allows a master to
selectively communicate with one or more slaves by invoking the Given slave address or addresses. All of the slaves may be contacted by using the Broadcast address. Two special Function Registers are used to define the slave’s address, SADDR, and the address mask, SADEN. SADEN is used to define which bits in the SADDR are to b used and which bits are “don’t care”. The SADEN mask can be logically ANDed with the SADDR to create the “Given” address which the master will use for addressing each of the slaves. Use of the Given address allows multiple slaves to be recognized while excluding others. The following examples will help to show the versatility of this scheme:
Slave 0 SADDR = 1100 0000
Data Handbook IC20, 80C51-Based 8-Bit
. In addition the UART can perform framing error
SADEN = 1111 1101 Given = 1100 00X0
Slave 1 SADDR = 1100 0000
In the above example SADDR is the same and the SADEN data is used to differentiate between the two slaves. Slave 0 requires a 0 in bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is ignored. A unique address for Slave 0 would be 1100 0010 since slave 1 requires a 0 in bit 1. A unique address for slave 1 would be 1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0 (for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000.
In a more complex system the following could be used to select slaves 1 and 2 while excluding slave 0:
Slave 0 SADDR = 1100 0000
Slave 1 SADDR = 1110 0000
Slave 2 SADDR = 1110 0000
In the above example the differentiation among the 3 slaves is in the lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 01 10. Slave 1 requires that bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2 use address 1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2.
The Broadcast Address for each slave is created by taking the logical OR of SADDR and SADEN. Zeros in this result are trended as don’t-cares. In most cases, interpreting the don’t-cares as ones, the broadcast address will be FF hexadecimal.
Upon reset SADDR (SFR address 0A9H) and SADEN (SFR address 0B9H) are leaded with 0s. This produces a given address of all “don’t cares” as well as a Broadcast address of all “don’t cares”. This effectively disables the Automatic Addressing mode and allows the microcontroller to use standard 80C51 type UART drivers which do not make use of this feature.
89C51RB2/89C51RC2/
89C51RD2
SADEN = 1111 1110 Given = 1100 000X
SADEN = 1111 1001 Given = 1100 0XX0
SADEN = 1111 1010 Given = 1110 0X0X
SADEN = 1111 1100 Given = 1110 00XX
1999 Sep 23
16
Loading...
+ 36 hidden pages