Philips 74HCT4351U, 74HCT4351N, 74HCT4351DB, 74HCT4351D, 74HC4351N Datasheet
...
DATA SH EET
Product specification
File under Integrated Circuits, IC06
December 1990
INTEGRATED CIRCUITS
74HC/HCT4351
8-channel analog
multiplexer/demultiplexer with latch
For a complete data sheet, please also download:
•The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
•The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
•The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines
December 1990 2
Philips Semiconductors Product specification
8-channel analog
multiplexer/demultiplexer with latch
74HC/HCT4351
FEATURES
• Wide analog input voltage range:
± 5 V
• Low “ON” resistance:
80 Ω (typ.) at VCC− VEE= 4.5 V
70 Ω (typ.) at VCC− VEE= 6.0 V
60 Ω (typ.) at VCC− VEE= 9.0 V
• Logic level translation: to enable 5 V logic to
communicate with ± 5 V analog signals
• Typical “break before make” built in
• Address latches provided
• Output capability: non-standard
• ICC category: MSI
GENERAL DESCRIPTION
The 74HC/HCT4351 are high-speed Si-gate CMOS
devices. They are specified in compliance with JEDEC
standard no. 7A.
The 74HC/HCT4351 are 8-channel analog
multiplexers/demultiplexers with three select inputs (S
0
to
S2), two enable inputs (E1and E2), a latch enable input
(LE), eight independent inputs/outputs (Y0to Y7) and a
common input/output (Z).
With E1LOW and E2is HIGH, one of the eight switches is
selected (low impedance ON-state) by S0to S2. The data
at the select inputs may be latched by using the active
LOW latch enable input (LE). When LE is HIGH the latch
is transparent. When either of the two enable inputs,
E1(active LOW) and E2(active HIGH), is inactive, all 8
analog switches are turned off.
VCCand GND are the supply voltage pins for the digital
control inputs (S0to S2, LE, E1and E2). The VCCto GND
ranges are 2.0 to 10.0 V for HC and 4.5 to 5.5 V for HCT.
The analog inputs/outputs (Y0to Y7, and Z) can swing
between VCCas a positive limit and VEEas a negative
limit.
VCC− VEEmay not exceed 10.0 V.
For operation as a digital multiplexer/demultiplexer, VEEis
connected to GND (typically ground).
QUICK REFERENCE DATA
VEE= GND = 0 V; T
amb
=25°C; tr=tf= 6 ns
SYMBOL PARAMETER CONDITIONS
TYPICAL
UNIT
HC HCT
t
PZH
/ t
PZL
turn “ON” time E1, E2or Snto V
os
CL= 15 pF; RL=1 kΩ; VCC=5 V2735ns
t
PHZ
/ t
PLZ
turn “OFF” time E1, E2or Snto V
os
21 23 ns
C
I
input capacitance 3.5 3.5 pF
C
PD
power dissipation capacitance per switch notes 1 and 2 25 25 pF
C
S
max. switch capacitance
independent (Y) 5 5 pF
common (Z) 25 25 pF
Notes
1. CPD is used to determine the dynamic power
dissipation (PD in µW):
PD=CPD× V
CC
2
× fi+∑ {(CL+ C
S
)
× V
CC
2
× fo}
where:
fi= input frequency in MHz
fo= output frequency in MHz
CL= output load capacitance in pF
CS= max. switch capacitance in pF
∑ {(CL+ C
S
)
× V
CC
2
× fo} = sum of outputs
VCC= supply voltage in V
2. For HC the condition is VI= GND to V
CC
For HCT the condition is VI= GND to VCC− 1.5 V
ORDERING INFORMATION
See
“74HC/HCT/HCU/HCMOS Logic Package
Information”
.
December 1990 3
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer
with latch
74HC/HCT4351
PIN DESCRIPTION
PIN NO. SYMBOL NAME AND FUNCTION
4 Z common
3, 14 n.c. not connected
7
E
1
enable input (active LOW)
8E
2
enable input (active HIGH)
9V
EE
negative supply voltage
10 GND ground (0 V)
11
LE latch enable input (active LOW)
15, 13, 12 S
0
to S
2
select inputs
17, 18, 19, 16, 1, 6, 2, 5 Y
0
to Y
7
independent inputs/outputs
20 V
CC
positive supply voltage
Fig.1 Pin configuration. Fig.2 Fig.3 IEC logic symbol.
December 1990 4
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer
with latch
74HC/HCT4351
FUNCTION TABLE
Notes
1. Last selected channel “ON”.
2. Selected channels latched.
3. H = HIGH voltage level
L = LOW voltage level
X = don’t care
↓ = HIGH-to-LOW LE transition
APPLICATIONS
• Analog multiplexing and demultiplexing
• Digital multiplexing and demultiplexing
• Signal gating
INPUTS
CHANNEL
ON
E
1
E
2
LE S
2
S
1
S
0
H
X
X
L
X
X
X
X
X
X
X
X
none
none
L
L
L
L
H
H
H
H
H
H
H
H
L
L
L
L
L
L
H
H
L
H
L
H
Y
0
Y
1
Y
2
Y
3
L
L
L
L
H
H
H
H
H
H
H
H
H
H
H
H
L
L
H
H
L
H
L
H
Y
4
Y
5
Y
6
Y
7
L
X
H
X
L
↓
X
X
X
X
X
X
(1)
(2)
Fig.4 Functional diagram.
Fig.5 Schematic diagram (one switch).
December 1990 5
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer
with latch
74HC/HCT4351
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Voltages are referenced to VEE= GND (ground = 0 V)
Note to ratings
1. To avoid drawing V
CC
current out of terminal Z, when switch current flows in terminals Yn, the voltage drop across
the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCCcurrent will flow out
of terminals Yn. In this case there is no limit for the voltage drop across the switch, but the voltages at Yn and Z may
not exceed VCCor VEE.
RECOMMENDED OPERATING CONDITIONS
SYMBOL PARAMETER MIN. MAX. UNIT CONDITIONS
V
CC
DC supply voltage −0.5 +11.0 V
±I
IK
DC digital input diode current 20 mA for VI<−0.5 V or VI> VCC+ 0.5 V
±I
SK
DC switch diode current 20 mA for VS<−0.5 V or VS> VCC+ 0.5 V
±I
S
DC switch current 25 mA for −0.5 V < VS< VCC+ 0.5 V
±I
EE
DC VEE current 20 mA
±I
CC;±IGND
DC VCCor GND current 50 mA
T
stg
storage temperature range −65 +150 °C
P
tot
power dissipation per package for temperature range: −40 to +125 °C
74HC/HCT
plastic DIL 750 mW above +70 °C: derate linearly with 12 mW/K
plastic mini-pack (SO) 500 mW above +70 °C: derate linearly with 8 mW/K
P
S
power dissipation per switch 100 mW
SYMBOL PARAMETER
74HC 74HCT
UNIT CONDITIONS
min. typ. max. min. typ. max.
V
CC
DC supply voltage VCC−GND 2.0 5.0 10.0 4.5 5.0 5.5 V see Figs 6 and 7
V
CC
DC supply voltage VCC−V
EE
2.0 5.0 10.0 2.0 5.0 10.0 V see Figs 6 and 7
V
I
DC input voltage range GND V
CC
GND V
CC
V
V
S
DC switch voltage range V
EE
V
CCVEE
V
CC
V
T
amb
operating ambient temperature range −40 +85 −40 +85 °C see DC and AC
CHARACTERISTICS
T
amb
operating ambient temperature range −40 +125 −40 +125 °C
t
r
, t
f
input rise and fall times
6.0
1000
500
400
250
6.0 500 ns
VCC= 2.0 V
VCC= 4.5 V
VCC= 6.0 V
VCC= 10.0 V
December 1990 6
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer
with latch
74HC/HCT4351
Fig.6 Guaranteed operating area as a function
of the supply voltages for 74HC4351.
handbook, halfpage
10
8
6
4
2
0
0246810
VCC- VEE(V)
VCC- GND
(V)
MBA334
operating area
Fig.7 Guaranteed operating area as a function of
the supply voltages for 74HCT4351.
DC CHARACTERISTICS FOR 74HC/HCT
For 74HC: V
CC
− GND or VCC− VEE= 2.0, 4.5, 6.0 and 9.0 V
For 74HCT: V
CC
− GND = 4.5 and 5.5 V; VCC− VEE= 2.0, 4.5, 6.0 and 9.0 V
Notes to DC characteristics
1. At supply voltages (V
CC
− VEE) approaching 2.0 V, the analog switch ON-resistance becomes extremely non-linear.
There it is recommended that these devices be used to transmit digital signals only, when using these supply
voltages.
2. For test circuit measuring RONsee Fig.8.
SYMBOL PARAMETER
T
amb
(°C)
UNIT
TEST CONDITIONS
74HC/HCT
V
CC
(V)
V
EE
(V)
I
S
(µA)
V
is
V
I
+25 −40 to +85
−40 to
+125
min. typ. max. min. max. min. max.
R
ON
ON resistance
(rail)
−
100
90
70
−
180
160
130
−
225
200
165
−
270
240
195
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
100
1000
1000
1000
V
CC
to
V
EE
V
IN
or
V
IL
R
ON
ON resistance
(rail)
150
80
70
60
−
140
120
105
−
175
150
130
−
210
180
160
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
100
1000
1000
1000
V
EEVIH
or
V
IL
R
ON
ON resistance
(rail)
150
90
80
65
−
160
140
120
−
200
175
150
−
240
210
180
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
100
1000
1000
1000
V
CCVIH
or
V
IL
∆R
ON
maximum ∆ ON
resistance
between any two
channels
−
9
8
6
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
V
CC
to
V
EE
V
IH
or
V
IL
Loading...