Philips 26MF605W Schematic

FL-1 Wide LCD Monitor / TV

Service

Chassis Name: TPF 1.4U LA

26MF605W/17

MF605W/17

Horizontal frequencies

30-50kHz

TABLE OF CONTENTS

Description Page Important Safety Notice---- ------------------------------ 2 Technical Data-------------------------------------------3~4 Instalation/On Screen Display------------------------5~7 Troubleshooting--------------------------------------------8 Lock/unlock,Aging,Factory mode-----------------------9 Circuit Description-----------------------------------10~11 Mechanical Instructions----------------------------12~13 Definition of pixel defects -------------------------------14 Warning Message ----------------------------------------15 Electrical instruction --------------------------------16~20 DDC Instructions & Serial NO definition---------21~27 Failure mode of panel------------------------------------28 Safety Test Requirments--------------------------------29 ISP Instructions --------------------------------------30~32 Repair tips---------------------------------------------33~34 Color adjustment-------------------------------------35~36

SAFETY NOTICE

ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.

Description Page Repair Flow chart-----------------------------------37~38 Block Diagram---------------------------------------39~40 Wiring Diagram------------------------------------------41 Scaler Diagram&C.B.A. ---------------------------42~58 Power Diagram & C.B.A. --------------------------59~62 HD Diagram & C.B.A. ------------------------------63~65 IR Diagram & C.B.A. -------------------------------66~68 Key Diagram & C.B.A. -----------------------------69~70 Side AV Diagram & C.B.A. ------------------------71~73 Exploded View------------------------------------------- 74 Spare/recommended parts list ------------------75~79 General product specification--------------------80~97 DDC DATA------------------------------------------98~103 Different parts list--------------------------------------104 Difference between new and initial power PCB--105 Updated for new panel--------------------------------107

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.

REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES

K Feb. 08 2006

3138 106 10446

26MF605W/17

Important Safety Notice

Go to cover page

Proper service and repair isimportant to the safe, reliable

operation of all HPConsumer Electronics Company**

Equipment. The service procedures recommended by HP and

described in this service manual are effective methods of

performing service operations. Some ofthese service

operations require the use of tools specially designed for the

purpose. The special tools should be used when and as

recommended.

It is important to note that this manual contains various

CAUTIONS and NOTICES which should be carefully read in

order to minimize the risk of personal injury to service

personnel. The possibility exists that improper service

methods may damage the equipment. It is also important to

understand that these CAUTIONS and NOTICES ARE NOT

EXHAUSTIVE. HP could not possibly know, evaluate and

advise the service trade of all conceivable ways in which

service might be done or of the possible hazardous

consequences of each way. Consequently, HP has not

undertaken any such broad evaluation. Accordingly, a

servicer who uses a service procedure or tool which is not

recommended by HP must first satisfy himself thoroughly that

neither his safety nor the safe operation of the equipment will

be jeopardized by the service method selected.

* * Hereafter throughout this manual, HP Consumer

Electronics Company will bereferred to as HP.

WARNING

Critical components having special safety characteristics are

identified with a bythe Ref. No. inthe parts list and

enclosed within a broken line*

(where several critical components are grouped in one area)

along with the safety symbol on the schematics or

exploded views.

Use of substitute replacement parts which do not have the

same specified safety characteristics may create shock, fire,

or other hazards.

Under no circumstances should the original design be

modified or altered without written permission from Philips.

Philips assumes no liability, express or implied, arising out of

any unauthorized modification of design.

Servicer assumes all liability.

*BrokenLine

FOR PRODUCTS CONTAINING LASER :

DANGER- Invisible laser radiation when open.

AVOID DIRECT EXPOSURE TO BEAM.

CAUTION- Use of controls or adjustments or

performance of procedures other than

those specified herein may result in

hazardous radiation exposure.

CAUTION- The use of optical instruments with this

product will increase eye hazard.

TO ENSURE THE CONTINUED RELIABILITY OF THIS

PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S

REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART

NUMBERS IN THE PARTS LIST SECTION OF THIS

SERVICE MANUAL.

Take care during handling the LCD module with backlight

unit

- Must mount the moduleusing mounting holes arranged infour

corners.

- Do not press onthe panel, edge of theframe strongly or electric

shock as this will result in damage to the screen.

- Do not scratch orpress on the panel withany sharp objects, such

as pencil or pen asthis may result in damage to the panel.

- Protect the module fromthe ESD as it maydamage the electronic

circuit (C-MOS).

- Make certain that treatment person s body are grounded through

wrist band.

- Do not leave themodule in high temperature andin areas of high

humidity for a long time.

- Avoid contact with water as it may ashort circuit within the module.

- If the surface ofpanel become dirty, please wipe it off with a soft

material. (Cleaning with a dirty or rough cloth may damage the

panel.)

Technical Data

26MF605W/17

Go to cover page

LCD panel

Type NR. : )

line

Out dimensions : 626.0(H) x 373.0(V) x 44.1(D) mm (Typ.) Pitch (mm) : 0.4215(H) x 0. (V) Pixel format : 1 hori. By 7 vert. pixels Color pixel arrangement: RGB vertical stripe Display surface : Anti-glare

Number of color : ( bits) Backlight : FL Active area (WxH) : View angle

Contrast ratio : Typical : 1

L of white 500 cd/m Center 1 points, Typ.

uminance : ( ) AC-input : 90V ~ 264V Power consumption : W

Power cord length : 1.8M Power cord type : 3 lead with earth plug , plugable (US type) Power indicator : LED (On: Green ,Sleeping mode: Amber ) Auto power saving : EPA, Nutek, VESA DPMS Horizontal scan : 30 KHz Vertical scan : 56 Hz

Display mode : Multi-modes

Horizontal scanning

Vertical scanning

White balance Adjustment

Note: Use Minolta CA-110 for color coordinates and luminance check.

Normal X (center) = 0.289 ± 0.030

(8500 ° K CIE Coordinates) Y (center) = 0.304 ± 0.030

LC260WX2 (Supplier LPL

366 68

Hard coating(3H), treatment of the front polarizer

16,777,216 colors 8

18 EE

575.769mm x 323.712mm

: Viewing angle free(R/L 176(Typ.),

U/D 176(Typ.))

70 /Typ(at PC mode),105W/Typ(at TV

mode).

~50 ~63

Sync polarity : Positive or negative Scanning frequency : 30 ~ 50 KHz

Sync polarity : Positive or negative Scanning frequency : 56 ~ 63 Hz

4215

600

AC,50/602Hz

Pin No. Description

1RX22RX2+ 3GND 4GND 5GND 6 DDC clock 7 DDC data 8GND

9RX110 RX1+ 11 GND 12 GND 13 GND 14 +5V 15 DVI-D self test 16 +5V 17 RX018 RX0+ 19 GND 20 GND 21 GND 22 GND 23 RXC+ 24 RXC-

Environmental conditions

Operating

- Temperature : 0 to 40

- Humidity : 10 to 95%(non - condensing)

- Altitude : 0 to 12000 feet

- Air pressure : 600 to 1100 mBAR

- (guaranteed optical performance) : 5 to 35

- (guaranteed functional performance) : 5 to 40

Storage

- Temperature : -20 to 50

- Humidity : 10 to 95% (non - condensing )

- Air pressure : 600 to 1100 mBAR

Note:recommendat0to35°C, Humidity less than 60 %

Pin Assignment

Pin No.

2 3

Input DVI-D connector pin

Assignment

Red video input

Green video input

Blue video input

GND

Cable detect

Red video GND

Green video GND

Blue video GND

Pin No.

9 10

Assignment

DDC +3.3V OR +5V

GND

Serial data line (SDA)

H-sync

V-sync

Data clock line (SCL)

Shipping

- Temperature :( -20 to 50

- Humidity : 10 to 95% (non - condensing )

- Altitude : 0 to 40000 feet ( non operating )

- Air pressure : 600 to 1100

Marking and identification

In accordance with UAN-D1109 and the approval marking required by the countries of destination.

Safety and EMI requirements

Safety requirement: CSA C22.2 NO.950-95, UL1950, UL, CSA, NOM Ergonomic Requirement: TUV/GS, TUV/ERG, ISO13406-2 And the relevant national safety standards.

EMI requirement : FCC Part 15 Class B, ICES-003

Power Management: EPA

Electr ical c harac teri sti cs an d perfo rman ce

Test signal and test method in accordance with test instructions sheet

161 of the product where applicable.

Input signals

a. Analog Video : 15 pin D-Sub 0.7 Vp-p linear, positive

polarity and separate Sync ( TTL level,

positive or negative polarity ) b. Audio signal : Mini-jack audio input c. Signal source : Pattern generator format as attachment (

Timing table 1 to 6 ) d. Reference generator : CHROMA 2135 or 2250

)

26MF605W/17

Technical Data(Continued)

Go to cover page

TV Signal type :

Signal type Video signal Audio signal

Video1/Video2/

Video3

S-Video1/

S_Video2

Component InputRCA Jack, Y, Pb , Pr,

PVR Output (CVBS include Tuner)

DVI IN Digital TV signal support

HD IN Input RCA Jack, Y, Pb, Pr

RF IN Aerial Input

Headphone Output 3.5mm stereo jack

Front/Top control panel definition:

Power SW : Power switch.

Power LED : Normal operationàGreen.

+Up/Down- : Channel up and down, and OSD cursor up and down.

-Left/Right+ : Volume up and down, and OSD cursor left and right Menu : Enable and EXIT OSD menu(enter key for PC). IR receiver : Sense the signal from RC handset.

Input RCA Jack, Yellow Share with S-Video or Component

RCA Jack , White / Red

Input S-terminal, Black Share with Video1/Video2

RCA Jack, white / Red

Share with Video3

Green, Blue, Red

RCA Jack , Yellow

HDCP DVI connector

Green, Blue, Red

Sleeping modeàAmber.

RCA Jack, white / Red

Output (CVBS audio)

RCA Jack, white / Red

Input, L/R RCA Jack,

white / Red

Input, L/R RCA Jack,

white / Red

Remote control unit definition

Function Keys

The remote control is used in all PC and TV modes:

At PC mode function keys:

1. Press MENU Key to call Monitor Menu

2. Press Up/Down/Left/Right Key to select Monitor function

3. Left/Right is Volume Hot Key.

4. Use remote controller to control all PC menu function.

At TV mode function keys:

1. Press MENU Key to display TV Menu

2. Press Up/Down/Left/Right Key to select TV function

3. Up/Down Key is Channel Hot Key.

4. Left/Right Key is Volume Hot Key.

5. Use remote controller to control all TV menu function.

Display (for preset mode only)

Actual display size: 575.769mm X 323.712mm Resolution Factory Preset modes (6 modes)

Dot rate (MHz) H.freq (KHz) Mode Resolution V.freq (Hz)

25.175 31.469 IBM VGA 640 * 480 59.94

36 35.156 VESA 800 * 600 56.25

40.00 37.879 VESA 800 * 600 60.316

65.00 48.363 VESA 1024 * 768 60.004

CVT 74.5 47.772 WXGA 1280 * 720 59.855

CVT 79.5 47.776 WXGA 1280 * 768 59.87

Brightness output (Video signal 0.7V ± 2%)

Apply a 1280X768@60Hz signal with full white pattern, the center of screen at original color brightness light output is

Brightness control Contrast control Light output Unit: nit

100% 100%

> 400

Installation

26MF605W/17

Go to cover page

Top Control

Volume

Front Control

Power SW

<A>

LED

RC sensor

RightLeft

Channel

Key Function VGA mode TV/video mode

<A> Power DC Power DC Power

<B> Left Left/Volume down Left/Volume down

<C> Right Right/Volume up Right/Volume up

<D> Menu Enter /Exit OSD menu Enter /Exit OSD menu

<E> Menu Down/channel down Menu line Down Menu Down/Channel Down <F> Menu Up/Channel up Menu line Up Menu Up/Channel up

UpDown

26MF605W/17

Go to cover page

Installation

OSD Menu list

PC Signal control via front keyboard:

On Screen Display

TV Signal control via front keyboard :

Picture

Smart picture : Personal/Movie/Sport/weak signal/multimedia/

Brightness : Adjust brightness Color : Adjust color saturation Contrast : Adjust contrast. Sharpness : Adjust sharpness Tint : Adjust skin color

Audio

Smart sound : Personal/News/Music/Theatre Setting : Treble/base/balance adjustment Stereo : Stereo/mono select Virtual surround: Virtual surround on/off AVL : Auto volume limit on/off

Night

26MF605W/17

Go to cover page

Picture

Smart picture :Normal, warm, cool Brightness :Adjust backlight Contrast : Adjust contrast. Auto adjust : Yes/no for PC auto alignment. Manual adjust : Phase/clock/Horizontal/vertical

Audio

Smart sound : Personal/News/Music/Theatre Setting : Treble/base/balance adjustment Stereo : Stereo/mono select Virtual surround: Virtual surround on/off

AVL : Auto volume limit on/off

Featu re

PIP : Size (small/medium/large/PBP);

Video (TVàVideo1àVideo2àVideo3à

S-Video1à S-Video2àComponentàTV )

Audio (PIP/PC) Display (to change PIP display position)

Source : PCàDVIàTVàVideo1àVideo2àVideo3à

S-Video1àS-Video2àComponentàHDà PC

Install

Language : English/ Espanol / Francias Factory reset : Recall Contrast, Brightness.

Feature

Source : TV/Video1 / Video2 / Video3 / S-Video1/

S-Video2/Component/HD/PC/DVI/TV.

Picture format : WIDESCREEN / 4:3/ ZOOM 16:9 / SUPER

WIDE /

Auto lock : Lock program/change code/clear all/block

option/movie rating/TV rating.

Close caption : caption mode (CC1;CC2;CC3;CC4;TXT1;TXT2;

TXT3;TXT4;CC mute)

CC display (CC on/off)

Color Temp : Normal/warm/cool

Ins tall

Language : English/ Espanol / Francias Tuner mode : Antenna/cable/auto.

Auto program: Start

Channel edit : Channel(select channel)/Skipped(skip/

active).

Factory reset : Yes

26MF605W/17

Troubleshooting

Go to cover page

No Power

1. Check the TV power cord. Disconnect the power cord from the power outlet for 10 seconds, then reinsert the plug into the outlet. Press POWER to turn on the TV again.

2. Make sure the outlet is not on a wall switch.

3. Make sure a fuse has not blown at the power outlet.

No Picture

1. Check the antenna or Cable TV connections. Connect the antenna or Cable TV signal securely to the TV s 75 jack on the rear of the TV.

2. Set TUNER MODE correctly. Details are on page 18.

3. Activate AUTO PROGRAM to find all available channels. Details are on page 19.

4. In case you hear only sound and don have connected Video signal to S-Video or Video (CVBS) input. Only one of the two video inputs can be connected to sound. This means that the same sound can be heared in S-Video and Video (CVBS) mode.

t see any picture in S-Video or Video (CVBS) mode. Please check if you

No Sound

1. Press the VOL+ and VOL- buttons to adjust the volume.

2. Press the MUTE button on the remote control to cancel or restore the volume.

3. If you have connected other equipment to the TV (such as a VCR or DVD Player), make sure the audio cables are connected securely between the TV and the other equipment.

4. Check the SOUND settings. Details are on page 22 or 24.

5. In case you hear wrong sound in S-Video or Video (CVBS) mode. Please check if you have connected the right sound signal to AV in (S-Video or Video input). Only one of the two video inputs can be connected to sound, but both video signals can be connected. This means that only one of the two sound inputs can be heared in S-Video and Video (CVBS) mode.

Remote Control does not work.

1. Check the batteries. If necessary, replace them with two AAA heavy duty (zinc chloride) or alkaline batteries.

2. Clean the remote control as well as the remote control sensor on the front of the TV.

3. Check the TV power cord. Disconnect the power cord from the power outlet for 10 seconds, then reinsert the plug into the outlet. Press POWER to turn on the TV again.

4. Make sure the outlet is not on a wall switch.

5. Make sure a fuse has not blown at the power outlet.

6. Always point the remote control toward the front of the TV (toward the remote sensor).

7. Make sure that you use the supplied Magnavox Remote control, only the supplied Magnavox Remote control canbeusedwiththisLCD-TVset.

TV displays wrong channel or no channels.

1. Repeat channel selection.

2. Add the channel number(s) into the TV

3. Make sure TUNER MODE is set correctly. Details are on page 18. Then activate AUTO PROGRAM to set up all available channels. Details are on page 19.

s memory. Use STORE. Details are on page 20.

Poor Sound

1. Check if AVL (audio settings menu) is switched on [yes].

2. Select personal smart sound mode and optimize in the Audio onscreen menu the treble and bass settings.

3. Make sure that your external device, for instance VCR, DVD or other AV device has a good quality sound output.

Noisy Picture

1. Select the Weak signal Smart Picture Mode, in this mode noise from bad quality video signals will be suppressed.

Top Control

Aging and Factory Mode

26MF605W/17

Go to cover page

Volume

Left

Right

Channel

UpDown

Front Control

Power SW

<A>

AGING MODE No signal input ,power off -> on ,then Into the factory mode, , a full white pattern will be display on the screen as Fig.1&Fig.2 in stead of power saving mode. In other words, the power saving function will be disable in the factory mode.Supply one signal for leaving aging mode.

LED

RC sensor

Fig.3

Scalar Gain R G B Scalar Gain for Normal/Warm/Cool in PC

mode.

Auto-Color Adjust color from received signal (either

in PC or HDTV mode). ADC Offset R G B Adjust AD 9883 for PC ADC offset. ADC Gain R G B Adjust AD 9883 for PC ADC gain. PC Offset R G B PC analog scalar offset. 711X SDTV Brightness Adjust SA 7119 SDTV brightness. 711X SDTV SAT. Adjust SA 7119 SDTV saturation. 711X SDTV Contrast Adjust SA 7119 SDTV contrast. 711X SDTV TINT Adjust SA 7119 SDTV tint (hue). TV Shift H V Adjust TV screen position

horizontally/vertically. HD Shift H V Adjust HDTV screen position

horizontally/vertically. Show Lock Message Show OSD lock message. HDTVADCOffsetRGB AdjustAD9883forHDTVADCoffset. HDTVADCGainRGB AdjustAD9883forHDTVADCgain. Video Scalar Gain R G B Adjust scalar gain for Video mode. Scalar Hue Adjust scalar hue.

Fig.1

Fig.2

Access Factory Mode

1). Turn off monitor.

2). Press power "Power " button.Then quickly push " Volume -" and " Volume ",and hold this two buttons , then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second untill comes out "Windows screen"] => then release this two buttons, then press "Menu" button, wait until the OSD menu with Characters "F1/FL1 NAFTA V0.91.1 041124ADJUST" (below OSD menu) come on the Screen of the monitor (see Fig. 3).

Fig.4

26MF605W/17

Circuit Description

Go to cover page

General Description

This LCD TV monitor using FL-1 platform. It can support PC analog signal ( via 15 pin D-Sub input ) and TV signal. It support PIP

function that is TV picture on PC graphic or TV picture on DVI /HDCP. It’s output resolution is up to 1366X768 75Hz for WXGA panel.

It can support DVI HDCP digital signal input and also support TV (RF) , CVBS/ RG B signal ( from SCART1 I/O for Europe model ) , CVBS / YC ( from SCART2 I/O for Europe model ) , CVBS/YPbPr ( from Cinch I/O for Non-Europe model ) , CVBS/YC ( from Cinch and S terminal I/O for Non-Europe model ) , and also have side I/O , support CVBS/YC and Headphone for User easy used .

And It can also support Y Pb Pr signal input (from Cinch I/O) for 480I, 480P, 720P, 1080i 60Hz and 576I, 576P, 720P, 1080I 50Hz HDTV format input.

Note : For Chinch I/O model two components input is provided one for 480I,480P and 576I, 576P the other for the 480I, 480P, 720P,

1080i 60Hz and 576I, 576P, 720P, 1080I 50Hz HDTV format input.

It also have PVR output function , support and monitor all the CVBS signal output with L/R sound.

This LCD monitor TV use MST51512 as Scaler engine, which has embedded Analog D-sub, digital DVI decoder, scaling input signal for panel, OSD and simple 3D de-interlace. The extra SDRAM is to accomplish video frame rate conversion and PIP function.

The external CPU can be used for back light control, RC receiver, keypad input, I/O switch control , IIC communication and TV tuning control, MSP34XX sound decoder control, SAA7119 video decoder control , Columbus IC ( 3D- comb filter ) control , and Audio AMP TPA3004D sound control .

Video decoder SAA7119 is used for TV video processing and convert it with CCIR 601/16bits or 656/8bits digital format and send to Columbus IC for 3D comb filter processing and noise reduction processing , after that then send to Scaler for de-interlace process.

One audio decoder MSP34XXG is used for TV sound processing, and output to Class D audio amplifier TPA3004D , then we can have 2 X10W audio output .

In Nafta model CC,V-chip data is decoded in SAA7119 and the scaler OSD display the CC information. The V-Chip is decode by SAA7119 and control via the MCU. In Europe model "Teletext display". Data decode is done by SAA5360, output RGB/FB is to video decoder input for text overlapping. In non-text model( Nafta. Etc.), this chip is Not used .

Sound decoder

MSP34XX

DVI HDCP

PC analogTuner CVBS

SDRAM

1Mx16

Columbus

DDC

AUDIO delay

Scaler

MST51512

Audio

AMP

TPA3004D

LVDS

Panel

Tuner

video

audio

SC1-audio SC2-audio

audio DVI Audio

PC audio

HD YPbPr

RGB/YPbPr

AV3 audio HD audio

2ndIF

M U X

SC2 YC , AV3 YC

SC1/SC2/AV3 CVBS

CVBS MON_OUT

Video Decoder SAA7119

RGB/FB

SAA5360

SDRAM

1Mx16

MCU 128K Flash

Control Board

IR and key pad

Circuit Description

26MF605W/17

Go to cover page

MM tuner is used to receive RF wave and output CVBS and 2nd IF signal. CVBS is to video decoder (SAA7119) for color process, 2nd IF is to sound decoder (MSP34x5) for audio process. The tuner control is via IIC ex. channel tuning. For different TV system, tuner and sound decoder have diversity as above. Standard TV input (Tuner, S-video, CVBS, SCART) is processed by SAA7119, But YPbPr, SDTV and HDTV(480i, 576i, 480p,576p,720p,1080i), is done by scaler MST51512L/502L ADC. But the signal is still link to SAA7119 if PIP (video in graph) function is requested. Then all YPbPr signal processed by SAA7119 could be the PIP video source. (* May use down sampling in HD0) MV protect is decoded by scaler. Video decoder SAA7119, is in charge of color decoding, could support PAL, NTSC and SECAM world wide system. Compare to SAA7118, SAA7119 improve some picture quality, like V-chip CC I2C read-back, LTI, CTI, skin tone correction(see task A), also the HD0 is supported, so if F1 need PIP function then the The Teltext function is for WE model, need a extra IC SAA5360. CVBS input, R/G/B, FB, out. Due to the SAA5360 request input signal 1Vrms and only one input channel, so the CVBS input source is from SAA7119 AOUT (CVBS out with 1Vrms). The R/G/B FB output into SAA7119 by AI22/AI32/AI42, and AI44 could overlay on any video source. Sound decoder MSP3415/45 is responsible to sound decode of tuner 2nd IF. It has one 2nd IF, two selectable audio sources input. And one loudspeaker, one scart out. Due to the input port limitation, a MUX is added for AV source select( PC audio in is fix in SC1). If the post audio amplifier is gain fixed type then the volume adjust will be on MSP34x5. Scaler MST51502L/51512L besides scaling function, PIP, 3D de-interlacer, color enhance are major feature. Even de-interlacer is not so good but for static picture is enough to avoid image sticking. In America market, to avoid patent issue, two SDRAM is necessary for graph frame buffer. But in else region one SDRAM is enough. Of course, if no PC mode in spec, then one SDRAM for all model. The scaler structure limitation, the PIP source only from video port,8bitsor16bits. The sub window /PIP size can enlarge to half screen. MCU, NT68F632AL, is 128K flash ROM inside. Power control, RC5 I/O, and key function all done by here. All chip communication is by IIC (SDA/SCL), and ISP is via DDCIIC, but if PC mode un-supported, then a reserved 6pin connector is for same application.

26MF605W/17

Go to cover page

Front view

Mechanical Instruction

Back view

Step 1. Remove the stand.

Remove the three screws as Fig.3 and Fig.4

Fig.1

Fig.2

Fig.6

Fig.7

Fig.8

Fig.9

Fig.3

Step 2. Remove the Back cover as Fig.5~8.

Remove the seven screws on the sides and the other

two screws as Fig.5

b. Use thin "I" type screwdriver to open 4 clicks on bottom

side as Fig.6

Use thin "I" type screwdriver to open 3 clicks on right

side as Fig.7

e. Use thin "I" type screwdriver to open 3 clicks on left

side as Fig.8

f. Use thin "I" type screwdriver to open 4 clicks on top

side as Fig.9

g. Remove the back cover as Fig.10 ,then remove the

10 screws as Fig.10,Fig.11,Fig.12

Fig.4

Fig. 10

Fig. 11

Fig. 12

Step 3. Remove the Scaler and Power board.

Remove the 19 screws and disconnect the 9 cables as Fig. 13 and Fig.14

Fig.5

Fig. 13

Mechanical Instruction

Fig. 16

26MF605W/17

Go to cover page

Fig. 14

Step 4. Disconnect the HD PCB, the Side AV PCB, the KEY PCB , the

IR PCB, as Fig.15the Scaler PCB and power PCB

Fig. 15

Step 5 Remove the MAIN SHIELD ASSY as Fig.16~Fig.18

Remove the 16 screws on the back side as Fig.16

b. on bottom side as Fig.17

Remove the 2 screws

c . on top side as Fig.18

Remove the 2 screws

d. Disconnect the MAIN SHIELD ASSY as Fig.19

Fig. 17

Fig. 18

Fig. 19

In warranty, it is not allowed to disassembly the LCD panel, even the

backlight unit defect.

Out of warranty, the replacment of backlight unit is a correct way

when the defect is cused by backlight (CCFL,Lamp).

26MF605W/17

Definition of Pixel Defects

Go to cover page

LCD Monitor Quality and Pixel Policy

The TFT monitor uses high-precision technology, manufactured according to HP standards, to guarantee

trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small

bright or dark spots.

This is common to all LCD displays used in products supplied by all vendors and is not specific to the HP LCD.

These imperfections are caused by one or more defective pixels or sub-pixels.

1. A pixel consists of one red, one green, and one blue sub-pixel.

2. A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off (a dark spot

on a bright background). The first is the more visible of the two.3. A defective sub-pixel (dot defect) is less

2. visible than a defective whole pixeland is small and only visible on a specific background.The HP display does

not have more than:

4. bright dots.

5. dark dots.

6. total bright and dark dots.

7. No more than two adjacent (less than 2.5 mm edge-to-edge) defective pixels. To locate defective pixels, the monitor

should be viewed under normal operating conditions, in normal operating mode at a supported resolution and

refresh rate, from a distance of approximately 50 cm (16 in.).HP expects that, over time, the industry will continue to

improve its ability to produce LCDs with fewer cosmetic imperfections And HP will adjust guidelines as

improvements are made.

Warning Message

26MF605W/17

Go to cover page

1.Automatic adjustment (for factory only)

Press Volume+ and Volume- on front key at the same time (PC mode only). It adjusts PC image to the best and save the screen automatically.

2.OUTOFRANGE

If PC input timing is out of range, it shows OUTOFRANGE warning message on the center of the screen. range of horizontal frequency is between 14 - 63 KHz. The range of vertical frequency is between 45 The OSD won

t timeout.

3.NO VIDEO INPUT

When PC input timing has either horizontal frequency or vertical frequency. Or neither has horizontal frequency nor vertical frequency. It shows on the center of the screen for 30 seconds, then it will enter sleep mode.

26MF605W/17

Go to cover page

Electrical Instructions

1. General points

1.1 During the test and measuring, supply a distortion free AC mains voltage to the apparatus via an isolated transformer

with low internal resistance.

1.2 All measurements mentioned hereafter are carried out at a normal mains voltage (90 - 132 VAC for NAFTA version,

195 -264 VAC for EUROPEAN version, or 90 - 264 VAC for the model with full range power supply, unless otherwise stated.)

1.3 All voltages are to be measurement or applied with respect

to ground, unless otherwise stated.

1.4 The test has to be done on a complete set including LCD

panel in a room with temperature of 25 +/- 5 degree C.

1.5 All values mentioned in these test instruction are only

applicable of a well aligned apparatus, with correct signal.

1.6 The letters symbols (B) and (S) placed behind the test

instruction denotes

(B): carried out 100% inspection at assembly line (S): carried out test by sampling

1.7 The white balance (color temperature), has to be tested in

subdued lighted room.

1.8 Repetitive power on/off cycle are allowed except it should

be avoided within 6 sec.

2. Input and output signal

2.1.1 PC Signal type

Analog Video : 15 pin D-sub ,0.7 Vp-p linear, positive polarity

Separate Sync.: TTL level, separate, positive or negative polarity

Audio signal : 3.5mm stereo mini-jack

Level : -Nominal : 0.5 V rms.

- Maximum : 1.5 V rms.

-Impedance > 10 k W. Signal source: pattern generator format as attachment

(table 1 to 5 ) Reference generator : CHROMA 2200 or 2250

2.1.2 TV Signal type

RF Signal : Aerial input / 10mV(80dBuV)

Video signal : Video( RCA jack, CVBS input) / 1Vpp (300mV-sync,

700mV-video.) S video input / 1VppY-signal, 300mVpp C-signal

COMP Video( RCA jack , YPbPr input) / 1Vpp Y signal ,

350mVpp Pb , Pr signal

DVI : Digital interface with 4 channels TMDS signal

Audio signal : Audio (1) R/L( RCA jack ) for AV IN1 ( share with

Video and S-video1 ). Level: - Nominal : 0.5 V rms.

- Maximum : 1.5 V rms.

- Impedance > 10 k W. Audio (2) R/L( RCA jack ) for AV IN2 (share with

Video2 and S-video2).

Level: - Nominal : 0.5 V rms.

- Maximum : 1.5 V rms.

- Impedance > 10 k W. Audio (3) R/L ( RCA jack )for AV IN3 (share with

Video3 and Comp video).

Level: - Nominal : 0.5 V rms.

- Maximum : 1.5 V rms.

- Impedance > 10 k W. Audio (4) R/L( RCA jack ) for DVI IN.

Level: - Nominal : 0.5 V rms.

- Maximum : 1.5 V rms.

- Impedance > 10 kW.

2.1.3 PVR output (CVBS output): Video: CVBS output 1Vpp / Impedance : 75W.

Audio: R/L output (from CVBS)

Level: - Nominal : 0.5 V rms.

- Maximum : 1.5 V rms.

- Impedance < 1 kW.

2.1.4 Headphone

Audio: R/L output -10mW at 32W.

3.5mm stereo jack with switch

Impedance is between 8 and 600W.

2.2 PC Input si gnal mode

2.2.1 PRESET VIDEO RESOLUTION

The analogue color LCD monitor must be capable of displaying

standard resolutions within the vertical frequency range of

58 - 63 Hz, and horizontal scan range of 30 - 50 KHz .

Use the CHROMA-2250 generator as the standard signal timing

source.

Dot rate (MHz) H.fr eq

(KHz)

1 25.175 31.469 IBM VGA 640*480 59.940

2 36.000 35.156 VESA 800*600 56.250

3 40.000 37.879 VESA 800*600 60.317

4 65.000 48.363 VESA 1024*768 60.004

5 74.500 44.772 WXGA 1280*720 59.855 CVT

5 79.500 47.776 WXGA 1280*768 59.87 CVT

Resolution recommend on 1280 X 720 @ 60Hz

Mode Resolution V.freq

(Hz)

Remar k

2.3 TV in put signal Channel and pattern for NAFTA model (Table1)

Signal Distribution Table (NTSC)

A03 61.25MHz 65.75MHz NTSC M Color Circle

A06 83.25MHz 87.75MHz NTSC M Red Raster

A09 187.25MHz 191.75MHz NTSC M Circle Pattern

A11 199.25MHz 203.75MHz NTSC M Cross Hatch

A13 211.25MHz 215.75MHz NTSC M

A52 699.25MHz 703.75MHz NTSC M Color Bar

A69 801.25MHz 805.75MHz NTSC M 100% White

C70 499.25MHz 503.75MHz NTSC M Checkerboard

Table 1

Frequenc y Car riers

Video Sound

TV System

Pattern

Two White

Window

Electrical Instructions

26MF605W/17

Go to cover page

2.4 HD input mode

2.4.1 HD detail timing (For Quantune Data setting with Q801GD or 802G in YpbPr mode)

Item

Pixel rate 74.25MHz

Horizontal Frequency Active 1920

Blank 280 pixels

Period 2200

Pulse delay 44 pixels

Pulse width 44 pixels

Vertical Frequency Active 1080 lines

Blank 45 lines

Period 1125 lines

Pulse delay 2 lines

Pulse width 5 lines

EQ before 0 line 0 line 0 line 0 line EQ after 1 line 0 line 1 line 0 line Scan Interlace ProgressiveInterlace Progressiv

Sync type ACS ACS ACS ACS Video kind Analog

1920X108 0i 60Hz

(13.468 ns)

33.75KHz 45KHz 28.125KHz37.5KHz

pixels

(25.859

us)

(3.771 us)

pixels

(29.630

us)

(0.593 us)

60 Hz 60 Hz 50 Hz 50 Hz

(32.000

ms)

(1.333

ms)

(33.333

ms)

(0.059

ms)

(0.148

ms)

YPbPr (ITU-R BT.709)

1280X720 P 60Hz

74.25MHz (13.468 ns)

1280 pixels

(17.239 us) 370 pixels

(4.983 us)

1650 pixels

(22.222 us)

70 pixels

(0.943 us)

40 pixels

(0.539 us)

720 lines

(16.0 ms)

30 lines

(0.667 ms) 750 lines

(16.667 ms)

5 lines

(0.111 ms ) 5 lines

(0.111 ms)

Analog YPbPr (ITU-R BT.709)

1920X108

0i50Hz

74.25MHz ( 13.468ns

)

1920 pixels

(25.859 us) 720 pixels

( 9.697 us ) 2640 pixels

( 35.556 us )

484 pixels

( 6.519 us ) 44 pixels

( 0.593 us )

1080 lines

( 38.4 ms ) 45 lines

(1.6 ms )

1125 lines

(40ms)

2 lines

( 0.071 ms ) 5 lines

(0.178 ms )

Analog YPbPr (ITU-R BT.709 )

1280X720 P50Hz

74.25MHz (13.468 ns)

1280 pixels

(17.239 us) 700 pixels

(9.428 us)

1980 pixels

(26.667 us)

400 pixels

(5.387 us)

40 pixels

(0.539 us)

720 lines

(19.2 ms)

30 lines

(0.8 ms)

750 lines

(20 ms)

5 lines

(0.133 ms ) 5 lines

(0.133 ms)

Analog YPbPr (ITU-R BT.709)

Item 720X576P

Pixel rate 27 MHz

Horizontal Frequency Active 720 pixels

Blank 144 pixels

Period 864 pixels

Pulse delay

Pulse width

Vertical Frequency Active 576 lines

Blank 49 lines

Period 625 lines

Pulse delay

Pulse width

EQ before 0 line 0 line 2 line 3 line EQ after 0 line 0 line 2 line 3 line Scan Progressive ProgressiveInterlace Interlace

Sync type ACS ACS ACS ACS Video kind Analog

50Hz

(37.037 ns)

31.25 KHz 31.5KHz 15.625KHz15.734KH

(26.667 us)

(5.333 us)

(32.000 us)

12 pixels

(0.444 us)

64 pixels

(2.370 us)

50 Hz 60 Hz 50 Hz 59.94 Hz

(18.432 ms)

(1.568 ms )

(20.000 ms)

5 lines

(0.160 ms)

5 lines

(0.160 ms)

YPbPr (SMP TE RP177)

720X480P 60Hz

27.027MH z (37.000 ns)

720 pixels

(26.640 us) 138 pixels

(5.106 us)

858 pixels

(31.746 us)

16 pixels

(0.592 us)

62 pixels

(2.294 us)

480 lines

(15.238 ms) 45 lines

(1.429 ms) 525 lines

(16.667 ms)

9 lines

(0.287 ms) 6 lines

(0.190 ms)

Analog YPbPr (SMPTE RP177)

Table 2

720X576i 50Hz

13.5MHz ( 74.074 ns )

720 pixels

(53.333 us) 144 pixels

( 10.667 us ) 864 pixels

( 64.00 us )

12 pixels

( 0.889 us ) 63 pixels

( 4.667 us )

576 lines

( 36.864 ms ) 49 lines

(3.136 ms ) 625 lines

(40ms)

2 lines

( 0.128 ms ) 3 lines

(0.192 ms )

Analog YPbPr (SMPTE RP177 )

720X480i 60Hz

13.5MHz ( 74.074 ns )

z 720 pixels

(53.333 us) 138 pixels

( 10.222 us ) 858 pixels

( 63.556 us )

19 pixels

(1.407 us ) 62 pixels

(4.593 us )

480 lines

( 30.507 ms ) 45 lines

(2.860 ms ) 525 lines

( 33.367 ms )

4 lines

(0.254 ms ) 3 lines

(0.191 ms )

Analog YPbPr (SMPT E RP177 )

3. Power supply

3.1 Setup the AC I/P at 264 VAC and 90VAC , and power board

3.2 Any adjustment is not needed.

provide two DC Output

1. The DC output voltage is 24V ± 1V DC for Inverter and Scaler board Measured point between pin3(+24V) and pin6(GND) at item 1001 of scaler board

2. The DC output voltage is 16V ± 1VDCforScalerand Audio board Measured point between pin1(+16V) and pin6(GND) at item 1001 of scaler board

4. TV Mode display adjust

4.1 White balance adjustment (B)

4.1.1 General set-up : Equipment Requirements: Color analyzer. Input requirements: Input Signal Type : RF signal

1. Set to NTSC system, frequency=187.25MHZ ( for NAFTA model ), with white pattern of 100%

26MF605W/17

Go to cover page

Electrical Instructions

2. Select Smart picture to Personal mode and check the x, y data. Input Signal Strength : 10mV (80 dBuV) terminal voltage.

Input Injection Point : TV Tuner input Alignment method:

Initial Set-up :

1.Set TV(7119) Brightness=142; Saturate =64, Contrast =68 in Factory mode(can be fine tuned).

2. Set Smart picture as

3. Apply 100% Full White pattern by TV pattern generator.

Alignment : Adjust the VIDEO SCALER GAIN RG B

Factory Mode

menu : press VOL+ and VOL- keys together around six

seconds]

1. Check (X, Y) co-ordinates as below:

Picture Mode Normal (Original)

Table 3: Reading with Minolta CA-110.

2. Check the gray pattern should be distinguish and

color bar is correct

4.1.2 Set TV Color temperature in Factory mode as and

COOL The VIDEO SCALER GAIN R\G\B value will be

followed below

Normal/ the R \G \B

are gain after alignment. WARM

R gain R R R -10

G gain G G -10 G -10

B gain B B -10 B

NORMAL . (See Fig 1.) [ Enter factory

0.289 ± 0.005 0.304 ± 0.005

Personal

WARM ,

COOL

5. PC mode Display Adjustment

5.1 Display quality adjustment

Use timing mode as describe in 2.2, and use the POPO (pixel on pixel

off) pattern to adjust the clock until no stripe and adjust the phase until

clear picture.

Check all pre-set 6 modes.

5.2 WHITE-D adju stm ent (B )

5.2.1 At factory mode apply 1280X720 @60Hz mode with 32 gray

pattern.

Set smart picture at

Contrast to 50%.

Press AUTO-COLOR function for auto ADC offset and gain setup.

5.2.2 Apply full white pattern Set SCALER GAIN R G B

SCALER GAIN R G B.

1. Check (X, Y) co-ordinates as below :

Normal/ (8500°K)

x (center) 0.289 ± 0.015

y (center) 0.304 ± 0.015

Table 4: Reading with Minolta CA-110.

2. Check the gray level color poor & noise condition and chromaticity

Note: 1. Use Minolta CA-110 for color coordinates and luminance check.

2. Luminance> 400 c d/m

Original (NORAML)color and PC Brightness control; Contrast

control at 100%

5.2.3 Set Smart picture as The SCALER GAIN R\G\B value will be followed below

Normal/ the R \G \B

are gain after alignment.

R gain R R R -10

G gain G G -10 G -10

B gain B B -10 B

5.3 Check t he di git al inter face cable (B )

Check the 64 gray level color poor & noise condition.

Normal , and Brightness to 50% and

= VIDEO

in the center of the screen at

WARM , and COOL

WARM COOL

6. HDTV Mode disp lay adjus t

6.1 White balance adjustment (B) General set-up: Equipment : Quantum Data Pattern Generator 801GD or 802G.

Or FLUKE 54200, apply 576i, DIGITAL SCAN/DIGI_ADC1 pattern.

Apply 1080i, RGBW(177=Infocus2) gray pattern.

Electrical Instructions

26MF605W/17

Go to cover page

Alignment method: Initial Set-up: 1.Set Smart picture as

Alignments : Set HD VIDEO SCALER GAIN R\G\B= TV

Check (X, Y) co-ordinates as below:

Picture Mode x y Personal

If chromaticity (X, Y) co-ordinates is out of specification, re-alignment Video scalar R/G/B gain from 127/127/127.

7. Preset DVI HDCP Key

7.1 Download HDCP Key

The 284 bytes HDCP key should be download to the TV set via

IF cable using ATE at factory Alignment tools

7.2 DVI Video HDCP Key Test

7.2.1Use pattern generator

Equipment: Quantum 802R or 802BT or equivalent equipments.

Pattern : Standard HDCP Pattern (It

Timing : 720 X 480P 60Hz

Result : The PASS information should be shown on the screen.

7.2.2 Use DVD Player:

Equipment: 1.Pioneer (model: DV-S969AVi) or equivalent equipments

Result : The picture should be shown Normally.

8. Preset EEPROM dat a

EEPROM data has to be preset data according following table.

8.1 Factory mode pr eset.

Funct ion SCALER GAIN ADC Off set R/G/B ADC Gain R/G/B PC OFFset R/G/B

7119 brightness 7119 Satur atio n #1

7119 contrast 7119 TINT

DVI SHIFT H DVI SHIFT V

TV sh ift H TV sh ift V

HD SHIFT H HD SHIFT V

HD ADC OFFs et R G B HD ADC GAIN R G B Video Sc aler Gain Scaler Hu e

Color=60, Contrast=65)

2.Press AUTO-COLOR process.

Normal VIDEO SCALER GAIN R G B.

1. Apply

2. Check the gray pattern should be

distinguish and color bar is correct

720 X 576P 50Hz

1280X 720P 50Hz

1280X 720P 60Hz

1920X1080i 50Hz

1920X1080i 60Hz

2.DVD disk with Macro Vision protection.

Regu lar

100% Full White pattern by Quantum

DATA 802G pattern generator.

0.289 ± 0.015 0.304 ± 0.015

Personal , Brightness=48,

s color bar)

Preset valu e

127 127 127 127 127 127

#2 #2

NTSC PAL

175 195

15 1 #3 #3

#3 #3 127 127 127 127 127 127

127 127 127

PERSONAL/

NORMAL

TV 139 64 60 24

AV 142 64 64 24

S-Video 142 64 64 24

Component 143 70 62 --

480P576P720P/

DVI shift H 22 22 96 55 103 48

DVIshiftV445040406060

480i480P576i576P720

HD shift H155 HD shift V

8.2 Smart picture & Smart sound:

8.2.1 Final TV mode out box setting. Smart Picture : Sport Color Temp in Factory mode : COOL Smart Sound : Personal

PERSONAL

MOVIES

SPORTS

WEAK SIGNAL

MULTIMEDIA

NIGHT

154 16716710814679 79

39 40 49 53 39 39 58 58

SOUND VOLUME : 10 BASE : 55 TREBLE : 55

Balance :0 Virtual SURROUND : OFF AVL : NO

SAT. TINT

50Hz

Smart Pi cture

BRIGHTNESS 45 COLOR 50 CONTRAST 65 SHARPNESS 38 TINT 50 BRIGHTNESS 59 COLOR 60 CONTRAST 51 SHARPNESS 36 TINT 50 BRIGHTNESS 48 COLOR 65 CONTRAST 75 SHARPNESS 46 TINT 50 BRIGHTNESS 52 COLOR 60 CONTRAST 51 SHARPNESS 46 TINT 50 BRIGHTNESS 52 COLOR 60 CONTRAST 68 SHARPNESS 33 TINT 50 BRIGHTNESS 45 COLOR 50 CONTRAST 65 SHARPNESS 38 TINT 50

720P/ 60Hz

P/50 Hz

720 P/60 Hz

1080i/ 50Hz

1080 i/50 Hz

1080i/ 60Hz

1080 i/60 Hz

26MF605W/17

Go to cover page

Electrical Instructions

EQ Settin g

PERSONAL

NEWS

MUSIC

THEATRE

Smart Sound

EQBAND1 120Hz +25 EQ BAND2 500Hz +25 EQ BAND3 1.5KHz +25 EQ BAND4 5KHz +25 EQ BAND5 10KHz +25 EQ BAND1 120Hz 0 EQ BAND2 500Hz 0 EQ BAND3 1.5KHz +20 EQ BAND4 5KHz +30 EQ BAND5 10KHz +40 EQ BAND1 120Hz +50 EQ BAND2 500Hz +35 EQ BAND3 1.5KHz +15 EQ BAND4 5KHz +30 EQ BAND5 10KHz +45 EQ BAND1 120Hz +50 EQ BAND2 500Hz +35 EQ BAND3 1.5KHz -5 EQ BAND4 5KHz +20 EQ BAND5 10KHz +40

DDC Instructions

26MF605W/17

Go to cover page

General

DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed "Analog DDC IC, Digital DDC IC & EEPROM". It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.

Additional information Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards Association (VESA). Extended Display Identification Data(EDID) information may be also obtained from VESA.

System and equipment requirements

1. An i486 (or above) personal computer or compatible.

2. Microsoft operation system Windows 95/98 . Y o Install the EDID_PORT_Tool under Win2000/XP . As

ou have t

Fig. 1 .

A. Cody the "UserPort.sys" to C:\WINNT\system32\drivers(win2000)

C:\WINDOWS\system32\drivers(winXP)

B. Running " io.exe" everytime, Before you start to programming

edid data .

Fig. 1

Note: The alignment box has already build-in a batteries socket for

using batteries (8~12V) as power source. Pull out the socket by remove four screws at the rear of box. Please do not forget that remove batteries after programming. The energy of batteries can only drive circuits for a short period of time.

To Printer port

DC 8~12V

To Monitor

D-sub/DVI cable

Power indicator

Fig. 3

Pin assignment

A. 15-pin D-Sub Connector

PIN No. SIGNAL

1 Red video input

2 Green video input / sync on green

3 Blue video input

4GND

5 GND - Cable detect

6RedvideoGND

7 Green video GND

8 Blue video GND

9DDC+3.3Vor+5V

10 Logic GND

11 GND

12 Serial data line (SDA)

13 H-sync / H+V

14 V-sync

15 Data clock line (SCL)

B. Input DVI -D Connector pin

3. EDID46.EXE program

4. A/D Alignment kits (12NC: 3138 106 10396): inclusion : a. Alignment box x1 (Fig. 2)

b. Printer cable x1

c. (D-Sub) to (D-Sub) cable x1

D. (D-Sub) to (DVI) cable x1

Fig. 2

Pin No. Description

1 T.M.D.S. data2-

2 T.M.D.S. data2+

3 T.M.D.S. data2 shield

4 No Connect

5 No Connect

6 DDC clock

7 DDC data

8 No Connect

9 T.M.D.S. data1-

10 T.M.D.S. data1+

11 T.M.D.S. data1 shield

12 No Connect

13 No Connect

14 +5V Power

15 Ground (for +5V) - Cable detect

16 Hot plug detect

17 T.M.D.S. data0-

18 T.M.D.S. data0+

19 T.M.D.S. data0 shield

20 No Connect

21 No Connect

22 T.M.D.S clock shield

23 T.M.D.S. clock+

24 T.M.D.S. clock-

26MF605W/17

Go to cover page

DDC Instructions

Configuration and procedure

There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores

all factory settings and DDC data (EDID code) which is also called Software DDC. The following section describes the connection and procedure for Software DDC application. The main EEPROM can be reprogrammed by enabling '' factory memory data write'' function on the DDC program (EDID46.EXE).

Initialize alignment box

In order to avoid that monitor entering power saving mode due

to sync will cut off by alignment box, it is necessary to initialize

alignment box before running programming software

(EDID46.EXE). Following steps show you the procedures and

connection.

Step 1: Supply 8-12V DC power source to the Alignment box by

plugging a DC power cord .

Step 2: Connecting printer cable and D-Sub cable of monitor as Fig. 4

TP1)

DC Power

8-12 V

1= Power connector 2= D-SUB connector

3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID46 (for example, C:\EDID46, as shown in Fig. 6).

Fig. 6

4. Click OK button. The main menu appears (as shown in Fig. 7). This is for initialize alignment box.

Fig. 5

----->

To printer port (

Step 3: Installation of EDID46.EXE

Method 1: Start on DDC program

Start Microsoft Windows.

1. The Program"EDID46.EXE" in service manual cd-rom be copyed to C:\ .

2. Click , choose Run at start menu of Windows as shown In Fig. 5.

Printer Port

To Monitor

To P C

Fig. 4

Fig. 7

Note 1: If the connection is improper, you will see the following error

message (as shown in Fig. 8) before entering the main menu.

Meanwhile, the (read EDID) function will be disable. At this

time, please make sure all cables are connected correctly and fixedly, and the procedure has been performed properly.

Fig. 8

Note 2: During the loading, EDID46 will verify the EDID data which just

loaded from monitor before proceed any further function, once the data structure of EDID can not be recognized, the following error message will appear on the screen as below. Please confirm following steps to avoid this message.

1. The data structure of EDID was incorrect.

2. DDC IC that you are trying to load data is empty.

3. Wrong communication channel has set at configuration setup windows.

4. Cables loosed or poor contact of connection.

Fig. 9

DDC Instructions

Re-programming Analog DDC IC

Step 1: After initialize alignment box, connecting all

cables and box as shown in Fig. 10.

TP1)

DC Power

8-12V

1=Power connector 2= D-S UB connector

----->

26MF605W/17

Go to cover page

Fig. 13

To printer port (

To PC Video port (D-sub)

Printer Port

To Monitor

To PC

Step 2: Read DDC data from monitor

1. Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 11.

=====>

Click this button

Fig. 11

2. Select the DDC2Bi as the communication channel. As shown in Fig. 12.

Fig. 10

Step 3: Modify DDC data (verify EDID version, week,

year)

Click (new function) icon from the tool bar, bring up

Step 1 of 9 as shown in Fig. 14 . EDID46 DDC application provides the function selection and

Select and fill out, If necessary.

Fig. 14

Fig. 12

3. Click OK button to confirm your selection.

4. Click icon (Read EDID function) to read DDC EDID data from

monitor. The EDID codes will display on screen as shown in Fig. 13.

Step 4: Modify DDC data (Monitor Serial No.)

1. Click Next , bring up Fig. 15.

Fig. 15

26MF605W/17

Go to cover page

DDC Instructions

2. Click Next , bring up Fig.16.

3. Click Next , bring up Fig.17.

5. Click Next , bring up Fig.19.

Fig. 19

Fig. 16

6. Click Next , bring up Fig. 20. In this step, please confirm the Descriptor Data Type is

Monitor Range Limits, and all the items are same as below.

4. Click Next , bring up Fig.18.

Fig. 17

Fig. 18

Fig. 20

7. Click Next , bring up Fig. 21.

Fig. 21

DDC Instructions

8. Click Next , bring up Fig. 22.

- Click Finish to exit the Step window.

- Serial number can be filled up at this moment (for example,

26MF605002).

NOTE: You must modify the Serial NO. In step 9, otherwise the Serial NO.

In OSDCouldn't be modified correctly.

Fig. 22

26MF605W/17

Go to cover page

4). Click (Write EDID) icon from the tool bar to write DDC data. then the screen will be black for 2-3 seconds,then the screen recovers, and "ATTENTION NO VIDEO INPUT"will come on the screen of the monitor,wait for 20-30 seconds ,DDC data will be finished Writing.

Step 6: Save DDC data

Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below:

1. Click (Save) icon (or click "file"-> "save as") from the tool

bar and give a file name as shown in Fig. 25.

The file type is EDID46 file (*.ddc) which can be open in

WordPad. By using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table ar completely correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC Data application.

Step 5: Write DDC data

1. Configuration should be as Fig. 23. And press OK.

2. Access Factory Mode

1). Turn off monitor.

2). Press power "Power " button.Then quickly push"Volume -" and " Volume ",and hold this two buttons,then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second ,untill comes out "Windows screen"] => then release this two buttons, then press "Menu"button, wait until the OSD menu with Characters "F1/FL1 NAFTA V0.91.1 041124ADJUST" (below OSD menu) come on the Screen of the monitor (see Fig. 24).

Fig. 23

Fig. 25

2. Click Save.

Step 7: Exit DDC program

Pull down the File menu and select Exit as shown in Fig. 26.

Fig. 26

Step 8: Turn off the monitor, exit the factory mode.

3) Push Menu to exit OSDmenu.""

Fig. 24

-----------------> Factory Mode

Indicator

26MF605W/17

Go to cover page

Re-programming Digital DDC IC

Step 1: After initialize alignment box, connecting all

cables and box as shown in Fig. 27.

1=DVI-D connector 2=D-sub connector

3=Power Plug

DDC Instructions

Select and fill out, If necessary.

DC Power

8 12V~

To video card

To printer port (LTP1)

Printer Port

D-sub to DVI-D cable

To Monitor

Step 2: Read DDC data from monitor

D-sub cable

Fig. 27

1. Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 28.

=====>

Click this button

Fig. 28

2. Select the DDC2Bi as the communication channel. As shown in Fig. 29.

Fig. 31

Step 4: Modify DDC data (Monitor Serial No.)

1. Click Next , bring up Fig. 32.

2. Click Next , bring up Fig. 33.

3. Click Next , bring up Fig. 34.

Fig. 33

4. Click Next , bring up Fig. 35.

5. Click Next , bring up Fig. 36.

Fig. 34

Fig. 32

Fig. 29

Fig. 30

3. Click OK button to confirm your selection.

4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 30.

Step 3: Modify DDC data (verify EDID version, week,

year)

Click (new function) icon from the tool bar, bring up

Step 1 of 9 as shown in Fig. 31 . EDID46 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9.

Fig. 35

6. Click Next , bring up Fig. 37.

In this step, please confirm the Descriptor Data Type is

Monitor Range Limits, and all the items are same as below.

7. Click Next , bring up Fig. 38.

Fig. 37

Fig. 36

Fig. 38

DDC Instructions & Serial NO Definition

8. Click Next , bring up Fig. 39.

- Click Finish to exit the Step window.

- Serial number can be filled up at this moment (for example, 26MF605002).

NOTE: You must modify the Serial NO. In step 9, otherwise the Serial

NO. In OSD Couldn't be modified correctly.

26MF605W/17

Go to cover page

Fig. 39

Fig. 40

Step 5: Write DDC data

1. Configuration should be as Fig. 40. And press OK.

2. Access Factory Mode

1). Turn off monitor.

2). Press power "Power " button.Then quickly push " Volume -" and " Volume ",and hold this two buttons,then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second ,untill comes out "Windows screen"] => then release this two buttons, then press "Menu" button, wait until the OSD menu with Characters "F1/FL1 NAFTA V0.91.1 041124ADJUST" (below OSD menu) come on the Screen of the monitor (see Fig. 41).

-----------------> Factory Mode

Indicator

2. Click Save.

Fig.42

Step 7: Exit DDC program

Pull down the File menu and select Exit as shown in Fig. 43.

Fig. 43

Step 8: Turn off the monitor, exit the factory mode.

Serial Number Definition

Fig. 41

3) Push Menu to exit OSD menu.""

3. Click (Write EDID) icon from the tool bar to write DDC data. Then wait for 20-30 seconds ,DDC data will be finished Writing.

Step 6: Save DDC data

Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below:

1. Click (Save) icon (or click "file"-> "save as") from the tool bar and give a file name as shown in Fig. 42.

The file type is EDID46 file (*.ddc) which can be open in WordPad. By

using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table ar completely correct, it can be saved as *.ddc flie to re-load it into DDC IC for DDC Data application.

BZ1A0525000001

BOM Code:

PANEL SUPPLIER CODE

CPT

LPL(LG)

QDI

Serial number (6 digits) Production year/week code Service version change code

BOM (bill of Material) code Sit code (Production center) according TY CODE ( TY---CHUNGLI, HD-HUNGARY,BZ--SUZHOU, DS--DONG GUAN)

26MF605W/17

Failure Mode Of Panel

Go to cover page

Quick reference for failure mode of LCD panel

this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical instruction on this manual to eliminate failure by replace LCD panel.

Polarizer has bubbles

Failure description

Vertical block defect

Vertical dim lines

Vertical lines defect (Always bright or dark)

Horizontal block defect

Phenomenon

Polarizer has bubbles

Foreign material inside polarizer. It shows liner or dot shape.

Concentric circle formed

Horizontal dim lines

Horizontal lines defect (Always bright or dark)

Has bright or dark pixel

Bottom back light of LCD is brighter than normal

Back light un-uniformity

Backlight has foreign material. Black or white color, liner or circular type

SafetyTest Requirements

26MF605W/17

Go to cover page

All units that are returnedfor service or repair mustpass the

originalmanufacturessafety tests. Safety testingrequiresboth

and testing.Hipot Ground Continuity

HI-POT TEST INSTRUCTION

1.Application requirements

1.1 All mains operated products mustpass the Hi-Pot testas describedinthis instruction.

1.2 This test must be performed again after thecovershave been refittedfollowingthe repair, inspection or modification of theproduct.

Test method

1 Connectingconditions

2.1.1 Thetest specified must be appliedbetween the parallel-

bladeplugof the mainscord and all accessible metal parts of theproduct.

2.1.2 Before carryingoutthetest, reliablecondu

connections must beensured and thereafter be maintained throughoutthetest period.

2.1.3 The mains switch(es) must be in the "ON" position.

2.2 Test Requirements

All productsshould be HiPot and Gro follows:

und Continuity tested as

ctive

3. Equipments and Connection

3.1. Equipments For example :

-ChenHwa9032 PROGRAMMABLE AUTO SAFETY

TESTER

-ChenHwa 510BDigital Grounding ContinuityTester

-ChenHwa 901 (AC Hi-pot test), 902 (AC, DC Hi-pot test)

Withstanding Tester

3.2.Connection

*Turn on thepower switch ofmonitor before Hipot and

Ground Continuity testing.

Clip

Condition HiPot Test for HiPot Test for Ground Continuity

voltage (2000VAC) (1200VAC) 25A,AC

Testtime 3seconds 1 second 3 seconds(min.) (min.) Resistance

Trip set at 100 uA 5 mA <=0.09+Rohm, current for Max. R is t (Tester) limitation; set resistance of

Ramp set at 2 time seconds (Tester)

2.2.1 The minimum test durationfor QualityControlInspector

2.2.2 Thetestvoltage must be maintainedwithin the specified

productswhere productswhere Testrequirement the mains inputthe mains input is range is Full 110V AC(USA range(or 220V type)

AC)

Test2820VDC 1700VDC Testcurrent:

Testtime:

required:

at 0.1 uA for the mains cord. Min. Limitation

must be1minute.

voltage + 5%.

(ChenHwa 9032 tester)

Video cable

Connect the "video cable" or "grounding screw" to the CLIP on your tester.

Grounding screw

Connect the power cord to the monitor.

2.2.3 There must be no breakdown duringthetest.

2.2.4 Thegro conductedwith accessible metal parts.

unding bladeorpin ofmains plug must be

Power outlet

4. Recording

Hipot and Ground Continuity testing records have to be kept for a period of 10 years.

(Rear view of monitor)

26MF605W/17

ISP Instructions

Go to cover page

Configuration and procedure

"Easywriter " The software is providedbyNovatek to upgradethe firmware of CPU. It is a windows-based program, which cannot be run in MS-DOS. DDC2BI_ISP TOOL (3138 106 10396) is for the interface between "Parallel Port of PC" and "15 pin-D-SUB connector of Monitor".

System and equipment requirements

1. An i486 (or above) personal computer or compatible.

2. Microsoft operation system Windows 95/98/2000/XP.

3. ISP Software " Easywriter "

4. as showninFig. 1

DDC2BI_ISP TOOL (3138 106 10396)

D-SUB to monitor

Step 3 :Copy the FL1_NAFTA_26_V120_3A10.hex to C:\26MF605W-17

as shown in Fig. 4 .

Lenovo CK5S5

ParallelPorttoPrintPortinPC

Fig. 1

5. Connect and Mains cord to Monitor as shown in Fig. 2.

Connect to Mains cord

6. Install and setup the Easywriter program

DDC2BI_ISP TOOL

Monitor (A)

Video cable

Fig.2

To v i deo car

26MF605W-17 -Monitor (B)

D-Sub

Connect to Mains

cord at this moment.

ISP box

To printer port (LTP1)

------------------------------->

Fig.4

Update the firmware

1.Doubleclick the Easywriter.exeiconindesktop then appears window as showninFig.6 .

Fig. 5

Step1:Makeafolder in your PC as showninFig. 3.

Step 2 : Copy ISP Software Easywriter into your folder

For example : C:\

as s

howninFig.3.

170S5

26MF605W-17

Fig. 3

Fig. 6

+ 78 hidden pages