Philips 220E1SB/75, 220E1SB/05, 220E1SB/78, 220E1SB/93, 220E1SB/94 Service Manual

21.5" LCD Color Monitor Chassis: Meridian 1

Service

Service

Service

Description

Page Description Page

SAFETY NOTICE

ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE

CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN

SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.

CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING

Table of Contents............................................………….1

Revision List................................................…………….2

Important Safety Notice………….................................3

1. Monitor Specifications….............................................4

2. LCD Monitor Description….........................................5

3. Operation instructions….............................................6

3.1General Instructions……………………………….…...6

3.2 Control buttons…………..……………………….……6

3.3 OSD Menu…………………....................................8

4. Input/Output Specification.........................………….10

4.1 Input Signal Connector...........................…………..10

4.2 Factory Preset Display Modes................................11

4.3 Pixel Defect Policy……………………………………12

4.4 Failure Mode of Panel …………………………….…15

5. Block Diagram……………………………................16

5.1 Software Flow Chart............................………….....16

5.2 Electrical Block Diagram.....................……….........18

6. Schematic Diagram…...............................................20

6.1 Main Board………………………………………………20

6.2 Power Board……………………..…………………24

6.3 Key Board…….………………………..…………………26

7. PCB Layout………………………………………………...27

7.1 Main Board………………………………………………..27

7.2 Power Board……………………………………………30

7.3 Key Board………...………………………………………32

8. Wiring Diagram……………………………………….…..33

9. Scalar Board Overview………………………………....34

10. Mechanical Instructions………………………………....35

11. Repair Flow Chart…….…….……………………………39

12. ISP Instructions...….....................................................45

13. DDC Instructions…......................................................48

14. White Balance, Luminance Adjustment……............57

15. Monitor Exploded View….............................................59

16. Recommended & Spare Parts List...……...................60

17. Different Parts List………………………………………76

18. General Product Specification………………….……….82

312278518380

GB

REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES

Copyright 2008 Philips Consumer Lifestyle Subject to modification ○K Jan. 12, 2009

220E1SB/00
220E1SB/05
220E1SB/27
220E1SB/62
220E1SB/69
220E1SB/75
220E1SB/78
220E1SB/93

220E1SB/94
220E1SB/96
220E1SB/97
220E1SB1/01
220E1SB1/62

220E1SB1/94

220E1SB1/97

Meridian 1

2

Revision List

Version Release Date Revision History

A00 Jan.12,2009 Initial release, Draft Version

A01 Jan.22,2009

Add CTV Model 220E1SB/93,220E1SB/94,220E1SB/75, 220E1SB/96,
220E1SB/27

A02 Mar.25,2009 Update BOM for 220E1SB/27

A03 Apr.23,2009

Add 12NC for CTV Model 220E1SB/69,220E1SB/75,220E1SB/93, 220E1SB/94,
220E1SB/97

A04 May.13,2009 Add CTV Model 220E1SB/78

A05 Sep.02,2009

Add AUO V50B/C panel for 220E1SB/00 and 220E1SB/93

Add SEC panel for 220E1SB/00

Change bezel from 21.6″ to 21.5″

Change power board from PWPC8B41MQCW to PWPC9B41AQYO for AUO
V50B/C and SEC panel

A06 Feb.27,2010

Update BOM for 220E1

Add AUO V000/A panel for 220E1SB/00 and 220E1SB/93

Add AUO V00G/H/J panel for 220E1SB/00, 220E1SB/62, 220E1SB/69 and
220E1SB/97

A07 Mar.22,2010

Add AUO V00G/H/J panel for 220E1SB/93

A08 Jul.07.2010

Add CTV Models 220E1SB1/01, 220E1SB1/62, 220E1SB1/94 and 220E1SB1/97

A09 Aug.16,2010

Update BOM for 220E1SB/00 and 220E1SB/93

A10 Sep.26,2010 Add AUO V000/A panel for 220E1SB/62

3

Meridian 1

Important Safety Notice

Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service

procedures recommended by Philips and described in this service manual are effective methods of performing

service operations. Some of these service operations require the use of tools specially designed for the purpose.

The special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read

in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. Philips could not possibly know, evaluate and advise the service trade of all conceivable ways
in which service might be done or of the possible hazardous consequences of each way. Consequently, Philips has
not undertaken any such broad evaluation. Accordingly, a customer who uses a service procedure or tool which is
not recommended by Philips must first satisfy himself thoroughly that neither his safety nor the safe operation of
the equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, Philips Company will be referred to as Philips.

WARNING

Use of substitute replacement parts, which do not have the same, specified safety characteristics, may create
shock, fire, or other hazards.

Under no circumstances should the original design be modified or altered without written permission from Philips.
Philips assumes no liability, express or implied, arising out of any unauthorized modification of design.

Customer assumes all liability.

FOR PRODUCTS CONTAINING LASER:
DANGER- There is invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.

TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION
OF THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit

-Must mount the module using mounting holes arranged in four corners.

-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.

-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.

-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).

-Make certain that treatment person’s body is grounded through wristband.

-Do not leave the module in high temperature and in areas of high humidity for a long time.

-Avoid contact with water as it may a short circuit within the module.

-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth

may damage the panel.)

Meridian 1

4

1. Monitor Specifications

1.1 Technical specifications

LCD Panel

• Type

TFT LCD

• Screen size 21.5″ Visual

• Pixel pitch 0.248 x 0.248mm

• LCD Panel type

1920 x 1080 pixels

R.G.B vertical stripe

Anti-glare polarizer, hard coated

• Effective viewing area 476.64 x 268.11 mm

Display Colors 16.7M

Scanning

• Vertical refresh rate 56 Hz – 76 Hz

• Horizontal Frequency 30 kHz - 83 kHz

Video

• Video dot rate 170 MHz

• Input impedance

- Video 75 OHM

- Sync 2.2K OHM

• Input signal levels 0.7Vpp

• Sync input signal

Separate Sync

Composite Sync

Sync On Green

• Sync polarities Positive and Negative

* T his data is subject to change without notice.

5

Meridian 1

1.2 Physical specifications

• TILT - 5°~ 20°

• POWER SUPPLY 100~ 240 VAC, 50/60Hz

• POWER CONSUMPTION < 40W * (TYP.)

• TEMPERATURE

0℃ to 40℃ (OPERATING)

-20℃ to 60℃ (STORAGE)

• RELATIVE HUMIDITY 20% to 80%

• SYSTEM MTBF 50K HOURS (CCFL 50K HOURS)

• CABINET COLOR 220E1SB: BLACK

2. LCD Monitor Description

The LCD monitor will contain a main board, a power board and a key board which house the flat panel control logic,

brightness control logic and DDC.

The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips

each voltage.

Monitor Block Diagram

AC-IN

100V-240V

Power board

(Include: Adapter, Inverter)

Flat Panel and

CCFL backlight

Main Board

DVI

D-SUB

CCFL Drive.

Video signal, DDC

Key Board

HOST Computer

Meridian 1

6

3. Operating Instructions

3.1 General Instructions

Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the

monitor (see figure). By changing these setting, the picture can be adjusted to your personal preference.

﹡ The power cord should be connected.

﹡ Press the power button to turn on the monitor. The power indicator will light up.

3.2 Control Buttons

Front View

1

To switch monitor’s power on and off

2

MENU/OK

To access OSD menu/Confirm

3

/

To adjust brightness of the display

4

INPUT/

To change the signal input source

5

/

Auto picture control switching in wide and 4:3 format.

Return to previous OSD level.

6

AUTO

Automatically adjust the horizontal position, vertical

position, and phase and clock settings.

7

Meridian 1

Rear View

1 Kensington anti-thief lock

2 AC power input

3

DVI-D(available for selective models）

4 VGA input

Meridian 1

8

3.3 OSD Menu

Description of the On Screen Display

This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors

directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use

when operating the monitor.

Basic and simple instruction on the control keys

When you press the MENU/OK button on the front control of your monitor, the On-Screen-Display (OSD) main
controls window will pop up and you can then start making adjustments to your monitor’s various features. Use the

▲▼ keys to make your adjustments.

Dual Model (only for 220E1SB/69)

Analog Model

9

Meridian 1

The OSD tree

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want

to work your way around the different adjustments later on.

Meridian 1

10

4. Input/ Output Specification

4.1 Input Signal Connector

Analog connectors

Pin No. Description Pin No. Description

1 Red video input 9 DDC +5V

2 Green video input (SOG) 10 Logic ground

3 Blue video input 11 Ground

4 Sense (GND) 12 Serial data line (SDA)

5 Cable detect (GND) 13 H.Sync/ H +V.Sync

6 Red video ground 14 V.Sync

7 Green video ground 15 Data clock line (SCL)

8 Blue video ground

Digital Connectors

Pin No. Signal Name Pin No. Signal Name

1 TMDS Data 2- 13 TMDS Data 3+

2 TMDS Data 2+ 14 +5V Power

3 TMDS Data 2/4 Shield 15 Ground(for+5V)

4 TMDS Data 4- 16 Hot Plug Detect

5 TMDS Data 4+ 17 TMDS Data 0-

6 DDC Clock 18 TMDS Data 0+

7 DDC Data 19 TMDS Data 0/5 Shield

8 N.C. 20 TMDS Data 5-

9 TMDS Data 1- 21 TMDS Data 5+

10 TMDS Data 1+ 22 TMDS Clock Shield

11 TMDS Data 1/3 Shield 23 TMDS Clock +

12 TMDS Data 3- 24 TMDS Clock -

11

Meridian 1

4.2 Factory Preset Modes

H. freq (KHz) Resolution V. freq (Hz)

31.47 640 x 480 59.94

37.50 640 x 480 75.00

37.88 800 x 600 60.32

46.88 800 x 600 75.00

48.36 1024 x 768 60.00

60.02 1024 x 768 75.03

67.50 1152 x 864 75.00

60.00 1280 x 960 60.00

63.89 1280 x 1024 60.02

79.98 1280 x 1024 75.03

55.94 1440 x 900 59.89

75.00 1600 x 1200 60.00

65.29 1680 x 1050 59.95

67.50 1920 x 1080 60.00

Meridian 1

12

4.3 Pixel Defect Policy

Philips strives to deliver the highest quality products. We use some of the industry’s most advanced manufacturing

process and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in

flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that panels will be free from pixel

defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or

replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect

levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a

TFT LCD panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a

21.5″ FHD monitor may be defective. Furthermore, Philips sets even higher quality standard for certain types or

combinations of pixel defects that are more noticeable than others. This policy is valid worldwide.

Pixels and Sub pixels

A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many

pixels together form an image. When all sub pixels of pixel are lit, the three colored sub pixels together appear as a

single white pixel. When all are dark, the three colored sub pixels together appear as a signal black pixel. Other

combinations of lit and dark sub appear as single pixels of other colors.

Types of Pixel Defects

Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and

several types of sub pixel defects within each category.

Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or ‘on’. That is, a Bright dot is

a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are three types of bright

dot defects:

R G B

R G B

subpixel

subpixel

subpixel

pixel

G

R

B

P

Y

C

W

13

Meridian 1

Two adjacent lit sub pixels:

- Red + Blue = Purple Three adjacent lit sub pixels

(one white pixel) One lit red, green or blue sub pixel - Red + Green = Yellow

- Green + Blue = Cyan (Light Blue)

A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green

bright dot is 30 percent brighter than neighboring dots.

Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or ‘off’. That is, a dark dot

is a sub-pixel that stands out on the screen when the monitor displays a light pattern. There are two types of black

dot defects:

One dark sub pixel Two or three adjacent dark sub pixels

Proximity of Pixel Defects

Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable,

Philips also specifies tolerances for the proximity of pixel defects.

Pixel Defect Tolerances

In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a

Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following

tables.

BRIGHT DOT DEFECTS ACCEPTABLE LEVEL

MODEL

220E1

1 lit subpixel 3

2 adjacent lit subpixels 1

3 adjacent lit subpixels (one white pixel) 0

Distance between two bright dot defects * >15mm

Total bright dot defects of all types 3

Meridian 1

14

BLACK DOT DEFECTS ACCEPTABLE LEVEL

MODEL

220E1

1 dark subpixel 5

2 adjacent dark subpixels 2

3 adjacent dark subpixels 0

Distance between two black dot defects * >15mm

Total black dot defects of all types 5

TOTAL DOT DEFECTS ACCEPTABLE LEVEL

MODEL

220E1

Total bright or black dot defects of all types 5

Note:

* 1 or 2 adjacent sub pixel defects = 1 dot defect

15

Meridian 1

4.4 Failure Mode Of Panel



Failure description

Phenomenon

Vertical block defect

Vertical dim lines

Vertical lines defect
(Always bri

g

ht or dark)

Horizontal block defect

Horizontal dim lines

Horizontal lines defect
(Always bri

g

ht or dark)

Has bri

g

ht or dark pixel

Polarizer has bubbles

Polarizer has bubbles

Foreign material inside
polarizer. It shows liner or
dot shape.

Concentric circle formed

Bottom back light of LCD is
brighter than normal

Back light un-uniformity

Backli

g

ht has foreign material.
Black or white color, liner or
circular type

Quick reference for failure mode of LCD panel

this pa

g

e presents problems that could be made by LCD panel.
It is not necessary to repair circuit board. Simply follow the mechanical
instruction on this manual to eliminate failure by replace LC D panel.

Meridian 1

16

5. Block Diagram

5.1 Software Flow Chat

1

2

N

Y

5

Y

N

10

Y

N

12

Y

N

7

Y

N

6

4

3

9

14

11

13

Y

N

15

Y

N

16

17

19

Y

N

18

17

Meridian 1

1) MCU initializes.

2) Is the EPROM blank?

3) Program the EPROM by default values.

4) Get the PWM value of brightness from EPROM.

5) Is the power key pressed?

6) Clear all global flags.

7) Are the AUTO and SELECT keys pressed?

8) Enter factory mode.

9) Save the power key status into EPROM.

Turn on the LED and set it to green color.

Scalar initializes

10) In standby mode?

11) Update the lifetime of back light.

12) Check the analog port, are there any signals coming?

13) Does the scalar send out an interrupt request?

14) Wake up the scalar.

15) Are there any signals coming from analog port?

16) Display "No connection Check Signal Cable" message. And go into standby mode after the message

disappears.

17) Program the scalar to be able to show the coming mode.

18) Process the OSD display.

19) Read the keyboard. Is the power key pressed?

Meridian 1

18

5.2 Electrical Block Diagram

5.2.1 Main Board

Flash Memory

PM25LV010A

(U402)

Panel Interface

(CN301)

Crystal 12MHz

(X401)

Keypad Interface

(CN402)

Scalar IC NT68667UFG/C

(Include MCU, ADC, OSD)

(U401)

D-Sub Connector

(CN101)

ESD

AZC099-04S

(U103)

H sync

V sync
RGB

ESD

AZC099-04S

(U104)

VGA_R+
VGA_G+
VGA_B+

H_Sync
V_Sync
DSUB_SCL
DSUB_SDA

EEPROM M24C16

(U403)

DVI Connector

(CN102)

ESD

AZC099-04S

(U105)

ESD

AZC099-04S

(U106)

DAT0+/­RXCP
RXCN

DAT2+/­RX1N
RX1P

DVI_SCL

DVI_SDA

ESD

AZC199-04S

(U107)

HPD

DVI_HPD

19

Meridian 1

5.2.2 Power/Inverter Board

DIM

EMI filter

Start Circuit: R908

PWM Control IC

Transformer

AC input

16V

ON/OFF

Control

PWM Control IC

Feedback Circuit

Output Circuit

Transformer

MOSFET

Lamp

ON/OFF

5V

Bridge
Rectifier
and Filter

Feedback Circuit

Rectifier

CN902

Over Voltage

20

Meridian 1

6. Schematic

6.1 Main Board

715G3108-1

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

DVI_HPD

VGA_B+

VGA_R+

VGA_G+

VGA_R+

DSUB_5V

VGA_PLUG

VGA_G+

VGA_G+

VGA_B+

VGA_R+

DVI_SDA DDC2_SDA

DDC2_SCLDVI_SCL

DSUB_SDA

VGA_G-

VGA_B-

VGA_R-

DVI_SCL
DVI_SDA

VGA_B+

VGA_R-

V_Sync

VGA_G-

V_Sync

H_Sync

VGA_B-

DSUB_SDA H_Sync

DSUB_SCL

DSUB_SCL

5VCC

DSUB_5V

ESD_5VESD_5V

DVI_5V

ESD_5V

DGNDGND POWER

ESD_5V

5V_ESD

5V_ESD

5V_ESD 5VCC

E5VCC

RX1P

DSUB_R-

DSUB_R+

DSUB_G-

DSUB_SOG

RX0N

RX2N

DSUB_G+

RX2P

DSUB_B+

DSUB_B-

RXCN

RX1N

RXCP

DSUB_H

DDC1_SCL

DDC1_SDA

DSUB_V

RX0P

DDC2_SCL
DDC2_SDA

HDCP_CTRL

DDC_WP

VGA_DET

DVI_DET

U101

ǂ

U105

ǂ

U106

ǂ

U103

ǂ

CN101 A2 CN102 B1 C101 B3 C102 A5 C103 A2 C104 A2 C105 A4 C106 A5 C107 A5 C108 A5 C109 A4 C110 A5
C111 B5 C112 A3 C113 B4 C114 B5 C115 C2 C117 C5 C118 D2 C119 D3 C120 D1 FB101 B4 FB102 A4 FB103 A4
FB105 C4 R101 A1 R102 A1 R103 A2 R104 A2 R105 A5 R106 A2 R107 A2 R108 A4 R109 A5 R110 A5 R111 A5
R112 A4 R113 B1 R114 A5 R115 B5 R116 B4 R117 B5 R118 B3 R119 B3 R120 B2 R121 C4 R122 C4 R126 C3
R127 C3 R128 C3 R129 C3 R130 C3 R131 C3 R132 C3 R134 C3 R136 C5 R137 C4 R138 C4 R139 B1 R140 B2
R141 B2 R142 C5 R143 A1 R144 A1 U102 C5 U103 B3 U104 A3 U105 D2 U106 D2 U107 D1 ZD104 A2 ZD105 A2

INPUT

C109
5pF/50V

C109
5pF/50V

R114 100R 1/16W 5%R114 100R 1/16W 5%

ZD104

RLZ5.6B

ZD104

RLZ5.6B

DAT2-

1

DAT2+

2

2/4shield

3

DAT4-

4

DAT4+

5

DDC SCL

6

DDC SDA

7

VSYNC

8

DAT1-

9

DAT1+

10

1/3shield

11

DAT3-

12

DAT3+

13

+5V

14

SYNC GND

15

HPD

16

DAT0-

17

DAT0+

18

0/5shield

19

DAT5-

20

DAT5+

21

clk shield

22

clk+

23

clk-

24

GND26GND

25

CN102

JACK

CN102

JACK

I/O1

1

GND

2

I/O23I/O3

4

VDD

5

I/O4

6

U107U107

R115 100R 1/16W 5%R115 100R 1/16W 5%

C112NCC112
NC

C101NCC101
NC

C104

22pF

C104

22pF

R109 100R 1/16W 5%R109 100R 1/16W 5%

R108

75R 1/16W 5%

R108

75R 1/16W 5%

R131 10R 1/16W 5%R131 10R 1/16W 5%

1 2

FB105

120 OHM

FB105

120 OHM

1

6

2

7

3

8

4

9

5

11

12

13

14

15

10

17 16

CN101

DB15

CN101

DB15

ZD105
RLZ5.6B

ZD105
RLZ5.6B

R121 100R 1/16W 5%R121 100R 1/16W 5%

R127 10R 1/16W 5%R127 10R 1/16W 5%

1 2

FB102

BEAD

FB102

BEAD

R102 100R 1/10W 5%R102 100R 1/10W 5%

R110 470R 1/16W 5%R110 470R 1/16W 5%

R113
100R 1/16W 5%

R113
100R 1/16W 5%

R144
4K7 1/16W 5%

R144
4K7 1/16W 5%

C113
5pF/50V

C113
5pF/50V

C106

0.047uF

C106

0.047uF

R129 10R 1/16W 5%R129 10R 1/16W 5%

C119C119

C117

0.1uF/16V

C117

0.1uF/16V

C103

22pF

C103

22pF

R101

100R 1/16W 5%
R101

100R 1/16W 5%

R118 100R 1/16W 5%R118 100R 1/16W 5%

C111

0.047uF

C111

0.047uF

R132 10R 1/16W 5%R132 10R 1/16W 5%

1 2

FB103

BEAD

FB103

BEAD

R112

75R 1/16W 5%

R112

75R 1/16W 5%

R136

4K7 1/16W 5%

R136

4K7 1/16W 5%

R126 10R 1/16W 5%R126 10R 1/16W 5%

R143

4K7 1/16W 5%

R143

4K7 1/16W 5%

R117 100R 1/16W 5%R117 100R 1/16W 5%

R142

1K 1/16W 5%

R142

1K 1/16W 5%

R140
100R 1/16W 5%

R140
100R 1/16W 5%

A0

1

A1

2

A2

3

VSS4SDA

5

SCL

6

WP

7

VCC

8

U102

M24C02-WMN6TP

U102

M24C02-WMN6TP

R103 1K 1/16W 5%R103 1K 1/16W 5%

R139 1K 1/16W 5%R139 1K 1/16W 5%

C115

0.1uF/16V

C115

0.1uF/16V

R105 100R 1/16W 5%R105 100R 1/16W 5%

C118C118

R130 10R 1/16W 5%R130 10R 1/16W 5%

R134 10R 1/16W 5%R134 10R 1/16W 5%

R138
4K7 1/16W 5%

R138
4K7 1/16W 5%

C105
5pF/50V

C105
5pF/50V

C110

0.047uF

C110

0.047uF

I/O1

1

GND

2

I/O23I/O3

4

VDD

5

I/O4

6

U103

AZC099-04S

U103

AZC099-04S

R116

75R 1/16W 5%

R116

75R 1/16W 5%

R111 100R 1/16W 5%R111 100R 1/16W 5%

R119 100R 1/16W 5%R119 100R 1/16W 5%

1 2

FB101

BEAD

FB101

BEAD

I/O1

1

GND

2

I/O23I/O3

4

VDD

5

I/O4

6

U105
AZC099-04S

U105
AZC099-04S

C114

0.047uF

C114

0.047uF

R107

2K2 1/16W 5%

R107

2K2 1/16W 5%

R128 10R 1/16W 5%R128 10R 1/16W 5%

C120C120

R141 1K 1/16W 5%R141 1K 1/16W 5%

C107
1000pF

C107
1000pF

R120
1K 1/16W 5%

R120
1K 1/16W 5%

R106

2K2 1/16W 5%

R106

2K2 1/16W 5%

C102

0.047uF

C102

0.047uF

R122 100R 1/16W 5%R122 100R 1/16W 5%

C108

0.047uF

C108

0.047uF

I/O1

1

GND

2

I/O23I/O3

4

VDD

5

I/O4

6

U106
AZC099-04S

U106
AZC099-04S

I/O1

1

GND

2

I/O23I/O3

4

VDD

5

I/O4

6

U104

AZC099-04S

U104

AZC099-04S

R104 1K 1/16W 5%R104 1K 1/16W 5%

R137

4K7 1/16W 5%

R137

4K7 1/16W 5%

21

Meridian 1

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

AO3401L

21

S

D

3

G

CN301 A5
C301 C4
C302 B3
C303 C3
C304 C2
C305 C3
C306 C2
Q301 B3
Q302 C2
R301 C4
R303 B2
R304 B2
R305 C3
R306 C1
R307 C1

OUTPUT

PPWR_ON#

TCLK2M

T4M

T4P

T2P

T3P

TCLK2P

T5P

TCLK1M

T7M

T7P

T0P

T5M

T6P

T6M

T2M

TCLK1P

T3M

T0M

T1M

T1P

PANEL_VCC

PANEL_VCC

+5V

+

C305

100uF25V

R304

47K 1/16W 5%

C303

NC

R307

47K 1/16W 5%

C304

NC

R303

10K 1/16W 5%

C301

0.1uF/16V

C306

0.1uF 16V

R306

10K 1/16W 5%

C302

0.1uF/16V

Q301
AO3401

R301

330 OHM 1/4W

CN301

CONN

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

Q302

2N3904S-RTK/PS

R305

0R05 1/8W

22

Meridian 1

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

lock type

CN701 A1
C701 B2
C702 C1
C703 A2
C704 B5
C705 B5
C706 C4
C707 C5
C708 C4
C709 C4
C710 A2
C711 B4
D701 A2
D702 B3
FB701 B3
Q701 C1
R701 A3
R702 C1
R703 A2
R704 C1
R705 C2
R706 C2
R707 A2
R710 A2
U701 C4
U702 B4
U703 C4

POWER

BKLT-VBRI

BKLT-EN

+5V

+5V

BKLT-VBRI
BKLT-EN

PANEL_ID#

Mute

Volume#

on_BACKLIGHT

adj_BACKLIGHT

VCC1.8

VCC3.3

VCC3.3

VCC3.35VCC

5VCC

5VCC

5VCC

+5V

DSUB_5VDVI_5V

E5VCC

C703
NC

+

C706

100uF25V

R702

10K 1/16W 5%

C709

0.1uF/16V

+

C707

100uF25V

R703 NC/4K7 1/16W 5%

R701
NC

C701
NC

R706

1K 1/16W 5%

U702

AZ1117D-1.8-E1

2 3

1

OUT IN

GND

R707 NC/4K7 1/16W 5%

C708

0.1uF/16V

C711

0.1uF/16V

Q701
2N3904S-RTK/PS

D701

SM340A

C702

NC

U701

NC/AP1117E33LA

1

23

VSS

VOUTVIN

+

C704

100uF25V

FB701
300 OHM

1 2

D702

BAT54C

1

3

2

CN701

CONN

1
2
3
4
5
6
7
8
9

C705

0.1uF/16V

C710
NC

R704

4K7 1/16W 5%

R710 NC

R705

10K 1/16W 5%

U703

AP1117D33LA

123

ADJ(GND)

VOUT

VIN

23

Meridian 1

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

FFC CONNECTOR

DUBUG

SCALER

CN401 D2
CN402 D5
CN403 D5
CN405 C1
CN406 D2
C401 A4
C403 A1
C404 A1
C406 A2
C407 A2
C410 A1
C411 A5
C412 A1
C413 A2
C420 C2
C421 C2
C422 C1
C423 A2
C430 A1
C431 D3
C432 D3
C433 D3
C434 D4
C435 D4
C436 D5
C438 A2
C439 A1
C440 A1
C442 A2
C446 C1
C447 A1
C448 A2
FB401 A1
FB403 A2
FB404 A1
FB406 A1
FB407 A1
Q401 B5
Q402 C5
R401 A2
R402 C3
R403 B1
R405 C1
R406 C3
R407 B1
R408 D4
R409 A4
R411 D4
R412 C2
R414 A4
R415 B2
R416 B2
R417 C3
R418 C3
R419 C3
R420 C3
R421 C3
R422 C3
R425 C3
R429 C2
R431 C2
R436 D1
R437 D1
R438 D1
R439 D1
R440 A4
R441 A4
R443 D3
R444 D3
R445 D1
R446 D1
R454 C2
R462 C2
R465 B4
R466 B5
R467 B4
R468 B5
R469 B4
R470 B5
R471 C4
R472 C5
U401 A2
U402 A5
U403 B5
X401 C2
ZD401 D3
ZD402 D4
ZD403 D3

POWER_KEY#

KEY2

LED_LF_BLUE

KEY1

SPI_CE
SPI_SO
SPI_SI
SPI_CK
WP

MSCL

MSDA

TX

KEY1

POWER_KEY#

5V_DET

5V_DET

SPI_CK
SPI_SI

SPI_CE
SPI_SO

TX

HSO

VSO

VSO
HSO

EE_WP

KEY2

LED_ORANGE

KEY_LEFT

LED_GRN/BLUE

KEY1

KEY_RIGHT
KEY_AUTO

WP

KEY2

POWER_KEY#

LED_LF_BLUE

EE_WP

LED_LF_BLUE

LED_ORANGE

LED_GRN/BLUE

LED_A

LED_ORANGE

LED_B

LED_GRN/BLUE

LED_B

MSCL

LED_A

MSDA

DDC2_SCL

DDC2_SDA

DDC1_SDA
DDC1_SCL

RX0N

RX1P

RX2P

RX0P

RX1N

RXCP

RX2N

RXCN

DSUB_H
DSUB_V

T5P

T1M

TCLK1P

T4M
T4P
T5M

T2M
T2P

T6P

T0P

T6M

T3M

TCLK2P

TCLK2M

T0M

T1P

T7M
T7P

TCLK1M

T3P

adj_BACKLIGHT

on_BACKLIGHT

Volume#

HDCP_CTRL

PPWR_ON#

DVI_DET

VGA_DET

PANEL_ID#

DDC_WP

MUTE

DSUB_R-

DSUB_B+
DSUB_B-

DSUB_R+

DSUB_G-

DSUB_G+

DSUB_SOG

VCC3.3

+5V

ADC_VAA

CVDD

VCC3.3

AVCC

AVCC

PVCC

DVDD

CVDD

PVCC

DVDD

ADC_VAA

VCC1.8

AVCC

+5V

DVDD

DVDD

DVDD

+5V

+5V

R422 NC/120R 1/8W

C432

0.1uF/16V

R402 100R 1/16W 5%

Q402
NC/2N3906S-RTK/PS

1

23

R420
120R 1/8W 5%

U402

PM25LV010A

1
2
3
4 5

6

7

8

CE
SO
WP#
GND SI

SCK

HOLD#

VCC

R418 120R 1/16W 5%

C401

0.22uF16V

R440

4K7 1/16W 5%

U403

M24C16

1
2
3456

7

8

NC
NC
NC

VSSSDA

SCL

WC

VCC

ZD401

RLZ5.6B

R408
10K 1/16W 5%

R429 100R 1/16W 5%

R419 120R 1/8W 5%

FB403
300OHM

R439 NC

R443

3.9K OHM 1% 1/16W

C438
1uF/16V

C410

0.1uF/16V

C423

0.1uF/16V

C404

0.1uF/16V

R409 100R 1/16W 5%

FB401
300OHM

R441
4K7 1/16W 5%

R446 0R05 1/16W

R472
0R05 1/16W

C411

0.22uF16V

C439

1uF 16V

C442

0.1uF/16V

FB404
300OHM

R444

3.9K OHM 1% 1/16W

R425 1K 1/16W 5%

CN402CONN

1
2
3
4
5
6
7

R401
470 OHM +-1% 1/16W

CN406
NC/CONN

1
2
3
4
5

C435

0.1uF/16V

C420 22pF

R436 0R05 1/16W

R469

NC/2K2 1/16W 5%

R415 1K 1/16W 5%

C433

0.1uF/16V

C430

0.1uF/16V

C446 0.1uF/16V

R465

NC/10K 1/16W

R414
10K 1/16W 5%

C421 22pF

R454 NC/10K 1/16W 5%

C440

1uF 16V

CN403
NC/CONN

1
2
3

C436

0.1uF/16V

R471
0R05 1/16W

R431 100R 1/16W 5%

R462
1M 1/16W 5%

R406 NC/120R 1/8W

CN405

NC/CONN

1
2
3
4

C431

0.1uF/16V

U401

NT68667UFG/C

1

2

3

4
5

6

7
8

9

10
11

12

13
14

151617

18

19
20

21
22
23

24
25

26

27

28

29

30

31
32

33

34
35

36

37

38

39

40

41
42

434445

46
47

48

49
50

515253

54

55

56

57

58

59

60

61

62

63

64

102

101

100
99
98
97
96
95
94
93
92
91

90

89

88
87
86
85
84
83
82
81
80
79

78

77
76
75
74
73
72
71
70
69
68

67
66
65

128

127

126

125

124
123
122

121
120

119

118

117

116

115

114

113

112

111

110

109

108

107

106

105

104

103

RSTB

DVDD

DGND

RX2+
RX2-

AVCC

RX1+
RX1-

AGND

RX0+
RX0-

AGND

RXC+
RXC-

AVCC

REXT

PVCC

PGND

BIN1+
BIN1-

SOG1I
GIN1+
GIN1-

RIN1+
RIN1-

ADC_VAA

ADC_GNDA

PC2

PD6

PB3/ADC3/INTE1

P31/TXD
P30/RXD

PB2/ADC2/INTE0

PB7/DDC_SDA1*
PB6/DDC_SCL1*

PA3/PWM5

PA4/PWM6*

PA5/PWM7*

PA6/PWM8*

PA7/PWM9*

HSYNCI1
VSYNCI1

PLL_GND

GND

PLL_VDD

PB5/DVI_SDA0*
PB4/DVI_SCL0*

PD5

P35
P34

DVDD

CVDD

DVDD

RSBA1P/V0

RSBA1M/V1

RSBA2P/V2

RSBA2M/V3

RSBA3P/V4

RSBA3M/V5

RSCLKAP/V6

RSCLKAM/V7

RSGA1P/VCKI

DGND/CGND

DGND/CGND

PC6

DGND/CGND

DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND

DVDD

DGND/CGND

RSGB1M/T0M

RSGB1P/T0P

RSCLKBM/T1M

RSCLKBP/T1P
RSBB3M/T2M

RSBB3P/T2P

RSBB2M/TCLK1M

RSBB2P/TCLK1P

RSBB1M/T3M

RSBB1P/T3P

DGND/CGND

RSRA3M/T4M/RSRB0M

RSRA3P/T4P/RSRB0P

RSRA2M/T5M/GSGB0M

RSRA2P/T5P/RSGB0P

RSRA1M/T6M/RSGB0M

RSRA1P/T6P/RSBB0P

RSGA3M/TCLK2M

RSGA3P/TCLK2P

RSGA2M/T7M

RSGA2P/T7P

PA1/PWM3
PA2/PWM4
PA0/PWM2

OSCO

OSCI

PB0/ADC0

PB1/ADC1

PC5
PC4/PWM1
PC3/PWM0

PC1*
PC0*

CVDD

PWMB*/GPO8

PWMA*/GPO7

NC

CVDD

INT_HSO/GPO5

INT_VSO/GPO4

GPO3/AD1

GPO2/AD0

NC

GND

PD4

SPI_CLK

SPI_SI

SPI_SO

SPI_CE

PC7

R445 0R05 1/16W

C412

0.1uF/16V

R416 1K 1/16W 5%

ZD402

RLZ5.6B

CN401

NC/2x4PIN/1.0mm

1
2
3
4
5
6
7
8

R470

NC

R438 NC

R405 10K 1/16W 5%

C422

0.1uF/16V

R412 100R 1/16W 5%

C413

0.1uF/16V

FB406
300OHM

C407

0.1uF/16V

R407

20K OHM 1/16W

R466
NC/120R 1/8W

C403

0.1uF/16V

C447

0.1uF/16V

Q401
NC/2N3906S-RTK/PS

R411

10K 1/16W 5%

R403

10K 1/16W 5%

R421 NC/120R 1/8W

R437 NC

C406

0.1uF/16V

ZD403

RLZ5.6B

R467
NC/0R05 1/16W

R417 100R 1/16W 5%

X401

12MHz

1 2

C448

0.1uF/16V

FB407
300OHM

C434

0.1uF/16V

R468 NC/0R05 1/16W

24

Meridian 1

6.2 Power Board

715G2892-1A-4

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

!

!

!

!

!

!

!

!

!

!

!

!

!

!

BD901 A1 CN901 C1 CN902 C3 C900 C3 C902 C1 C903 C1 C907 A1 C908 B1 C909 A1 C911 A2
C912 B2 C913 B2 C914 B2 C915 C1 C916 A4 C917 A4 C918 A4 C920 B4 C921 D4 C922 B4
C923 A4 C924 C3 C925 B4 C926 D3 C927 B1 C931 D4 D901 A3 D903 A2 D904 B2 D905 B3
D906 B3 D907 B2 D908 B1 FB901 B2 FB902 D2 F901 C1 F902 A5 F903 C5 GND1 D2 HS1 C1
HS2 D2 IC901 B2 IC902 B3 IC903 C3 L901 B1 L905 A4 L906 A4 L907 C4 NR901 B1 Q901 B2
Q904 A4 R900 B1 R901 B1 R902 B1 R903 A3 R904 A4 R905 A5 R906 A2 R907 A5 R908 A2
R909 A3 R910 A3 R912 B3 R913 B2 R914 B5 R916 C5 R917 B2 R918 B2 R919 B3 R920 B3
R921 B1 R923 B2 R924 C2 R925 C5 R928 C3 R929 A3 R930 A3 R931 A1 R932 A1 R933 B1

POWER

+16V

+5V1

+5V

ON/OFF

DIM

VOL

MUTE

+5V+5Vi

R919
150R 1/8W 5%

D903

FR107

R925

9K1 1/10W 1%

+

C921
NC/1000uF25V

R931
NC

R913

5.1 OHM 1/4W +-5%

IC901

LD7576GS

1
2
3
4 5

6

7

8

RT
COMP
CS
GNDOUT

VCC

NC

HV

Q901

STP10NK70ZFP

C915

0.01uF

GND1
GND

1
2

R929 100 OHM 1/4W

D904
FR103

R904

75OHM +-5% 2WS

L906

Coil

T901

POWER X'FMR

1

3

4

5

6

7

8

9
10

11

12

D906

MBRF1060CT

123

D901

FMX-12SL

123

CN901
SOCKET

12

3

C909
NC/0.22uF/275V

R918

10K 1/10W 1%

R932
NC

R935
NC

L901

30mH

142

3

HS2
HEAT SINK(D901 D906)

1
2

C900
3300pF 250V

R907
1K 1/10W 1%

D905 NC/31DQ06FC3

C926

0.1uF/16V

R928
1K 1/10W 1%

C914
470pF

+

C922
470UF M 16V

R906
100K OMH 2W +-5%

C917

0.001uF

R905
0R05 1/10W 5%

+

C920

680uF 10V

C924

0.1uF/16V

FB902

BEAD

1 2

R914
NC/43.2K OHM 1% 1/4W

D908
NC/IN4148

C908

0.47uF/275V

R933
NC

+

C913
22uF/50V

C923

0.001uF

ZD901
TZX18B

R917
10R 1/4W 5%

+

C925
NC

R910 100 OHM 1/4W

R920
1K 1/10W 1%

R909 100 OHM 1/4W

+

C918

1000uF 25V

-

+

BD901

KBP208G

2

1

3

4

IC902

PC123X2YFZOF

12

43

R934
NC

C927

0.047uF

F902

FUSE

C911

1500PF2KV

C912

0.1uF

L907
Coil (NC)

NR901
NTCR

IC903
KIA431A-AT/P

C903

1000pF

R912 100 OHM 1/4W

R930 100 OHM 1/4W

C902

1000pF

R902

680K OHM 1/4W +-5%

D907
IN4148

R903 100 OHM 1/4W

+

C907
100uF/450V

L905

Coil

R921

(NC)100K OHM 1% 1/8W

R924

0.39 OHM 2W +-5%

F903

FUSE(NC)

R901

680K OHM 1/4W +-5%

F901

FUSE

R900

680K OHM 1/4W +-5%

FB901
BEAD

12

+

C931
NC

CN902

1

2

3

4

5

6

7

8

9

R916

10K 1/10W 1%

HS1
HEAT SINK(Q901)

1
2

R923
220 OHM 1/4W

Q904

KTD1028

C916

0.001uF

R908
10K OHM 1/4W +-5%

25

Meridian 1

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

CN801 A4 CN802 A4
CN803 B4 CN804 B4
C801 A1 C802 A2
C803 A1 C804 A3
C805 B1 C806 B1
C807 B1 C808 B2
C809 B2 C810 B2
C811 A3 C812 B1
C813 B3 C814 B3
C815 A3 C817 B3
C818 B1 C819 A4
C820 A4 C821 B4
C822 B4 D801 B2
D803 B4 D806 B3
D807 B3 D808 C3
IC801 B2 L801 A4
L802 B4 PT801 A3
Q802 B2 Q805 A3
Q806 A3 R801 B1
R802 A1 R803 A1
R804 A2 R806 B1
R807 B1 R808 B1
R809 B2 R810 B2
R811 B2 R812 B1
R813 B2 R815 B1
R816 A2 R817 A2
R818 A2 R819 A2
R820 A1 R821 B2
R828 B3 R830 B3
R836 B3 R837 B3
R838 B3 R839 B3
R840 C3 R841 C3
R842 C3 R843 C3
R844 C3 R845 C3
ZD802 A1 ZD803 A2

INVERTER

ON/OFF

+16V

+5Vi

LV2

LV1

LV3

DIM

LV4

LV3

LV4

LV1

LV2

R818 2R2 1/8W 5%

L802

L

124

3

L801

L

124

3

D801

IN4148

CN802

CONN

1
2

R819 2R2 1/8W 5%

ZD802
RLZ5.6B

1 2

+

C804

1000uF 25V

R843

10K 1/10W 5%

C803

0.1uF

R806

100K 1/10W 5%

R802

22R 1/8W 5%

R821
10 OHM +-5% 1/10W

D808

BAV70

3

1

2

R844

10K 1/10W 5%

R809

1M 1/10W 5%

Q805

AO4620

1

2

3

4 5

6
7
8

S2

G2

S1

G1 D1

D1
D2
D2

C819

68pF3KV

R813
100K 1/10W 5%

C811

0.1uF/50V

C812
NC

C810

0.0022uF

CN801

CONN

1
2

C818

1.5UF/10V

C808

0.033uF

R820
10 OHM +-5% 1/10W

R808

390R 1/10W 1%

C822

68pF3KV

R836

56KOHM +-5% 1/10W

D803
BAV99

3

1

2

R845

10K 1/10W 5%

R841 1M 1/10W 5%

C809
220pF

Q806

AO4620

1

2

3

4 5

6
7
8

S2

G2

S1

G1 D1

D1
D2
D2

R807
10K 1/10W 5%

IC801 ta9687GN-A-0-TR

1

2

3

4

5

6

7

89
10
11
12
13
14
15
16

VSEN

SSTCMP

CT

RT1

GNDA

PDR2

GNDP

NDR2NDR1
PDR1
VDDA
TIMER
PWM
ISEN
OVPT
ENA

R817

2R2 1/8W 5%

R839 1M 1/10W 5%

C821

68pF3KV

R840 1M 1/8W 5%

D806

BAV70

3

1

2

ZD803
RLZ5.6B

1 2

R837
7K5 1/10W 5%

R842

10K 1/10W 5%

Q802

2N7002 SOT-23

R810

75K 1/10W 1%

C805

0.022uF

CN804

CONN

1
2

C802

0.047uF

C817

2PF6KV

C814
220pF

C806

2.2uF/16V

C820

68pF3KV

R830

5K1 1/8W 5%

R801
10K 1/8W 5%

R804

5K1 1/8W 5%

C813
NC

C807

3.3NF

C801

0.047uF

R828

6.2M OHM 1/2W

R816 2R2 1/8W 5%

D807

BAV70

3

1

2

CN803

CONN

1
2

C815

0.1uF/50V

PT801

POWER X'FMR

6

2

7

5

1 8

R815
NC

R838 1M 1/10W 5%

R803

5K1 1/8W 5%

R812

100K 1/8W 5%

R811

82 KOHM +-1% 1/8W

26

Meridian 1

6.3 Key Board

715G2836-1-2

1

1

2

2

3

3

4

4

5

5

A A

B B

C C

D D

SOURCE

LED

CONNECTOR

AUTOUP DOWNMENUPOWER

CN101

CN001 A1
C001 B1
C002 B2
C003 B2
C004 B2
C005 B2
C006 B4
C007 B3
C008 B4
C009 B3
C010 B5
C011 B3
D001 A2
R001 A3
R002 A3
R003 B3
R004 B3
R005 B3
R006 B3
SW001 B5
SW002 B4
SW003 B5
SW004 B4
SW005 B3
SW006 B3
ZD001 B4
ZD002 B3
ZD003 B5
ZD004 B4
ZD005 B3
ZD006 B3

KEYPAD

AUTO

LED_RED#

LED_RED#

LED_GRN#

LED_GRN#

LBADC1
LBADC2
DC_POWERON

SOURCE

VOL+

POWER

MENU

VOL-

GND

SGND SGNDSGND SGND

SGND

SGND SGND SGND SGNDSGND

SGND

SGNDSGND

ZD004NC/UDZSNP5.6B

C006NC/0.1uF

R005 2K4 1/8W

CN001

CONN

1
2
3
4
5
6

C007NC/0.1uF

C005

NC/0.001uF

R003 910R 1/8W

C010NC/0.1uF

C011NC/0.1uF

C001

NC/0.001uF

D001

LED

1

3

2

C009NC/0.1uF

ZD006NC/UDZSNP5.6B

SW001

SW

21

3 4

5

ZD003NC/UDZSNP5.6B

R001 4.3K OHM 1/8W

C004

NC/0.001uF

ZD002NC/UDZSNP5.6B

R002 2K4 1/8W

C008NC/0.1uF

R006 910R 1/8W

SW002

SW

21

3 4

5

SW004

SW

21

3 4

5

C003
NC/0.001uF

ZD005NC/UDZSNP5.6B

R004 4.3K OHM 1/8W

SW003

SW

21

3 4

5

SW006

SW

21

3 4

5

C002
NC/0.001uF

SW005

SW

21

3 4

5

ZD001NC/UDZSNP5.6B

27

Meridian 1

7. PCB Layout

7.1 Main Board

715G3108-1

28

Meridian 1

C101 D3 C119 C3 C420 B2 C448 C3 CN403 C1 Q302 B3 R114 C3 R136 C2 R403 C4 R425 B2 R467 C4 U105 C2

C102 C3 C120 C2 C421 C2 C701 B1 CN405 C4 Q401 C4 R115 C3 R137 C2 R405 C2 R429 B4 R468 C4 U106 C3

C103 C4 C301 A3 C422 C2 C702 B1 CN406 C1 Q402 B4 R116 C3 R138 C2 R406 C4 R431 B4 R469 B4 U107 C2

C104 C4 C302 B4 C423 B3 C703 B1 CN701 B1 Q701 B1 R117 C3 R139 C2 R407 C3 R436 C1 R470 B4 U401 B3

C105 C3 C303 B4 C430 B3 C704 B2 D701 B1 R101 C4 R118 C2 R140 C2 R408 C1 R437 C1 R471 B4 U402 B2

C106 C3 C304 B4 C431 B1 C705 B2 D702 D1 R102 C4 R119 C2 R141 B3 R409 B2 R438 C1 R472 C4 U403 B4

C107 C3 C305 B3 C432 C1 C706 B1 FB101 C3 R103 C4 R120 C1 R142 D3 R411 C1 R439 C1 R701 B1 U701 A2

C108 C3 C306 B3 C433 C1 C707 B2 FB102 C3 R104 C4 R121 C2 R143 C4 R412 C4 R440 B4 R702 B1 U702 B2

C109 C3 C401 C2 C434 C1 C708 A1 FB103 C3 R105 C3 R122 C2 R144 C4 R414 B2 R441 B4 R703 B1 U703 A2

C110 C3 C403 C2 C435 C1 C709 A2 FB105 C3 R106 C4 R126 C2 R301 A4 R415 C1 R443 C1 R704 B1 X401 C2

C111 C3 C404 C3 C436 C1 C710 B1 FB401 C3 R107 C4 R127 C3 R303 B4 R416 B2 R444 C1 R705 B1 ZD104 D3

C112 C4 C406 B2 C438 B3 C711 A1 FB403 B2 R108 C3 R128 C2 R304 B4 R417 B2 R445 C1 R706 B1 ZD105 C3

C113 C3 C407 B2 C439 C3 CN101 D3 FB404 B4 R109 C3 R129 C2 R305 B4 R418 B2 R446 C1 R707 B1 ZD401 C2

C114 C3 C410 C2 C440 C3 CN102 D2 FB406 C3 R110 C3 R130 C2 R306 B3 R419 B3 R454 B1 R710 B1 ZD402 C1

C115 D1 C411 B4 C442 B3 CN301 A3 FB407 C3 R111 C3 R131 C2 R307 B3 R420 A3 R462 C2 U102 C2 ZD403 C1

C117 C1 C412 B3 C446 C3 CN401 C1 FB701 C1 R112 C3 R132 C3 R401 C3 R421 B4 R465 C4 U103 D3

C118 C2 C413 B3 C447 C3 CN402 C1 Q301 B4 R113 C4 R134 C3 R402 C4 R422 C4 R466 C4 U104 C4

29

Meridian 1

30

Meridian 1

7.2 Power Board

715G2892-1A-4

BD901 C3 CN602 B5 IC601 D5 J904 A3

C604 C5 CN603 C5 IC902 C3 J905 C4

C804 B2 CN801 A1 IC903 C3 J907 B3

C817 B1 CN802 A1 J601 C5 J909 A3

C819 A1 CN803 C1 J602 D5 J910 A4

C820 A1 CN804 D1 J603 D5 J911 A3

C821 C1 CN901 D2 J604 D4 J921 C4

C822 C1 CN902 A5 J605 D5 L801 A2

C900 B4 D801 A2 J606 C5 L802 D1

C902 D3 D901 B3 J607 B5 L901 C3

C903 D2 D903 B4 J806 B3 L905 B3

C907 D3 D904 C4 J810 B3 L906 A4

C908 C2 D905 A3 J816 C2 L907 A5

C909 C3 D906 A3 J817 B2 NR901 C2

C911 B4 D907 B4 J818 A2 PT801 B1

C913 C4 D908 C4 J819 B2 Q901 C5

C918 B3 F901 D2 J820 A2 Q904 C3

C920 A3 F902 A5 J821 C2 R828 C1

C921 A4 F903 B5 J822 B2 R904 C2

C922 A5 FB602 B5 J823 A2 R906 B4

C925 A5 FB901 C4 J901 A4 R924 C4

C931 A5 FB902 D2 J902 C4 T901 B4

CN601 D3 GND1 D1 J903 C4 ZD901 C3

31

Meridian 1

C601 D5 C914 C4 R609 D5 R839 C2 R925 C3

C602 D5 C915 C4 R610 C5 R840 D1 R928 C3

C603 D5 C916 B3 R612 C5 R841 D1 R929 B3

C606 D5 C917 B3 R801 A2 R842 C2 R930 B3

C608 D5 C923 C2 R802 A3 R843 C2 R931 C3

C609 D5 C924 C3 R803 B2 R844 D1 R932 C3

C610 D3 C926 A5 R804 B2 R845 D1 R933 C3

C611 D3 C927 C4 R806 B2 R900 C2 R934 C4

C612 D5 D803 A2 R807 A2 R901 C2 R935 C3

C613 C5 D806 C1 R808 A2 R902 C2 RJ801 B2

C801 B2 D807 C1 R809 A2 R903 B3 RJ802 A3

C802 B2 D808 D1 R810 A2 R905 C2 RJ803 A2

C803 A3 IC801 A2 R811 A2 R907 C2 RJ804 A2

C805 A2 IC901 C4 R812 B2 R908 C4 RJ805 B3

C806 A2 Q608 C5 R813 A2 R909 B3 RJ806 B2

C807 A2 Q802 A2 R815 A2 R910 B3 RJ807 C1

C808 A2 Q805 B2 R816 B2 R912 B3 RJ808 A2

C809 A2 Q806 B2 R817 B2 R913 C4 RJ809 D1

C810 A2 R601 C5 R818 B2 R914 C3 RJ810 A2

C811 B2 R602 D5 R819 B2 R916 C3 RJ811 A2

C812 A2 R603 D5 R820 B2 R917 B4 RJ812 A2

C813 C2 R604 D3 R821 B2 R918 B4 RJ813 A3

C814 B2 R605 D3 R830 C1 R919 C3 RJ814 B2

C815 B2 R606 D5 R836 B2 R920 C3 RJ816 A3

C818 A2 R607 D5 R837 B2 R921 C4 ZD802 B2

C912 C4 R608 D4 R838 C2 R923 C4 ZD803 B2

32

Meridian 1

7.3 Key Board

715G2836-1-2

CN001 B5 SW002 B2

D001 B3 SW003 B1

GND1 A1 SW004 B3

GND2 A4 SW005 B4

SW001 B2 SW006 B4

C001 A4 C010 B1 R006 B4

C002 A2 C011 B4 ZD001 B2

C003 B3 J001 A4 ZD002 B4

C004 B4 J002 A3 ZD003 B1

C005 A4 R001 A2 ZD004 B2

C006 B2 R002 B2 ZD005 B3

C007 B4 R003 B2 ZD006 B4

C008 B2 R004 B3

C009 B3 R005 B3

33

Meridian 1

8. Wiring Diagram

Main Board

9Pin

30 Pin

Panel

D-SUB

NT68667UFG/C (U401)

CN301

1

9

CN701

7Pin

1

7

CN402

Power Board

A

C IN

CN902

1

9

CN801

CN901

10Pin

CN102

Key Board

6

Pin

16

CN001

1

2

CN802

CN804

CN803

29

30

DVI

34

Meridian 1

9. Scalar Board Overview

MSTAR chip

Flash ROM

DC-DC Converters

D-Sub ESD

DVI ESD

35

Meridian 1

10. Mechanical Instructions

1. Place the monitor face down on a smooth surface .Be careful to avoid scratch and injury during the process of

uninstall.

2. Remove three screws remarked in red to remove the Stand-Base ASS’Y.

36

Meridian 1

3. Use disassembly tool to open 7 latches at top, 6 latches at bottom, 5 latches at left and 5 latches at right of

bezel, and remove bezel.

4. Remove rear cover.

5. Remove main frame.

A. Disconnect four connectors and two screws.

37

Meridian 1

B. Press to release left and right latches of LVDS cable, and then disconnect it.

6. Remove Power Board and Main Board.

A. Remove four screws and

PW Shielding.

38

Meridian 1

B. Remove four screws to remove the Power Board and Main Board from Main Frame.

C. Disconnect three connectors from Main Board.

39

Meridian 1

11. Repair Flow Chart

11.1 Main Board

(1). No Power

No power

Press power key and look if the

picture is normal

Please reinsert and make sure

the AC of 100-240 is normal

Reinsert or check the
Adapter/Inverter section

X401 oscillate waveforms are normal

Check C706, C707 and U703

Replace U401

Replace X401

OK

OK

OK

NG

NG

NG

NG

Measure U703 PIN2=3.3V

40

Meridian 1

(2). No Picture

No picture

The button if under control

Replace U401

Replace X401

Measure U703 PIN2=3.3V

Check Correspondent
component

X401 oscillate waveform is normal

Check C706, C707 and U703

OK

OK

OK

OK

OK

NG

NG

NG

NG

Check reset circuit of
U401 is normal

Check HS VS from CN101 is normal

Replace X401

Check Correspondent
component

NG

NG

OK

Replace U401

X401 oscillate
waveform is normal

41

Meridian 1

(3). White screen

White screen

Check Q301, Q302 is broken or CN301 solder?

Check Correspondent
com

p

onent.

Replace Panel

Check Correspondent
component.

Replace U401

OK

OK

Replace X401

OK

NG

NG

NG

NG

Check reset circuit of U401 is normal

OK

X401 oscillate waveform is normal

Measure Q302 base is low level?

42

Meridian 1

11.2. Power/Inverter Board

(1) No power

Check ZD901 ＝16V

Check AC line volt 100V or 240V

Check AC input

Check the voltage of C907 (+)

Check bridge rectified circuit and F901 circuit

Check start voltage for the pin8 of IC901

Check R908 and Change IC901

NG

Check the auxiliary voltage is bigger

than 16V and smaller than 32V

1) Check IC901

2) Check R913, D904 circuit

OK

OK

NG

Check Q901, D907, IC902, IC903, D901, D906

OK

Check IC901 pin5 PWM wave

OK

Check IC901

NG

NG

NG

OK

NG

43

Meridian 1

(2) W / LED, No Backlight

Check ZD901 ＝16V

NG

OK

Check adapter or MB

Check ON/OFF signal

Check Main Board

NG

OK

Check IC801 PIN6, PIN10=16V

NG

OK

Check ZD802, ZD803

Check IC801 PIN8, 9 have the output of square wave at short time

NG

OK

Change IC801

Check Q805 and Q806 have the output of square wave at short time.

NG

OK

Check Q805, Q806

Check the output of PT801

Check connecter & lamp

OK

NG

Change PT801

44

Meridian 1

11.3 Key Board

OSD is unstable or not working

Is Key Pad Board connecting normally?

Connect Key Pad Board

Is Button Switch normally?

Replace Button Switch

Y

N

N

Is Key Pad Board normally?

Replace Key Pad Board

Y

N

Y

Check Main Board

45

Meridian 1

12. ISP Instruction

When do the parts, need the tools as follow:

A. An i486 (or above) personal computer or compatible.

B. Microsoft operation system Windows 95/98/2000/XP.

C. “EasyUSB WriterV4.1” program

D. Software ISP SN Alignment kits

The kit contents:

a. ISP BOARD x1

b. Printer cablex1

c. VGA cable x1

12.1 Install the “EasyUSB WriterV4.1”

.

12.2 Connect the ISP board as follow:

12.3 The process of ISP write is as follows.

Connect to

the PC LPT

Connect to the

Philips 220E1

46

Meridian 1

a) Double-click ，running the program as follows:

b) Click

icon and the program runs as follows:

47

Meridian 1

c) Click icon, search the program “Philips_220E1_NT68667_CMO_M216H1L01_20081219_V100”, or

“Philips_220E1_NT68667_CMO_M216H1L01_Aonly_20081219_V100” and click open:

d) Click

icon. If it burns successfully, it will show as the follow picture:

48

Meridian 1

13. DDC Instruction

General

DDC Data Re-programming

In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect,

repaired monitor’ the serial numbers have to be re-programmed.

It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circuit

board have been replaced, in this case the DDC data does not need to be re-programmed.

Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards

Association (VESA). Extended Display Identification Data (EDID) information may be also obtained from VESA.

1. An i486 (or above) personal computer or compatible.

2. Microsoft operation system Windows 95/98/2000/XP.

3. “PORT95NT.exe, WinDDC” program.

4. Software OSD SN Alignment kits

The kit contents:

a. OSD SN BOARD x1

b. Printer cablex1

c. VGA cable x1

d. 12V DC power source

13.1. Install the “PORT95NT.EXE”, and restart the computer.

The process of installing “PORT95NT” has been specified in, so it will not be specified again. If you have any

problem, please read it.

13.2 Connect the DDC Board as follow:

Connect to the

PC LPT

When you write analog

EDID, Connect this port

to the Philips 220E1’s

VGA port

12V Input

49

Meridian 1

Take analog DDC write for example, as follow

a. Double-click

，appear as follow Figs：

50

Meridian 1

b. Click

c. Click

, and key in 14 numbers in the Serial Number Blank, then click “OK”, Now analog DDC Write

complete, as follow:

Note:

The way of digital DDC Write is the same as analog.

51

Meridian 1

220E1 EDID

Analog

128 bytes EDID Data (Hex):

00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15

0: 00 FF FF FF FF FF FF 00 41 0C 2E C0 6A B7 0A 00

16: 59 0F 01 03 6C 2F 1A 78 2E 35 85 A6 56 48 9A 24

32: 12 50 54 2F 6F 00 71 4F 81 80 81 8A 95 00 A9 40

48: B3 00 81 40 D1 C0 02 3A 80 18 71 38 2D 40 58 2C

64: 45 00 DC 0C 11 00 00 1E 00 00 00 FF 00 31 32 33

80: 34 35 38 39 37 30 32 33 31 34 00 00 00 FD 00 38

96: 4C 1E 53 15 00 0A 20 20 20 20 20 20 00 00 00 FC

112: 00 50 68 69 6C 69 70 73 20 32 32 30 45 0A 00 67

Decoded EDID data

<---Header--->

Header: 00 FF FF FF FF FF FF 00

<-x-Header-x->

<---Vendor/Product Identification--->

ID Manufacturer Name: PHL

ID Product Code: C02E

ID Serial Number: 000ab76a

Week of Manufacture: 89

Year of Manufacture: 2005

<-x-Vendor/Product Identification-x->

<---EDID Structure Version/Revision--->

EDID Version#: 01

EDID Revision#: 03

<-x-EDID Structure Version/Revision-x->

<---Basic Display Parameters/Features--->

Video i/p definition: Analog

Signal Level Standard: 0.700V/0.000V (0.700Vpp)

Setup: Blank-to-Black not expected

52

Meridian 1

Separate Sync Support: Yes

Composite Sync Support: Yes

Sync. on green video supported:No

Serration of the Vsync.Pulse is not required.

Max. H. Image Size: 47cm.

Max. V. Image Size: 26cm.

Display Gamma: 2.2

DPMS Features, Active off: Yes.

Display Type: R/G/B color display.

Standard Default Color Space: Yes.

Preferred Timing Mode: Yes

<---Basic Display Parameters/Features--->

<---Color Characteristics--->

Red x: 0.6484375000

Red y: 0.3388671875

Green x: 0.2812500000

Green y: 0.6025390625

Blue x: 0.1425781250

Blue y: 0.0703125000

White x: 0.3125000000

White y: 0.3291015625

<-x-Color Characteristics-x->

<---Established Timings--->

Established Timings 1: 2F

-640x480 @60Hz VGA, IBM

-640x480 @72Hz VESA

-640x480 @75Hz VESA

-800x600 @56Hz VESA

-800x600 @60Hz VESA

Established Timings 2: 6F

-800x600 @75Hz VESA

-832x624 @75Hz Apple, Mac II

-1024x768 @60Hz VESA

-1024x768 @70Hz VESA

-1024x768 @75Hz VESA

-1280x1024 @75Hz VESA

Established Timings 3: 00

<-x-Established Timings-x->

<---Standard Timing Identification--->

53

Meridian 1

-1152x864 @75

-1280x1024 @60

-1280x1024 @70

-1440x900 @60

-1600x1200 @60

-1680x1050 @60

-1280x960 @60

-1920x1080 @60

<-x-Standard Timing Identification-x->

<---Detailed Timing Descriptions--->

Detailed Timing: 1920x1080 @ 60Hz

<-x-Detailed Timing Descriptions-x->

<---Detailed Timing Descriptions--->

Detailed Timing: FF (Monitor SN) '123458970231'

Detailed Timing: FD (Monitor limits)

Min. V. rate: 56Hz

Max. V. rate: 76Hz

Min. H. rate: 30 KHz

Max. H. rate: 83 KHz

Max. Pixel Clock: 210MHz

Detailed Timing: FC (Monitor Name) 'Philips 220E'

<-x-Detailed Timing Descriptions-x->

Extension Flag: 00

Checksum: 67

54

Meridian 1

Digital (only for 220E1SB/69)

128 bytes EDID Data (Hex):

00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15

0: 00 FF FF FF FF FF FF 00 41 0C 2E C0 8E 41 0C 00

16: 4F 0F 01 03 80 2F 1A 78 2E 35 85 A6 56 48 9A 24

32: 12 50 54 2F 6F 00 71 4F 81 80 81 8A 95 00 A9 40

48: B3 00 81 40 D1 C0 02 3A 80 18 71 38 2D 40 58 2C

64: 45 00 DC 0C 11 00 00 1E 00 00 00 FF 00 31 32 33

80: 34 35 37 39 38 30 33 32 31 34 00 00 00 FD 00 38

96: 4C 1E 53 15 00 0A 20 20 20 20 20 20 00 00 00 FC

112: 00 50 68 69 6C 69 70 73 20 32 32 30 45 0A 00 AD

Decoded EDID data

<---Header--->

Header: 00 FF FF FF FF FF FF 00

<-x-Header-x->

<---Vendor/Product Identification--->

ID Manufacturer Name: PHL

ID Product Code: C02E

ID Serial Number: 000c418e

Week of Manufacture: 79

Year of Manufacture: 2005

<-x-Vendor/Product Identification-x->

<---EDID Structure Version/Revision--->

EDID Version#: 01

EDID Revision#: 03

<-x-EDID Structure Version/Revision-x->

<---Basic Display Parameters/Features--->

Video i/p definition: Digital

Max. H. Image Size: 47cm.

Max. V. Image Size: 26cm.

55

Meridian 1

Display Gamma: 2.2

DPMS Features, Active off: Yes.

Display Type: R/G/B color display.

Standard Default Color Space: Yes.

Preferred Timing Mode: Yes

<---Basic Display Parameters/Features--->

<---Color Characteristics--->

Red x: 0.6484375000

Red y: 0.3388671875

Green x: 0.2812500000

Green y: 0.6025390625

Blue x: 0.1425781250

Blue y: 0.0703125000

White x: 0.3125000000

White y: 0.3291015625

<-x-Color Characteristics-x->

<---Established Timings--->

Established Timings 1: 2F

-640x480 @60Hz VGA, IBM

-640x480 @72Hz VESA

-640x480 @75Hz VESA

-800x600 @56Hz VESA

-800x600 @60Hz VESA

Established Timings 2: 6F

-800x600 @75Hz VESA

-832x624 @75Hz Apple,Mac II

-1024x768 @60Hz VESA

-1024x768 @70Hz VESA

-1024x768 @75Hz VESA

-1280x1024 @75Hz VESA

Established Timings 3: 00

<-x-Established Timings-x->

<---Standard Timing Identification--->

-1152x864 @75

-1280x1024 @60

-1280x1024 @70

-1440x900 @60

-1600x1200 @60

-1680x1050 @60

56

Meridian 1

-1280x960 @60

-1920x1080 @60

<-x-Standard Timing Identification-x->

<---Detailed Timing Descriptions--->

Detailed Timing: 1920x1080 @ 60Hz

<-x-Detailed Timing Descriptions-x->

<---Detailed Timing Descriptions--->

Detailed Timing: FF (Monitor SN) '123457980321'

Detailed Timing: FD (Monitor limits)

Min. V. rate: 56Hz

Max. V. rate: 76Hz

Min. H. rate: 30 KHz

Max. H. rate: 83 KHz

Max. Pixel Clock: 210MHz

Detailed Timing: FC (Monitor Name) 'Philips 220E'

<-x-Detailed Timing Descriptions-x->

Extension Flag: 00

Checksum: AD

57

Meridian 1

14. White Balance, Luminance Adjustment

1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (PHILIPS 220E.DDCI), Pattern

generator.

2. Equipment installation:

a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart

PC after finish installing

b. Install Port95NT drive program, set PC printer connector mode as ECP mode and reset PC after finish installing.
c. Connect tool as follow:

Note: It’s not necessary to connect Port2.

3. Adjustment

Preparation before adjustment:

a. Monitor should be warmed up for more than half an hour.

b. Make sure that the tools are connected right and drive programs have been installed OK.

Adjustment process:

a. Press the power of CA-210, shut off the lens, press 0-Cal and open the lens after analyzer reset.

b. Open white balance adjustment program, select the right parameter according with the program and click OK.

c. Make sure that the lens of CA-210 aims at the center of the screen, then click START to adjust.

d. After finish adjusting, the adjustment program displays pass, and the START button changes for NEXT, which

means that you can adjust another monitor.

To PC LPT

To BSG-265A or
equivalent instrument

To PC Port 2

Philips 220E1

58

Meridian 1

3. Color Temp confirmation

Connect the signal to the monitor, the monitor displays white-picture, use CA-210 to measure the Color Temp of the

screen center and select the OSD to make sure whether the Color Temps accord with the SPEC.

59

Meridian 1

15. Monitor Exploded View

60

Meridian 1

16. Recommended & Spare Parts List

Recommended Parts List for 220E1SB/69

Item Location Philips 12NC PCM Codes Description Remark

1 FQ106 A34G1082AFLA1B0101 BEZEL 21.6" CMO

1 FQ106 A34G1430AFLA1B0101 BEZEL 21.5" AUO

2 FQ405 996520036036 A33G0313AFL 1L0100 KEY PAD

3 FQ004 KEPC9QP3 KEY BOARD ASSY

4 E750 750GLM216H1132M0PH PANEL M216H1-L01 C1 NB CMO

4 E750 750GLM216H1132N000 PANEL M216H1-L01 C1 NB CMO

2nd

source

4 E750 750GLU215H1043N000 PANEL M215HW01 V00G XM AUO

4 E750 750GLU215H1043M0PH PANEL M215HW01 V00G XM AUO

2nd

source

4 E750 750GLU215H1053M0PH PANEL M215HW01 V00H XM AUO

2nd

source

4 E750 750GLU215H1053N000 PANEL M215HW01 V00H XM AUO

2nd

source

4 E750 750GLU215H1063M0P PANEL M215HW01 V00J XM AUO

2nd

source

4 E750 750GLU215H1063N000 PANEL M215HW01 V00J XM AUO

2nd

source

5 FQ002 996520037004 756GQ8CB PH005

SCALER BOARD ASSY
(CBPCRNDPHQ1)

CMO

5 FQ002 756GQ9CB PH065 00

SCALER BOARD ASSY
(CBPCRNDPHQ1)

AUO

6 FQ003 PWPC8B41MQCW POWER BOARD ASSY

7 FQ105 996520036099 A34G0897AFL 3B0100 REAR COVER 21.5″

8 FQ103 996520036033 705GQ834617 21.5″ LCD STAND BASE ASS'Y

FQ307 996510014810 089G 725HAA DB D-SUB CABLE

E08907 996520036014 089G179J30N 12 FFC CABLE

FQ301 996510019911 089G410A15N IS POWER CORD WALL-OUT FOR UK

FQ205 996520036084 705GQ9CS002 CUSHION ASSY

FQ202 Q44GC085813 2D 21.6 LCD CARTON

IC902 996500036055 056G 139 3A IC PC123Y22FZ0F

T901 S80GL22T3V1 XFMR POWER 490uH TPV-PT

PT801 S80GL24T23V XFMR POWER 68uH TPV-PT VOC

IC901 996520036091 056G 379128 IC LD7576 GS SOP-8

IC801 996510018159 056G 608 12 IC TA9687GN-A-0-TR SOP-16

F901 084G 56 4W FUSE 4.0A 250V

F902 084G 56 4W FUSE 4.0A 250V

IC903 996500036054 056G 158 12 KIA431A-AT/P TO-92

U402 996520037005 100GPNMC000NT1 MCU ASSY(056G1133713) CMO

U402 100GPNAI000NT1 MCU ASSY(056G1133713) AUO

X401 093G 2251B

CRYSTAL
MXS12.000AC20F-KAB10HC-49/US

U401 996520037006 056G 562583 IC NT68667UFG/C QFP-128L

U702 996500035963 056G 563 31 IC AZ1117D-1.8-E1

U703 056G 563515

IC AZ1117D-3.3TRG1 1A/3.3V
TO-252

U103 996510014826 056G 662 13 IC AZC099-04S SOT23-6L

U104 996510014826 056G 662 13 IC AZC099-04S SOT23-6L

U105 996510014826 056G 662 13 IC AZC099-04S SOT23-6L

U106 996510014826 056G 662 13 IC AZC099-04S SOT23-6L

U107 996520037007 056G 662502 IC ESD AZC199-04S SOT23-6L

Spare Parts List (only for 220E1SB/93)

Location PCM Codes Description Remark

FQ307 089G 725HAA DB D-SUB CABLE

V50B/C

V00G/H/J

E08907 089G179J30N 12 FFC CABLE

FQ301 089G414A15N IS POWER CORD

E750 750GLU215H1533M0PH PANEL M215HW01 V50B XM AUO
E750 750GLU215H1533N000 PANEL M215HW01 V50B XM AUO
E750 750GLU215H1543M0PH PANEL M215HW01 V50C XM AUO

E750 750GLU215H1543N000 PANEL M215HW01 V50C XM AUO
FQ405 A33G0313AFL 1L0100 KEY PAD
FQ105 A34G0897AFL 3B0100 REAR COVER 21.5
FQ106 A34G1430AFLA1B0101 BEZEL 21.5

FQ205 705GQ9CS154 CUSHION ASSY

AUO

V50B/C

FQ209 Q44GC085301EPE EPE
FQ202 Q44GC085813 5D 21.6 LCD CARTON
FQ210 Q45G 88606 R PE BAG FOR BASE
FQ203 Q45G 88609204 N EPE BAG

E08907 S89G179T30N12 LVDS ASSY

FQ206 Q41G780A81320A QSG 220E
FQ204 Q70G2201813 3A CD MANUAL 220E
FQ103 705GQ834617 21.6 LCD STAND BASE ASSY

FQ002 756GQ9CB PH066 00 SCALER BOARD ASSY(CBPCRNDPHQ1)

AUO

V50B/C

U402 100GPNAI002NT1 MCU ASSY(056G1133713)

AUO

V50B/C

CN402 033G3802 7 WAFER EH 7
CN701 033G3802 9 WAFER 9P RIGHT ANELE PITCH
CN301 033G801930F CH JS CONNECTOR
CN101 088G 35315F HD D-SUB CONN F ATTACHED SCREW
CN101 088G 35315F HX D-SUB 15PIN F

62

Meridian 1

CN101 088G 35315F XH D-SUB 15PIN VERTICAL CONN WITH SCREW
CN102 088G 35424F C DVI 24PIN CONN F
CN102 088G 35424F D DVI 24PIN CONN F ATTACHED SCREW
CN102 088G 35424F N DVI 24PIN CONN F
CN102 088G 35424F XH DVI 24PIN CONN F ATTACHED SCREW

X401 093G 22 51 H CRYSTAL

X401 093G 2251B CRYSTAL MXS12.000AC20F-KAB10HC-49/US

C305 067G 3151014KB EC 100uF M 25V 6.3*11

C704 067G 3151014KB EC 100uF M 25V 6.3*11

C706 067G 3151014KB EC 100uF M 25V 6.3*11

C707 067G 3151014KB EC 100uF M 25V 6.3*11

U401 056G 562583 IC NT68667UFG/C QFP-128L

U702 056G 563 31 IC AZ1117D-1.8-E1

U703 056G 563 52 IC AP1117D33G-13 TO252-3L DIODES

U703 056G 563515 IC AZ1117D-3.3TRG1 1A/3.3V TO-252

U103 056G 662 13 IC AZC099-04S SOT23-6L

U104 056G 662 13 IC AZC099-04S SOT23-6L

U105 056G 662 13 IC AZC099-04S SOT23-6L

U106 056G 662 13 IC AZC099-04S SOT23-6L

U107 056G 662502 IC ESD AZC199-04S SOT23-6L

U403 056G1133 56 M24C16-WMN6TP

U402 056G1133713 IC PM25LV010A-100SCE SOIC-8

Q302 057G 417 12 T KEC 2N3904S-RTK/PS

Q701 057G 417 12 T KEC 2N3904S-RTK/PS

Q301 057G 763 1 A03401 SOT23 BY AOS(A1)

R471 061G0402000 RST CHIP MAX 0R05 1/16W

R472 061G0402000 RST CHIP MAX 0R05 1/16W

R134 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R132 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R131 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R130 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R129 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R128 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R127 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R126 061G0402100 RST CHIPR 10 OHM +-5% 1/16W

R117 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R118 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R119 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R402 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R409 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R417 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R429 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R431 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R103 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R104 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R101 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R105 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R109 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R111 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R113 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R114 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R115 061G0402101 RST CHIPR 100 OHM +-5% 1/16W

R706 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R425 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R416 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R415 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R142 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R141 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R139 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R120 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W

R414 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R702 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R705 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R411 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R408 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R405 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R403 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R306 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R303 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W

R462 061G0402105 RST CHIPR 1MOHM +-5% 1/16W

R418 061G0402121 RST CHIP 120R 1/16W 5%

R407 061G0402203 RST CHIP 20K 1/16W 5%

R107 061G0402222 RST CHIPR 2.2 KOHM +-5% 1/16W

R106 061G0402222 RST CHIPR 2.2 KOHM +-5% 1/16W

R444 061G0402390 1F RST CHIPR 3.9KOHM +-1% 1/16W

R443 061G0402390 1F RST CHIPR 3.9KOHM +-1% 1/16W

R401 061G0402470 0F RST CHIPR 0402 470 OHM +-1% 1/16W

R110 061G0402471 RST CHIPR 470 OHM +-5% 1/16W

R704 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R441 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R440 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R144 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R143 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R138 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R137 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W

R304 061G0402473 RST CHIPR 47 KOHM +-5% 1/16W

64

Meridian 1

R307 061G0402473 RST CHIPR 47 KOHM +-5% 1/16W

R116 061G0402750 RST CHIPR 75 OHM +-5% 1/16W

R112 061G0402750 RST CHIPR 75 OHM +-5% 1/16W

R108 061G0402750 RST CHIPR 75 OHM +-5% 1/16W

R102 061G0603101 RST CHIPR 100 OHM +-5% 1/10W

R305 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA

R305 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN

R419 061G0805121 JF RST CHIPR 120 OHM +- 5% 1/8W FENGHUA

R420 061G0805121 JF RST CHIPR 120 OHM +- 5% 1/8W FENGHUA

R420 061G0805121 JT RST CHIPR 120OHM +- 5% 1/8W TZAI YUAN

R419 061G0805121 JT RST CHIPR 120OHM +- 5% 1/8W TZAI YUAN

R301 061G1206331 RST CHIPR 330 OHM +-5% 1/4W

C107 065G040210232K A CAP 0402 1NF K 50V X7R

C423 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C430 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C431 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C432 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C433 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C434 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C435 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C442 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C446 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C447 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C448 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C705 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C711 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C709 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C708 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C306 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C115 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C301 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C302 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C403 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C404 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C406 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C407 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C410 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C412 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C413 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C422 065G040210412K A CAP CHIP 0402 100nF K 16V X7R

C104 065G040222031J A CAP 0402 22PF J 50V NPO

C420 065G040222031J A CAP 0402 22PF J 50V NPO

C421 065G040222031J A CAP 0402 22PF J 50V NPO

C103 065G040222031J A CAP 0402 22PF J 50V NPO

C401 065G040222417Z T CAP CHIP 0402 0.22UF 16V Y5V

C411 065G040222417Z T CAP CHIP 0402 0.22UF 16V Y5V

C114 065G040247312K A 8.31HIP 0402 47nF K 16V X7R

C111 065G040247312K A 8.31HIP 0402 47nF K 16V X7R

C110 065G040247312K A 8.31HIP 0402 47nF K 16V X7R

C108 065G040247312K A 8.31HIP 0402 47nF K 16V X7R

C106 065G040247312K A 8.31HIP 0402 47nF K 16V X7R

C102 065G040247312K A 8.31HIP 0402 47nF K 16V X7R

C105 065G040250931J A CAP 0402 5PF J 50 NPO

C109 065G040250931J A CAP 0402 5PF J 50 NPO

C113 065G040250931J A CAP 0402 5PF J 50 NPO

C439 065G060310512K 3 MLCC 0603 CAP 1uF K 16V X7R

C440 065G060310512K 3 MLCC 0603 CAP 1uF K 16V X7R

C438 065G0805105 12 1UF +-10% 16V X7R

FB404 071G 56V301 B CHIP BEAD FCM2012VF-301T07 BULLWILL
FB406 071G 56V301 B CHIP BEAD FCM2012VF-301T07 BULLWILL
FB407 071G 56V301 B CHIP BEAD FCM2012VF-301T07 BULLWILL
FB403 071G 56V301 B CHIP BEAD FCM2012VF-301T07 BULLWILL
FB401 071G 56V301 B CHIP BEAD FCM2012VF-301T07 BULLWILL
FB105 071G 59B121 TB160808B
FB701 071G 59G301 CHIP BEAD 300OHM
FB101 071G 59K190 B 19 OHM BEAD
FB102 071G 59K190 B 19 OHM BEAD
FB103 071G 59K190 B 19 OHM BEAD

D702 093G 60505 DIO SIG SM BAT54C(PHSE)R
ZD403 093G 39GA01 T RLZ5.6B
ZD401 093G 39GA01 T RLZ5.6B
ZD105 093G 39GA01 T RLZ5.6B
ZD104 093G 39GA01 T RLZ5.6B

D701 093G3004 3 SM340A

D702 093G 60518SEM DIODE BAT54C-HAF 300mA/30V SOT-23

Q301 057G 763513 P6403FMG BY NIKO-SEM

Q302 057G 417518 TRA LMBT3904LT1G 200mA/40V SOT-23 LRC

Q701 057G 417518 TRA LMBT3904LT1G 200mA/40V SOT-23 LRC

FQ003 PWPC9B41AQYO POWER BOARD ASSY

AUO

V50B/C

GND1 009G6005 1 GROUND TERMINAL
CN801 033G8021 2E F WAFER
CN803 033G8021 2E F WAFER
CN801 033G8021 2E XY CONNECTOR
CN803 033G8021 2E XY CONNECTOR

IC902 056G 139 3A IC PC123Y22FZ0F

66

Meridian 1

IC902 056G 139900 PHOTO COUPLER TLP421F

NR901 061G 58100 WD RST NTCR 10 OHM +-20% 5A THINKING

C908 063G 10747410V 0.47UF 275VAC ARCO
C908 063G107K474 6S CAP X2 0.47UF K 275VAC
C908 063G107K474 US 0.47UF +-10%
C817 065G 6J2096ET 2PF 5% SL 6KV
C902 065G305M1022BP Y2 1000PF M 250VAC Y5P
C903 065G305M1022BP Y2 1000PF M 250VAC Y5P
C900 065G306M3322BP 3300PF 20%
C804 067G215A1024KV EC 1000uF 25V 12.5*20mm
C918 067G215A1024KV EC 1000uF 25V 12.5*20mm
C804 067G215A1024LV LOW ESR EC 1000uF 25V M 12.5*20mm
C918 067G215A1024LV LOW ESR EC 1000uF 25V M 12.5*20mm
C922 067G215S4713KV

EC 105℃ CAP 470UF M 16V
C922 067G215S4713LV LOW ESR EC 470uF 16V M 10*12.5mm
C922 067G215V471 3H

CAP L105℃ 470UF M 16V
C907 067G315Z10115K EC.100UF 450V 18*40mm
C907 067G315Z10115L EC 100uF 450V M 18*40mm

L901 073G 174 65 H2 LINE FILTER 30mH MIN
L901 073G 174 65 S2 LINE FILTER 30mH MIN
L906 073G 253 91 H CHOKE COIL
L905 073G 253 91 H CHOKE COIL
L905 073G 253 91 L CHOKE BY LI TA
L906 073G 253 91 L CHOKE BY LI TA
T901 080GL22T 3 N1 XFMR 490uH YUVA-1093
T901 080GL22T 3 S1 XFMR 490uH

PT801 080GL24T 23 DN XFMR 68uH TK.2005Y.101 VOC
CN901 087G 501 32 S AC SOCKET
CN901 087G 501 32 DL AC SOCKET DIP 3PIN+2PIN GROUND
BD901 093G 50460 28 BRIDGE DIODE KBP208G LITEON
BD901 093G 50460502 KBP206G
CN902 095G 825 9D 11 HARNESS 9P(SCN)-10P 100mm
CN902 095G 825 9X 11 HARNESS 9P(SCN)-10P 100mm

T901 S80GL22T3V1 XFMR POWER 490uH TPV-PT

PT801 S80GL24T23V XFMR POWER 68uH TPV-PT VOC

IC901 056G 379128 IC LD7576 GS SOP-8
IC801 056G 608 12 IC ta9687GN-A-0-TR SOP-16

Q802 057G 759 2 RK7002FD5T116 SOT-23 BY ROHM
Q806 057G 763 91 ET AO4620 7.2A/30V -5.3A/-30V SOIC-8
Q805 057G 763 91 ET AO4620 7.2A/30V -5.3A/-30V SOIC-8
R905 061G0603000 RST CHIP MAX 0R05 1/10W
R928 061G0603100 1F RST CHIPR 1 KOHM +-1% 1/10W
R920 061G0603100 1F RST CHIPR 1 KOHM +-1% 1/10W

R907 061G0603100 1F RST CHIPR 1 KOHM +-1% 1/10W
R916 061G0603100 2F RST CHIPR 10K OHM +-1% 1/10W
R918 061G0603100 2F RST CHIPR 10K OHM +-1% 1/10W
R807 061G0603103 RST CHIPR 10 KOHM +-5% 1/10W
R813 061G0603104 RST CHIPR 100 KOHM +-5% 1/10W
R806 061G0603104 RST CHIPR 100 KOHM +-5% 1/10W
R809 061G0603105 RST CHIPR 1M OHM +-5% 1/10W
R808 061G0603390 0F RST CHIPR 390 OHM +-1% 1/10W
R836 061G0603563 Y RST CHIPR 56KOHM +-5% 1/10W YAGEO
R810 061G0603750 2F RST CHIPR 75KOHM +-1% 1/10W
R837 061G0603752 RST CHIPR 7.5 KOHM +-5% 1/10W

R925 061G0603910 1F RST CHIPR 9.1 KOHM +-1% 1/10W
RJ806 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA
RJ807 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA
RJ803 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA
RJ804 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA
RJ805 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA
RJ808 061G0805000 JF RST CHIPR 0 OHM +-5% 1/8W FENGHUA
RJ803 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN
RJ804 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN
RJ805 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN
RJ806 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN
RJ808 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN
RJ807 061G0805000 JT RST CHIPR 0 OHM +- 5% 1/8W TZAI YUAN

R801 061G08051002FF RST CHIPR 10KOHM +-1% 1/8W FENGHUA

R801 061G08051002FY RST CHIPR 10KOHM +-1% 1/8W YAGEO

R812 061G08051003FF RST CHIPR 100KOHM +-1% 1/8W FENGHUA

R812 061G08051003FY RST CHIPR 100KOHM +-1% 1/8W YAGEO

R919 061G08051500FF RST CHIPR 150OHM +-1% 1/8W FENGHUA

R919 061G08051500FT RST CHIPR 150 OHM +-5% 1/8W

R802 061G0805220 RST CHIPR 22 OHM +-5% 1/8W

R819 061G0805229 RST CHIP 2R2 1/8W 5%

R818 061G0805229 RST CHIP 2R2 1/8W 5%

R817 061G0805229 RST CHIP 2R2 1/8W 5%

R816 061G0805229 RST CHIP 2R2 1/8W 5%

R803 061G0805512 RST CHIPR 5.1 KOHM +-5% 1/8W

R804 061G0805512 RST CHIPR 5.1 KOHM +-5% 1/8W

R830 061G0805512 RST CHIPR 5.1 KOHM +-5% 1/8W

R811 061G0805820 2F RST CHIPR 82KOHM +-1% 1/8W
RJ814 061G1206000 RST CHIP MAX 0R05 1/4W
RJ813 061G1206000 RST CHIP MAX 0R05 1/4W
RJ811 061G1206000 RST CHIP MAX 0R05 1/4W
RJ801 061G1206000 RST CHIP MAX 0R05 1/4W

68

Meridian 1

RJ810 061G1206000 RST CHIP MAX 0R05 1/4W

R917 061G1206100 RST CHIPR 10 OHM +-5% 1/4W

R930 061G1206101 RST CHIPR 100 OHM +-5% 1/4W

R929 061G1206101 RST CHIPR 100 OHM +-5% 1/4W

R912 061G1206101 RST CHIPR 100 OHM +-5% 1/4W

R910 061G1206101 RST CHIPR 100 OHM +-5% 1/4W

R909 061G1206101 RST CHIPR 100 OHM +-5% 1/4W

R903 061G1206101 RST CHIPR 100 OHM +-5% 1/4W

R908 061G1206103 RST CHIPR 10K OHM +-5% 1/4W

R923 061G1206221 RST CHIPR 220 OHM +-5% 1/4W

R913 061G1206519 RST CHIPR 5.1 OHM +-5% 1/4W

R902 061G1206684 RST CHIPR 680K OHM +-5% 1/4W

R901 061G1206684 RST CHIPR 680K OHM +-5% 1/4W

R900 061G1206684 RST CHIPR 680K OHM +-5% 1/4W

C923 065G060310232K A CAP CHIP 0603 1000pF K 50V X7R

C926 065G0603104 12 CER2 0603 X7R 16V 100N P

C924 065G0603104 12 CER2 0603 X7R 16V 100N P

C814 065G060322131J A CAP 0603 220PF J 50V NPO

C810 065G060322232K A CAP 0603 2.2NF K 50V X7R

C805 065G060322332K F CAP CHIP 0603 22NF K 50V X7R

C807 065G060333232K F CAP CHIP 0603 3300PF K 50V X7R

C808 065G060333332K A CAP CHIP 0603 0.033uF K 50V X7R

C914 065G060347131J A CAP CHIP 0603 470PF J 50V NPO

C915 065G080510332K F CAP CHIP 0805 10NF K 50V X7R

C811 065G080510432K A CAP CHIP 0805 100nF K 50V X7R

C815 065G080510432K A CAP CHIP 0805 100nF K 50V X7R

C912 065G080510432K A CAP CHIP 0805 100nF K 50V X7R

C809 065G080522131J Y CAP CHIP 0805 220P 50V NPO +/-5%

C806 065G080522512K T CAP CHIP 0805 2.2UF K 16V X7R

C801 065G080547332K F CAP CHIP 0805 47NF K 50V X7R

C802 065G080547332K F CAP CHIP 0805 47NF K 50V X7R

C927 065G080547332K F CAP CHIP 0805 47NF K 50V X7R

C916 065G120610272K Y CAP CHIP 1206 1NF K 500V X7R

C917 065G120610272K Y CAP CHIP 1206 1NF K 500V X7R

C803 065G120610432K Y CER 1206 100N 50V X7R +/-10%

D806 093G 64 42 PP BAV70 SOT-23

ZD803 093G 39S 24 T RLZ 5.6B LLDS
ZD802 093G 39S 24 T RLZ 5.6B LLDS

D803 093G 6433S DIODE BAV99 SEMTECH

D803 093G 64 33 DIO SIG SM BAV99 (PHSE)R

D806 093G 64 42 L DIODE LBAV70LT1G SOT-23 LRC

ZD802 093G 39GA01 T RLZ5.6B
ZD803 093G 39GA01 T RLZ5.6B

Q802 057G 763511 MOSFET SRK7002LT1G SOT-23 LRC

Q805 057G 600 61 AM4502C-TI-PF S0-8

Q806 057G 600 61 AM4502C-TI-PF S0-8

D806 093G 64S 6 SMT D-BAV70-7-F SOT-23

R820 061G0603100 Y RST CHIPR 10 OHM +-5% 1/10W YAGEO

R821 061G0603100 Y RST CHIPR 10 OHM +-5% 1/10W YAGEO
RJ802 061G1206000 RST CHIP MAX 0R05 1/4W
RJ816 061G1206000 7 RST CHIP MAX 0R05 1/4W

C818 065G0805155A2K T CAP CHIP 0805 1.5UF K 10V X7R

C818 065G0805155A2K 3 CAP CHIP 0805 1.5UF K 10V X7R

C818 065G0805155A2K M CAP MLCC 0805 1.5uF K 10V X7R

C806 065G080522512K M MLCC 0805 CAP 2.2uF 16V X7R

C806 065G080522512K 3 CAP CHIP 0805 2U2 16V X7R +/-10%

R823 061G0805471 JF RST CHIPR 470 OHM +-5% 1/8W FENGHUA

R822 061G1206471 JT RST CHIPR 470 OHM 1/4W TZAI YUAN

D901 093G 52 66 DIODE FMX-12SL 10A/200V TO-220

D901 093G 52 68 DIODE FCF10A20 10A/200V TO-220

D901 093G 52 69 DIODE YG902C2RSC 10A/200V TO-220F15

D906 093G 60251 FCQ10U06

D906 093G 60526 SCHOTTKY MBRF1060CT ITO-220AB

HS2 Q90G6264 5 HEAT SINK
Q901 057G 600 35 STP8NK80ZFP
Q901 057G 667 21 STP10NK70ZFP
Q901 057G 667516 FET 2SK3673 TO-220 FUJI

HS1 090G6064 1 HEAT SINK

CN901 006G 31500 EYELET

R906 061G152M10452T RST MOFR 100KOHM +-5% 2WS
R924 061G152M39852T RST MOFR 0.39 OHM +-5% 2WS
R904 061G152M75052T SY RST MOFR 75OHM +-5% 2WS FUTABA
R828 061G212Y62552T SY RST MGFR 6.2MOHM +-5% 1/2W FUTABA
C911 065G 2K152 2T6921 CAP CER 1500pF K 2KV Y5P
C913 067G215Y2207KT

CAP 105℃ 22UF M 50V KINGNICHI
FB902 071G 55 9 T FERRITE BEAD
FB901 071G 55 29 FERRITE BEAD

F901 084G 56 4 B FUSE 4A 250V
F902 084G 56 4 B FUSE 4A 250V

ZD901 093G 3952152T TZX18B

D903 093G 6026T52T RECTIFIER DIODE FR107
D904 093G 6038T52T FR103
D801 093G 64 1152T 1N4148
D907 093G 64 1152T 1N4148

F901 084G 56 4W FUSE 4.0A 250V
F902 084G 56 4W FUSE 4.0A 250V

70

Meridian 1

D907 093G 6452452T DIODE 1N4148-B4006 DO-35 SEMTECH
D801 093G 6452452T DIODE 1N4148-B4006 DO-35 SEMTECH
D903 093G110050152T DIODE PR1007 1A/1000V 500ns DO-41
C913 067G215S2207RT EC 22uF 50V 5*11mm

C911 065G 2K152 2T6213 CAP CER 1500PF K 2KV
IC903 056G 158 12 KIA431A-AT/P TO-92
IC903 056G 158 10 T IC AS431AZTR-E1 TO-92

Q904 057G 761 16 TRA KTD1028 KEC

C920 067G 2046812KT CS CAP 680uF 10V 8*11 mm

PT801 006G 31502 1.5MM RIVET

C819 095G 90 23 JUMPER WIRE

C821 095G 90 23 JUMPER WIRE

FQ004 KEPC9QP3 KEY BOARD ASSY

D001 081G 12 1F GP LED 3 GP32032M/G307-ZY-50-C

CN001 095G820H 6W514 WIRE HARNESS 6P(SANW)-7P(PH) 200MM

CN001 095G820H 6X514 WIRE HARNESS 6P(SANW)-7P(PH) 200MM
SW006 077G 603 AI HJ TACT SWITCH 2PIN
SW005 077G 603 AI HJ TACT SWITCH 2PIN
SW003 077G 603 AI HJ TACT SWITCH 2PIN
SW004 077G 603 AI HJ TACT SWITCH 2PIN
SW002 077G 603 AI HJ TACT SWITCH 2PIN
SW001 077G 603 AI HJ TACT SWITCH 2PIN
SW001 077G 603 AI CJ TACT SWITCH 2PIN
SW002 077G 603 AI CJ TACT SWITCH 2PIN
SW004 077G 603 AI CJ TACT SWITCH 2PIN
SW006 077G 603 AI CJ TACT SWITCH 2PIN
SW005 077G 603 AI CJ TACT SWITCH 2PIN
SW003 077G 603 AI CJ TACT SWITCH 2PIN

R002 061G0805242 RST CHIPR 2.4 KOHM +-5% 1/8W
R005 061G0805242 RST CHIPR 2.4 KOHM +-5% 1/8W
R004 061G0805432 RST CHIPR 4.3 KOHM +-5% 1/8W
R001 061G0805432 RST CHIPR 4.3 KOHM +-5% 1/8W
R003 061G0805911 RST CHIPR 910 OHM +-5% 1/8W
R006 061G0805911 RST CHIPR 910 OHM +-5% 1/8W

J002 061G1206000 RST CHIP MAX 0R05 1/4W

J001 061G1206000 RST CHIP MAX 0R05 1/4W
E750 750GLM216H1132M0PH PANEL M216H1-L01 C1 NB CMO
E750 750GLM216H1132N000 PANEL M216H1-L01 C1 NB CMO

FQ106 A34G1082AFLA1B0101 BEZEL 21.6 CMO
FQ205 705GQ9CS002 CUSHION ASSY CMO
FQ002 756GQ8CB PH005 SCALER BOARD(CBPCRNDPHQ1) CMO

U402 100GPNMC000NT1 MCU ASSY(056G1133713) CMO

FQ301 089G414A15N CX POWER CORD

E750 750GLU215H1013M0PH PANEL M215HW01 V000 XM AUO
E750 750GLU215H1013N000 PANEL M215HW01 V00 XM AUO
E750 750GLU215H1014M0PH PANEL M215HW01 V000 SH AUO
E750 750GLU215H1014N000 PANEL M215HW01 V000 SH AUO
E750 750GLU215H1023M0PH PANEL M215HW01 V00A XM AUO
E750 750GLU215H1023N000 PANEL M215HW01 V00A XM AUO
E750 750GLU215H1024M0PH PANEL M215HW01 V00A SH AUO
E750 750GLU215H1024N000 PANEL M215HW01 V00A SH AUO

FQ205 705GQ9CS153 CUSHION ASSY

AUO

V000/A

FQ003 PWPC8B41MQCW POWER BOARD ASSY

AUO

V000/A

V00G/H/J

& CMO

CN804 033G8021 2E F WAFER
CN802 033G8021 2E F WAFER
CN802 033G8021 2E XY CONNECTOR
CN804 033G8021 2E XY CONNECTOR

C819 065G 3J6806ET CAP CER 68PF J 3KV SL
C820 065G 3J6806ET CAP CER 68PF J 3KV SL
C821 065G 3J6806ET CAP CER 68PF J 3KV SL
C822 065G 3J6806ET CAP CER 68PF J 3KV SL

L801 073G 174 35 HA IND FILTER 200mH+-25% DADON
L802 073G 174 35 HA IND FILTER 200mH+-25% DADON
L802 073G 174 35DNA FILTER 200mH±25%
L801 073G 174 35DNA FILTER 200mH±25%
L801 S73G17435VA Transformer ASSY

L802 S73G17435VA Transformer ASSY
R844 061G0603103 RST CHIPR 10 KOHM +-5% 1/10W
R843 061G0603103 RST CHIPR 10 KOHM +-5% 1/10W
R842 061G0603103 RST CHIPR 10 KOHM +-5% 1/10W
R845 061G0603103 RST CHIPR 10 KOHM +-5% 1/10W
R838 061G0603105 RST CHIPR 1M OHM +-5% 1/10W
R841 061G0603105 RST CHIPR 1M OHM +-5% 1/10W
R839 061G0603105 RST CHIPR 1M OHM +-5% 1/10W
R840 061G08051004FT RST CHIP R 1 MOHM +-1% 1/8W
R840 061G08051004FY RST CHIPR 1 MOHM +-1% 1/8W YAGEO

RJ809 061G1206000 RST CHIP MAX 0R05 1/4W
RJ812 061G1206000 RST CHIP MAX 0R05 1/4W

D807 093G 64 42 PP BAV70 SOT-23
D808 093G 64 42 PP BAV70 SOT-23
D807 093G 64 42 L DIODE LBAV70LT1G SOT-23 LRC
D808 093G 64 42 L DIODE LBAV70LT1G SOT-23 LRC
D807 093G 64S 6 SMT D-BAV70-7-F SOT-23
D808 093G 64S 6 SMT D-BAV70-7-F SOT-23

72

Meridian 1

FQ002 756GQ9CB PH064 00 SCALER BOARD(CBPCRNDPHQ1)

AUO

V000/A

U402 100GPNAI001NT1 MCU ASSY(056G1133713)

AUO

V000/A

E750 750GLU215H1043M0PH PANEL M215HW01 V00G XM AUO
E750 750GLU215H1043N000 PANEL M215HW01 V00G XM AUO
E750 750GLU215H1053M0PH PANEL M215HW01 V00H XM AUO
E750 750GLU215H1053N000 PANEL M215HW01 V00H XM AUO
E750 750GLU215H1063M0PH PANEL M215HW01 V00J XM AUO
E750 750GLU215H1063N000 PANEL M215HW01 V00J XM AUO

FQ002 756GQ9CB PH065 00 SCALER BOARD ASSY(CBPCRNDPHQ1) V00G/H/J

U402 100GPNAI000NT1 PHILIPS 220E1 V00G/H/J

E08903 089G1748GAA AC SIGNAL CABLE DVI GREATLAND

FQ301 089G414A15N IS POWER

E750 750GLM216H1122M0PH LCD M216H1-L01 C1(GC) NB CMO

E750 750GLM216H1122N000 PANEL M216H1-L01 C1(GC)NB CMO
FQ124 A15G0475401201 MAINFRAME
FQ205 Q44GC085101 EPS
FQ205 Q44GC085201 EPS
FQ201 Q40G 22N813 5D RATING LABEL

CN804 033G8021 2E F CONNECTOR
CN803 033G8021 2E F CONNECTOR
CN802 033G8021 2E F CONNECTOR
CN801 033G8021 2E F CONNECTOR

IC902 056G 139 3A PC123Y22FZOF SHARP

C908 063G 10747410V NO-SUGGEST 0.47UF 275VAC ARCO
C908 063G107K474 6S 0.47UF +-10%
C908 063G107K474 US NO-SUGGEST 0.47uF +-10%
C902 065G305M1022BP CAP Y2 1000PF M 250VAC
C903 065G305M1022BP CAP Y2 1000PF M 250VAC
C900 065G306M3322BP Y1 CAP 3300PF M 250VAC
C922 067G215V471 3H CAP L105C 470UF M 16V
C907 067G315Z10115K EC 100UF 20% 450V 18*40

L801 073G 174 35 HA COMMON FILTER CHOKE 200mH+-25%

L802 073G 174 35 HA COMMON FILTER CHOKE 200mH+-25%

L802 073G 174 35DNA COMMON FILTER CHOKE 200mH¡À25%

L801 073G 174 35DNA COMMON FILTER CHOKE 200mH¡À25%

L905 073G 253 91 H IND CHOKE 3.5uH+-10% DADONG

L906 073G 253 91 H IND CHOKE 3.5uH+-10% DADONG

CN901 087G 501 32 S AC SOCKET ST-01CP-BCE-R

BD901 093G 50460502 BRIDGE KBP206G C2

L802 S73G17435VA TRANSFORMER ASSY

L801 S73G17435VA TRANSFORMER ASSY

Q806 057G 763526 FET APM4548AKC 30V/7.4A -30V/-5.6A Anpec

Q805 057G 763526 FET APM4548AKC 30V/7.4A -30V/-5.6A Anpec
R842 061G0603103 JF RST CHIPR 10K OHM +-5% 1/10W FENGHUA
R843 061G0603103 JF RST CHIPR 10K OHM +-5% 1/10W FENGHUA
R844 061G0603103 JF RST CHIPR 10K OHM +-5% 1/10W FENGHUA
R845 061G0603103 JF RST CHIPR 10K OHM +-5% 1/10W FENGHUA
R807 061G0603103 JF RST CHIPR 10K OHM +-5% 1/10W FENGHUA
R807 061G0603103 JI TEST ONLY RST 0603 10K 5% 1/16W TA-I
R844 061G0603103 JI TEST ONLY RST 0603 10K 5% 1/16W TA-I
R845 061G0603103 JI TEST ONLY RST 0603 10K 5% 1/16W TA-I
R842 061G0603103 JI TEST ONLY RST 0603 10K 5% 1/16W TA-I
R843 061G0603103 JI TEST ONLY RST 0603 10K 5% 1/16W TA-I
R806 061G0603104 JI TEST ONLY RST 0603 100K 5% 1/16W TA-I
R813 061G0603104 JI TEST ONLY RST 0603 100K 5% 1/16W TA-I
R836 061G0603563 Y NO-SUGGEST RST CHIPR 56K +-5% 1/10W Y
R837 061G0603752 JI TEST ONLY RST 0603 7.5K 5% 1/16W TA-I
R925 061G06039101FI TEST ONLY RST 0603 9.1K 1% 1/10W TA-I
R801 061G08051002FY RST CHIP 10K 1/8W 1%
R812 061G08051003FY RST CHIP 100K 1/8W 1%
R840 061G08051004FY RST CHIP 1M 1/8W 1%
R919 061G08051500FT RST CHIPR 150OHM +-1% 1/8W TZAIYUAN
R917 061G1206100 JT RST CHIPR 10 OHM +-5% 1/4W TZAI YUAN
R930 061G1206101 NO-SUGGEST RST CHIPR 100 OHM +-5% 1/4W
R929 061G1206101 NO-SUGGEST RST CHIPR 100 OHM +-5% 1/4W
R912 061G1206101 NO-SUGGEST RST CHIPR 100 OHM +-5% 1/4W
R910 061G1206101 NO-SUGGEST RST CHIPR 100 OHM +-5% 1/4W
R909 061G1206101 NO-SUGGEST RST CHIPR 100 OHM +-5% 1/4W
R903 061G1206101 NO-SUGGEST RST CHIPR 100 OHM +-5% 1/4W
R908 061G1206103 NO-SUGGEST RST CHIPR 10 KOHM +-5% 1/4W
R923 061G1206221 NO-SUGGEST RST CHIPR 220 OHM +-5% 1/4W
R913 061G1206519 JI RST 5.1 OHM 5% 1/4W TA-I
R913 061G1206519 JT RST CHIPR 5.1 OHM +-5% 1/4W TZAI YUAN
R902 061G1206684 NO-SUGGEST RST CHIPR 680 KOHM +-5% 1/4W
R901 061G1206684 NO-SUGGEST RST CHIPR 680 KOHM +-5% 1/4W
R900 061G1206684 NO-SUGGEST RST CHIPR 680 KOHM +-5% 1/4W
C814 065G060322131J A CAP CHIP 0603 220PF J 50V NPO
C805 065G060322332K Y tpv CHIP 0603 22N 50V X7R +/-10%
C807 065G060333232K F CAP CHIP 0603 3.3NF K 50V X7R
C808 065G060333332K A CAP CHIP 0603 33nF K 50V X7R
C914 065G060347131J Y CAP CHIP 0603 470P 50V NPO +/-5%
C915 065G080510332K F CAP 0805 10NF K 50V X7R

C811 065G080510432K A CAP CHIP 0805 0.1UF K 50V X7R

C815 065G080510432K A CAP CHIP 0805 0.1UF K 50V X7R
C912 065G080510432K A CAP CHIP 0805 0.1UF K 50V X7R

74

Meridian 1

D803 093G 6433S switching diode BAV99
R820 061G0603100 Y NO-SUGGEST RST CHIPR 10 OHM +-5% 1/10W Y
R821 061G0603100 Y NO-SUGGEST RST CHIPR 10 OHM +-5% 1/10W Y
C818 065G0805155A2K T NO-SUGGEST 0805 1.5uF K 10V X7R
C818 065G0805155A2K 3 NO-SUGGEST 0805 1.5UF K 10V X7R
R837 061G0603752 JT RST CHIP 7K5 1/10W 5% TZAI YUAN
R925 061G06039101FT RST CHIP 9K1 1/10W 1%
R917 061G1206100 JI RST 10 OHM 5% 1/4W TA-I
R806 061G0603104 JT RST CHIP 100K 1/10W 5% TZAI YUAN
R813 061G0603104 JT RST CHIP 100K 1/10W 5% TZAI YUAN
Q901 057G 667 21 NO-SUGGEST STP10NK70ZFP
Q904 057G 530503 T 2SD1207T
R906 061G152M10452T NO-SUGGEST RST MOFR 100KOHM +-5% 2WS

F902 084G 56 4W FUSE 4A 250V

F901 084G 56 4W FUSE 4A 250V

D904 093G 6038T52T FR103 AO
D801 093G 6452452T SWITCHING 1N4148-B4006 0.2A 100V DO-35
D907 093G 6452452T SWITCHING 1N4148-B4006 0.2A 100V DO-35

IC903 056G 158 10 T IC AS431AZTR-E1 TO-92 BY AAC

FQ002 756GQACB PH060 00 SCALER BOARD ASSY(CBPCRNDPHQ1)

U402 100GPNMI000NT1 MCU ASSY(056G1133713)
CN701 033G3802 9 WAFER 2.0MM 9P
CN101 088G 35315F HX NO-SUGGEST NO-Suggest
CN102 088G 35424F C DVI 24PIN CONN F attached Screw
CN102 088G 35424F N NO-SUGGEST DVI 24PIN CONN F WITH SCREW

X401 093G 22 51 H NO-SUGGEST CRYSTAL 12MHZ/20PF/49US
C305 067G 3151014KB EC LOW ESR 100UF M 25V 6.3*11mm
C704 067G 3151014KB EC LOW ESR 100UF M 25V 6.3*11mm
C706 067G 3151014KB EC LOW ESR 100UF M 25V 6.3*11mm
C707 067G 3151014KB EC LOW ESR 100UF M 25V 6.3*11mm
U107 056G 662502 IC ESD AZC199-04S.R7G SOT23-6L
Q301 057G 763 1 AO3401 SOT23 BY AOS
R472 061G0402000 JI TEST ONLY RST 0402 0.05R MAX 1/16W TA-I
R471 061G0402000 JI TEST ONLY RST 0402 0.05R MAX 1/16W TA-I
R471 061G0402000 JT RST CHIPR MAX0R05 1/16W TZAI YUAN
R472 061G0402000 JT RST CHIPR MAX0R05 1/16W TZAI YUAN
R462 061G0402105 JI EST ONLY RST 0402 1M 5% 1/16W TA-I
R462 061G0402105 JY RST CHIPR 1000KOHM 1/16W YAGEO
R444 061G04023901FI TEST ONLY RST 0402 3.9K 1% 1/16W TA-I
R443 061G04023901FI TEST ONLY RST 0402 3.9K 1% 1/16W TA-I
R401 061G0402470 0F NO-SUGGEST RST CHIPR 0402 470 OHM +-1% 1

R110 061G0402471 JI TEST ONLY RST 0402 470R 5% 1/16W TA-I
R304 061G0402473 JI TEST ONLY RST 0402 47K 5% 1/16W TA-I

R307 061G0402473 JI TEST ONLY RST 0402 47K 5% 1/16W TA-I
R102 061G0603101 JI TEST ONLY RST 0603 100R 5% 1/16W TA-I

FB407 071G 56V301 B CHIP BEAD 0805 300OHM BULLWILL
FB406 071G 56V301 B CHIP BEAD 0805 300OHM BULLWILL
FB401 071G 56V301 B CHIP BEAD 0805 300OHM BULLWILL
FB403 071G 56V301 B CHIP BEAD 0805 300OHM BULLWILL
FB404 071G 56V301 B CHIP BEAD 0805 300OHM BULLWILL

R443 061G04023901FF RST CHIPR 3.9KOHM +-1% 1/16W FENGHUA
R444 061G04023901FF RST CHIPR 3.9KOHM +-1% 1/16W FENGHUA

R110 061G0402471 JT RST CHIP 470R 1/16W 5% TZAI YUAN
R304 061G0402473 JF RST CHIPR 47KOHM +-5% 1/16W FENGHUA
R307 061G0402473 JF RST CHIPR 47KOHM +-5% 1/16W FENGHUA
R102 061G0603101 JT RST CHIP 100R 1/10W 5% TZAI YUAN
D001 081G 12 1F GP LED 3¦µ »ÆÂÌË«É« GP32032M/G307-ZY-50-C

SW003 077G603S AI CJ TACT SWITCH AI 2PIN SEALED
SW005 077G603S AI CJ TACT SWITCH AI 2PIN SEALED
SW006 077G603S AI CJ TACT SWITCH AI 2PIN SEALED
SW004 077G603S AI CJ TACT SWITCH AI 2PIN SEALED
SW002 077G603S AI CJ TACT SWITCH AI 2PIN SEALED
SW001 077G603S AI CJ TACT SWITCH AI 2PIN SEALED
SW006 077G603S AI HJ TACT SWITCH AI 2PIN SEALED
SW005 077G603S AI HJ TACT SWITCH AI 2PIN SEALED
SW003 077G603S AI HJ TACT SWITCH AI 2PIN SEALED
SW004 077G603S AI HJ TACT SWITCH AI 2PIN SEALED
SW002 077G603S AI HJ TACT SWITCH AI 2PIN SEALED
SW001 077G603S AI HJ TACT SWITCH AI 2PIN SEALED

Service Kit

Description Part No. Philips 12NC Picture

DDC KIT 715G2005C2 996500043197

NOVATEK ISP KIT 715LT035A 996500043198

76

Meridian 1

17. Different Parts List

Diversity of 220E1SB/00 compared with 220E1SB/69

220E1SB/00 220E1SB/69

Location PCM Codes Description Philips 12NC PCM Codes Description

FQ301 089G404A15N IS POWER CORD 996510019911 089G410A15N IS

POWER CORD
WALL-OUT FOR UK

FQ105 A34G0897AFL 2B0100 REAR COVER 21.5″ 996520036099 A34G0897AFL 3B0100 REAR COVER 21.5″

FQ202 Q44GC085813 3D 21.6 LCD CARTON Q44GC085813 2D 21.6 LCD CARTON

FQ002 756GQ8CB PH007

SCALER BOARD
ASSY(CBPCRNDPHQ2) for CMO

756GQ8CB PH005

SCALER BOARD
ASSY(CBPCRNDPHQ1) for CMO

U402 100GPNMC001NT1 MCU ASSY(056G1133713) 100GPNMC000NT1 MCU ASSY(056G1133713)

FQ002 756GQ9CB PH071 00

SCALER BOARD
ASSY(CBPCRNDPHQ2) for V00H/G/J

756GQ9CB PH065 00

SCALER BOARD
ASSY(CBPCRNDPHQ2) for V00H/G/J

U402 100GPNAI004NT1 MCU ASSY(056G1133713) 100GPNAI000NT1 MCU ASSY(056G1133713)

E750 750GLU215H1533M0PH PANEL M215HW01 V50B XM AUO

E750 750GLU215H1533N000 PANEL M215HW01 V50B XM AUO

E750 750GLU215H1543M0PH PANEL M215HW01 V50C XM AUO

E750 750GLU215H1543N000 PANEL M215HW01 V50C XM AUO

FQ002 756GQ9CB PH073 00

SCALER BOARD
ASSY(CBPCRNDPHQ2)

U402 100GPNAI005NT1 MCU ASSY(056G1133713)

E750 750GLU215H1013N000 PANEL M215HW01 V00 XM AUO

E750 750GLU215H1013M0PH PANEL M215HW01 V000 XM AUO

E750 750GLU215H1014M0PH PANEL M215HW01 V000 SH AUO

E750 750GLU215H1014N000 PANEL M215HW01 V000 SH AUO

E750 750GLU215H1023M0PH PANEL M215HW01 V00A XM AUO

E750 750GLU215H1023N000 PANEL M215HW01 V00A XM AUO

77

Meridian 1

E750 750GLU215H1024M0PH PANEL M215HW01 V00A SH AUO

E750 750GLU215H1024N000 PANEL M215HW01 V00A SH AUO

FQ002 756GQ9CB PH072 00

SCALER BOARD
ASSY(CBPCRNDPHQ2)

U402 100GPNAI003NT1 MCU ASSY(056G1133713)

E750 750GLS215HT112M0PH PANEL LTM215HT01 C01 SZ SEC

E750 750GLS215HT112N000 PANEL LTM215HT01 C01 SZ SEC

E750 750GLS215HT122M0PH PANEL LTM215HT01 C02 SZ SEC

E750 750GLS215HT122N000 PANEL LTM215HT01 C02 SZ SEC

FQ002 756GQ9CB PH043

SCALER BOARD
ASSY(CBPCRNDPHQ2)

U402 100GPNSI001NT1 MCU ASSY(056G1133713)

FQ003 PWPC9B41AQYO

POWER BOARD ASSY for AUO
V50B/C & SEC

E750 750GLM216H1122M0PH LCD M216H1-L01 C1(GC) NB CMO

E750 750GLM216H1122N000 PANEL M216H1-L01 C1(GC)NB CMO

FQ105 A34G0897AFL 3B0100 REAR COVER 21.5

FQ106 A34G1082AFLA1B0101 BEZEL 21.6

FQ002 756GQACB PH060 00

SCALER BOARD
ASSY(CBPCRNDPHQ1)

U402 100GPNMI000NT1 MCU ASSY(056G1133713)

E750 750GLM216H1132M0PH PANEL M216H1-L01 C1 NB CMO

E750 750GLM216H1132N000 PANEL M216H1-L01 C1 NB CMO

FQ002 756GQ8CB PH005

SCALER BOARD
ASSY(CBPCRNDPHQ1)

U402 100GPNMC000NT1 MCU ASSY(056G1133713)

78

Meridian 1

Diversity of 220E1SB/05 compared with 220E1SB/69

220E1SB/05 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

FQ105 A34G0897AFL 2B0100 REAR COVER 21.5″ 996520036099 A34G0897AFL 3B0100 REAR COVER 21.5″

FQ202 Q44GC085813 3D 21.6 LCD CARTON Q44GC085813 2D 21.6 LCD CARTON

FQ002 756GQ8CB PH007

SCALER BOARD ASSY
(CBPCRNDPHQ2) for CMO

996520037004 756GQ8CB PH005

SCALER BOARD ASSY
(CBPCRNDPHQ1) for CMO

U402 100GPNMC001NT1 MCU ASSY(056G1133713) 996520037005 100GPNMC000NT1 MCU ASSY(056G1133713)

Diversity of 220E1SB/27 compared with 220E1SB/69

220E1SB/27 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

FQ301 089G402A15N IS POWER CORD 996510019911 089G410A15N IS POWER CORD WALL-OUT FOR UK

Diversity of 220E1SB/62 compared with 220E1SB/69

220E1SB/62 220E1SB/69

Location PCM Codes Description Philips 12NC PCM Codes Description

FQ301 089G404A15N IS POWER CORD 089G410A15N IS POWER CORD WALL-OUT FOR UK

FQ105 A34G0897AFL 2B0100 REAR COVER 21.5″ 996520036099 A34G0897AFL 3B0100 REAR COVER 21.5″

FQ202 Q44GC085813 3D 21.6 LCD CARTON Q44GC085813 2D 21.6 LCD CARTON

FQ002 756GQ8CB PH007

SCALER BOARD ASSY
(CBPCRNDPHQ2) for CMO

996520037004 756GQ8CB PH005

SCALER BOARD ASSY
(CBPCRNDPHQ1) for CMO

U402 100GPNMC001NT1 MCU ASSY(056G1133713) 996520037005 100GPNMC000NT1 MCU ASSY(056G1133713)

79

Meridian 1

FQ002 756GQ9CB PH071 00

SCALER BOARD ASSY
(CBPCRNDPHQ2) for V00H/G/J

756GQ9CB PH065 00

SCALER BOARD ASSY
(CBPCRNDPHQ1) for V00H/G/J

U402 100GPNAI004NT1 MCU ASSY(056G1133713) 100GPNAI000NT1 MCU ASSY(056G1133713)

FQ002 756GQ9CB PH072 00

SCALER BOARD ASSY
(CBPCRNDPHQ2) for V000/A

U402 100GPNAI003NT1

MCU ASSY（056G1133713）

Diversity of 220E1SB/75 compared with 220E1SB/69

220E1SB/75 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

FQ301 996510016841 089G412A15NIS3 POWER CORD 996510019911 089G410A15N IS POWER CORD WALL-OUT FOR UK

Diversity of 220E1SB/94 compared with 220E1SB/69

220E1SB/94 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

FQ301 996510015866 089G417A15N IS POWER CORD 996510019911 089G410A15N IS POWER CORD WALL-OUT FOR UK

Diversity of 220E1SB/96 compared with 220E1SB/69

220E1SB/96 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

FQ301 996520037009 089G420A15N IS POWER CORD 996510019911 089G410A15N IS POWER CORD WALL-OUT FOR UK

FQ105 996520037011 A34G0897AFL 2B0100 REAR COVER 21.5″ 996520036099 A34G0897AFL 3B0100 REAR COVER 21.5″

FQ202 996520036087 Q44GC085813 3D 21.6 LCD CARTON Q44GC085813 2D 21.6 LCD CARTON

80

Meridian 1

FQ002 996520037012 756GQ8CB PH007

SCALER BOARD ASSY
(CBPCRNDPHQ2) for CMO

996520037004 756GQ8CB PH005

SCALER BOARD ASSY
(CBPCRNDPHQ1) for CMO

U402 996520037013 100GPNMC001NT1 MCU ASSY(056G1133713) 996520037005 100GPNMC000NT1 MCU ASSY(056G1133713)

Diversity of 220E1SB/97 compared with 220E1SB/69

220E1SB/97 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

FQ301 996510015663 089G404A15N IS POWER CORD 996510019911 089G410A15N IS POWER CORD WALL-OUT FOR UK

Diversity of 220E1SB/78 compared with 220E1SB/69

220E1SB/78 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

Diversity of 220E1SB1/01 compared with 220E1SB/69

220E1SB1/01 220E1SB/69

Location PCM Codes Description Location PCM Codes Description

FQ301 089G404A15N IS AC POWER CORD 1500MM Europe Reg. FQ301 089G410A15N IS POWER CORD WALL-OUT FOR UK

81

Meridian 1

Diversity of 220E1SB1/62 compared with 220E1SB/69

220E1SB1/62 220E1SB/69

Location PCM Codes Description Location PCM Codes Description

FQ301 089G404A15N IS AC POWER CORD 1500MM Europe Reg. FQ301 089G410A15N IS POWER CORD WALL-OUT FOR UK

FQ002 756GQ8CB PH007 SCALER BOARD ASSY(CBPCRNDPHQ2) FQ002 756GQ8CB PH005 SCALER BOARD ASSY(CBPCRNDPHQ1)

U402 100GPNMC001NT1 MCU ASSY(056G1133713) U402 100GPNMC000NT1 MCU ASSY(056G1133713)

FQ105 A34G0897AFL 2B0100 REAR COVER 21.5 FQ105 A34G0897AFL 3B0100 REAR COVER 21.5

FQ202 Q44GC085813 3D 21.6 LCD CARTON FQ202 Q44GC085813 2D 21.6 LCD CARTON

FQ002 756GQ9CB PH071 00 SCALER BOARD ASSY(CBPCRNDPHQ2) FQ002 756GQ9CB PH065 00 SCALER BOARD ASSY(CBPCRNDPHQ1)

U402 100GPNAI004NT1 MCU ASSY(056G1133713) U402 100GPNAI000NT1 MCU ASSY(056G1133713)

Diversity of 220E1SB1/94 compared with 220E1SB/69

220E1SB1/94 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

Diversity of 220E1SB1/97 compared with 220E1SB/69

220E1SB1/97 220E1SB/69

Location Philips 12NC PCM Codes Description Philips 12NC PCM Codes Description

82

Meridian 1

18. General Product Specification

TABLE OF CONTENTS

1. FOREWORD

2. PRODUCT PROFILE

2.1 LCD

2.2 SCANNING FREQUENCIES

2.3 AMBIENT TEMPERATURE: 0℃-40℃

3. ELECTRICAL CHARACTERISTICS

3.1 INTERFACE SIGNALS

3.2 INTERFACE

3.3 TIMING REQUIREMENT

3.4 HORIZONTAL SCANNING

3.5 VERTICAL SCANNING

3.6 POWER INPUT CONNECTION

3.7 POWER MANAGEMENT (SUPPORT TO INPUT)

3.8 VGA DISPLAY IDENTIFICATION

3.9 DDC/CI SUPPORT

3.10 DATA FOR EDID & INF FILE

3.11 HOT-KEY DEFINITION

4. VISUAL CHARACTERISTICS

4.1 TEST CONDITIONS

4.2 BRIGHTNESS

4.3 IMAGE SIZE

4.4 BRIGHTNESS UNIFORMITY

4.5 CHECK CROSS TALK(S)

4.6 WHITE COLOR ADJUSTMENT

5. MECHANICAL CHARACTERISTICS

5.1 COSMETIC

5.2 MECHANICAL DATA FILES

5.3 LOCATION OF PHILIPS LOGO

5.4 GAP BETWEEN PANEL AND FRONT BEZEL

5.5 LOCATION OF CONTROL ICONS

5.6 COLOR FOR RESIN/PAINT

5.7 RESINS

5.8 IF PAINT IS USED

5.9 PLASTIC MOLD TOOLING

5.10 PLASTICS FLAMMABILITY

5.11 TEXTURE/GLOSSING OF HOUSING

5.12 TILT AND SWIVEL BASE

5.13 KENNSINGTON LOCK

5.14 LABEL

5.15 PRODUCT DIMENSION/WEIGHT (REFER TO PHILIPS APPROVED SHT 191)

5.16 TRANSPORTATION

83

Meridian 1

5.17 PALLET/CONTAINER LOADING

6. ENVIRONMENTAL CHARACTERISTICS

6.1 SUSCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT

6.2 TRANSPORTATION TESTS

6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT

6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT

7. RELIABILITY

7.1 MEAN TIME BETWEEN FAILURES

8. QUALITY ASSURANCE REQUIREMENTS

8.1 ACCEPTANCE TEST

9. PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLITY

10. REGULATORY COMPLIANCE

10.1 WORLDWIDE REGULATORY

10.2 EMC REQUIREMENTS

10.3 ROHS

10.4 WEEE

10.5 ONGOING REGULATORY

84

Meridian 1

1. FOREWORD

This specification describes a 21.5″ FHD multi-scan color TFT LCD monitor with maximum resolution up to 1920 x
1080/75Hz non-interlaced.
All optical characteristics (including White-D, Brightness and so on) are determined according to panel specification
after warming up approximate 30 minutes that brightness stability is optimal, and follow strictly after panel
specification.

2. PRODUCT PROFILE

This display monitor unit is a color display monitor enclosed in Philips styling cabinet which has an integrated tilt
base.

LCD

Priority: 1. CMO M216H1-L01
Type: TN
Suppliers to offer the panel specification.
Panel incoming specification: Follow Philips’ specification.

CMO M216H1-L01
Type NR. : M216H1-L01
Resolution :1920 x 1080 (FHD)
Outside dimensions :499.5 (H) x 292.6 (V) x 17.0 (D)mm (Typ.)
Pitch (mm) :0.248 mm x 0.248 mm
Color pixel arragnement : 1920 horizontal By 1080 vertical Pixels. RGB stripe arrangement
Display surface :Hard coating (3H), Anti-glare treatment of the front polarizer
Color depth :16.7M colors
Backlight :4CCFL
Active area (W xH) :477.50 (H) x 268.59 (V)
View angle (CR>10) : R/L 170(Typ.), U/D 160(Typ.)
Contrast ratio :1000:1 (Typ.) 700:1 (Min)
White Luminance : 300cd/m2(Typ) 250(Min)
Color gamut :>=72%
Gate IC :
Source IC :
Response time :5ms (Typ.) 8ms (Max)
Vertical frequency range :58.1~85Hz

Scanning frequencies

Hor. : 30 – 80 KHz
Ver. : 56 - 76 Hz
Video dot rate : <205 MHz (analog), EDID: 170MHz
<165 MHz (digital), EDID: 170MHz
Power input

: 90-264 V AC, 50/60

±

2 Hz
Power consumption : 40W (typ.), < 42 W maximum
Functions:

85

Meridian 1

（1）D-SUB analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level, SOG sync

（2）DVI digital Panel Link TMDS inputs

Ambient temperature: 0 °C - 40 °C

3. ELECTRICAL CHARACTERISTERS

Interface signals

(1) D-sub analog
Input signal :Video, Hsync, Vsync
Video :0.7 Vp-p, input impedance, 75 ohm @DC
Sync :Separate sync TTL level, input impedance 2.2K ohm terminate

:Hsync Positive/Negative
:Vsync Positive/Negative
:Composite sync TTL level, input impedance 2.2k ohm terminate
(Positive/Negative)

Sync on green video : 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)

(2) DVI-D Digital
Input signal :Single TMDS link (Three channels: RX0-/+, RX1-/+, RX2-/+)

Interface

D-SUB Cable

Length :1.5m +/- 50mm
Fix with monitor when packing with transplant pin protective cover.
Connector type :D-sub male with DDC2B pin assignments

Blue connector thumb-operated jack screws

Pin assignments

PIN No. SIGNAL

1 Red
2 Green/ SOG
3 Blue
4 Sense (GND)
5 Cable Detect (GND)
6 Red GND
7 Green GND
8 Blue GND

9 DDC +3.3V or +5V
10 Logic GND
11 Sense (GND)
12 Bi-directional data
13 H/H+V sync
14 V-sync
15 Data clock

DVI Cable

86

Meridian 1

The input signals are applied to the display through DVI-D cable.

Length :1.8m +/- 50mm
Connector type :D-VI-D male with DDC-2B pin assignments

White connector thumb-operated jack screws with transplant pin protective cover.

Pin assignments

PIN No.

Description

1

T.M.D.S. data2-

2

T.M.D.S. data2+

3

T.M.D.S. data2 shield

4

No Connect

5

No Connect

6

DDC clock

7

DDC data

8

No Connect

9

T.M.D.S. data1-

10

T.M.D.S. data1+

11

T.M.D.S. data1 shield

12

No Connect

13

No Connect

14

+5V Power

15

Ground (for +5V)

16

Hot plug detect

17

T.M.D.S. data0-

18

T.M.D.S. data0+

19

T.M.D.S. data0 shield

20

No Connect

21

No Connect

22

T.M.D.S clock shield

23

T.M.D.S. clock+

24

T.M.D.S. clock-

Timing requirement

Factory Preset mode definition:

1. Perfect FOS while presenting all required timings

2. Required timing need to be specified in User’s Manual

User mode

1. Can be showed (not over scalar or panel spec.)

2. It needs to reserve the 22 timings space in memory size.

Mode storing capacity

Factory preset modes : 11
User modes :39

Note:

1. Screen displays perfect picture at factory-preset modes

2. Screen displays visible picture with OSD warning when input modes are the 22 reset mode

87

Meridian 1

Factory preset modes

• Factory modes and preset modes are defined in the enclosed timing table file

220E1 1920 1080

Timming Table-0810

2

• Video timing mode (internal firmware support)
60Hz: 480i/480p/720p/1080i/1080p
50Hz: 576i/576p/720p/1080i/1080p

Software control functions via OSD/Control adjustment functions

Please refer to following Hudson 9 OSD definitions, if any deviation, there refer to PVT exit sample.

ITEM

1 OSD DEFINITIONS

PHILIPS 220E1 OSD

Definition-081201.xl

s

Reset -
No: Exit
Yes: Auto adjustment for displaying
timing mode and recall factory preset

2 OSD LANGUAGES

H8 OSD translation ­20070425 - Final.xls

H9 new item

translation _ 2008041

8 LANGUAGES

3 OSD TREE

PHILIPS 220E1 OSD

Tree-081023.xls

4 POWER ON LOGO

1920x1080_new.

zip

Power On Logo: Power On Æ
Show up Philips logo 3 seconds Æ
Change to input signal.

This picture is reference only. The
official drawing will send out by PM.

5 AUDIO SELECTION

Stand-alone – On:
Isolate video and audio control input
Stand-alone – Off:
Integrate video and audio control
input
Mute – On: Turn off audio
Mute – Off: Turn on audio

88

Meridian 1

Horizontal scanning

Sync polarity :positive or negative
Scanning frequency :30-83KHz

Vertical scanning

Sync polarity :positive or negative
Scanning frequency :56-76Hz

Power input connection

Power cord length :1.5m
Power cord type :3 leads power cord with protective earth plug

Power management (supplier to input)

The monitor must comply with the Microsoft on Now specification and meet EPA requirement.

Mode HSYNC VSYNC Video Pwr-cons. Indication Rec. time

Power-On On On active

40W Typ.

Green LED --

< 42 W Max.
Power saving Off Off blanked < 0.8W Amber LED < 3 s
DC Power Off N/A < 0.5 W LED Off

VGA Display identification
In accordance with VESA Display Channel Standard Ver.1.0 and DDC 2B capability

DDC/CI support

In accordance with VESA DDC/CI and MCCS ver.2.0

Data for EDID & INF file

Data for EDID & .inf file

1 User visible strings on .inf file

Philips 220E (22inch Wide LCD MONITOR 220E1)

2 Manufacturer ID ( EDID data)

PHL

3

Product ID, "xxxx" 4 codes

MSB(byte 12): C0
LSB (byte 11): 2E

4 maximum resolution

1920x1080

5 Horizontal Frequency Range

30~83 KHz

6 Vertical Frequency Range

56~76Hz

7 Monitor Name (13 characters max.)

Philips 220E

Hot-key definition

HOT KEY.xls

Any deviation between document and sample, please refer to Philips approved sample.

Smart contrast (Dynamic contrast ratio)

Smart Contrast is a kind of dynamic backlight control.
This function changes panel backlight dynamically according to the frame brightness histogram.
At least the minimum contrast ratio has to be > 8000:1(typ).

89

Meridian 1

4. Visual characteristics

Test conditions

Unless otherwise specified, this specification is defined under the following conditions.
(1) Input signal: As defined in 3.3, 1920*1080

non-interlaced mode (1920*1080@60Hz 148.50MHz), signal sources must

have 75 ohm output impedance
(2) Luminance setting: controls to be set to 300 nits with full screen 100 % duty cycle white signal
(3) Warm up: More than 30 minutes after power on with signal supplied.
(4) Ambient light: 400 -- 600 lux
(5) Ambient temperature:

20 ± 5 °C

Brightness
To follow Panel specification

Image size

Actual display size: Refer to 2.1 LCD PANEL spec.

Brightness uniformity

Set contrast at 100% and turn the brightness to get average above 300 nits at centre of the screen. Apply the Fig 1;
it should comply with the following formula:
B_min

X 100% > 75% (Follow panel spec)
B_max
Where B_max =Maximum brightness

B_min = Minimum brightness

Check Cross talk(s)

Apply Pattern 2. Set contrast and brightness at 100 %. Measure YA. Then output Pattern 3 and measure YB. The
cross talk value:
ABS (YA - YB)

⎯⎯⎯⎯⎯⎯⎯⎯⎯ X 100% < 1.5 %
YA

White Color adjustment

There are three factory preset white color 9300K, 6500 and sRGB align by FGA function.
Apply full gray 64 pattern, with brightness in 100 % position and the contrast control at 50 % position.
The 1931 CIE Chromaticity (color triangle) diagram (x, y) coordinate for the screen center should be:

Product specification

CIE coordinates (x,y)

9300K

x = 0.283 ± 0.02

y = 0.297 ± 0.02

6500K/sRGB

x = 0.313 ± 0.02

y = 0.329 ± 0.02

sRGB

x = 0.313 ± 0.02

y = 0.329 ± 0.02

90

Meridian 1

Production alignment spec.

CIE coordinates (x,y)

9300K

x = 0.283 ± 0.006

y = 0.297 ± 0.006

6500K/sRGB

x = 0.313 ± 0.006

y = 0.329 ± 0.006

sRGB

x = 0.313 ± 0.006

y = 0.329 ± 0.006

Quality Inspection specification:

CIE coordinates (x,y)

9300K

x = 0.283 ± 0.015

y = 0.297 ± 0.015

6500K/sRGB

x = 0.313 ± 0.015

y = 0.329 ± 0.015

sRGB

x = 0.313 ± 0.015

y = 0.329 ± 0.015

* TPV OTS model, but the Perfect Tune function is also apply for this model at the TPV production line.

5. Mechanical characteristics

Cosmetic

Philips ID

Mechanical data files

ProE files required

Location of Philips Logo

Per Philips make-up sheet

Gap between panel and front bezel

< 1.4mm (typ.)

Location of Control Icons

Per Philips Graphic sheet

Color for resin/paint

Per Philips make-up sheet

Resins

• RoHS required

• WEEE required.

• Resin type/selection refers to Project Book Section 7.2 Plastic material.

91

Meridian 1

If paint is used

• RoHS required

• WEEE require

• If new painting type needs to implement, refer to UN-D 1235.

Plastic mold tooling

• Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld lines, gate

marks, ejector marks, etc.). Refer to “TYV61-90007”.

• Painting to cover up cosmetic defects due to molding is strongly discouraged.

• China RoHS mark requested.

Plastics flammability

• All Plastics to be Flame Retardant UL 94-HB.

• Base / Rear to be Flame Retardant UL 94-HB

• All major plastic parts (bezel, back cover) need to be molded from same resin

• Plastic resin type selection should be referred to “plastic-Philips Pool monitor”

Texture/Glossing of housing

• The texture area and texture no should follow Philips make-up sheet.

• The exterior surfaces shall have a uniform texture.

• Philips must approve the mold texturing.

• Detail document for texture refer to “UN-D249”, “UN-D 600”.

• > = 80 gloss units

Tilt and swivel base

• Tilt angle : -5 ° +2/- 0 ° (forward)

+20 °+0/- 2 ° (backward)

• Tilt for left and right:

︱A-B︱≤4.0MM

• Black side and cut side：

1. Visual area

H：｜L-R｜≤1.5mm

V：｜U-D｜≤1.5mm

2. Black side on the left and right is
symmetrical, not cut side.

• Gap between bezel and rear cover 0.4 mm (Typ.)

• Step between bezel and rear cover Left, right and top: ≤0.6mm Bottom and corner: ≤1.1mm

• "Wobble", "Twist", etc (front to back or side to side)

Whole monitor set shall retain stability within a short time after the applied external force disappears.

20NT , 6secs（Max.） back to stable.

R

L

U

D

A

B

92

Meridian 1

Kensington Lock

• Must meet Kensington_slot.spec “TYE-M0004”.

Label

• Carton label should follow Philips requirement.

• Regulatory label follow Philips requirement

• China RoHS label

• Detail document refer to Philips Engineering Reference Book

Product dimension / Weight (Refer to Philips approved SHT 191/SHT560)

• Unit dimension : 439(w)*363(H)*191(D)

• Packed unit dimension: :5700(w)*453(D)*140(H)

• Net weight : 1.9Kg

• Gross weight : 6.3Kg.

Transportation

Transportation standards refer to UAN-D1534/00/01

Transportation packages

Packaging and wrapping shall be sufficient to protect the product against damage or loss during shipment from
the supplier to the destination specified in the purchase order. All packaging materials are subject to test and
evaluation per TPV standard. The cushion material shall be constructed using EPS material.

Transportation Test

• Package test

1. Random Vibration test

2. Drop test

3. Cold Drop test (for design reference)

• Un-package test
Half sine shock test (non operation)

Pallet / Container loading

Transportation standards refer to TYE-M0002, UAN-D1534 and UAW-0309.

• Air shipment -

• Sea container 20'(pallet/slip sheet)

• Sea container 40'(pallet/slip sheet)

• Sea container 40' High Cube (pallet/slip sheet)

• Land 45‘ Truck and Trailer (800X1200mm pallet)

• Land 45‘ Truck and Trailer (1000X1200mm pallet) for UK

•

Truck shipment-

Transportation request for all regions except China/India

A. Air shipment
B. 20’/40’/40’HQ Container loading for WW

Transportation request for China and India

A. Container loading for China and India
B. Truck loading

93

Meridian 1

Transportation request for EU

A. Land 45‘ Truck and Trailer (800X1200mm pallet)
B. Land 45‘ Truck and Trailer (1000X1200mm pallet) for UK

6. Environmental characteristics

The following sections define the interference and susceptibility condition limits that might occur between external
environment and the display device.

Susceptibility of display to external environment

Operating

Temperature : 0 to 40 degree C
Humidity : 20~90% max
Altitude : 0-10000 ft
Air pressure :600-1100 mBAR

Storage

Temperature : -20 to 60 degree C
Humidity : 10~90% max
Altitude : 0-30000 ft
Air pressure : 300-1100 mBAR

Note: Recommend at 5 to 35°C, Humidity less than 60 %. Please also refer to DQE requirements.

Transportation tests

Refer to 5.15.2

Display disturbances from external environment

According to IEC 801-2 for ESD disturbances

Display disturbances to external environment

7. Reliability

7.1 Mean Time between Failures

System MTBF (excluding the LCD panel and CCFL): Refer to 2.1 panel MTBF

8. Quality assurance requirements

8.1 Acceptance test

According to MIL-STD-105D Control II level
AQL: 0.4 (major)

1.5 (minor)

(Please also refer to annual quality agreement) Customer acceptance criteria: UAW0377/00

94

Meridian 1

9. Philips’ Flat Panel Monitors Pixel Defect Policy

Philips’ Flat Panel Monitors Pixel Defect Policy

BRIGHT DOT DEFECTS

ACCEPTABLE LEVEL

Model

220E1

1 lit sub-pixel 3

2 adjacent lit sub-pixels 1

3 adjacent lit sub-pixels (one white pixel) 0

Distance between two bright dot defects* ≧25mm

Bright dot defects within 20 mm circle 0

Total bright dot defects of all type 3

BLACK DOT DEFECTS

ACCEPTABLE LEVEL

Model

220E1

1 dark sub-pixel 5

2 adjacent dark sub-pixels 2

3 adjacent dark sub-pixels (one white pixel) 0

Distance between two black dot defects*

≧15mm

Black dot defects within 20 mm circle* 1

Total black dot defects of all type 5

TOTAL DOT DEFECTS

ACCEPTABLE LEVEL

Model

220E1

Total bright or black dot defects of all type 5

* 1 or 2 adjacent sub-pixel defects = 1 dot defect

95

Meridian 1

Fig 1: Measurement locations of Brightness Uniformity

Fig 2: Cross talk pattern Gray level 46 (64 Gray level)

YA

1/2

1/2

1/6

Fig 3: Cross talk Pattern Center at Gray level 0 (Black)

YB

1/2

1/2

1/6

1/3 1/3

1/3

1/3

1/3

96

Meridian 1

10. REGULATORY COMPLIANCE

Worldwide Regulatory

TYE-A0004 LCD

MNT International

EMC Requirements

Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be
submitted again prior to PVT samples delivery which also has to meet Philips' immunity testing specification.

RoHS

Restriction on the use of certain hazardous substances:
Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Bipheny1 (PBB) and Polybrominated Bipheny1
Ether (PBDE) (flame retardant).

WEEE

Producer (Philips) responsible for retailer takes back schemes and recycling.

--System implemented.

--Collection and recycle targets.

Ongoing Regulatory

There's a possibility that other regulatory certificates will be required during the life of the product. It is the
responsibility of the supplier to provide related documentation.

Meridian 1

97

TELEVISION/MONITOR SAFFTY GUIDELINES FOR THE PROFESSIONAL SERVICE TECHNICIAN

Safety Checks

Fire and Shock Hazard

Implosion

X-radiation

After the original service problem has been corrected,a complete safety check
should be made. Be sure to check over the entire set, not just the areas
where you have worked. Some previous servicer may have left an unsafe
condition,which could be unknowingly passed on to your customer. Be sure
to check all of the following:

1. Be sure all components are positioned in such a way as to avoid the
possibility of adjacent component shorts. This is especially important
on those chassis which are transported to and from the service shop.

2. Never release a repaired unit unless all protective devices such as

insulators, barries, covers, strain reliefs, and other hardware have been
installed in accordance with the original design.

3. Soldering and wiring must be inspected to locate possible cold solder

joints,solder splashes,sharp solder points, frayed leads, pinched leads,

or damaged insulation ( including the ac cord).Be certain to remove

loose solder balls and all other loose foreign particles.

4. Check across-the-line components and other components for physical

evidence of damage or deterioration and replace if necessary. Follow
original layout,lead length, and dress.

5. No lead or component should touch a receiving tube or a resistor rated

at 1 watt or more. Lead tension around protruding metal surfaces or
edges must be avoided.

6. Critical components having special safety characteristics are identified

withansbytheRef.No.inthepartslistandenclosedwithinabrokenline

* (where several critical components are grouped in one area) along with

the safety symbols on the schematic diagrams and/or exploded views.

7. When servicing any unit, always use a separate isolation transformer
for the chassis Failure to use a separate isolation transformer may
expose you to possible shock hazard, and may cause damage to
servicing instruments.

8. Many electronic products use a polarized ac line cord (one wide pin on
the plug.) Defeating this safety feature may create a potential hazard to
the service and the user. Extension cords which do not incorporate the
polarizing feature should never be used.

9. After reassembly of the unit, always perform an leakage test or resistance
test from the line cord to all exposed metal parts of the cabinet. Also check
all metal control shafts(with knobs removed), antenna terminals, handles,
screws, etc. to be sure the unit may be safety operated without danger of
electrical shock.

* Broken line

1. All picture tubes used in current model receivers are equipped with an

integral implosion system. Care should always be used, and safety
glasses worn,whenever handling any picture tube. Avoid scratching or

otherwise damaging the picture tube during installation.

2. Use only replacement tubes specified by the manufacturer.

1. Be sure procedures and instructions to all your service personnel cover

the subject of X-radiation. Potential sources of X-rays in TV receivers are
the picture tube and the high voltage circuits. The basic precaution which
must be exercised is to keep the high voltage at the factory recommended
level.

2. To avoid possible exposure to X-radiation and electrical shock, only the

manufacturer's specified anode connectors must be used.

3. It is essential that the service technician has an accurate HV meter
available at all times. The calibration of this meter should be checked
periodically against a reference standard.

4. When the HV circuitry is operating properly there is no possibility of an x­radiation problem. High voltage should always be kept at the manufacturer's

rated value-no higher - for optimum performance. Every time a color set is

serviced, the brightness should be run up and down while monitoring the
HV with a meter to be certain that the HV is regulated correctly and does
not exceed the specified value. We suggest that you and your technicians
review test procedures so that HV and HV regulation are always checked as

a standard servicing procedure, and the reason for this prudent routine is

clearly understood by everyone. It is important to use an accurate and

reliable HV meter. It is recommended that the HV recorded on each
customer's invoice, which will demonstrate a proper concern for the
customer's safety.

5. When troubleshooting and making test measurements in a receiver with

a problem of excessive high voltage, reduce the line voltage by means of
a Variac to bring the HV into acceptable limits while troubleshooting. Do
not operate the chassis longer than necessary to locate the cause of the
excessive HV.

:

:

WARNING OFF

SERVICE NOTE

Before removing the CRT anode cap, turn the unit and short the HIGH VOLTAGE to the CRT DAG ground.

The CRT DAG is not at chassis ground.

6. New picture tubes are specifically designed to withstand higher operathng
voltages without creating undesirable X-radiation. It is strongly
recommended that any shop test fixture which is to be used with the new
higher voltage chassis be equipped with one of the new type tubes
designed for this service. Addition of a permanently connected HV meter
to the shop test fixture is advisable. The CRT types used in these new

sets should never be replaced with any other types, as this may result in

excessive X-radiation.

7. It is essential to use the specified picture tube to avoid a possible X-diation
problem.

8. Most TV receivers contain some type of emergency "Hold Down" circuit to
prevent HV from rising to excessive levels in the presence of a failure
mode. These various circuits should be understood by all technicians
servicing them, especially since many hold down circuits are inoperative
as long as the receiver performs normally.

1. Unplug the ac line cord and connect a jumper between the two prongs of

the plug.

2. Turn on the power switch.

3. Measure the resistance value between the jumpered ac plug and all

exposed cabinet parts of the receiver, such as screw heads, antennas,
and control shafts. When the exposed metallic part has a return path to
the chassis, the reading should be between 1 megohm and 5.2 megohms.
When the exposed metal does not have a return path to the chassis, the
reading must be infinity. Remove the jumper from the ac line cord.

1. Do not use an isolation transformer for this test. Plug the completely

reassembled receiver directly into the ac outlet.

2. Connect a 1.5k, 10w resistor paralleled by a 0.15uf. capacitor between

each exposed metallic cabinet part and a good earth ground such as a
water pipe, as shown above.

3. Use an ac voltmeter with at least 5000 ohms volt sensitivity to measure
the potential across the resistor.

4. The potential at any point should not exceed 0.75 volts. A leakage current

tester may be used to make this test; leakage current must not exceed

0.5 milliamps. If a measurement is outside of the specified limits, there is
a possibility of shock hazard. The receiver should be repaired and
rechecked before returning it to the customer.

5. Repeat the above procedure with the ac plug reversed.( Note: An ac
adapter is necessary when a polarized plug is used. Do not defeat the
polarizing feature of the plug.)

The primary source of X-radiation in this television receiver is the picture
tube. The picture tube utilized in this chassis is specially constructed to limit
X-radiation emissions. For continued X-radiation protection, the replacement
tube must be the same type as the original, including suffix letter, or a Philips
approved type.

Many electrical and mechanical parts in Philips television sets have special
safety related characteristics. These characteristics are often not evident from
visual inspection nor can the protection afforded by them necessarily be
obtained by using replacement components rated for higher voltage, wattage,
etc. The use of a substitute part which does not have the same safety
characteristics as the Philips recommended replacement part shown in this
service manual may create shock, fire, or other hazards

Leakage Current Cold Check

Leakage Current Hot Check

Picture Tube Replacement

Parts Replacement

1500 ohm, 10W

0.15 uF

WATER
PIPE
EARTH
GROUND

TO
INSTRUMENTS
EXPOSED
METAL PARTS