Page 1
Register your product and get support at
19PFL3403/77
EN User manual 3
Page 2
Page 3
3
Select your language 26
Automatically install channels 26
Fine tune channels 26
Exclude channels from a list 27
10 Troubleshooting 28
11 Product information 29
Contents
1 Notice 4
2 Important 5
Safety 5
Screen care 6
Environmental care 6
3 Your TV 7
TV overview 7
Remote control 8
4 Get started 10
Position the TV 10
Wall mount the TV 10
Connect the antenna cable 10
To connect the power cord 11
Insert the remote control batteries 11
5 Use your TV 13
Switch your TV on/off or to standby 13
Switch channels 13
Adjust volume 13
6 Use more of your TV 14
Adjust picture and sound settings 14
Use timers 16
Create and use lists of favorite channels
17
View closed captions (subtitles) 18
Use child control and rating locks 19
7 Use your TV as a PC monitor 23
Congure your TV in PC mode 23
Adjust display settings for PC mode 23
8 Use your TV in HDTV mode 24
Congure your TV in HD mode 24
Adjust display settings in HD mode 24
9 Install channels 26
En glish
EN
Page 4
4
One of Philips’ leading Business Principles is to
take all necessary health and safety measures
for our products, to comply with all applicable
legal requirements and to stay well within
the EMF standards applicable at the time of
producing the products.
Philips is committed to develop, produce and
market products that cause no adverse health
effects. Philips conrms that if its products are
handled properly for their intended use, they
are safe to use according to scientic evidence
available today.
Philips plays an active role in the development
of international EMF and safety standards,
enabling Philips to anticipate further
developments in standardisation for early
integration in its products.
Copyright
VESA, FDMI and the VESA Mounting Compliant
logo are trademarks of the Video Electronics
Standards Association.
® Kensington and Micro Saver are registered
US trademarks of ACCO World corporation
with issued registrations and pending
applications in other countries throughout the
world.
All other registered and unregistered
trademarks are the proper ty of their respective
owners.
1 Notice
2008 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specications are subject to change without
notice. Trademarks are the proper ty of
Koninklijke Philips Electronics N.V. or their
respective owners.
Philips reserves the right to change products at
any time without being obliged to adjust earlier
supplies accordingly.
The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other than
those specied herein, conrmation of their
validity and suitability must be obtained. Philips
warrants that the material itself does not
infringe any United States patents. No further
warranty is expressed or implied.
Warranty
No components are user serviceable. Do not
open or remove covers to the inside of the
product. Repairs may only be done by Philips
Service Centres and ofcial repair shops. Failure
to do so shall void any warranty, stated or
implied.
Any operation expressly prohibited in
this manual, any adjustments, or assembly
procedures not recommended or authorised in
this manual shall void the warranty.
Pixel characteristics
This LCD product has a high number of
colour pixels. Although it has effective pixels of
99.999% or more, black dots or bright points of
light (red, green or blue) may appear constantly
on the screen. This is a structural property of
the display (within common industry standards)
and is not a malfunction.
Compliance with EMF
Koninklijke Philips Electronics N.V. manufactures
and sells many products targeted at consumers,
which, like any electronic apparatus, in
general have the ability to emit and receive
electromagnetic signals.
EN
Page 5
5
If placing the TV on a at, solid surface be
sure to use only the supplied stand. Do not
move the TV if the stand is not properly
screwed to the TV.
Wall mounting of the TV should only be
performed by qualied personnel. The TV
must only be mounted on an appropriate
wall bracket and on a wall that can safely
hold the weight of the TV. Improper wall
mounting can result in severe injury or
damage. Do not attempt to wall mount
the TV yourself.
If the TV is mounted on a swivel base or
swivel arm, ensure no strain is placed on
the power cord when the TV is swivelled.
Strain on the power cord can loosen
connections and cause arcing or re.
Disconnect the TV from the mains and
antenna before lightning storms. During
lightning storms do not touch any part of
the TV, mains cord or antenna cable.
Be sure that you have full access to the
mains cord for easy disconnection of the
TV from the mains.
When disconnecting the TV from the
mains, be sure to:
1 Turn off the TV, then the mains power (if
available).
2 Unplug the mains cord from the mains
socket outlet.
3 Unplug the mains cord from the power
connector at the back of the TV. Always
pull the mains cord by the plug. Do not
pull the mains cord.
Permanent hearing loss can occur if you
use earphones or headphones at high
volumes. Though high volume may sound
•
•
•
•
•
•
•
2 Important
Read this user manual before you start to use
this product.
Pay close attention to this section and follow
the safety and screen care instructions. The
product warranty does not apply if damage is
caused by failing to follow these instructions.
The model and serial number of your TV can
be found on the back of the TV as well as on
the packaging.
Safety
Two people are required to lift and carr y a
TV that weighs more than 25 kilos (55lb).
Improper handling of the TV can result in
serious injury.
If transporting the TV in low temperatures
(less than 5°C), open the box and
wait until the TV matches the ambient
temperature of the room before
unpacking.
To avoid short circuit, do not expose the
TV, remote control or remote control
batteries to rain or water.
To avoid risk of re or electric shock,
do not place the TV, remote control or
remote control batteries near naked ame
sources (e.g. lighted candles) and other
heat sources including direct sunlight.
Do not place vessels lled with water on
top of or near to the TV. Spilling water into
the TV can result in electric shock. If you
spill water into the TV, do not operate the
TV. Immediately disconnect the TV from
the power and have the TV checked by a
qualied technician.
Do not install the TV in a conned space
such as a bookcase. Leave a space of
at least 10cm (four inches) around the
TV for ventilation. Be sure air ow is not
obstructed.
•
•
•
•
•
•
En glish
EN
Page 6
6
and reused. When you see the crossed-out
wheel bin symbol attached to a product, it
means the product is covered by the European
Directive 2002/96/EC:
Do not dispose your used product with
household waste. Ask your dealer for
information on how to safely dispose of the
product. Uncontrolled waste disposal harms
both the environment and human health.
Disposing used batteries
The supplied batteries do not contain
mercury or cadmium. Dispose supplied and all
other used batteries according to your local
regulations.
Power consumption
The TV consumes minimal energy in standby
mode to minimize environmental impact. Active
power consumption is displayed at the back of
the TV. For more product specications, see the
product leaet at www.philips.com/support.
normal over time, it can damage your
hearing. To protect your hearing, limit the
amount of time you use earphones or
headphones at high volume.
Screen care
Turn off and unplug the mains cord before
cleaning the screen. Clean the screen with
a soft, dry cloth. Do not use substances
such as household cleaning agents as these
may damage the screen.
To avoid deformations or colour fading,
wipe off water droplets as soon as possible.
Do not touch, push, rub or strike the
screen with hard objects as this may
damage the screen permanently.
Where possible, avoid stationary images
that remain on-screen for extended
periods of time. Examples include screen
menus, teletext pages, black bars or stock
market tickers. If you must use stationary
images, reduce the screen contrast and
brightness to avoid screen damage.
Environmental care
Recycling your packaging
The packaging of this product is intended to
be recycled. Contact your local authorities for
information on how to recycle the packaging.
Disposing your used product
Your product is manufactured with high-quality
materials and components that can be recycled
•
•
•
•
EN
Page 7
7
Connectors
a HDMI
HDMI for DVD player, HD digital receiver,
HD game console, PC, etc.
b
VGA AUDIO
Mini-jack connector for PC audio when
connecting a PC via DVI-HDMI or VGA.
c
VGA PC
To connect a PC.
d
YPBPR
Component video input with YPbPr and
Audio L/R connectors for DVD, digital
receiver or game console, etc.
e
AV1
Composite video input to be used with
Audio L/R connectors for camcorder,
game console, etc.
f
TV (75 )
Antenna input
g
SERV C
For software update.
h
SIDE AV
Composite video (side) to be used with
Audio L/R connectors for camcorder,
game console, etc.
i
S-VIDEO
1
2
3 4 5 6 7
8
9
10
1
2
3 4 5 6 7
8
9
10
3 Your TV
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
TV overview
This section gives you an overview of
commonly-used TV controls and functions.
Side controls and indicators
a Standby indicator / remote control
sensor
b
POWER: Switches the TV on from
standby or back to standby. The TV is
not powered off completely unless it is
physically unplugged.
c
CHANNEL + / -: Switches to the next or
previous channel.
d
MENU: Toggles the main menu on or off.
e VOLUME + / -: Increases or decreases
volume.
2
3
5
4
POWER
CHANNEL
MENU
VOLUME
1
2
3
5
4
POWER
CHANNEL
MENU
VOLUME
1
En glish
EN
Page 8
8
c Not used.
d SLEEP
Sets a delay after which the TV switches
to standby.
e
TIMER
Sets the clock and timers.
f
SMART SOUND
Selects pre-dened sound settings.
g
Navigation keys
Navigates through the menus.
h
MENU/BACK
Toggles the menu on or off or returns to
a previous screen.
i
VOL + / -
Increases or decreases volume.
j
Mute
Mutes or unmutes audio.
k
Number buttons
Selects a channel, page or setting.
l
STATUS/EXIT
Displays status information or exits the
menu.
m
SAP
Selects Secondary Audio Program (SAP),
stereo or mono.
n
CC
Displays closed captions settings.
o
SURF
Displays a list of all channels marked as
favorite.
p
TV/PC
Toggles between PC mode and the last
accessed mode.
q
SMART PIC
Selects pre-dened picture settings.
r
OK
Activates a selection or accesses the
menu.
s
FORMAT
S-Video (side) to be used with Audio L/R
connectors for camcorder, game console,
etc. When you use the S-Video (side) for
video signals, do not use the Composite
video (side) input for video signals.
j
Headphones
Headphone stereo mini jack.
For software update.
Remote control
a Power
Switches the TV on from standby or
back to standby. The TV is not powered
off completely unless it is physically
unplugged.
b
SOURCE
Selects connected devices.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
EN
Page 9
9
Selects a picture format.
t CH + / -
Switches to the next or previous channel.
u
A/CH
Toggles between the current channel and the
last viewed channel.
En glish
EN
Page 10
10
Wall mount the TV
Warning
Wall mounting of the TV should only be performed by
qualied installers. Koninklijke Philips Electronics N.V.
bears no responsibility for improper mounting that
results in accident or injury.
•
Screen
size
VESA-compatible
bracket (mm)
Bolt type and
min length
(not supplied)
19”
(48cm)
Adjustable 100 x
100
M4 x 10mm
26”
(66cm)
Adjustable 200 x
100
M4 x 10mm
The minimum bolt length is 10mm. If you use
a spacer, the bolt length should be the spacer
length plus 10mm. For example, if you use a
40mm spacer, the bolt length should be 50mm
(40mm + 10mm).
Connect the antenna cable
Connect the antenna cable to the TV antenna
socket (75 ) at the back of the TV.
4 Get started
This section supplements information in the
Quick Start. For information about how to
mount and install your TV, refer to the Quick
Start.
Position the TV
Warning
Do not insert the power plug into the wall socket
before all the connections are made.
Large screen TVs are heavy. Two people are required to
carry and handle a large screen TV.
Before you move the TV, disconnect the cables to
prevent breakage.
•
•
•
In addition to reading and understanding the
safety instructions (see ‘Safety’ on page 5),
consider the following before positioning your
TV:
Ensure that you always have easy access to
the power cord or plug to disconnect the
TV from the power.
If the TV is mounted on a swivel base,
ensure that no strain is placed on the
power cord when the TV is swiveled.
Strain on the power cord can loosen
connections.
The ideal viewing distance for watching TV
is three times its screen size.
Position the TV where light does not fall on
the screen.
Connect your devices before you position
the TV.
Use a Kensington lock
There is a Kensington security slot at the back
of the TV. If you connect a Kensington lock
(not supplied), position the TV near a heavy or
immovable object that you can attach the cable
to.
•
•
•
•
•
EN
Page 11
11
To disconnect the TV from the power
Disconnect the TV from the power in one of
the following ways:
Unplug the power cord from the power
connector at the back of the TV.
Unplug the power cord from the power
socket outlet.
Pull the power cord by the plug; do not pull on
the power cord.
Insert the remote control
batteries
1
Slide the battery cover off the back of the
remote control.
2 Insert the 2 supplied batteries (AAA). Be
sure the + and - ends of the batteries line
up with the markings inside the case.
3 Slide the cover back into position.
•
•
To connect the power cord
Warning
Verify that your mains voltage corresponds with the
voltage printed at the back of the TV. Do not insert the
mains cord if the voltage is different.
•
1 Locate the power connector at the back of
the TV.
The location of the power connector
varies according to TV model.
2 Insert the power cord fully into the power
connector.
3 Connect the power cord plug to the
power outlet. Ensure that the cord is tightly
secured at both ends.
CableCable
En glish
EN
Page 12
12
Note
Remove the batteries if you are not going to use the
remote control for an extended period of time.
•
EN
Page 13
13
Press CH + / - or key in the number on
the remote control.
Press CHANNEL + / - on the side of the
TV.
Adjust volume
To increase or decrease volume
Press VOL + / - on the remote control or
press VOLUME + / - on the side of the TV.
To mute or unmute sound
Press on the remote control to mute
the sound.
Press again to restore the sound.
To adjust headphone volume
Press VOL + / - on the remote control or
press VOLUME + / - on the side of the TV.
When headphones are plugged into the TV,
the loud speakers are automatically muted.
•
•
•
•
•
•
CHANNELCHANNEL
5 Use your TV
This section helps you perform basic TV
operations.
Switch your TV on/off or to
standby
To switch on
If the standby indicator (2) is off, press
POWER (1) at the side of the TV.
If the standby indicator (2) is red, press
on the remote control.
To switch to standby
Press on the remote control.
The standby indicator (2) switches to
red.
To switch off
Press POWER (1) at the side of the TV.
Switch channels
•
•
•
»
•
En glish
EN
Page 14
14
[Color Temp.]: Makes colors more vivid
and improve the resolution of details in
bright colors. You can switch this feature
on or off.
[Noise Reduction]: Filters and reduces
noise in an image.
Use smart picture settings
You can use smar t picture instead of the
manual picture adjustments to set your TV to a
predened setting.
The settings are pre-dened to suit different
viewing environments.
1 Press MENU/BACK and select [Picture].
2 Press OK.
3 Press to highlight [Smart Pic] and press
or to select a setting.
4 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Tip
Press SMART PIC on the remote control repeatedly
to toggle the available settings.
•
The following settings are pre-dened factory
settings to match your viewing environment.
[Rich]
[Natural]
[Soft]
[Personal]
Change picture format
1 Press MENU/BACK and select [Features]
> [Format]
2 Press or to select the following picture
formats.
•
•
•
•
•
•
6 Use more of
your TV
Adjust picture and sound
settings
This section describes how to adjust picture
and sound settings.
Adjust picture settings
1 Press MENU/BACK and select [Picture].
2 Press OK.
3 Press or to highlight [Picture].
4 Press or to adjust the settings.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
The following smart picture settings can be
congured. Depending on the format of the
picture source, some picture settings are not
available.
[Brightness]
: Adjusts the intensity and
details of dark areas.
[Contrast]: Adjusts the intensity of bright
areas, keeping dark areas unchanged.
[Tint]: Adjusts the color balance in an
image.
[Color]: Adjusts color saturation.
[Sharpness]: Adjusts the level of sharpness
in image details.
•
•
•
•
•
C
h. Setu
p
Smart Pic
Brightness
Contrast
Tint
Color
Sharpness
Color Temp
Noise Reduction
75
60
0
50
75
Picture Sound Features Install
Personal
Normal
Off
: SEL
MENU
: ADJ
: EXIT
C
h. Setu
p
Smart Pic
Brightness
Contrast
Tint
Color
Sharpness
Color Temp
Noise Reduction
75
60
0
50
75
Picture Sound Features Install
Personal
Normal
Off
: SEL
MENU
: ADJ
: EXIT
EN
Page 15
15
[Bass]: Adjusts the low frequency sound
levels.
[Balance]
: Adjusts the balance of the right
and left speakers to best suit your listening
position.
[AVL]
: Reduces sudden changes in volume,
for example, during commecials or when
switching channels. Set on or off.
[MTS]: Multi-channel TV sound. Select
mono, stereo or a Secondary Audio
Program (SAP).
Use smart sound settings
You can use smar t sound instead of the manual
sound settings to set your TV to a predened
setting.
The settings are pre-dened to suit different
listening environments.
1 Press MENU/BACK and select [Sound].
2 Press OK.
3 Press to highlight [Smart Sound] and
press or to select a setting.
4 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Tip
Toggle SMART SOUND to access the settings.•
The following settings are pre-dened to match
your listening environment.
[Movie]
[Music]
[Voice]
[Personal]
Use Back Light
Adjust the brightness of the TV backlight to suit
your surrounding ambient lighting.
1 Press MENU/BACK and select [Features]
> [Back Light].
2 Press or to adjust the level.
•
•
•
•
•
•
•
•
Tip
Toggle FORMAT on the remote control to access
the formats.
•
[4:3]: Shows the classic 4:3
format.
[Widescreen]: Stretches
the classic 4:3 format to
16:9.
Adjust sound settings
This section describes how to adjust sound
settings.
1 Press MENU/BACK and select [Sound].
2 Press OK.
3 Press or to select an item and press
or to adjust the setting.
4 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Summary of sound settings
[Smart Sound]: Pre-dened sound settings
to suit your listening environment.
[Treble]: Adjusts the high frequency sound
levels.
•
•
C
h. Setu
p
Smart Sound
Treble
Bass
Balance
AVL
MTS
40
60
50
Picture Sound Features Install
Personal
Off
Mono
: SEL
MENU
: ADJ
: EXIT
C
h. Setu
p
Smart Sound
Treble
Bass
Balance
AVL
MTS
40
60
50
Picture Sound Features Install
Personal
Off
Mono
: SEL
MENU
: ADJ
: EXIT
En glish
EN
Page 16
16
Automatically switch the TV to
standby (Sleeptimer)
Sleeptimer switches the TV to standby after a
delay. You can always switch off your TV earlier
or reset the sleeptimer during the countdown.
1 Toggle SLEEP on the remote control to
cycle through the sleep timer settings:
off, 15, 30, 45, 60, 90, 120, 180 and 240
minutes.
Tip
Press SLEEP once to view the remaining time before
the TV switches to standby. Press SLEEP repeatedly to
change the setting or to turn off sleep timer.
•
Set the clock
1 Press MENU/BACK and select [Features]
> [Timer].
2 Press OK.
3 Press to highlight [Current Time]
and press or to select the hours or
minutes.
4 Press or to adjust the hours or
minutes.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Timer
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Picture Sound Features Install
Off
09:30
Off
--:--
--:--
TV
2
: SEL
MENU
: ADJ
: EXIT
Timer
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Picture Sound Features Install
Off
09:30
Off
--:--
--:-TV
2
: SEL
MENU
: ADJ
: EXIT
3 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Use Contrast +
Optimizes the contrast settings for overall
picture quality.
1 Press MENU/BACK and select [Features]
> [Contrast +].
2 Press or to turn on [Contrast +].
3 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Use timers
This section describes how to set the clock and
switch the TV on or off at a specied time.
C
h. Setu
p
Format
Timer
Closed Caption
Parental Control
Back Light
Contrast +
Geometry
Mode Selection
5
Picture Sound Features Install
Widescreen
>
>
>
On
>
PC
: SEL
MENU
: ADJ
: EXIT
C
h. Setu
p
Format
Timer
Closed Caption
Parental Control
Back Light
Contrast +
Geometry
Mode Selection
5
Picture Sound Features Install
Widescreen
>
>
>
On
>
PC
: SEL
MENU
: ADJ
: EXIT
EN
Page 17
17
12 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Check timer status
Check the status of the timers that you set for
current time, sleep timer and TV timer.
1 Press TIMER on the remote control.
The TV timer status is displayed.
You can change the timer settings from
this screen.
2 Press TIMER again to exit the timer display.
Create and use lists of
favorite channels
This section describes how to set up a list of
your preferred TV channels.
»
Timer
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Picture Sound Features Install
Off
09:30
On
10:00
11:00
TV
5
: SEL
MENU
: ADJ
: EXIT
Timer
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Picture Sound Features Install
Off
09:30
On
10:00
11:00
TV
5
: SEL
MENU
: ADJ
: EXIT
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Off
09:30
On
10:00
11:00
TV
5
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Off
09:30
On
10:00
11:00
TV
5
Activate the timer
1 Press MENU/BACK and select [Features]
> [Timer].
2 Press OK.
3 Press and select [Activate] > [On].
Set the TV timer
1 Press MENU/BACK and select [Features]
> [Timer].
2 Press OK.
3 Press to highlight [Start Time].
4 Press to select the hour eld, then press
or to adjust the hours.
5 Press to select the minute eld, then
press or to adjust the minutes.
6 Press to highlight [Stop Time].
7 Press to select the hour eld, then press
or to adjust the hours.
8 Press to select the minute eld, then
press or to adjust the minutes.
9 Press to highlight [Source].
10 Press or to select the source.
11 If you select the TV source, set the channel
for the TV to switch to from standby. Press
to highlight [Channel No.], then press
or to select the number.
Timer
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Picture Sound Features Install
Off
09:30
On
--:--
--:--
TV
2
: SEL
MENU
: ADJ
: EXIT
Timer
Sleep
Current Time
Activate
Start Time
Stop Time
Source
Channel No.
Picture Sound Features Install
Off
09:30
On
--:--
--:-TV
2
: SEL
MENU
: ADJ
: EXIT
En glish
EN
Page 18
18
Note
This television provides a display of television closed
captioning that conforms with the EIA-608 standard
and in accordance with Sections 15.119 of the
FCCrules.
If you connect your set-top box via HDMI or
component video input, you cannot select closed
caption through the TV. You can select closed caption
through the set-top box only.
The captions do not always use correct spelling and
grammar.
Not all TV programs and product commercials include
closed caption information. Refer to your area TV
program listings for the TV channels and times of closed
caption shows. The captioned programs are usually
noted in the TV listings with service marks such as ‘CC’.
•
•
•
•
Turn on Closed Caption
1 Press MENU/BACK and select [Features]
> [Closed Caption].
2 Press OK.
3 Press or to turn on [CC Setting].
4 Press to highlight [CC Mode] and press
or to select a setting.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Closed Caption
CC Setting
CC Mode
Picture Sound Features Install
On
CC1
: SEL
MENU
: ADJ
: EXIT
Closed Caption
CC Setting
CC Mode
Picture Sound Features Install
On
CC1
: SEL
MENU
: ADJ
: EXIT
Create and use your favorite list
1 Press MENU/BACK and select [Install] >
[Fav. Channel].
2 Press OK.
3 Press or to highlight the favorite
channel number.
4 Use the number keys to key in the channel
number.
The channel number is displayed
beside the favorite list number. Enter
up to six favorite channels in the list.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
6 Press SURF repeatedly to cycle through
the favorite channels.
View closed captions
(subtitles)
The caption service displays transmitted
closed caption text. The captioned text can be
displayed permanently or only when the TV is
muted.
»
Fav. Channel
FAV 1
FAV 2
FAV 3
FAV 4
FAV 5
FAV 6
Picture Sound Features Install
5
12
22
25
30
38
: SEL
MENU
: ADJ
: EXIT
Fav. Channel
FAV 1
FAV 2
FAV 3
FAV 4
FAV 5
FAV 6
Picture Sound Features Install
5
12
22
25
30
38
: SEL
MENU
: ADJ
: EXIT
EN
Page 19
19
Turn on parental control
1 Press MENU/BACK and select [Features]
> [Parental Control].
2 Press OK.
You are prompted to enter your
password.
3 Enter your PIN on remote control.
If you have never set a PIN before,
enter 0000.
If you have forgotten your PIN, reset
it (see ‘Change your password’ on
page 19).
The [Parental Control] menu is
displayed.
4 Press to highlight [Parental Control] and
press to turn on [Parental Control].
Use TV ratings lock
Your TV is equipped with a V-chip that allows
you to control access to individual programs
based on their age rating and content rating.
The program content advisory data are from
the broadcaster or by the program provider.
If you receive channels through a set-top box
or cable box connected by HDMI, you cannot
use the TV ratings lock. Your set-top box or
cable box must be connected through RF or AV
connectors.
1 Access the [Parental Control] menu.
2 Press and select [TV Rating].
3 Press OK.
»
•
•
Parental Control
Change Password
Parental Control
TV Rating
Movie Rating
U
nrated Bl
ock
No Rating Block
Picture Sound Features Install
>
Off
>
>
Off
Off
: SEL
MENU
: ADJ
: EXIT
Parental Control
Change Password
Parental Control
TV Rating
Movie Rating
U
nrated Bl
ock
No Rating Block
Picture Sound Features Install
>
Off
>
>
Off
Off
: SEL
MENU
: ADJ
: EXIT
Summary of caption services
Service Description
CC-1 and
CC-2
Dialog and descriptions for the
action on the captioned TV
program show on screen. Usually
CC1 is the most used. CC 2 can
be used for alternate languages if
they are transmitted.
Use child control and rating
locks
This section describes how to lock or unlock
the TV. You can set a PIN code or use ratings
to prevent children from watching certain
programs or channels.
Change your password
Follow these steps to set your PIN or to reset
your PIN if you have forgotten it.
1 Press MENU/BACK and select [Features]
> [Parental Control].
2 Press OK.
You are prompted to enter a
password.
3 Enter your 4-digit PIN on the number keys
of the remote control.
If you have never set your PIN before,
enter 0000.
If you have set your PIN but have
forgotten it, enter 0711.
The [Parental Control] menu is
displayed.
4 Select [Change Password] and press OK.
5 Enter a new PIN, and then enter the PIN
again to conrm.
6 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
»
•
•
En glish
EN
Page 20
20
Summary of TV ratings
Age rating Content
rating
All None
None None
TV-Y
: Appropriate for children of
all ages with themes and elements
suitable for children aged 2-6.
None
TV-Y7
: Programs designed for
children age 7 and older.
[(FV)
Fantasy
Violence]
TV-G
: Programs suitable for all
ages. These programs contain little
or no violence, no strong language
and little or no sexual dialog or
situations.
None
TV-PG
: Programs contain
elements that some parents
may nd unsuitable for younger
children and which may need
parental guidance. The program
may contain moderate violence,
sexual dialog and/or situations and
some strong language.
[(D)
Dialog]
[(L)
Language]
[(S) Sex]
[(V)
Violence]
TV-14
: Programs contain elements
that may not be suitable for
children under 14 years of age.
These programs include one or
more of the following: intense
violence, intense sexual situations,
suggestive dialog and strong
language.
[(D)
Dialog]
[(L)
Language]
[(S) Sex]
[(V)
Violence]
TV-MA
: Programs are designed to
be viewed by adults and may be
unsuitable for children under the
age of 17. These programs may
contain graphical violence, explicit
sexual activity and/or crude or
indecent language.
[(L)
Language]
[(S) Sex]
[(V)
Violence]
Use movie ratings lock
This section describes how to control viewing
of movies based on their Motion Picture
Association of America (MPAA) rating.
4 Press to highlight a rating and press OK
to select [View] or [Block].
When you block a rating, all ratings in the
younger age categories are automatically
blocked.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
TV Rating
None
TV - Y
TV - Y7
TV - G
TV - PG
TV - 14
TV - MA
Picture Sound Features Install
FV
V
All
V
V
V
V
V
V
V
S
V
V
V
V
V
V
V
D
V
V
L
V
V
V
: SEL
MENU
: ADJ
: EXIT
TV Rating
None
TV - Y
TV - Y7
TV - G
TV - PG
TV - 14
TV - MA
Picture Sound Features Install
FV
V
All
V
V
V
V
V
V
V
S
V
V
V
V
V
V
V
D
V
V
L
V
V
V
: SEL
MENU
: ADJ
: EXIT
EN
Page 21
21
Summary of US movie ratings
Rating Description
All All items in the ratings list are
locked.
NR
Not rated.
G Movies with a mild content,
suitable for all ages.
PG Movies for which parental
guidance is recommended. They
may contain a few racy or violent
scenes or maybe some bad
language.
PG -13 Movies for which parental
guidance may be recommended if
under age 13.
R Restricted. The movies usually
contain offensive sex or bad
language and may be unsuitable
for children under the age of 17.
Parental guidance or permission
needed.
NC-17
Even with parental permission,
forbidden under age 17. More
offensive sex, violence or bad
language.
X
Movies which generally focus on
sex, violence and/or bad language.
Also known as pornography.
Block unrated or no rating programs
Block unrated programs such as “director’s cut”
edition or programs with no advisory data.
1 Access the [Parental Control] menu.
2 Press to highlight [Unrated Block] or
[No Rating Block].
3 Press OK.
4 Press or to select [On].
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
1 Access the [Parental Control] menu.
2 Press and select [Movie Rating].
3 Press OK.
4 Press to highlight a rating and press
or to change the setting to [View] or
[Block].
When you block a movie rating, all items
for ages below that movie rating are
automatically blocked.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Movie Rating
N/R
G
PG
PG-13
R
NC-17
X
Picture Sound Features Install
View
Block
View
View
View
View
View
: SEL
MENU
: ADJ
: EXIT
Movie Rating
N/R
G
PG
PG-13
R
NC-17
X
Picture Sound Features Install
View
Block
View
View
View
View
View
: SEL
MENU
: ADJ
: EXIT
En glish
EN
Page 22
22
Unlock blocked channels or programs
To view programs or channels blocked with the
parental control blocking options, unlock them
with the password or turn off parental control.
Turn off parental control
1 Access the [Parental Control] menu.
2 Press to highlight [Parental Control]
and press or to turn off [Parental
Control].
3 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Parental Control
Change Password
Parental Control
TV Rating
Movie Rating
U
nrated Bl
ock
No Rating Block
Picture Sound Features Install
>
Off
>
>
On
On
: SEL
MENU
: ADJ
: EXIT
Parental Control
Change Password
Parental Control
TV Rating
Movie Rating
U
nrated Bl
ock
No Rating Block
Picture Sound Features Install
>
Off
>
>
On
On
: SEL
MENU
: ADJ
: EXIT
EN
Page 23
23
If necessary, adjust the picture position to the
center of the screen with the cursor buttons.
Adjust display settings for PC
mode
Adjust your TV display settings in PC mode.
1 Press MENU/BACK and select [Features]
> [Geometry].
2 Press OK.
3 Press or to select an item.
4 Press or to adjust the setting.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
You can congure the following display settings
for PC mode:
[Auto Adjust]: Synchronizes the phase and
clock on the TV and PC.
[Horizontal Shift] and [Vertical Shift]:
Adjusts the horizontal and vertical position
of the picture.
[Clock] and [Phase]: Fine-tunes the TV to
match the display settings of the PC.
•
•
•
Geometry
Auto Adjust
Horizontal Shift
Vertical Shift
Clock
Phase
+50
+50
100
100
Picture Sound Features Install
: SEL
MENU
: ADJ
: EXIT
Geometry
Auto Adjust
Horizontal Shift
Vertical Shift
Clock
Phase
+50
+50
100
100
Picture Sound Features Install
: SEL
MENU
: ADJ
: EXIT
7 Use your TV as
a PC monitor
For information about how to connect a PC to
the TV, see the Quick Star t.
Caution
Before you connect your PC, set the PC monitor
refresh rate to 60Hz.
•
Congure your TV in PC
mode
1
Press SOURCE and select PC, then press
OK.
Tip
Toggle TV/PC to switch to PC and the last accessed
mode.
•
Note
Certain picture and sound features are not available in
PC mode.
•
Supported screen resolutions
The following screen resolutions are supported
in PC mode:
Resolution Refresh rate
640 x 480 60Hz
800 x 600 60Hz
1024 x 768 60Hz
1280 x 768 60Hz
1280 x 1024 60Hz
En glish
EN
Page 24
24
Note
Certain picture and sound features are not available in
HDMI and YCbCr modes.
•
Supported screen resolutions
The following screen resolutions are supported
in HDMI and YPbPr modes:
Resolution Refresh rate
480i 60Hz
480p 60Hz
576i 50Hz
576p 50Hz
720p 50Hz
720p 60Hz
1080i 50Hz
1080i 60Hz
If necessary, adjust the picture position to the
center of the screen with the cursor buttons.
Adjust display settings in HD
mode
Adjust your TV display settings in HD mode.
1 Press MENU/BACK and select [Features]
> [Geometry].
2 Press OK.
3 Press or to select an item.
Geometry
Horizontal Shift
Vertical Shift
+50
+50
Picture Sound Features Install
: SEL
MENU
: ADJ
: EXIT
Geometry
Horizontal Shift
Vertical Shift
+50
+50
Picture Sound Features Install
: SEL
MENU
: ADJ
: EXIT
8 Use your TV in
HDTV mode
Not all models can be congured in high
denition (HD) mode. For information about
your set, see the specication.
When you connect an HD device to your TV,
congure the display format of your TV. You
might also have to congure the display format
of your HD device. For information about
conguring your device, see the documentation
of the device.
Congure your TV in HD
mode
1
Connect your HD device to the TV. Refer
to the Quick Start.
2 Press SOURCE and select HDMI or
YPBPR, then press OK.
3 Press MENU/BACK and select [Features]
> [Mode Selection].
4 Press OK.
5 Press or to select a mode.
6 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
C
h. Setu
p
Format
Timer
Closed Caption
Parental Control
Back Light
Contrast +
Geometry
Mode Selection
5
Picture Sound Features Install
Widescreen
>
>
>
Off
>
HDMI
: SEL
MENU
: ADJ
: EXIT
C
h. Setu
p
Format
Timer
Closed Caption
Parental Control
Back Light
Contrast +
Geometry
Mode Selection
5
Picture Sound Features Install
Widescreen
>
>
>
Off
>
HDMI
: SEL
MENU
: ADJ
: EXIT
EN
Page 25
25
4 Press or to adjust the setting.
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
The following display settings can be congured
when an HD device is connected to the TV.
[Horizontal Shift]
and [Vertical Shift]:
Adjusts the horizontal and vertical position
of the picture.
•
En glish
EN
Page 26
26
3 Press and select [System].
4 Press or and select [AUTO], [PAL M],
[PAL N] or [NTSC].
5 Press to highlight [Auto Program] and
press OK.
The TV detects the [Antenna] or
[Cable] signal that you have selected
and search for all the available
channels.
When the search completes, the TV
switches to the rst channel found.
6 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Fine tune channels
You can manually ne tune channels when the
reception is poor.
1 Press CH + / - or use the number keys to
select the channel to ne tune.
•
•
Ch. Setup
Tuner Mode
System
Auto Program
Fine Tune
Picture Sound Features Install
Antenna
Auto
>
193.25Mhz
: SEL
MENU
: ADJ
: EXIT
Ch. Setup
Tuner Mode
System
Auto Program
Fine Tune
Picture Sound Features Install
Antenna
Auto
>
193.25Mhz
: SEL
MENU
: ADJ
: EXIT
Ch. Setup
Tuner Mode
System
Auto Program
Fine Tune
Picture Sound Features Install
Antenna
NTSC
>
195.30Mhz
: SEL
MENU
: ADJ
: EXIT
Ch. Setup
Tuner Mode
System
Auto Program
Fine Tune
Picture Sound Features Install
Antenna
NTSC
>
195.30Mhz
: SEL
MENU
: ADJ
: EXIT
9 Install channels
The rst time you setup your TV, you are
prompted to select a menu language and to
install TV and digital radio channels (if available).
This chapter provides instructions on how to
reinstall and ne-tune channels.
Select your language
a Press MENU/BACK and select [Install] >
[Language].
b Press or to select a language, then
press OK.
c
Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Automatically install channels
This section describes how to search and store
channels automatically. Instructions are for both
digital and analogue channels.
1 Press MENU/BACK and select [Install] >
[Ch. Setup] > [Tuner Mode].
2 Press or and select [Antenna] or
[Cable].
C
h. Setu
p
Language
Ch. Setup
List
Fav. Channel
Picture Sound Features Install
English
>
>
>
: SEL
MENU
: ADJ
: EXIT
C
h. Setu
p
Language
Ch. Setup
List
Fav. Channel
Picture Sound Features Install
English
>
>
>
: SEL
MENU
: ADJ
: EXIT
EN
Page 27
27
5 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
List
Current Channel
In List
Picture Sound Features Install
30
Off
: SEL
MENU
: ADJ
: EXIT
List
Current Channel
In List
Picture Sound Features Install
30
Off
: SEL
MENU
: ADJ
: EXIT
2 Press MENU/BACK and select [Install] >
[Ch. Setup] > [Fine Tune].
3 Press or to adjust the frequency
setting.
4 Press MENU/BACK to return to the
previous menu, or press STATUS/EXIT to
exit.
Exclude channels from a list
You can exclude a channel from your list of
channels. Excluded channels are not accessed
when you press CH + / - on the remote
control or CHANNEL + / - on the side of
the TV. Excluded channels can be accessed,
however, by pressing the number keys on the
remote control. It can be useful to exclude
channels with weak signals.
1 Press MENU/BACK and select [Install] >
[List].
2 Press OK.
3 Press or to select a channel number.
4 Press to highlight [In List], and press
or to select [Off].
Ch. Setup
Tuner Mode
System
Auto Program
Fine Tune
Picture Sound Features Install
Antenna
Auto
>
195.30Mhz
: SEL
MENU
: ADJ
: EXIT
Ch. Setup
Tuner Mode
System
Auto Program
Fine Tune
Picture Sound Features Install
Antenna
Auto
>
195.30Mhz
: SEL
MENU
: ADJ
: EXIT
En glish
EN
Page 28
28
Check the connections.
Set the PC refresh rate to 60Hz.
Snowy dots and interference
If the antenna is located in the fringe area of a
television signal where the signal is weak, the
picture may appear snowy. When the signal is
weak, it may be necessary to install a special
antenna to improve the reception.
Adjust the position and orientation of
the indoor/outdoor antenna.
Check the connection of antenna.
Fine tune the program.
Try another program. Broadcasting
failure may happen.
Ghost
“Ghosting” occurs when the television signal
follows two paths. One is the direct path,
the other is reected from tall buildings, hills,
or other objects. Changing the direction or
position of the antenna may improve the
reception.
Radio frequency interference
This interference produces moving ripples
or diagonal streaks, and in some case, loss of
contrast in the picture. Find out and remove the
radio interference source.
•
•
•
•
10 Troubleshooting
This section describes commonly-encountered
issues and accompanying solutions.
Some problems you encounter with your TV
can be corrected by consulting the following list:
No picture, no sound
1 Check if the fuse or circuit breaker works.
2 Plug another electrical device into the
outlet to make sure it works or is turned
on.
3 Power plug is in a bad contact with the
outlet.
4 Check the signal source.
No color
1 Change the color system.
2 Adjust the saturation.
3 Try another program. Black-white program
may be received.
Remote control does not work
1 Change the batteries.
2 Batteries are not installed correctly.
3 Main power is not connected.
No picture, normal sound
1 Adjust the brightness and contrast.
2 Broadcasting failure may happen.
Normal picture, no sound
1 Press the VOLUME + button to increase
volume.
2 Volume is set to mute, press MUTE to
restore sound.
3 Change the sound system.
4 Broadcasting failure may happen.
Ripples on the picture
Usually caused by local interference such as
cars, daylight lamps and hair driers. Adjust the
antenna to minimize the interference.
Blank screen in VGA(PC) mode
Perhaps the TV can not recognize the resolution
set by the PC. Change to the best resolution or
other standard resolutions of the PC system.
EN
Page 29
29
Connections (Rear)
AV 1: Composite video (CVBS in), Audio
L/R in
YPBPR: Component video (CVI in), Audio
L/R in
PC: VGA in, VGA Audio in
HDMI: 1x
TV: TV ANTENNA
Connections (Side)
Headphone out (stereo mini-jack)
AV1: Composite video (CVBS) in, AUDIO
L/R in
SVIDEO: 1x S-Video in
Power
Mains power: AC 100-240V (±10%)
Power power consumption: 50 W
(19PFL3403), 80 W (26PFL3403)
Standby power consumption: < 0.3 W
Specications are subject to change
without notice. For detailed specications
of this product go to www.philips.com/
support.
Weight
TV weight: 4.2 kg (19PFL3403), 7.7 kg
(26PFL3403)
TV weight with stand: 4.9 kg (19PFL3403),
9.1 kg (26PFL3403)
Dimensions
TV dimensions:
Height: 35.3 cm (19PFL3403), 45.8 cm
(26PFL3403)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
11 Product
information
Note
Product information is subject to change without prior
notice.
•
Supported display resolutions
Computer formats (see ‘Supported screen
resolutions’ on page 23)
Video formats (see ‘Supported screen
resolutions’ on page 24)
Tuner/Reception/
Transmission
Antenna input: 75ohm coaxial (IEC75)
TV system:
Video playback: NTSC, PAL
Sound
Sound system:
Mono/Stereo/SAP
Power output:
2 x 3W (19PFL3403)
2 x 5W (26PFL3403)
Remote control
Type: PF05L08B
Batteries: 2 x AAA size (LR03 type)
•
•
•
•
•
•
•
•
•
•
•
•
En glish
EN
Page 30
30
Width: 47.3 cm (19PFL3403), 67.1 cm
(26PFL3403)
Depth: 6.9 cm (19PFL3403), 9.0 cm
(26PFL3403)
TV dimensions with stand:
Height: 39.4 cm (19PFL3403), 50.3 cm
(26PFL3403)
Width: 47.3 cm (19PFL3403), 67.1 cm
(26PFL3403)
Depth: 16.0 cm (19PFL3403), 21.5 cm
(26PFL3403)
This information is correct at the time of press.
For updated contact information, refer to www.
philips.com/support.
•
•
•
•
•
•
EN
Page 31
31
Page 32
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number:
Loading...