Philips 14RF50S, 14RF50S99 Quick start guide

TABLE OF CONTENTS

Getting Started

Warning/Important Notice . . . . . . . . . . . . .1

Basic Cable Television Connection . . . . . . .1

Basic Antenna Television Connection . . . . . . . . . . . .1

Basic VCR/Accessory Device Connection . . . . . . . .1

Basic Television Operation . . . . . . . . . . . . . . . . . . . .2

Basic Remote Control Operation . . . . . . . . . . . . . . .2

Setting your TV for the first time . . . . . . . . . . . . .3-4

Using the On-screen menu . . . . . . . . . . . . . . . . . . . .3

Using the Language Control . . . . . . . . . . . . . . . . . .3

Setting the Tuner Mode Control . . . . . . . . . . . . . . .3

How to Automatically Program Channels . . . . . . . .4

How to Add and Delete Channels . . . . . . . . . . . . . .4

Quick Use and Setup Guide

BASIC TELEVISION CONNECTIONS

Quick Use and Setup Guide

IMPORTANT

NOTE: This owner's manual is used with several
different television models. Not all features (and
drawings) discussed in this manual will necessar­ily match those found with your television set.
This is normal and does not require you contact­ing your dealer or requesting service.

WARNING: TO PREVENT FIRE OR SHOCK
HAZARD DO NOT EXPOSE THIS UNIT TO
RAIN OR EXCESSIVE MOISTURE.

3139 125 29461

Y

our Cable TV input into

your home may be a
single (75 ohm) cable, or a
Converter Box installation.
In either case the connec­tion to the TV is very easy.
Just put the threaded end
of the cable signal to the
TV's antenna plug and
screw it down finger tight.

CABLE TV

CABLE INPUT/CONVERTER

T

he basic Antenna, or

Cable TV, to VCR to
TV connection is shown to
the right. For more infor­mation on other hookups
(possible when Cable
Converter/Descrambler
boxes are included) refer to
your accessory VCR and
Cable Converter Owner's
Manual for details.

TV TO VCR

BASIC CONNECTION

If your Cable TV signal

is a single round cable (75

ohm) then you're ready to con­nect to the TV.

If you have a Cable
Converter Box:

Connect the Cable TV signal to
the Cable Signal IN(put) plug
on the Converter.

Connect the Cable TV cable to

the ANTENNA/CABLE plug on the TV.

If you have a Cable Converter Box:

Connect the OUT(put) plug from the
Converter to the 75Ω plug on the TV.

Connect your
Antenna or Cable TV signal
to the IN FROM ANT(enna)

plug on the VCR.

Connect the OUT TO

TV plug on the VCR to the
75Ω plug on the TV (connect-

ing cable supplied with the
VCR.)

Back of TV

Round Cable

75Ω Ohm

Cable TV Converter

Box Connection

Cable TV Company

Remember:
Set the TV for the
type signal you've
just connected (see
the “Tuner Mode”
section on page 3 of
this Set-Up Guide.)

To select only the
channel numbers on
your Cable system
see “Auto Program"
(page 4). If you use a
Cable Converter box,
set the TV to the
same channel as the
converter's CH 3/4
switch (on the rear of
the converter.)

SMART

HELP

Cable TV Signal Input

Round Cable

75Ω Supplied with VCR

Outdoor

VHF/UHF

Antenna

300 to 75Ω

Ohm Adapter

Cable TV signal

Back of TV

Refer to the Owner's

Manual included with your

VCR for other possible con­nections and TV/VCR operat­ing details.

OR

NOTE: The connecting cable
for the Converter is supplied
from the Cable TV Company.

VCR

A

combination antenna

receives normal broad­cast channels (VHF 2-13
and UHF 14-69). Your
connection is easy since
there is only one 75Ω
(ohm) antenna plug on the
back of your TV - and
that’s where the antenna
goes.

ANTENNA

COMBINATION UHF/VHF

Remember,
be sure to set the TV
for the type signal
you've connected
(see the “Tuner
Mode” section on
page 3 of this Set­Up Guide.)

To set the TV to
select only the chan­nel numbers in your
area see how to
“Program" or "Add"
channels in memory
on page 4 (Auto
Program section).

To order any option­al accessory contact
your dealer or call
the toll-free accesso­ry ordering number

(1-800-851-8885).

SMART

HELP

If your antenna has a

round cable (75 ohm) on the end,

then you're ready to connect it to
the TV.

If your antenna has flat twin-lead
wire (300 ohm), you first need to

attach the antenna wires to the
screws on a 300 to 75 ohm adapter.

Push the round end of the

adapter (or antenna) onto the
75Ω plug on the rear of the TV.
If the round end of the antenna
wire is threaded, screw it down
finger tight.

300 to 75Ω

Adapter

Combination VHF/UHF

Antenna

(Outdoor or Indoor)

Twin Lead

Wire

Round Cable

75Ω

Back of TV

OR

Note: For homes with separate UHF and VHF
antennas you will need an optional combiner
to connect to the TV.

75 V

VIDEO
L/
Mono

AUDIO

R

Monitor out

AV1 in

S-VIDEO

U/V

Combiner

75-300 Ohm Adapter

Back of TV

12

1

11

2

10

3

9

4

8

5

7

6

2

IN

OUT

75 V

1

Monitor out

AV1 in

VIDEO

L/

Mono

S-VIDEO

AUDIO

75 V

R

1

75 V

2

75 V

Monitor out

AV1 in

VIDEO

L/

Mono

S-VIDEO

AUDIO

R

OR

IN FROM ANT.

1

OUT TO TV

2

75 V

Monitor out

AV1 in

VIDEO

L/

Mono

S-VIDEO

AUDIO

75 V

R

2

BASIC TV AND REMOTE CONTROL OPERATION

TELEVISION

T

o load the supplied batteries into the remote:

1. Remove the battery compartment
lid on the back of the remote.

2. Place the batteries (2-AA) in the
remote. Be sure the (+) and (-) ends of

the batteries line up correctly (inside of
case is marked).

3. Reattach the battery lid.
Slide the TV/VCR/ACC Switch

on the remote control to the TV posi-

tion, then point the remote at the

remote sensor window when operating
the TV with the remote control.

Press the Power but-

ton to turn the TV ON.

Press the Volume + or –

buttons to increase or decrease

the TV sound. Press both at the
same time to display the TV’s
on-screen menu

Press the CH or but-

tons to select TV channels.

These buttons can also be used to
make adjustments or selections
within the on-screen menu.

REMOTE - BATTERIES/OPERATION

Remote Sensor Window is
located on the front of the TV.

QUADRA SURF Buttons - (Red, Green,
Yellow, Blue)Allows you to store and

surf up to 10 channels you choose for
each colored button.

SMILEY Button - Press to add channels
in the “Quadra Surf” lists. Works with all
colored buttons.

TV/VCR/ACC MODE

SWITCH - Slide

to position of TV to control TV functions,
VCR to control VCR functions and ACC
for Cable Converter, DBS, DVD, etc.,
functions.

AUTO SOUND Button - Press repeatedly
to choose from different factory pre­defined sound settings. Choose from
Personal (how you set the Sound Menu
options), Voice (for programming with
speaking only), Music (for musical type
programs such as concerts), or Theatre
(used when watching movies).

MENU Button - Press to display the on­screen menu. Also can be used to back out
of the on-screen menu until it disappears
from the TV’s screen.

VOL(ume) + or – Buttons - Press the
VOL + button to increase the TV’s sound
level. Press the VOL – button to decrease
the TV’s sound level.

MUTE Button - Press the mute button to
eliminate the sound being heard from the
TV. “MUTE” will be displayed on the
TV’s screen. Press again to restore the
TV’s volume to it’s previous level.

CLOCK(TV/VCR) Button - Press to dis­play the “Timer” menu when in the TV
mode. Within this menu set the time, set
the TV to tune to a certain channel at a
certain time once, or daily. When in the
VCR Mode, press to toggle between VCR
viewing and TV viewing.

•

(VCR Record) Button - Press to start a

VCR recording of a TV program.

CC Button

- Press to activate the Closed

Captioning options. Repeatedly press the
CC button will scroll the options available
on the TV screen.

POWER button - Press the Power button
to turn the TV on or off.

FROWNIE Button - Allows you to delete
stored channels within the “Quadra Surf”
lists for the colored buttons.

AUTO PICTURE Button - Press repeat­edly to choose from 5 different factory pre­defined picture settings. Choose from
Personal (how you set the Picture Menu
adjustment controls), Movies (when watch­ing movies), Sports (for any sporting
event),Weak Signal (used when the signal
being received is not the best), or Multi
Media (used for video gaming).

STATUS/EXIT Button - Press to display
the current channel number. If the on­screen menu is displayed, press the
Status/Exit button will remove it from the
TV’s screen.

CURSOR ©, §§, ©©, or n Buttons -

Press to navigate, select and adjust controls
within the on-screen menu after the Menu
button is pressed. These buttons also can be
used with a VCR and when the
TV/VCR/ACC Switch is in the VCR posi­tion. Press the to PLAY ©, REWIND §§,
FASTFORWARD ©©, or STOP ■ the
viewing of a prerecorded video tape.

CH(annel) + or – Buttons - Press to select
channels in ascending or descending order.

SLEEP Button - Press the Sleep button to
set the TV to automatically turn itself off
after a set period of time. Press repeatedly
to select 15, 30, 45, 60, 90, 120, 180, 240
minutes.

PAUSE Button - Press to pause the view­ing of a prerecorded video. The picture will
freeze on the screen until the Play or Pause
buttons are pressed again.

NUMBERED (0-9) Buttons - Press the
numbered buttons to select TV channels or
to enter certain values within the on-screen
menu. For single channel entries, press the
numbered button for the channel you
desire. the TV will pause for a second or
two before changing to the chosen channel.

A/CH Button - (Alternate Channel) Press
to toggle between the last view channel and
the channel presently being viewed.

You can press any

button on the front of

the TV to turn the TV ON.
The tuned channel number

will always briefly appear
when the TV is first turned
ON (and with channel
changes).

SMART HELP

Battery
Compartment
Lid

The remote's TV/VCR/ACC
Switch controls how buttons

on the remote are used.
For example:

With the switch in the "TV"
position:

the Menu, CURSOR ©,

©©

, §§ and ■ buttons

are used to select and
adjust on-screen TV
features.

With the switch in the
"ACC" position:

the Power, Channel
Number, and Channel
Up (+) /Down (–) buttons
on the remote work with
Cable TV Converters.

With the switch in the
"VCR" position:

the Menu, CURSOR

©,

©©

, §§ and ■ buttons

on the remote work Stop,
Play, Fast Forward, and
other VCR features.

Note: For more details on
how the TV remote works
with VCRs and Cable
Converters, see the other
owner's manual supplied with
your TV.

TV/VCR/ACC MODE

SWITCH

Just a couple of

reminders about the
STATUS/EXIT button; you
can press the STATUS/EXIT
button (on the remote) to see
what channel the TV is ON,
what sound mode (stereo or
mono) is present or to
remove the on-screen menu
from the TV’s screen at any
time.

SMART HELP

Front A/V Inputs for quick and
easy accessory hookups.

Headphone Jack

“Flip-up” Door (Front Controls)

AUDIOVIDEO L R

1

INSTALL/MENU

– VOLUME +

CHANNEL

2

3

4

VOL

VOL

VOL

Main

Picture
Sound
Features
Install

Brightness
Color
Picture
Sharpness
Tint
More...

1

2

3

4

4

5

6

2

Main

Picture
Sound
Features
Install

Language
Tuner Mode
Auto Program
Channel Edit

Install

Language
Tuner Mode
Auto Program
Channel Edit

English

Instaler

Idioma
Sintonia
Auto Programa
Editar Canal

Espa ol

SETTING UP YOUR TELEVISION FOR THE FIRST TIME

F

or our Spanish speaking

TV owners an on-screen
LANGUAGE option is pres­ent. With the LANGUAGE
control you can set the TV’s
on-screen menu to be shown
in either English or Spanish.

LANGUAGE

Press the MENU but-

ton on the remote to show the

on-screen menu.

Press the CURSOR UP

© or DOWN ■ buttons to

scroll through the on-screen
menu until the word INSTALL
is highlighted.

Press CURSOR UP © or

DOWN ■ buttons to scroll the

Install features until the word

LANGUAGE is highlighted.

Press the CURSOR
RIGHT ©© button repeat­edly to select ENGLISH or
ESPANOL (Spanish

Press the CURSOR

RIGHT ©© button to display

the INSTALL menu features.

Remember: The Language

control only makes the TV’s on­screen MENU items appear in English
or Spanish text.

It does not change the other on-screen
text features such as Closed Caption
(CC) TV shows.

SMART HELP

Main

Picture
Sound
Features
Install

Brightness
Color
Picture
Sharpness
Tint
More...

Main

Picture
Sound
Features
Install

Language
Tuner Mode
Auto Program
Channel Edit

Install

Language
Tuner Mode
Auto Program
Channel Edit

English

Antenna

Install

Language
Tuner Mode
Auto Program
Channel Edit

English

Cable

Install

Language
Tuner Mode
Auto Program
Channel Edit

English

Auto

VOL

1

2

3

4

4

5

6

2

T

he TUNER MODE con-

trol allows you to change
the TV’s signal input to either
ANTENNA, CABLE or AUTO
mode. It’s important for the
TV to know what type of sig­nal to look for. (From a
Cable TV signal or a normal
Antenna signal.) In the
AUTO mode, when the AUTO
PROGRAM feature is activat­ed, the TV will automatically
choose the correct mode.

TUNER MODE

Press the MENU but-

ton on the remote to show the

on-screen menu

Press the CURSOR UP

© or DOWN ■ buttons to

scroll through the on-screen
menu until the word INSTALL
is highlighted.

Press the CURSOR

RIGHT ©

© button to select

either ANTENNA, CABLE,
or AUTO mode.

Press the CURSOR
RIGHT ©© button to display
the INSTALL menu features.

Press CURSOR UP © or

DOWN ■ buttons to scroll the

Install features until the words
TUNER MODE is highlighted

When CABLE is selected, channels 1-125 are

available. When ANTENNA is selected, channels

2-69 are available.

When AUTO is selected, the TV will automatically set
itself to the correct mode based on the type of signal it
detects when the AUTO PROGRAM feature is activated.

SMART HELP

3

When finished, press

the STATUS/EXIT button to

remove the menu from the
TV’s screen.

When finished, press

the STATUS/EXIT button to

remove the on-screen menu
from the TV’s screen.

F

eatures for your televi-

sion can be adjusted from
within a MENU shown on the
TV’s screen. A MENU is
nothing more than an 0n­screen list of features. Some
of the features have sub­menus but each MENU item
can be adjusted or activated
(deactivated) by viewing the
screen and simply pressing
the proper button.

MENU

Press the MENU but-

ton on the remote or the

Install/Menu buttons (Volume
+, –) on the TV simultaneously
to show the on-screen menu.

Press the CURSOR UP

© or DOWN buttons on the

remote (or the Volume +, – but­tons on the TV) to pick any of
the on-screen menu features.

Press the

STATUS/EXIT button on the

remote to clear the menu from
the screen after an adjustment.

You can also just wait a few
seconds after you finish the
feature adjustment and the
menu will disappear from the
screen automatically.

Press the CURSOR
RIGHT ©© or LEFT §§
buttons on the remote (or

Channel or buttons on
the TV) to adjust any highlight­ed on-screen feature.

If you pass the feature

you want, press the MENU
button on the remote to move
back through the MENU one full
menu screen at a time.

The MENU has a list of features,
some with sub-menus. All the on­screen menu feature can be
adjusted or activated (deactivat­ed).

The on-screen menu will time out
and disappear from the screen
when you finish, or you can press
the STATUS/EXIT button to clear
the menu from the screen.

SMART HELP

Picture Menu

Sound Menu

Features Menu

Install Menu

Main

Picture
Sound
Features
Install

Brightness
Color
Picture
Sharpness
Tint
More...

Main

Picture
Sound
Features
Install

Treble
Bass
Balance
AVL
Incr. Surround
More...

Main

Picture
Sound
Features
Install

Timer
AutoLock

Main

Picture
Sound
Features
Install

Language
Tuner Mode
Auto Program
Channel Edit

1

3

VOL

2

2

4

3

Main

Picture
Sound
Features
Install

Brightness
Color
Picture
Sharpness
Tint
More...

Main

Picture
Sound
Features
Install

Language
Tuner Mode
Auto Program
Channel Edit

Install

Language
Tuner Mode
Auto Program
Channel Edit

Program No.
Skipped

Channel Edit

Program No.
Skipped

12

Channel Edit

Program No.
Skipped

On

Channel Edit

Program No.
Skipped

Off

VOL

1

2

3

4

4

5

9

2

6

7

8

C

hannel Edit makes it

easy for you to ADD or
DELETE channels from the
list of channels stored in the
TV’s memory.

CHANNEL EDIT

Press the MENU but-

ton on the remote to show the

on-screen menu.

Press the CURSOR UP

© or DOWN ■ buttons to

scroll through the on-screen
menu until the word INSTALL
is highlighted.

Press the CURSOR UP

© or DOWN ■ buttons to

scroll the Install features until
the words CHANNEL EDIT
are highlighted.

Press the CURSOR
RIGHT ©© button to display
the CHANNEL EDIT options.

Press the CURSOR
RIGHT ©© button to display
the INSTALL menu features.

With the CHANNEL
EDIT options displayed, and
PROGRAM NO. highlighted;

enter the channel number
(with the NUMBERED or the
CH + or – buttons) you wish
to add (Skipped OFF), or
delete (Skipped ON) from the
TV’s memory.

Scroll down (using the

CURSOR DOWN ■ button)

to highlight the word

SKIPPED.

SETTING UP YOUR TELEVISION FOR THE FIRST TIME

4

Now use the CURSOR
RIGHT ©© button to toggle
between ON or OFF.
If ON is selected the channel

is skipped when scrolling
channels with the CH + or –
buttons. If OFF is selected the
channel is not skipped when
scrolling channels with the CH
+ or – buttons.

When finished, press

the STATUS/EXIT button to

remove the menu from the
TV’s screen.

Y

our TV can automatically

set itself for local area
(or Cable TV) channels. This
makes it easy for you to
select only the TV stations in
your area when the CHAN­NEL (+), (–) buttons are
pressed.

Note: Make sure the antenna
or cable signal connection
has been completed before
AUTO PROGRAM is activat­ed.

AUTO PROGRAM

Press the MENU but-

ton on the remote to show the

on-screen menu.

Press the CURSOR UP

© or DOWN ■ buttons to

scroll through the on-screen
menu until the word INSTALL
is highlighted.

Press the CURSOR
RIGHT ©© button to display
the INSTALL menu features.

Press CURSOR UP © or

DOWN ■ buttons to scroll the

Install features until the words
AUTO PROGRAM are high­lighted.

Press the CURSOR

RIGHT ©© button to start

the Auto Program scanning of
channels. Auto Programming
will store all available chan­nels in the TV’s memory then
tune to the lowest available
channel when done.

Try it out. Press the CHANNEL (+), (–)

buttons and see which channels have been

added to the TV’s memory.

If you want to delete any unwanted channels from the
TV’s memory, refer to the section on adding and remov­ing channels (Channel Edit) on the next page.

SMART HELP

Auto Program will scan for all
available channels within the
Antenna/Cable signal. When
finished, the TV will go back
to the INSTALLmenu.

When finished, press the

STATUS/EXIT button to

remove the menu from the
TV’s screen.

1

Main

Picture
Sound
Features
Install

4

2

Brightness
Color
Picture
Sharpness
Tint
More...

Main

Picture
Sound
Features
Install

Language
Tuner Mode
Auto Program
Channel Edit

Install

Language
Tuner Mode
Auto Program
Channel Edit

Auto Program

Channel

12

VOL

2

4

6

3

5