Peugeot 107 2007 Owner Manual

10

FAMILIARISATION

When this block flashes,
accompanied by an audible
signal, you have enough
fuel left to drive approxi­mately 30 miles (50 km).

FILLING THE FUEL TANK

After opening the flap, insert the key,
turn it slightly to the left then return to
the right. The key returns to its initial
position and the cap is unlocked.

OPENING THE BONNET

1. Internal control.

2. External control.

3. Bonnet strut.



62



50

Low fuel level

Remove the key and unscrew the
cap.

After filling the fuel tank, screw the
cap back on fully to the right until it
clicks and close the flap.

Fuel tank capacity: approximately
35 litres.

11

FAMILIARISATION

WIPERS STALK

Rear wiper and wash-wipe

Ring C

LIGHTS STALK

Lights off.

Side lights.

Dipped headlamps /
Main beam headlamps.

Rear fog lamp

Ring B



51



52

Front and rear lights

Ring A

Windscreen wipers

MIST Single wipe.
OFF Off.
INT Intermittent wipe.
LO Normal wipe (moderate rain).
HI Rapid wipe (heavy rain).

12

FAMILIARISATION

HEATING

Temperature

adjustment

Air flow adjustment

Air distribution

adjustment

Rear screen

demisting



32

AIR CONDITIONING

Temperature

adjustment

Air recirculation /

Air intake

Air distribution

adjustment

Air conditioning

On / Off



33

Air flow adjustment

Rear screen

demisting

13

FAMILIARISATION

I require...

Heating or Manual air conditioning

Air distribution Air flow

Air recirculation /

Intake of exterior air

Temperature Manual AC

HOT

COLD

DEMISTING

DE-ICING

RECOMMENDED INTERIOR SETTINGS

14

FAMILIARISATION

"2 TRONIC" GEARBOX

EASY mode
(automatic mode)

Select position E using the gear
lever.

The gear engaged is displayed on
the instrument panel screen.

The gearbox continuously selects
the most suitable gear.



61

Manual mode

Place the gear lever in position M,
then change up or down through the
gears by pressing:

- rearwards, "+" to change up,

- forwards, "-" to change down.
The gear engaged is displayed on
the instrument panel screen.



61

Starting the vehicle

With the handbrake applied, press
the brake pedal then select position
N to start the engine.

With your foot on the brake, select
position R, E or M.

Release the handbrake, take your
foot off the brake pedal, then accel­erate.



60

15

FAMILIARISATION

AUDIO EQUIPMENT



22

On / Off

Selection of the source: CD or

CD changer or auxiliary

Radio source and selection

of the AM / FM wavebands

Clock adjustment: press
for more than 2 seconds

Volume adjustment

Auxiliary socket for portable

equipment (MP3 player, ...)

Increasing of the hours,

increasing of the minutes

16

FAMILIARISATION

INTERIOR LAYOUT

1. Sun visor

Each sun visor has a courtesy mir­ror with a concealing flap and a card
holder.

2. Storage compartments

3. Storage box

4. Storage compartments in the
front doors

Before opening the door, check that
there are no objects protruding from
the tray.

5. Cup holder

6. 12 volt accessories socket
(120 W max)

This is supplied from the accessories
position (1st notch).

7. Storage compartments in the
rear doors

3-door

5-door

1

WARNING LIGHTS AND INDICATORS

17

INSTRUMENT PANEL

1. Total/trip distance recorder zero

reset button

2. Warning lights and indicators

display

3. Direction indicators

4. Speedometer

5. Fuel gauge

6. Total / trip distance recorder

7. Rear fog lamp indicator light

8. Main beam headlamps indicator

light

9. Dipped headlamps indicator
light

REV COUNTER

When approaching the maximum
engine speed, when the rev counter
needle crosses into the red zone, you
must engage the next gear up.

10. "2 Tronic" gearbox gear and
gear lever positions indicator

1

WARNING LIGHTS AND INDICATORS

18

WARNING LIGHTS AND
INDICATORS

Central STOP
warning light

This flashes for a few

seconds each time the
ignition is switched on. Linked with
the warnings :

- "engine oil pressure",

- "coolant temperature",

Stop immediately if this light
comes on with the engine run­ning.

Contact a PEUGEOT dealer.

Engine oil pressure
warning light

This comes on each time
the ignition is switched on

until the engine is started.
If it comes on linked with the STOP

warning light, with the engine run­ning, this indicates that the oil pres­sure is too low.

Stop immediately.

Contact a PEUGEOT dealer.

Coolant temperature
warning light

This comes on for a few
seconds each time the igni-

tion is switched on.
If this warning light comes on, with

the engine running, this indicates
an abnormal increase in the coolant
temperature.

Stop immediately.

Check the coolant level.
To do this, wait until the engine has

cooled before topping up the level.
The cooling system is pressurised.

Anti-lock braking
system (ABS) warning
light

This comes on for a few
seconds each time the ignition is
switched on.

Fixed lighting indicates a malfuncton
of the ABS.

However, the vehicle retains conven­tional braking with assistance.

Contact a PEUGEOT dealer.

Handbrake, low brake

fluid level and braking

system warning light

This comes on each time
the ignition is switched on until the
handbrake is released.

Fixed lighting, with the engine run­ning, indicates one of the following:

- that the handbrake is applied or

has not been released fully, when
the vehicle is moving,

- an excessive drop in the brake fluid

level (if the warning light remains
on even with the handbrake
released),

- a braking system fault.

Stop immediately.

Contact a PEUGEOT dealer.

When checking the level, and
to avoid any risk of scald­ing, unscrew the cap 1/4 of
a turn to allow the pressure
to drop.

When the pressure has dropped,
remove the cap.

Then:
1 - top up, if necessary (see

"Levels").

2 - or, if the level is satisfactory,

contact a PEUGEOT dealer.

1

WARNING LIGHTS AND INDICATORS

19

Electric power
steering warning light

This comes on for a few
seconds each time the

ignition is switched on.
Fixed lighting, when the vehicle is

moving, indicates a malfunction of
the electric steering system.

Contact a PEUGEOT dealer.

Battery charge
warning light

This comes on each time
the ignition is switched on

until the engine is started.
Fixed lighting, with the engine

running, indicates a malfunction.
Contact a PEUGEOT dealer.

Driver's seat belt not
fastened warning
light**

When the ignition is
switched on, the warning light flashes
until the driver fastens his seat belt.

Above a speed of approximately
10 mph (15 km/h), the warning light
flashes accompanied by an audible
signal until the driver fastens his seat
belt.

Air bags warning light

This comes on for a few
seconds each time the
ignition is switched on.

Passenger air bag disarmed

If the passenger air bag is disarmed,
the warning light remains on.

2 Tronic gearbox
warning light

Fixed lighting of this warn-

ing light, with the engine
running, indicates a malfunction of
the 2 Tronic gearbox.

Emission control
system warning light

This comes on each time
the ignition is switched on

until the engine is started.
Fixed lighting, with the engine

running, indicates an emission
control system fault.

Contact a PEUGEOT dealer.

Diesel engine pre-heat
warning light

Wait until the warning
light is switched off before

starting.
If the temperature is sufficient, the

warning light comes on briefly, you
can start without waiting.

Water in diesel filter
warning light*

This comes on for a few
seconds each time the

ignition is switched on.
Fixed lighting, with the engine

running, indicates a risk of damage
to the engine.

Contact a PEUGEOT dealer.

* According to country.

Note: it may also come on
if you run out of fuel (see
"Running out of fuel").

** According to version.

1

WARNING LIGHTS AND INDICATORS

20

DISPLAY

To reset the trip recorder to zero,
when it is displayed, press and hold
button 1.

"2 Tronic" gearbox indicator

Lever in EASY mode

(automatic mode)

"E" is displayed when

this operating mode is

selected.
It is switched off on switching to man-

ual mode.

Lever in manual mode

"M" is displayed when

this operating mode is

selected.
It is switched off on switching to

EASY mode.

"Neutral"

"Reverse"

Total/trip distance recorder

When the ignition is switched on,
the distance recorder selected when
the engine was switched off is dis­played.

Press button 1 to alternate the dis­tance display:

- total with "ODO" displayed,

- trip with "TRIP" displayed.

1

WARNING LIGHTS AND INDICATORS

20

DISPLAY

To reset the trip recorder to zero,
when it is displayed, press and hold
button 1.

"2 Tronic" gearbox indicator

Lever in EASY mode

(automatic mode)

"E" is displayed when

this operating mode is

selected.
It is switched off on switching to man-

ual mode.

Lever in manual mode

"M" is displayed when

this operating mode is

selected.
It is switched off on switching to

EASY mode.

"Neutral"

"Reverse"

Total/trip distance recorder

When the ignition is switched on,
the distance recorder selected when
the engine was switched off is dis­played.

Press button 1 to alternate the dis­tance display:

- total with "ODO" displayed,

- trip with "TRIP" displayed.

1

WARNING LIGHTS AND INDICATORS

21

Operating mode:

1st gear

2nd gear

3rd gear

4th gear

5th gear

"!" warning light

If this warning light comes
on, with the engine running,
this indicates a malfunction
of the "2 Tronic" gearbox.

Contact a PEUGEOT dealer.

Fuel gauge

This indicates the quantity of fuel
available:

- 1/1 and six blocks, the fuel tank is

full.

- R and one block flashing, the fuel

tank is on the reserve.

Low fuel level

When the minimum level in the fuel
tank is reached, the last block flashes
accompanied by an audible signal.

In certain driving conditions and
depending on the engine, the dis­tance which can be travelled with
the fuel remaining may be less than
30 miles (50 km).

You have approximately 5 litres
remaining.

When the frequency of the flashing
increases, you have approximately

3 litres remaining.

At least 5 litres must be
added after running out of
fuel.

Running out of diesel fuel

After running out of fuel,
you can travel a short
distance after 10 pump
repriming operations (see

corresponding section).
After filling the fuel tank (minimum

5 litres), operate the repriming pump
at least 10 times (see corresponding
section).

2

AUDIO EQUIPMENT

22

GENERAL NOTES / ADJUSTMENTS / AUXILIARY SOCKET

On / Off

Selection of the source: auxiliary

(or CD or CD changer)

Clock adjustment: press

for more than 2 seconds /

Access to the audio settings

Volume adjustment

Auxiliary socket for portable

equipment (MP3 player, ...)

Hours adjustment /

Audio settings

Minutes adjustment /

Audio settings

2

AUDIO EQUIPMENT

23

GENERAL FUNCTIONS

On / off

With the ignition key in
the accessories posi-

tion or with the igni­tion on, press this button to switch
the audio equipment on or off.

After the engine has been switched
off, the audio equipment can only
operate for approximately 30 min­utes, to prevent discharging of the
battery.

Press the upper part
of this button several
times in succession to
increase the volume
of the audio equip­ment or the lower
part of this button to
decrease it.

VOLUME ADJUSTMENT

CLOCK ADJUSTMENT

Press this button sev­eral times in succes­sion to gain access

to the bass (BASS),
treble (TREB), front / rear balance
(FAD) and left / right balance (BAL)
settings.

AUDIO SETTINGS

Press this button for
more than 2 seconds,
the clock display
flashes:

AUXILIARY SOCKET

An auxiliary socket
"AUX" is provided for
the connection of port­able equipment (MP3
player, etc.).

When the parameter

is displayed, change

the setting using these

two buttons.

You exit from this mode automati­cally after a few seconds without any
action.

In order to listen to it,
connect your equip­ment then press this
button.

The audio equipment controls ena­ble you to adjust the volume and the
audio settings.

To exit from the AUX source, press
AM/FM.

- to adjust the hours,
press this button,

- to adjust the min­utes, press this but­ton.

Note: set the volume of the
portable equipment to half
volume to avoid saturating

the audio equipment sound.
Then use the audio equipment vol­ume button.

You exit from this mode automati­cally after a few seconds without any
action.

2

AUDIO EQUIPMENT

24

Selection of the AM / FM

(FM1, FM2, FM3) wavebands

Autostore: automatic storing of

6 stations on AM and FM3

TA function on/off: traffic

information priority

Automatic search for a higher

frequency: double press /

Successive tuning in to

the stations

Selection of the type of radio

programme: News, Sports, Talk,

Pop, Classics

AF function on/off:

alternative frequency

Manual search for

a higher frequency

Selection of the stored station /

Storing of a station: press for

more than 2 seconds

Manual search for
a lower frequency

RADIO

2

AUDIO EQUIPMENT

25

Stereo reception

When the audio equipment receives
a station broadcasting in stereo it
automatically transmits stereo sound
and the screen displays "ST". If the
reception conditions deteriorate, the
audio equipment returns to mono
transmission and "ST" is no longer
displayed.

Press one of these
two buttons briefly to
increase or decrease
the frequency dis­played respectively.

If you maintain the
pressure on the button

in the chosen direc­tion, the frequency will be scanned
continuously.

The scan stops when you release the
button.

Manual station searchAutomatic station search

Manual station storing

Selection of the radio source

Selection of a waveband

Press this button.

Press this button twice
to select the next sta­tion.

Press this button
briefly to listen to each station avail­able on the FM waveband for three
seconds. To stop the station scan,
press this button again.

If the traffic information programme
TA is selected, only stations which
broadcast this type of programme
are selected.

Press the button
several times in suc­cession to select the
wavebands FM1,
FM2, FM3 and AM.

Select the required station.
Press one of the buttons "1" to "6"

for more than 2 seconds
An audible signal confirms that the

station has been stored.

2

AUDIO EQUIPMENT

26

Notes on radio
reception

Your audio equipment will

be subjected to phenomena
which do not affect domestic radio
sets. Both MW/LW and FM reception
are subject to various forms of inter­ference. This is no reflection on the
quality of the equipment but is due to
the nature of the signals and the way
in which they are transmitted.

On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.

On FM, interference may be the
result of increasing distance from the
transmitter, deflection of the signal
by obstacles (mountains, hills, build­ings, etc) or of being in an area which
is not covered by a transmitter.

Automatic storing of FM
stations (autostore)

Press this button.
Your audio equipment

automatically stores
the six best transmit-

ters received on AM and FM in your
current location. These stations are
stored on the AM and FM3 wave­bands. The end of the search is sig­nalled by two audible signals.

Recalling stored stations

On each waveband, a brief press on
one of the buttons "1" to "6" recalls
the corresponding stored station.

If it was not possible to find
six transmitters, the remain­ing memories remain empty:

three dashes are displayed
on the audio equipment screen for
each empty memory.

2

AUDIO EQUIPMENT

27

RDS

Using the AF (alternative
frequency) function on the FM
waveband

Regional following
mode (REG)

This enables you to listen to sta­tions which broadcast a type of pro­gramme which has a theme (NEWS,
SPORTS, TALK, POP, CLASSICS).

Search by type of
programme (PTY)

EON system

This system links stations which
belong to the same network. It per­mits the transmission of traffic infor­mation broadcast by a station which
belongs to the same network as the
station to which you are listening.

In order to benefit from this, select the
traffic information programme TA.

The RDS (Radio Data System) ena-
bles you to continue listening to the
same station irrespective of the fre­quency that it uses in your current
location. The audio equipment con­tinuously searches for the transmitter
which provides the best reception.

Some stations, organised in a
network, broadcast regional pro­grammes in the various regions
which they serve. The regional fol­lowing mode enables you to contiue
listening to the same programme.

Press this button sev­eral times in succes­sion to activate or deac­tivate the function.

On FM, the multifunction display will
indicate:

- "TP" or "TP EON" : the radio trans-

mits a programme while awaiting
the broadcasting of traffic informa­tion.

- "TA" or "TA EON" : the programme

transmitted by the radio is put on
standby while awaiting the broad-

casting of traffic information.
If you wish to interrupt the transmis­sion of a message, press this button
again.

Traffic information
programme (TA)

Press this button
several times in suc­cession to activate or
deactivate the func­tion.

The screen will indicate:

- "AF" if the function is activated,

- "AF REG" if the function is acti-

vated at regional level,

- "AF" flashing if the function is not

available.

When FM is selected,
press this button:

- "no pty" is displayed,

- then press the button briefly to

select a programme.
After a few seconds without any
action, your selection is stored.

Notes: the volume of the traf­fic information is independ­ent of the volume of normal
radio listening.

You can adjust it using the

volume button, when the TA pro-
gramme is being transmitted.

The setting will be stored and will be
used during subsequent message
transmissions.

2

AUDIO EQUIPMENT

28

CD eject

Selection of the source:

CD or CD changer or auxiliary

Selection of the next track

Playing of the start of each

track on the CD: brief press

 : accelerated forwards play
 : accelerated backwards play

Selection of the previous track

Random playing of the tracks on

the CD currently being played

CD changer:

 : selection of the previous CD
 : selection of the next CD

CD: repeating of the current track /

CD changer, press for more than 2 seconds:

repeating of the current CD

CD PLAYER OR CD CHANGER

2

AUDIO EQUIPMENT

29

Press this button to
select the next track.

Press this button to
return to the start of
the current track or
to select the previous
track.

CD PLAYER AND CD
CHANGER FUNCTIONS

Selection of a track on a CD

Introscan (SCAN)

Press this button to
listen to the start of
each track on the cur­rent CD.

Accelerated play

Press and hold one
of these buttons for
accelerated forwards
or backwards play
respectively.

The accelerated play
stops when the button
is released.

When a CD is inserted,
printed face upper­most, play begins
automatically.

If there is a CD in the player already,
press this button.

CD PLAYER FUNCTIONS

Selection of the CD player

Repeating of a track on the
CD (RPT)

Random playing of the CD
(RAND)

When the CD player
is selected, press this
button.

If you wish to listen
to the current track
again, press this but­ton. To cancel the rep-

etition, press the button again.

CD eject

Press this button to
eject the CD from the
player.

The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.

The random play mode is deacti­vated when the audio equipment is
switched off.

The use of copied CDs may
cause faults.

Insert circular CDs only.

2

AUDIO EQUIPMENT

28

CD eject

Selection of the source:

CD or CD changer or auxiliary

Selection of the next track

Playing of the start of each

track on the CD: brief press

 : accelerated forwards play
 : accelerated backwards play

Selection of the previous track

Random playing of the tracks on

the CD currently being played

CD changer:

 : selection of the previous CD
 : selection of the next CD

CD: repeating of the current track /

CD changer, press for more than 2 seconds:

repeating of the current CD

CD PLAYER OR CD CHANGER

2

AUDIO EQUIPMENT

29

Press this button to
select the next track.

Press this button to
return to the start of
the current track or
to select the previous
track.

CD PLAYER AND CD
CHANGER FUNCTIONS

Selection of a track on a CD

Introscan (SCAN)

Press this button to
listen to the start of
each track on the cur­rent CD.

Accelerated play

Press and hold one
of these buttons for
accelerated forwards
or backwards play
respectively.

The accelerated play
stops when the button
is released.

When a CD is inserted,
printed face upper­most, play begins
automatically.

If there is a CD in the player already,
press this button.

CD PLAYER FUNCTIONS

Selection of the CD player

Repeating of a track on the
CD (RPT)

Random playing of the CD
(RAND)

When the CD player
is selected, press this
button.

If you wish to listen
to the current track
again, press this but­ton. To cancel the rep-

etition, press the button again.

CD eject

Press this button to
eject the CD from the
player.

The tracks on the CD will be played
in a random order. Press the button
again to return to normal play.

The random play mode is deacti­vated when the audio equipment is
switched off.

The use of copied CDs may
cause faults.

Insert circular CDs only.

2

AUDIO EQUIPMENT

30

Press this button.

CD CHANGER FUNCTIONS

Selection of the CD changer

Random playing of a CD
(RAND)

When the CD changer
is selected, press this
button for 2 seconds.

The tracks of the
current CD will be played in a random
order.

Press the button again for 2 seconds
to return to normal play.

Selection of a CD

Press one of these
buttons on the audio
equipment to select
the previous or next
CD respectively.

Repeating of a CD (RPT)

If you wish to listen to
the current CD again,
press and hold this
button.

The use of copied CDs may
cause faults.

Insert circular CDs only.

To cancel the repetition, press the
button again.

3

COMFORT

31

VENTILATION

Recommendations for
use

If the interior temperature

remains very high after a
prolonged period parked in the sun,
do not hesitate to ventilate the pas­senger compartment for a few min­utes.

For an even air distribution, make
sure that you do not block the out­side air inlet grille, the vents, the air
passages and the air outlets to the
footwells.

Ensure that the passenger compart­ment filter, located below the wind­screen, in the engine compartment,
is in good condition. Have the filter
elements replaced regularly. If you
drive in dusty conditions, change
them twice as often.

Operate the air conditioning system
for 5 to 10 minutes, once or twice a
month, to keep it in perfect working
order.

In order to ensure that your air condi­tioning system continues to operate
correctly, you are advised to have it
checked regularly.

The condensation created by the air
conditioning results in a flow of water
under the vehicle when stationary
which is perfectly normal.

If the system does not produce cold
air, do not use it and contact your
PEUGEOT dealer.

3. Side vents.

4. Diffusion grille.

5. Air outlets to the footwells.

1. Windscreen de-icing or

demisting vent.

2. Side window de-icing or

demisting vents.

The air conditioning system

does not contain chlorine

and does not present any

danger to the ozone layer.

3

COMFORT

32

HEATING

1. Temperature adjustment

Turn the control from blue (cold) to
red (hot) to adjust the temperature to
suit your requirements.

2. Air flow adjustment

When the ignition is switched on,
turn the control to obtain a flow of
air which is sufficient to ensure your
comfort.

To maintain a certain level of comfort
in the passenger compartment, avoid
position 0 whenever possible.

In position 0, a slight flow of air, due
to the movement of the vehicle, can
still be felt.

The air distribution can be

adjusted by placing the con-

trol in an intermediate posi-

tion.

Footwells.

4. Rear screen demisting

With the engine running,
press button 4, the indica­tor light comes on.

The system demists the
rear screen.

It is switched off by pressing
control 4.

Windscreen, side windows
and footwells.

Footwells, diffusion grille
and side vents.

Diffusion grille and side
vents.

3. Air distribution adjustment

Windscreen and side
windows.

Switch the system off as

soon as you consider this

necessary as a lower con-

sumption of current reduces
fuel consumption.

De-icing and demisting

To quickly de-ice or demist the wind­screen and side windows:

- set the air distribution to "Windscreen

and side windows",

- place the tem

perature control 1 and

the air flow control 2 at maximum,

- close the side

vents.

3

COMFORT

33

1. Air conditioning On/Off

With the engine running,
press the button, the indi­cator light comes on.

1. Air conditioning On/Off

2. Temperature adjustment

3. Air flow adjustment

AIR CONDITIONING

2. Temperature adjustment

Turn the control from blue (cold) to
red (hot) to adjust the temperature to
suit your requirements.

4. Air recirculation / Air intake

5. Air distribution adjustment

6. Rear screen demisting

3. Air flow adjustment

When the ignition is switched on,
turn the control to obtain a flow of
air which is sufficient to ensure your
comfort.

To maintain a certain level of comfort
in the passenger compartment, avoid
position 0 whenever possible.

In position 0, a slight flow of air, due
to the movement of the vehicle, can
still be felt.

The air conditioning will not oper­ate if the air flow adjustment con­trol 3 is in position 0.