1007 Dag 2008
FAMILIARISATION
EXTERIOR
"Follow-me-home" lighting
After switching off the ignition, when
you leave your vehicle, the front lights
remain on briefl y.
88
Rear parking assistance
This equipment warns you if an obstacle is detected behind the vehicle when
reversing.
109
Tyre under-inflation
detection
This equipment monitors the
pressure of each tyre and
warns you of a puncture or
defl ation.
92
"Sesame" sliding doors
This equipment, fi tted with an obstacle
detection system, makes opening and
closing of the doors easier. Operation is
accompanied by and audible signal.
79
FAMILIARISATION
Opening/Closing using the
controls
A. Driver's electric control.
B. Passenger's electric control.
OPENING
Key/remote control
A. Unfolding/Folding of the key.
B. Normal locking or deadlocking
and locating of the vehicle.
C. Unlocking of the vehicle.
D. Opening of the driver's door and
unlocking of the vehicle (if the
vehicle is locked)/Closing of the
driver's door.
E. Opening of the passenger's door
and unlocking of the vehicle (if
the vehicle is locked)/Closing of
the passenger's door.
"Sesame" doors
Opening/Closing using the
handle
1. Exterior manual opening.
2. Exterior manual closing.
79
Press a control to open or close the
corresponding door.
80
72
You are advised to use the
remote control or the controls
as much as possible.
FAMILIARISATION
OPENING
83
85
Boot Fuel tank Bonnet
Locking or unlocking the tailgate
and the doors
The tailgate is locked or unlocked
using the remote control or from the
lock on the driver's door.
To open the tailgate, press control 1
and raise the tailgate.
1. Opening of the fuel fi ller fl ap.
2. Opening and hooking of the fuel
tank cap.
Tank capacity: approximately 40 litres.
A. Interior control.
B. Exterior control.
C. Bonnet strut.
112
FAMILIARISATION
INTERIOR
"Cameleo" interior
This equipment, available in 9 kits
consisting of 18 components each, is
used to personalise and enhance the
passenger compartment.
65
Seat modularity
The design of the seats permits various
layouts and optimises the management
of the interior space of your vehicle.
56
Audio and communication
systems
This equipment benefi ts from the latest
technology: MP3 compatible WIP Sound
audio equipment, Bluetooth hands-free
kit, WIP Com GPS audio/telephone,
JBL audio system, USB socket.
139
FAMILIARISATION
DRIVING POSITION
1. Driver's front air bag.
Horn.
2. Steering column air bag.
3. Steering wheel adjustment.
4. Exterior mirror electric controls.
Headlamp adjustment.
5. Cruise control/speed limiter
switches.
6. "2 Tronic" gearbox steering
wheel controls.
7. Lights and direction indicators
controls.
8. Instrument panel.
9. Gear lever.
10. Window electric control
(driver and passenger).
11. Lighter/12 V socket
(100 W max.).
12. Bonnet release.
13. Fascia fuse box.
14. "Sesame" door electric controls
(driver and passenger).
15. Adjustable and closing side
vent.
FAMILIARISATION
DRIVING POSITION
1. Steering lock and ignition.
2. Audio equipment steering wheel
controls.
3. Wipers/trip computer controls.
4. Adjustable and closing central
vents.
5. Windscreen de-icing and
demisting vent.
6. Multifunction display.
Passenger seat belts
unfastened/not fastened
warning lights.
7. Passenger front air bag.
8. Passenger "Sesame" door
electric control.
9. Glove box/Audio/video sockets/
Disarming of the passenger air
bag.
10. Handbrake.
11. Deactivation of the rear parking
assistance.
Central locking from the inside.
Deactivation of the ESP/ASR
system.
12. USB socket.
13. Deactivation of the interior
alarm or card holder.
14. Heating or air conditioning
controls.
15. WIP Sound audio equipment or
WIP Com GPS audio/telephone.
16. Hazard warning lights.
FAMILIARISATION
SITTING COMFORTABLY
Front seats
1.
Forwards/backwards adjustment.
2. Driver's seat height adjustment.
3. Seat back angle adjustment.
4. Head restraint height and angle
adjustment.
5. Access to the rear seats.
6. Heated seat control.
51
FAMILIARISATION
Interior mirror adjustment Electric exterior mirror
adjustment
1. Selection of the mirror's "day"
position.
2. Directing of the mirror.
A. Control for selection, adjustment
or folding of the exterior mirrors.
B. Selection of the driver's mirror.
C. Central position "
SITTING COMFORTABLY
50
D. Selection of the passenger's
mirror.
E. Folding of the mirrors.
".
50
Front seat belt adjustment
Slide your arm along the door and
grasp the seat belt at the bottom.
Then, insert the tongue in the buckle.
This operation must be carried out
with the door closed to avoid any risk
of trapping.
96
FAMILIARISATION
SEEING CLEARLY
Lighting Wipers
Ring A
Lights off.
Automatic switching on of
the lights.
Side lights.
Dipped headlamps/main
beam headlamps.
Ring B
Rear fog lamps.
or
Front and rear fog lamps.
86
Windscreen wipers
2. Fast wipe.
1. Normal wipe.
I. Intermittent wipe.
0. Park
AUTO. Automatic wipe.
Single wipe.
A. Wash-wipe.
89
Rear wiper
Park.
Intermittent wipe.
Wash-wipe.
90
FAMILIARISATION
I require...
Heating or Manual air conditioning
Air distribution Air fl ow
Air recirculation/
Intake of exterior air
Temperature Manual AC
HOT
COLD
DEMISTING
DE-ICING
VENTILATE
Recommended interior settings
FAMILIARISATION
MONITORING
110
79
95
76
Instrument panel
A. When the ignition is on, the fuel
gauge needle should rise.
B. When the engine is running, its
associated low level warning
light should switch off.
C. When the ignition is on, the oil
level indicator should display
"OIL OK" for a few seconds.
If the levels are not correct, top up
the corresponding level.
18
Warning lights Controls
1.
When the ignition is on, the orange and red warning lights come
on.
2. When the engine is running, these
warning lights should switch off.
If warning lights remain on, refer to
the page concerned.
20
Lighting of the indicator light indicates the status of the corresponding
function.
A. Deactivation of the visual and
audible rear parking assistance.
B. Central Locking/Unlocking.
C. Deactivation of the ESP/ASR
systems.
D.
Deactivation of the interior alarm.
FAMILIARISATION
1. Opening of the glove box.
2. Insertion of the key.
3. Selection of the "OFF" position.
4. Removal of the key keeping the
switch in this position.
1. Stop position.
2. Ignition position.
3. Starting position.
A. Driver's seat belt not fastened
or unfastened warning light, lit in
red.
B. Passenger seat belt not fastened
or unfastened warning light.
1: front.
2: rear right.
3: rear left.
KEEPING YOUR PASSENGERS SAFE
STARTING
Seat belts and air bags Disarming the front
passenger air bag
96
C. Passenger air bag warning light;
lit if the air bag is disarmed.
D. Air bags warning light; off after
the ignition is switched on.
99
Ignition switch
99
FAMILIARISATION
DRIVING SAFELY
Speed limiter Cruise control
1. Speed limiter mode Selection/
Off.
2. Decreasing of the programmed
value.
3. Increasing of the programmed
value.
4. Speed limiter On/Off.
The values must be set with the
engine running.
105
1. Cruise control mode Selection/
Off.
2. Decreasing of the programmed
value.
3. Increasing of the programmed
value.
4. Cruise control On/Off.
In order to be programmed or activat-
ed, the vehicle speed must be above
25 mph (40 km/h), with at least fourth
gear engaged on the manual gearbox (second gear for the "2 Tronic"
gearbox).
107
Display on the instrument panel
The cruise control or speed limiter
mode appears on the instrument
panel when it is selected.
Cruise control
Speed limiter
FAMILIARISATION
DRIVING SAFELY
"2 Tronic" gearbox Display on the instrument
panel
The gear or the mode selected ap-
pears on the instrument panel display.
N: neutral.
R: reverse.
1 2 3 4 5: gears engaged.
Auto: automatic mode.
This fi ve-speed piloted manual
gearbox offers a choice between
the comfort of fully automatic operation or the pleasure of manual gear
changing.
1. Gear lever.
2. "-" steering wheel control.
3. "+" steering wheel control.
Moving off
Select position N and press
the brake pedal fi rmly while
starting the engine.
or A ) or reverse (position R ) using the
gear lever 1 .
Engage fi rst gear (position M
Normal driving
Two driving modes are offered:
- sequential mode for manual
changing of the gears by the
driver,
- automatic mode for automatic
management of the gears
by the gearbox. In automatic
mode, you can take control at
any time by
wheel controls, when overtaking
for example
mode).
using the steering
( auto sequential
102
PETROL MANUAL GEARBOX AND "2 TRONIC" GEARBOX
1. Trip distance recorder zero
reset and total/trip distance
recorder display button.
2. Emission control system
warning light.
3. Service warning light.
4. Anti-lock braking system (ABS)
warning light.
5. Electronic stability control
(ESP/ASR) warning light.
6. Handbrake, brake fl uid level
and electronic brake force
distribution warning light.
7. Maximum coolant temperature
warning light.
8. Engine oil pressure warning
light.
9. Punctured wheel warning light.
10. Battery charge warning light.
11. Left direction indicator.
12. Fuel gauge.
13. Low fuel level warning light.
14. Central STOP warning light.
15. Speedometer.
16. Speed limiter/cruise control
indicator light.
17. Service indicator, engine oil
level gauge and total/trip
distance recorder.
18. "2 Tronic" gearbox indicator.
19. Foot on brake warning light
("2 Tronic" gearbox).
20. Rev counter.
21. Right direction indicator.
22. Dipped headlamps indicator
light.
23. Main beam headlamps indicator
light.
24. Front fog lamps indicator light.
25. Rear fog lamp indicator light.
26. Door open warning light.
27. Seat belt not fastened warning
light.
28. Passenger air bag disarmed
warning light.
29. Front, steering column, side and
curtain air bags warning light.
30. Lighting rheostat button.
DIESEL MANUAL GEARBOX INSTRUMENT PANEL
1. Trip distance recorder zero
reset and total/trip distance
recorder display button.
2. Emission control system
warning light.
3. Service warning light.
4. Anti-lock braking system (ABS)
warning light.
5. Electronic stability control
(ESP/ASR) warning light.
6. Handbrake, brake fl uid level
and electronic brake force
distribution warning light.
7. Maximum coolant temperature
warning light.
8. Engine oil pressure warning
light.
9. Punctured wheel warning light.
10. Battery charge warning light.
11. Left direction indicator.
12. Fuel gauge.
13. Low fuel level warning light.
14. Central STOP warning light.
15. Speedometer.
16. Diesel engine pre-heat warning
light.
17. Water in diesel fi lter warning
light.
18. Speed limiter/cruise control
indicator light.
19. Service indicator, engine oil
level gauge and total/trip
distance recorder.
20. Rev counter.
21. Right direction indicator.
22. Dipped headlamps indicator
light.
23. Main beam headlamps indicator
light.
24. Front fog lamps indicator light.
25. Rear fog lamp indicator light.
26. Door open warning light.
27. Seat belt not fastened warning
light.
28. Passenger air bag disarmed
warning light.
29. Front, steering column, side and
curtain air bags warning light.
30. Lighting rheostat button.
20
WARNING LIGHTS
A permanently lit warning light or one fl ashing, with the engine running, indicates an operating fault of the unit
concerned. The illumination of certain warning lights may be accompanied by an audible signal and a message on
the multifunction display. Do not ignore this warning: consult a PEUGEOT dealer.
If the central STOP warning light comes on when you are driving, stop your vehicle immediately, where it is safe to
do so.
Central STOP
warning light
This comes on for a few
seconds each time the
ignition is switched on.
Linked to the warning lights:
- ''engine oil pressure and temperature'',
- "punctured wheel",
- "maximum coolant temperature",
- "handbrake'', ''low brake fl uid
level'', and ''electronic brake
force distribution''.
You must stop if the light comes
on with the engine running.
Consult a PEUGEOT dealer.
Engine oil pressure and
temperature warning
light
This comes on for a few seconds each
time the ignition is switched on.
Linked to the central STOP warning
light.
If this warning light comes on, with
the engine running, it indicates one
of the following:
- insuffi cient oil pressure,
- a lack of oil in the lubrication circuit.
Top up the level,
- an oil temperature which is too
high. The warning light is accompanied by an audible signal. To
lower the oil temperature, reduce
your speed.
You must stop.
Consult a PEUGEOT dealer.
Service warning light
This comes on for a few seconds each time the ignition
is switched on.
If this warning light comes on, with the engine running, accompanied by an audible
signal and a message on the multifunction display, it indicates the occurrence of
a problem in one of the systems which
does not have a specifi c warning light.
Consult the message on the multifunction display to identify the system
concerned.
Check:
- the remote control battery,
- the pressure of the tyres,
- the engine oil level,
- the screenwash level,
- the condition of the bulbs.
For all other cases, contact a PEUGEOT
dealer.
The lighting of this warning light may
also indicate the start of saturation of
the particle emission fi lter (Diesel),
due to exceptionally prolonged urban
driving conditions: low speed, long
traffi c jams, ...
In order to regenerate the fi lter, you
are advised to drive, as soon as traf-
fi c conditions permit, at a speed of
35 mph (60 km/h) or more for at least
fi ve minutes (until the warning light
switches off).
If the warning light remains on, contact
a PEUGEOT dealer.
21
Punctured wheel
warning light
This comes on for a few
seconds each time the ignition
is switched on.
Linked to the central STOP warning
light.
If this warning light comes on while
the vehicle is moving, it indicates that
one or more wheels are punctured.
It is accompanied by an audible
signal and a message on the multifunction display locating the wheel
concerned.
You must stop.
Change the damaged wheel and
have it repaired by a PEUGEOT
dealer.
Maximum coolant
temperature warning
light
This comes on for a few seconds each
time the ignition is switched on.
Linked to the central STOP warning
light.
If this warning light comes on, with
the engine running, it indicates an
abnormal increase in the temperature of the coolant.
You must stop.
Consult a PEUGEOT dealer.
Anti-lock braking
system (ABS) warning
light
This comes on for a few seconds each
time the ignition is switched on.
If the warning light remains on or
comes on above 8 mph (12 km/h),
this indicates an ABS malfunction.
Electronic stability
control system (ESP/
ASR) warning light
This comes on for a few seconds each
time the ignition is switched on.
While the engine is running and the
vehicle is moving, it fl ashes if the
system is activated.
It comes on permanently when it is
disarmed.
Battery charge warning
light
This comes on for a few
seconds each time the ignition is
switched on.
If it comes on, with the engine running,
it indicates one of the following:
- faulty operation of the charging
circuit,
- slack battery or starter terminals,
- a cut or slack alternator belt,
- an alternator failure.
Consult a PEUGEOT dealer.
Handbrake, low brake
fluid level and Electronic
Brake Force Distribution
warning light
This comes on for a few seconds each time the ignition is
switched on.
Linked to the central STOP warning
light.
If this warning light comes on, with
the engine running, it indicates one
of the following:
- that the handbrake is applied or
not fully released, if the vehicle is
moving,
- an excessive drop in brake fl uid
level (if the warning light remains
on even when the handbrake is
released),
- a fault in the Electronic Brake
Force Distribution.
You must stop.
Consult a PEUGEOT dealer.
However, the vehicle retains conventional servo-assisted braking.
Lighting of this warning light, accompanied by an audible signal, indicates
an ABS fault.
Consult a PEUGEOT dealer.
22
Low fuel level warning
light
This comes on for a few seconds each
time the ignition is switched on.
When this light fi rst comes on, you
have enough fuel to drive approxi-
mately 30 miles (50 km) (The tank
capacity is approximately 40 litres).
Water in diesel filter
indicator
This comes on for a few seconds each
time the ignition is switched on.
If it comes on, with the engine running, this indicates that there is a risk
of damage to the injection system.
Consult a PEUGEOT dealer as soon
as possible.
Diesel engine pre-heat
warning light
Wait until the warning light goes out
before starting the engine.
If the temperature is high enough,
the warning light comes on for less
than one second. You can start the
engine without waiting.
Passenger air bag
disarmed warning light
This comes on for a few seconds each
time the ignition is switched on.
If the passenger air bag is disarmed,
the warning light remains on.
Always consult a PEUGEOT dealer if
the warning light fl ashes.
Seat belt not fastened
warning light
When the ignition is switched
on, this warning light comes
on if the driver (and/or a passenger)
has not fastened his seat belt.
Above 12 mph (20 km/h), this warning
light fl ashes for two minutes accom-
panied by an audible signal which
becomes progressively louder. Once
the two minutes have elapsed, the
warning light remains on until the driver
(and/or passenger) fastens his seat
belt.
The driver must ensure that all
passengers fasten and use the
seat belts correctly.
Door open warning
light
This comes on if a door, the bonnet
or the boot is still open.
Above 6 mph (10 km/h), this warning
light is accompanied by an audible
signal and a message on the multifunction display.
"Foot on brake" warning
light ("2 Tronic" gearbox)
When this warning light comes on,
you must put your foot on the brake
(example: when starting the engine).
If you do not put your foot on the
brake, this warning light fl ashes.
Front, steering column,
side and curtain air
bags warning light
This comes on for a few seconds each
time the ignition is switched on.
With the engine running, illumination
of this warning light, accompanied
by an audible signal, indicates a fault
in the front, steering column, side or
curtain air bags.
Consult a PEUGEOT dealer.
Emission control
system warning light
This comes on each time the ignition
is switched on and remains on until
the engine is started.
If it comes on, with the engine running, it indicates a malfunction of the
emission control system.
Consult a PEUGEOT dealer.
23
INSTRUMENT PANEL
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and
trip distances).
Note: the trip distance is displayed
for thirty seconds, when the ignition is
switched off, on opening and closing
the driver's door as well as on locking
the vehicle.
It also displays the "2 Tronic" gearbox positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approximately 5 seconds after the service indicator display.
Oil level correct
Lack of oil
If "OIL" fl ashes and the service warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display, this indicates
a lack of oil which could damage the
engine.
If the lack of oil is confi rmed by a
check using the dipstick, it is essential
that the level is topped up.
Oil level gauge fault
Check the oil level using the dipstick.
If "OIL --" fl ashes, this indicates a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
The level read on the dipstick
will only be correct if the
vehicle is on level ground
and the engine has been off
for more than 15 minutes.
24
Service indicator
This indicates when the next service
is due in accordance with the manufacturer's servicing schedule.
The point at which the next service
is due is calculated from the last indicator zero reset. It is determined by
two parameters:
- the distance travelled,
- the time which has elapsed since
the last service.
Operation
When the ignition is switched on, the
spanner symbolising the servicing
operations comes on; the distance
recorder display indicates the number
of miles [kilometres] (rounded off)
remaining until the next service.
Example: 4,800 miles/km remain before
the next service. For fi ve seconds after
the ignition is switched on, the display
indicates:
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total or trip
distance.
The distance remaining to
the next service is less than
500 miles/1,000 km.
Example: 400 miles/900 km remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
It indicates that a service must be
carried out soon. The display indicates the total or trip distance.
The service is overdue.
The spanner fl ashes for 5 seconds
each time the ignition is switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
The display indicates the total or trip
distance.
The distance remaining before the
next service may be weighted by the
time factor, depending on the user's
driving habits.
The spanner may also come on if
more than two years have elapsed
since the last service.
25
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you
wish to disconnect the battery, lock the vehicle and
wait for at least fi ve minutes,
otherwise the zero re-set will not be
registered.
Total/trip distance recorder
Briefl y pressing the button alternates
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required brightness, release the button.
26
"2 Tronic" gearbox indicator
"AUTO" indicator light
This comes on when
the "AUTO" automated
operation mode is
selected.
It is switched off on switching to the
sequential operation mode.
It fl ashes if a malfunction occurs.
Gear lever positions:
"Neutral"
"Reverse"
Sequential operating mode
1st gear
2nd gear
3rd gear
4th gear
5th gear
27
TRIP COMPUTER
System which provides current information concerning the route travelled
(range, consumption, ...).
Monochrome display A
Data displays
Press the button, located at the
end of the wipers stalk , to dis-
play the various items of trip
computer data in succession.
The trip computer data is the
following:
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
The next press then returns you
to the normal display.
Zero reset
Press the control for more than two
seconds to reset the distance travelled, the average consumption
and the average speed to zero.
28
the current information
tab with:
the range,
the current
consumption,
the distance
remaining to be
travelled,
Route zero reset
Press the button, located at the
end of the
wipers stalk
, to dis-
play the various trip computer
tabs in succession:
Data displays
When the route required is dis-
played, press the control for
more than two seconds.
the route
tab with:
the di
stance
travelled,
the average
consumption,
the average speed,
for the fi rst r
oute.
the route
tab with:
t
he distance
travelled,
the average
consumption,
the average
speed, for the
second
route.
The routes
"1"
and
"2"
are inde-
pendent but their use is identical.
Route
"1"
permits, for example, daily
calculations, and route
"2"
monthly
calculations.
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption, …).
Monochrome display C
Colour display
29
Distance remaining to be
travelled
(km or miles)
This is the distance remaining to be
travelled to the fi nal destination. It
is either calculated instantly by the
navigation system if guidance is acti-
vated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
(km/h or mph)
This is the average speed cal-
culated since the last trip com-
puter zero reset (ignition on).
Range
(km or miles)
This indicates the number of miles
(or kilometres) which can still be
travelled with the fuel remaining in
the tank in relation to the average
consumption over the last few miles
(kilometres) travelled.
Current consumption
(l/100 km or km/l or mpg)
This is the average quantity of fuel
consumed over the last few seconds.
Average consumption
(l/100 km or km/l or mpg)
This is the average quantity of fuel
consumed since the last trip compu-
ter zero reset.
Distance travelled
(km or miles)
This indicates the distance travelled
since the last trip computer zero reset.
A few definitions…
When the range falls below 20 miles
(30 km), dashes are displayed. After
fi lling with at least 5 litres of fuel, the
range is recalculated and is displayed
when it exceeds 60 miles (100 km).
If dashes are displayed con-
tinuously while driving in
place of the digits, contact a
PEUGEOT dealer.
This function is only displayed
from 20 mph (30
km/h).
This fi gure may increase fol-
lowing a change of driving
style or relief, resulting in a
signifi cant change in the cur-
rent consumption.
30
Press the
"MENU"
button to gain
access to the general menu.
Press the arrows, then the
"OK"
button to select the
"Trip com-
puter"
menu.
On the
"Trip computer"
menu,
select one of the following appli-
cations:
Warnings log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Enter the distance to the
destination
This enables you to enter an approxi-
mate value for the distance to the fi nal
destination.
"TRIP COMPUTER" MENU
System which provides general infor-
mation concerning the status of certain
equipment with which your vehicle is
equipped, such as the warnings log,
the status of the functions...
On the
"Diagnostics"
menu,
select one of the following appli-
cations:
Press the
"MENU"
button to gain
access to the general menu.
Turn the dial and press it to
select the
"Diagnostics"
menu.
Display C
"DIAGNOSTICS" MENU
Colour display
31
MONOCHROME DISPLAY A
(without WIP Sound)
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature (this
fl ashes if there is a risk of ice),
- the status of the accesses
(doors, boot, ...),
- the warning messages (e.g.:
"Antipollution system faulty") or
information messages
(e.g.: "Auto lights on"),
displayed temporarily, can be
cleared by pressing the "ESC"
button,
- the trip computer (see
corresponding section).
Parameter configuration
There are three display control but-
tons:
- "ESC" to abandon the operation
in progress,
- "MENU" to scroll through the
menus or sub-menus,
- "OK" to select the menu or sub-
menu required.
General menu
Press the "MENU" button to scroll
through the various menus of the
general menu:
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
32
Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear,
- "follow-me-home" lighting.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
Display settings
Once the "Display settings" menu
has been selected, you can gain access to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Once you have selected a setting,
press the "OK" button to change its
value.
Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been selected, you can change the units of
the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or
km/l).
Wait for approximately ten seconds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the normal
display.
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.
33
Presentation
This displays the following information,
via the WIP Sound control keypad:
- the time,
- the date,
- the outside temperature (this
fl ashes if there is a risk of ice),
- the audio source displays
(radio, CD, ...),
- the status of the accesses
(doors, boot, ...),
- the warning messages
(e.g.: "Antipollution system
faulty") or information messages
(e.g.: "Auto lights on"),
displayed temporarily, can be
cleared by pressing the "ESC"
button,
- the trip computer
(see corresponding section).
General menu
Press the "MENU" button to gain ac-
cess to the general menu, then press
the " " or " " buttons to scroll
through the following items:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
Radio-CD
With the WIP Sound switched on,
once the "Radio-CD" menu has been
selected, you can activate or deactivate the functions linked with the use
of the radio (RDS following, REG
mode), the CD or the CD changer
(introscan, random play, CD repeat).
Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- rear wiper linked with reverse
gear,
- "follow-me-home" lighting.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
Loading...