Petsafe Magnetic 4-Way Locking Cat Flap User Manual

Magnetic

4-Way Locking

Cat Flap

Installation Guide for Metal Door (Wood Door Installation on Reverse)

Before installing your cat ﬂ ap, please read the following step-by-step instructions carefully

1 2 3

Tools Required

Drill holes at each corner.

Measure the belly height of your cat. This is usually around 4 to 6 inches.

6 7 8

Cut along the lines using a jigsaw.

9 10

248 mm

(9 3/4")

Mark this measurement on the outside of your door and draw a straight horizontal line 6 1/2"

Smooth out the rough edges. Fit a 3 1/2"

Wood Door Installation on reverse. The cat ﬂ ap will not operate if ﬁ tted to a door containing metal e.g. uPVC coated metal doors, metal skin doors, or security doors. The cat ﬂ ap must be isolated from the metal with a piece of wood.

Draw a square 6 1/2" W x 9 3/4" H. Bottom of square should be the horizontal line from step 3.

the hole.

165 mm

(6 1/2")

x 6 1/2"

wooden block to

Place the cat ﬂ ap in the hole, with the red 4-way lock facing inside. Mark the screw holes.

Remove the cat ﬂ ap and drill holes with a 3/16"

13 14

Place collar key on center of tunnel and push ﬂ ap. Do not force ﬂ ap open with magnet in hand. Fit hanging key to your cat’s collar.

Temporarily tape open the cat ﬂ ap. Sometimes it helps for you to be on one side of the door and your pet on the other. Use food or treats to coax your pet through the open door. Let the pet become familiar with passing through. In time, remove the tape and let the ﬂ ap hang in the unlocked position.

drill bit.

Screw into place. Cut off excess screw with wire cutters. Cover screw holes with blanking plugs for neat ﬁ nish. Push ﬁ t 4-way locking handle into place.

Using the 4-Way lock.

The ﬁ xed tunnel is an integral part of the mechanism and must not be cut or damaged. Doing so will impede the latching mechanism.

Magnetic

4-Way Locking

Cat Flap

Installation Guide for Wood Door (Metal Door Installation on Reverse)

Before installing your cat ﬂ ap, please read the following step-by-step instructions carefully

1 2 3 4

Tools Required

Drill holes at each corner.

Remove the cat ﬂ ap and drill holes with a 3/16"

drill bit.

Measure the belly height of your cat. This is usually around 4 to 6 inches.

6 7

Cut along the lines using a jigsaw.

Mark this measurement on the outside of your door and draw a straight horizontal line 6 1/2"

Using the horizontal line as the starting point, draw a square 6

Smooth out the rough edges. Place the cat ﬂ ap in the hole, with the

red 4-way lock facing inside. Mark the screw holes.

10 11 12

Screw into place. Cut off excess screw with wire cutters. Cover screw holes with blanking plugs for neat ﬁ nish. Push ﬁ t 4-way locking handle into place.

The ﬁ xed tunnel is an integral part of the mechanism and must not be cut or damaged. Doing so will impede the latching mechanism.

Place collar key on center of tunnel and push ﬂ ap. Do not force ﬂ ap open with magnet in hand. Fit hanging key to your cat’s collar.

/2" x 6 3/4".

Product Warranty

Please register you product online at www.petsafe.net. All parts are covered under warranty for the life of this product. Labor is covered for the ﬁ rst year of ownership. Thereafter, there is a minimum service charge for the repair or replacement of the product. Misuse, loss, damage by pet or improper use or handling is not covered. PetSafe consequential damage. Warranty void if product resold.

Please contact the Customer Care Center at 1-800-732-2677 (US), 1-800457-3911 (Canada) if you need service or for help in troubleshooting and, if needed, to arrange a repair for your product (a service charge may apply). Also, please visit our website www.petsafe.net for Frequently Asked Questions and Troubleshooting Tips.

Radio Systems Corporation • 10427 Electric Ave. • Knoxville, TN • 865-777-5404 • www.petsafe.net • 400-1023/1

Using the 4-Way lock.

will not pay for loss of time, inconvenience, loss of use of your product or any incidental or