Petsafe E-Z User Manual

PetSafe
®
10' x 10' E-Z Roof
Assembly Instructions
Instructions d’assemblage
Please read this entire guide before assembly.
Veuillez lire entièrement le guide avant l’assemblage.
Por favor, lea completamente esta guía antes de ensamblar.
Thank you for choosing PetSafe®. The relationship you have with your pet is the focus of everything we do. If you have questions about, or are dissatisfi ed with, any of our products, please contact the Customer Care Center at 1-888-632-4453 or visit our website at www.petsafe.net.
_________________________________________________________________________________________________________
Table of Contents
Components ................................................................................................................................... 3
Tools Needed .................................................................................................................................. 3
Connect End Rail Clamps, 20" Tubing and Elbows ........................................................................... 4
Connect Plain and Swedged Tubing ................................................................................................. 4
Add Tarp and Secure with Ball Bungees ........................................................................................... 5
Caution .......................................................................................................................................... 6
Terms of Use and Limitation of Liability .......................................................................................... 6
Français .................................................................................................................. 7
Español ..................................................................................................................12
2 1-888-632-4453
Components
Pet
S
a
f
e
®
1
0
'
x
1
0' E
-Z
R
o
o
f
As
s
e
mb
ly
Ins
t
r
u
ct
io
n
s
Ins
t
r
u
c
t
io
n
s
d
a
s
s
e
m
b
lage
I
n
s
t
r
u
c
cio
n
e
s
de m
on
t
a
je
P
le
a
s
e
r
ea
d
th
i
s
ent
i
r
e
g
u
i
d
e
b
e
f
o
re
a
s
s
e
m
b
l
y
.
V
euill
ez
lir
e e
n
ti
è
r
e
m
e
nt
l
e
g
u
i
d
e
a
v
a
n
t
a
s
s
e
m
b
l
e
é
.
Po
r favor
,
l
e
a
c
o
m
ple
t
a
me
n
t
e
e
s
t
a
gu
í
a
a
n
t
e
s
de
a
s
a
m
b
l
e
a
.
Ball Bungee Cord
14 pcs.
Plastic Elbow
2 pcs.
Ta r p
41" Tubing (Frame Rail)
Swedged on One End
2 pcs.
41.5" Tubing Plain (Frame Rail)
5
/16 x 2" Carriage Bolt
with Nut
2 pcs.
20" Tubing Plain (Upright)
2 pcs.
End Rail Clamp
4 pcs.
Assembly Instructions
Tools Needed
• Adjustable Wrench
• Pliers
www.petsafe.net 3
Step
1
Connect End Rail Clamps, 20" Tubing and Elbows
1. Gather 4 end rail clamps, 2 - 20" tubes, 2 elbows, 2 carriage bolts and 2 nuts.
2. Insert 1 elbow into 1 - 20" tube.
3. Beginning on the gate panel side, attach 2 end rail clamps to top frame of the kennel panel. Position end rail clamps in the center of the gate panel.
4. Install 20" tube with elbow into end rail clamps and tighten with 1 carriage bolt and 1 nut.
5. Repeat steps 2 through 4 on opposite side of kennel. Loosely secure the end rail clamps to the kennel frame.
__________________________________________________________________________________________________
Step
2
Connect Plain and Swedged Tubing
1. Gather 1 plain 41.5" tube and 2 swedged 41" tubes.
2. Beginning on the gate panel side, insert one swedged tube into elbow. Then insert plain tube over swedged tube. Finish by inserting remaining swedged tube into plain tube and opposite elbow.
3. Tighten end rail clamps after all tubing is assembled.
4 1-888-632-4453
Step
3
Add Tarp and Secure with Ball Bungees
1. Gather tarp and 14 ball bungees.
2. Drape long side of tarp over frame.
3. Work on one side of the kennel. Pass the cord through the grommet from the bottom up (A). Pass the cord back through the opening immediately below the ball (B). Pull the end of the cord until the ball is resting tightly against the grommet (C). The ball bungee is now “permanently” attached to the tarp.
4. Wrap cord around the kennel frame and then stretch over the ball to secure (D). Repeat steps 3 and 4 to attach all bungees to the tarp and kennel frame.
5. Once one side of the tarp is secured to the kennel, repeat steps 3 and 4 on the other side.
Important: Tarp is not designed to withstand the weight of snow. Remove cover in winter. Anchors are strongly recommended. PetSafe
B
A
®
Anchor Kit sold separately.
D
C
www.petsafe.net 5
Loading...
+ 11 hidden pages