Petsafe Deluxe In-Ground Radio Fence Operating And Training Manual
®
PetSafe
Deluxe
In-Ground Radio Fence
Operating and Training Guide
Please read this entire guide before beginning
™
RFA-67
BATTERY 6V
Thank you for choosing PetSafe®, the #1 selling brand of electronic training solutions in the world. Our
mission is to ensure your pet’s safety by providing you the tools and techniques to successfully train
your pet. If you have any questions, please contact the Customer Care Center at 1-800-732-2677 or
visit our website at www.petsafe.net.
___________________________________________
Table of Contents
Components ................................................................................................................................... 3
Other Items You May Need .............................................................................................................. 3
How the System Works .................................................................................................................... 4
Key Defi nitions ............................................................................................................................... 4
Operating Guide
Locate the Fence Transmitter ....................................................................................................... 5
Lay Out the System ..................................................................................................................... 5
Sample Layouts ........................................................................................................................... 6
Position the Boundary Wire ......................................................................................................... 7
Connect the Wires to the Fence Transmitter ................................................................................. 8
Prepare the Receiver Collar ......................................................................................................... 9
Set the Boundary Width and Test the Receiver Collar ...................................................................10
Install the Boundary Wire ...........................................................................................................11
Place the Boundary Flags ...........................................................................................................13
Fit the Receiver Collar ................................................................................................................13
Training Guide
Be Patient With Your Pet .............................................................................................................14
Day 1 - Boundary Flag Awareness ...............................................................................................15
Days 2 thru 4 - Continue Boundary Flag Awareness ....................................................................15
Days 5 thru 8 - Distraction Phase ...............................................................................................16
Days 9 thru 14 - Unleashed Supervision ......................................................................................16
Days 14 thru 30 - Pet Monitoring ...............................................................................................17
Taking Your Pet Out of the Pet Area ............................................................................................17
Accessories ....................................................................................................................................17
Troubleshooting .............................................................................................................................18
Short Loop Test .............................................................................................................................19
To Locate a Break in the Wire .........................................................................................................20
Terms of Use and Limitation of Liability .........................................................................................20
FCC ..............................................................................................................................................21
Caution .........................................................................................................................................21
Layout Grid ...................................................................................................................................23
Mounting Template ........................................................................................................................24
2 1-800-732-2677
Components
Power
Adapter
Test Light
Transmitter
Receiver
Collar w/Short
Contact Points
Contact Points
Fence
Long
Battery
(PetSafe® RFA-67)
Boundary Wire - 500 ft.
P
E
F
A
S
H
A
P
P
Y
O
In-Ground
RADIO FENCE
DELUXE
Video CD
compatible with
most DVD players
and computer
CD-ROM drives
Wire Nuts
VHS Tape
available through
our Customer
Care Center at
1-800-732-2677
Streaming Video
available at
www.petsafe.net
Installation and Training
Video CD
RFA-140
Installation
and Training
Video CD
Warranty
Warranty
Card
E
T
S
S
R
E
N
W
™
Boundary Flags - 50
Operating and
Training Guide
Other Items You May Need
• Additional wire and fl ags (Part #PRFA-500)
• Tape measure
• Drill & mounting hardware
• Shovel or lawn edger
• Pliers
• Wire stripping pliers
• Scissors
• Lighter
• Electrical tape
• Additional wire nuts
• Ground rod and clamp
• Waterproofi ng compound (e.g. silicone caulk)
• PVC pipe or water hose
• Circular saw with masonry blade
• Patching compound
• Staple gun
• Non-metallic collar and leash
Note: For information on professional installation of your new PetSafe In-Ground Radio FenceTM, contact the Customer Care Center
at 1-800-732-2677 or visit our website at www.petsafeprofessional.com.
www.petsafe.net 3
How the System Works
The PetSafe In-Ground Radio FenceTM has been proven safe, comfortable, and effective for all pets over 8 pounds. The
system works by producing a radio signal from the Fence Transmitter through up to 4000 feet of Boundary Wire. The
Boundary Wire is buried or attached to a fi xed object to enclose the Pet Area. You temporarily defi ne the Pet Area with
Boundary Flags for a visual aid in training your pet. Your pet wears a Receiver Collar with Contact Points that touch his
neck, and, once trained, is allowed to roam freely in the Pet Area. When your pet reaches the Warning Zone, the Receiver
Collar gives a warning beep. If your pet continues into the Static Correction Zone, a safe Static Correction will be delivered
through the Contact Points to get his attention until he returns to the Pet Area.
Key Definitions
Fence Transmitter: The device that transmits the radio signal through the Boundary Wire.
Pet Area: The area within the Warning Zone where your pet can roam freely.
Warning Zone: The outer edge of the Pet Area where your pet’s Receiver Collar begins to beep, warning him not to go into
the Static Correction Zone.
Static Correction Zone: The zone beyond the Warning Zone where your pet’s Receiver Collar will emit a Static
Correction, signaling him to return to the Pet Area.
Boundary Width: The combination of the Warning Zone and the Static Correction Zone.
Receiver Collar: The device that receives the radio signal from the Boundary Wire.
Correction Level Button: The button to adjust the level of Static Correction your pet receives in the Static Correction Zone.
Receiver LED Indicator Light: The light that indicates the level of correction at which the Receiver Collar is set. This
light also serves as a low battery indicator.
Contact Points: The contacts through which the Receiver Collar delivers the safe Static Correction when your pet moves
into the Static Correction Zone.
Power Jack: The jack where the Power Adapter plugs into the Fence Transmitter. The Fence Transmitter is powered by a
standard 120-volt outlet.
Boundary Control Switch: The switch to adjust according to the length of Boundary Wire used.
Ground Terminal: The terminal where the Ground Wire connects to the Fence Transmitter.
Boundary Wire Ter minals: The terminals where the Boundary Wires connect to the Fence Transmitter in order to
complete a continuous loop.
Loop Indicator Light: The light that indicates that the Boundary Wire makes a complete loop, enabling the signal to be
transmitted.
Boundary Width Control: The knob that adjusts the width of the Warning and Static Correction Zones. Note: Adjusting the
knob does not change the level of Static Correction on the Receiver Collar.
Receiver Collar
Fence Transmitter
Fence
Transmitter
Static Correction
Zone
Warning
Zone
Pet Area
Static Correction
Zone
Warning
Zone
Boundary
Width
4 1-800-732-2677
Correction Level Button
Battery
Washers
Contact Points
Receiver
LED
Indicator Light
Power
Jack
Boundary
Control
Switch
Ground
Ter minal
Boundary Wire
}
Ter minals
Loop Indicator Light
Power Light
Boundary Width
Control
Operating Guide
Step
1
Locate the Fence Transmitter
Place the Fence Transmitter:
• In a dry, well ventilated, protected area (1A, 1B).
• In an area where temperatures do not fall below freezing (e.g., garage, basement, shed, closet).
• Secured to a stationary surface using appropriate mounting hardware (not included). A mounting template is
included in the back of this guide.
• At least 3 feet from large metal objects or appliances as these items may interfere with the signal consistency (1C).
Once you have mounted the Fence Transmitter, the Boundary Wire must exit the building. This can be
accomplished via a window or through a 1/8” hole drilled through the wall. Ensure the drill path is clear of any
utilities. Make sure the Boundary Wire is not cut off or pinched by a window, door, or garage door, as this can
damage it over time.
To prevent fi res and electrical hazards, install the Fence Transmitter in buildings that are in accordance with state
and local electrical codes.
1A
1B
__________________________________________________
1C
3ft.
Step
2
Lay Out the System
Basic Planning Tips
• The Boundary Wire MUST start at
the Fence Transmitter and make a
continuous loop back (2A).
• Design a layout that is suitable for your
yard. Sample layouts are provided in
this section, and a grid for designing
your layout is provided in the back of
this guide.
• Always use gradual turns at the
corners to produce a more consistent
boundary (2B). Do not use sharp
turns, as this will cause gaps in your
boundary.
• Avoid making passageways too narrow
for your pet to move about freely (e.g.,
along the sides of a house).
• The Receiver Collar can be activated
inside the house if the Boundary Wire runs along the outside wall of the house. If this occurs, remove your
pet’s Receiver Collar before bringing him inside, decrease the range using the Boundary Width Control or
consider an alternative layout.
2A 2B
www.petsafe.net 5
Sample Layouts
3-5'
3-5'
Sample 1:
Perimeter Loop
(Single Loop) The
Perimeter Loop is
the most common
layout. This will
allow your pet to
freely and safely
roam your entire
property (2C). It
can also protect
gardens, pools and
landscaping (2D).
C
B
D
A
E
Sample 2 (2E): Perimeter Loop Using Existing
Fence (Single Loop)
This layout allows you to include your existing fence
as part of your layout and keep your pet from jumping
out or digging under your existing fence. It reduces the
amount of wire which will need to be buried. From the
Fence Transmitter, run the wire to A, A to B, B to C, C
to D, D to E, E to A, twist the wires from A back to the
Fence Transmitter. See the “Install the Boundary Wire”
section for more information on attaching the wire to a
fence.
Double Loop
A Double Loop must be used when you are not establishing the Boundary Zone on all sides of your property.
When using a Double Loop, the Boundary Wire must be separated by a minimum of THREE TO FIVE FEET to
avoid canceling the signal. Remember that a Double Loop will require twice as much wire.
D
C
A
B
A
B
C
Sample 3 (2F): Front or Back
Yard Only (Double Loop)
From the Fence Transmitter, run
the wire to A, A to B, B to C, C
to D, D to E, E to F, make a Uturn and follow your path all the
way back to A, keeping the wire
separated three to fi ve feet. Twist
the wire from A back to the Fence
Transmitter.
E
F
E
E
F
B
D
A
Sample 4 (2G): Front
Boundary Only
(Double Loop)
From the Fence Transmitter,
run the wire to A, A to B, B
back to A keeping the wire
separated three to fi ve feet.
Twist the wire from A back to
the Fence Transmitter.
B
A
C
D
Sample 5 (2H): Lake Access
(Double Loop)
From the Fence Transmitter,
run the wire to A, A to B,
make a U-turn and go to C, C
to D, D to E, make a U-turn
and follow your path all the
way back to A keeping wire
separated three to fi ve feet.
Twist the wire from A back to
the Fence Transmitter.
6 1-800-732-2677
Sample 6 (2J): Wire Loop Attached to Existing Fence (Double Loop)
3-5'
10
Twists/ft.
This layout allows you to include your existing fence as part of your layout and
keep your pet from jumping out or digging under your existing fence. It reduces
the amount of wire which will need to be buried. Run the wire from the Fence
Transmitter to A, A to B, B to C, C to D, D to E, E to F, make a U-turn and
follow your path all the way back to A,
feet. Twist the wire from A back to the Fence Transmitter. See the “Install the
Boundary Wire” section for more information on attaching the wire to a fence.
keeping the wire separated three to fi ve
C
A
B
D
F
__________________________________________________
E
Step
3
Position the Boundary Wire
Lay out the Boundary Wire using your proposed boundary and test the system BEFORE burying the wire or
attaching it to an existing fence. This will make any layout changes easier.
Running the Boundary Wire parallel to and within fi ve feet of electrical wires, neighboring containment systems,
telephone wires, television or antenna cables, or satellite dishes will cause an inconsistent signal. If you must cross
any of these, do so at 90-degree angles (perpendicularly).
If separating your Boundary Wire by at least fi ve feet from a neighboring containment system’s wire does not reduce
the inconsistent signal, contact the Customer Care Center at 1-800-732-2677.
To Twist the Boundary Wire (3A)
Twisting the Boundary Wire cancels the signal and allows your pet to cross over that area safely. Plastic or metal
piping will not cancel the signal. Twist the Boundary Wire 8 to 10 times per foot to cancel the signal.
To Splice or Repair the Boundary Wire (3B)
If you need additional Boundary Wire to expand your wire loop, you will need to splice the wires together. Note the
locations of all splices for future reference. Most Boundary Wire breaks occur at splices.
Strip approximately one-half inch of insulation off the ends of the Boundary Wires to be spliced. Make sure the
copper Boundary Wire is not corroded. If the Boundary Wire is corroded, cut it back to expose clean copper wire.
Insert the stripped ends into the wire nut and twist the wire nut around the wires. Pull on the wires to make sure
you have a strong splice connection. Apply waterproofi ng compound (e.g. silicone caulk) in and around the wire nut
or wrap the wires and the wire nuts with electrical tape to prevent moisture from corroding the copper.
If your splice pulls loose, the entire system will fail. Make sure your splice is secure.
1/2"
1/2"
1
2
www.petsafe.net 7
Additional Boundary Wire
We recommend the use of 20 gauge insulated multi-strand copper
wire for direct burial. Extra Boundary Wire can be purchased in 500
foot spools at the store where you purchased the kit or through the
Customer Care Center at 1-800-732-2677.
Note: When adding Boundary Wire, it must act as a continuous loop.
The table at right indicates the approximate length of Boundary Wire
needed for a rectangular, Single Loop layout. Length will vary due to
the amount of twisted wire and layout used.
Acres Feet of Wire Needed
1/4 415
1/3 480
1/2 590
1 835
2 1180
5 1870
25 4000
__________________________________________________
Step
4
Connect the Wires to the Fence Transmitter
Boundary Wire (4A)
1. Run the Boundary Wire to the Fence Transmitter through a window, under
a door, through a crawl space vent, or any other appropriate available access.
You can also drill a hole through your wall.
2. Strip the ends of the Boundary Wire approximately one-half inch.
3. Insert the Boundary Wires into the Boundary Wire Terminals on the Fence
Transmitter.
4. Turn the Boundary Width Control knob to 10. This will set the Warning Zone
at the maximum width.
5. Plug the Power Adapter into the Power Jack and a 120-volt outlet.
6. The Power Light and Loop Indicator Lights should come on. If this does not
happen, see the “Troubleshooting” section.
Ground Wire (4B)
Proper grounding, although not necessary for the system to work, will
help reduce the chance of electrical surges causing damage to your Fence
Transmitter and/or Power Adapter. To ground your unit, you will need a solid
(not stranded) Ground Wire (14 to 18 gauge insulated copper wire) and a
ground rod with clamp, which may be obtained at most electrical supply stores.
Connect one end of the Ground Wire to the Ground Terminal located on the
Fence Transmitter and the other end of the Ground Wire to the ground rod.
The ground rod must be buried at least three feet into the ground and located
as close as possible to the Fence Transmitter.
4B
4A
Power
Jack
Ground
Terminal
Boundary Wire
}
Terminals
Loop Indicator
Light
Power Light
Boundary Width
Control
Ground
Wire
Fuse Protection (4C)
The Fence Transmitter is also equipped with a 250 volt, ½ amp fuse to protect the
unit’s electronic circuitry from electrical power surges. To locate the fuse, slide off
the lid on the back of the Fence Transmitter. A spare fuse is also provided.
Lightning Protection
You may purchase a Lightning Protection Kit through the Customer Care Center
at 1-800-732-2677. The Lightning Protection Kit protects the system against
surges that travel through the power source and/or the Boundary Wire. If you use
a Lightning Protection Kit, the Ground Wire must be removed from the Fence
Transmitter. The Lightning Protection Kit utilizes a ground connection separate
from the Fence Transmitter.
8 1-800-732-2677
4C
Spare Fuse
Fuse
Loading...