Please read this entire guide before installation.
Thank you for choosing PetSafe®, the best selling brand of electronic training solutions in the world. Our mission is to be the most
trusted brand in the pet ownership experience. We want to ensure your pet’s safety by providing you with the tools and techniques
to successfully train your pet. If you have any questions, please contact the Customer Care Center at 1-800-732-2677 or visit our
website at www.petsafe.net.
To get the most protection out of your limited warranty, please register your product within 90 days at www.petsafe.net. By
registering, you will enjoy the product’s full warranty and should you ever need to call the Customer Care Center, we will be able
to help you faster. Additionally, you will not have to save your product receipt as registering serves as proof of purchase. Most
importantly, PetSafe will never give or sell your valuable information to anyone.
**Required for supervised tie-out training. On-lead training does not require tie-out.
Note: For information on professional installation of your new PetSafe® Deluxe In-Ground Cat Fence™, contact the Customer Care Center at
1-800-732-2677 or visit our website at www.petsafepro.com.
www.petsafe.net 3
How the System Works
The PetSafe® Deluxe In-Ground Cat Fence™ has been proven safe, comfortable, and effective for all cats over 6 lb. and at least
6 months old. The system works by producing a radio signal from the Fence Transmitter through up to 4000 ft. of Boundary
Wire. The Boundary Wire is buried or attached to a fi xed object to enclose the Pet Area. You temporarily defi ne this Pet Area
with Boundary Flags for a visual aid in training your cat. Your cat wears a Receiver Collar with Contact Points that touch his
neck and, once trained, is allowed to roam freely in the Pet Area. When your cat reaches the Warning Zone, the Receiver Collar
gives a warning beep. If your cat continues into the Static Correction Zone, a safe Static Correction will be delivered through
the Contact Points to get his attention until he returns to the Pet Area.
Key Definitions
Fence Transmitter: The device that transmits the radio signal through the Boundary Wire.
Pet Area: The area within the Warning Zone where your cat can roam freely.
Warning Zone: The outer edge of the Pet Area where your cat’s Receiver Collar begins to beep, warning him not to go into
the Static Correction Zone.
Static Correction Zone: The zone beyond the Warning Zone where your cat’s Receiver Collar will emit a Static
Correction, signaling him to return to the Pet Area.
Boundary Width: The combination of the Warning Zone and the Static Correction Zone.
Receiver Collar: The device that receives the radio signal from the Boundary Wire.
Correction Level Button: The button to adjust the level of Static Correction your cat receives in the Static Correction
Zone.
Receiver Indicator Light: The light that indicates the level of correction at which the Receiver Collar is set. This light also
serves as a low battery indicator.
Contact Points: The contacts through which the Receiver Collar delivers the safe Static Correction when your cat moves
into the Static Correction Zone.
Power Jack: The jack where the Power Adapter plugs into the Fence Transmitter. The Fence Transmitter is powered by a
standard 120-volt outlet.
Boundary Control Switch: The switch to adjust according to the length of Boundary Wire used.
Boundary Wire Ter minals: The terminals where the Boundary Wires connect to the Fence Transmitter in order to
complete a continuous loop.
Loop Indicator Light: The light that indicates that the Boundary Wire makes a complete loop, enabling the signal to be
transmitted.
Boundary Width Control: The knob that adjusts the width of the Warning and Static Correction Zones. Note: Adjusting the
knob does not change the level of Static Correction on the Receiver Collar.
Fence
Transmitter
Pet Area
Static Correction
Zone
Warning
Zone
Receiver Collar
(Top)
Correction
Level Button
Fence Transmitter
Receiver
Indicator
Light
Contact
Poin ts
Static Correction
Zone
Warning
Zone
Boundary
Width
Battery Module
4 1-800-732-2677
(Bottom)
Power
Jack
Boundary
Control
Switch
Ground
Ter minal
Boundary Wire
}
Ter minals
Loop Indicator Light
Power Light
Boundary Width
Control
10
Twists/ft.
Operating Guide
Step
1
Locate the Fence Transmitter
Place the Fence Transmitter:
• In a dry, well ventilated, protected area (1A, 1B).
• In an area where temperatures do not fall below freezing (e.g., garage, basement, shed).
• Secured to a stationary surface using appropriate mounting hardware (not included). A mounting template is
included on the back of this guide.
•
At least 3 feet from large metal objects or appliances, as these items may interfere with the signal consistency (1C).
Once you have mounted the Fence Transmitter, the Boundary Wire must exit the building. This can be
accomplished via a window or through a 1/8 in. hole drilled through the wall. Ensure the drill path is clear of any
utilities. Make sure the Boundary Wire is not cut off or pinched by a window, door, or garage door, as this can
damage it over time.
To prevent fi res and electrical hazards, install the Fence Transmitter in buildings that are in accordance with state
and local electrical codes.
• When planning your layout, take care to
exclude access to trees, sheds or other items
your cat can use to jump over the Boundary.
The signal from the Boundary Wire only
extends the same distance vertically as
horizontally. If your cat can take the Receiver
Collar out of reach of the signal, he can jump
the Boundary without receiving a Static
Correction.
•
The Boundary Wire MUST start at the Fence
Transmitter and make a continuous loop back
(2A).
• Design a layout that is suitable for your yard.
Sample layouts are provided in this section,
and a grid for designing your layout is provided in the back of this guide.
• Fence Planning Software is available online at www.petsafe.net/fence. After you have planned and saved your
layout online, contact our Customer Care Center to review and refi ne your layout.
• Twisting two sides of the Boundary Wire cancels the signal and allows your cat to cross over that area safely.
Plastic or metal piping will not cancel the signal. Twist the Boundary Wire 10 to 12 times per foot to cancel the
signal
(2A)
.
• Always use gradual turns at the corners to produce a more consistent boundary (2B). Do not use sharp turns, as
this will cause gaps in your boundary.
• Avoid making passageways too narrow for your cat to move about freely (e.g., along the sides of a house).
• The Receiver Collar can be activated inside the house if the Boundary Wire runs along the outside wall of the
house. If this occurs, remove your cat’s Receiver Collar before bringing him inside, decrease the range using the
Boundary Width Control Knob, or consider an alternative layout.
2A
2B
www.petsafe.net 5
Sample Layouts
3-5'
3-5
'
Sample 1:
Perimeter Loop
(Single Loop)
The Perimeter
Loop is the
most common
layout. This will
allow your cat to
freely and safely
roam your entire
property (2C). It
can also protect
gardens, pools and
landscaping (2D).
Sample 2 (2E): Perimeter Loop Using Existing
Fence (Single Loop)
This layout allows you to include your existing fence as
part of your layout and keep your cat from jumping out or
digging under your existing fence. It reduces the amount
of wire which will need to be buried. From the Fence
Transmitter, run the wire to A, A to B, B to C, C to D,
D to E, E to A, twist the wires from A back to the Fence
Transmitter. See the “Install the Boundary Wire” section
for more information on attaching the wire to a fence.
Double Loop
A Double Loop must be used when you are not establishing the Boundary Zone on all sides of your property.
When using a Double Loop, the Boundary Wire must be separated by a minimum of 3 TO 5 FEET to avoid
canceling the signal. Remember that a Double Loop will require twice as much wire.
D
C
A
B
A
B
C
E
F
E
F
D
Sample 3 (2F): Front or Back
Yard Only (Double Loop)
From the Fence Transmitter, run
the wire to A, A to B, B to C, C
to D, D to E, E to F, make a Uturn and follow your path all the
way back to A, keeping the wire
separated 3 to 5 feet. Twist the
wire from A back to the Fence
Transmitter.
B
A
Sample 4 (2G): Front
Boundary Only
(Double Loop)
From the Fence Transmitter,
run the wire to A, A to B, B
back to A keeping the wire
separated 3 to 5 feet. Twist the
wire from A back to the Fence
Transmitter.
E
B
A
C
D
Sample 5 (2H): Lake Access
(Double Loop)
From the Fence Transmitter,
run the wire to A, A to B,
make a U-turn and go to C, C
to D, D to E, make a U-turn
and follow your path all the
way back to A keeping wire
separated 3 to 5 feet. Twist
the wire from A back to the
Fence Transmitter.
This layout allows you to include your existing fence as part of your layout and
keep your cat from jumping out or digging under your existing fence. It reduces
the amount of wire which will need to be buried. Run the wire from the Fence
Transmitter to A, A to B, B to C, C to D, D to E, E to F, make a U-turn and
follow your path all the way back to A,
the wire from A back to the Fence Transmitter. See the “Install the Boundary Wire”
section for more information on attaching the wire to a fence.
Lay out the Boundary Wire using your planned boundary and test the system BEFORE burying the wire
or attaching it to an existing fence. This will make any layout changes easier.
Running the Boundary Wire parallel to and within 5 feet of electrical wires, neighboring containment systems,
telephone wires, television or antenna cables, or satellite dishes may cause an inconsistent signal. If you must cross
any of these, do so at 90-degree angles (perpendicularly).
If separating your Boundary Wire by at least 5 feet from a neighboring containment system’s wire does not reduce
the inconsistent signal, contact the Customer Care Center at 1-800-732-2677.
To Twist the Boundary Wire (3A)
Twisting the Boundary Wire cancels the signal and allows your cat to cross over that area safely. Plastic or metal
piping will not cancel the signal. Twist the Boundary Wire 10-12 times per foot to cancel the signal. The maximum
length of twisted wire is 50 feet.
To Splice or Repair the Boundary Wire (3B)
If you need additional Boundary Wire to expand your wire loop, you will need to splice the wires together. Note the
locations of all splices for future reference. Most Boundary Wire breaks occur at splices.
Strip approximately ½ in. of insulation off the ends of the Boundary Wires to be spliced. Make sure the copper
Boundary Wire is not corroded. If the Boundary Wire is corroded, cut it back to expose clean copper wire.
Insert the stripped ends into the wire nut and twist the wire nut around the wires. Pull on the wires to make sure
you have a strong splice connection. Apply waterproofi ng compound (e.g. silicone caulk) in and around the wire nut
or wrap the wires and the wire nuts with electrical tape to prevent moisture from corroding the copper.
If your splice pulls loose, the entire system will fail. Make sure your splice is secure.
1/2"
1/2"
www.petsafe.net 7
1
2
Additional Boundary Wire
We recommend the use of 20 gauge insulated multi-strand copper wire for direct burial.
Extra Boundary Wire can be purchased in 500 ft. spools at the store where you purchased
the kit or through the Customer Care Center at 1-800-732-2677.
Note: When adding Boundary Wire, it must act as a continuous loop.
The table at right indicates the approximate length of Boundary Wire needed for a
rectangular, Single Loop layout. Length will vary due to the amount of twisted wire and
layout used. Remember that a double loop will require twice as much wire.
1. Run the Boundary Wire to the Fence Transmitter through a window, under
a door, through a crawl space vent, or any other appropriate available access.
You can also drill a hole through your wall.
2. Strip the ends of the Boundary Wire approximately ½ in.
3. Insert the Boundary Wires into the Boundary Wire Terminals on the Fence
Transmitter.
4. Turn the Boundary Width Control knob to 10. This will set the Warning Zone
at the maximum width.
5. Plug the Power Adapter into the Power Jack and a 120-volt outlet.
6. The Power Light and Loop Indicator Lights should come on. If this does not
happen, see the “Troubleshooting” section.
Ground Wire (4B)
Proper grounding, although not necessary for the system to work, will help reduce the
chance of electrical surges causing damage to your Fence Transmitter and/or Power
Adapter. To ground your unit, you will need a solid (not stranded) Ground Wire
(14 to 18 gauge insulated copper wire) and a ground rod with clamp, which may be
obtained at most electrical supply stores. Connect one end of the Ground Wire to the
Ground Terminal located on the Fence Transmitter and the other end of the Ground
Wire to the ground rod. The ground rod must be buried at least three feet into the
ground and located as close as possible to the Fence Transmitter.
4A
Power
Jack
4B
Loop Indicator
Light
Power Light
Boundary Width
Control
Ground
Terminal
Boundary Wire
}
Terminals
Ground
Wire
Fuse Protection (4C)
The Fence Transmitter is also equipped with a 250 volt, ½ amp fuse to protect the
unit’s electronic circuitry from electrical power surges. To locate the fuse, slide off the
lid on the back of the Fence Transmitter. A spare fuse is also provided.
Lightning Protection
You may purchase a Lightning Protection Kit through the Customer Care Center at
1-800-732-2677. The Lightning Protection Kit protects the system against surges that
travel through the power source and/or the Boundary Wire. If you use a Lightning
Protection Kit, the Ground Wire must be removed from the Fence Transmitter.
The Lightning Protection Kit utilizes a ground connection separate from the Fence
Transmitter.
8 1-800-732-2677
4C
Spare Fuse
Fuse
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.