INSTALLATION AND OPERATION INSTRUCTIONS
STANDARD BACK BAR COOLERS, SELF CONTAINED
MODEL NOS.
CS Series
IMPORTANT INFORMATION
Fill out the enclosed warranty card and mail to the
Perlick Corporation to register the warranty. If the
card is not returned, the warranty period will begin
from the date the equipment is shipped from the
factory.
This manual has been prepared to assist you in the
installation of your Cabinet and to acquaint you with
its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If service is required, your dealer can
provide you with a list of qualified service agents. For
your own protection, never return merchandise for
credit without our approval.
We thank you for selecting a Perlick product and
assure you of our continuing interest in your
satisfaction.
WARNING: When lifting, the full weight of the
cabinet must be supported. Lift from the cabinet
base and not from the top. Improper lifting can
result in severe damage to the cabinet.
Table of Contents
PREPARING THE CABINET FOR USE
Specifications.........................................................2
List of Included Parts.............................................3
Tools Required.......................................................3
Plumbing................................................................3
Electrical................................................................3
Installing Casters or Legs .....................................3
TEMPERATURE
Refrigeration and Temperature Control.................4
CLEANING
Cleaning the Cabinet.............................................4
Replacement Parts................................................5
Cleaning Stainless Steel........................................6
Wiring Diagram......................................................7
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com
Form No. Z2087A
Rev. 08.03.04
Installation and Operating Instructions
Sizes and Specifications, Standard Back Bar Coolers – Self-Contained
MODEL NUMBERS
BLACK FINISH CS2DPSP CS3DPSP CS4DPSP
BLACK W/GLASS DOORS CS2DPSG CS3DPSG CS4DPSG
STAINLESS STEELFINISH CS2DSSS CS3DSSS CS4DSSS
STAINLESS W/GLASS DOORS CS2DSST CS3DSST CS4DSST
SPECIFICATIONS
NUMBER OF DOORS 2 3 4
CABINET LENGTH Ins. (mm) 60” (1524) 84” (2134) 108” (2743)
NUMBER OF SHELVES 4 6 8
CONDENSING UNIT H.P.
1
/4
RUNNING LOAD - AMPS 5.9 7.5 7.5
SHIP WT lbs. (kg) 380 (172) 490 (222) 630 (286)
INTERIOR Fourteen gauge stainless steel sills are reinforced with a 12 gauge angle bracket that extends from one
end of the insulated base to the other. The floor pan is 20 gauge, type 304 stainless steel. The walls and
ceiling are 20 gauge galvanized steel.
EXTERIOR All Models: The top is 20 gauge stainless steel. The back is 20 gauge galvanized steel.
Bottom is 20 gauge stainless steel.
Black Models: Doors, front and sides are 20 gauge black powder coated steel.
Stainless Models: Doors, front and sides are 20 gauge stainless steel.
REFRIGERATION R-134a capillary tube-type. Aluminum fin and copper tube evaporator coil. Adjustable temperature control.
Self-defrosting. Pull-out condensing unit for easy service and cleaning. Compressor left.
VENTILATION Front ventilated.
ELECTRICAL 115 Volt, 60 Hz., 1 Phase AC. Furnished with three-prong, six foot rubber cord. Contact Perlick for other
voltage/frequency requirements.
PLUMBING Floor drain
3
4” female taper pipe exits out right bottom or right end (for optional use). None required.
/
Condensate evaporates automatically.
INSULATION Foamed-in-place polyurethane; 2” walls, 1
1
OPTIONALACCESSORIES • Leg Set • Caster Sets • Base Plate Set
• End Plate • Glass Doors w/Black Frame
* NOTE: This equipment is intended for the storage and display of non-potentially hazerdous bottle and canned products only.
1
/3
2” top and floor.
/
1
/3
Form No. Z2087A
Rev. 08.03.04
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
2
Preparing the Cabinet for Use – Standard Back Bar Coolers
Parts List
■ (2) Shelves Per Door.
■ Mini-Fluorescent Lights.
■ Shelf Clips.
Tools Required
■ #2 Phillips Screwdriver.
■ 10” Crescent Wrench.
3
■
/8” Nut driver.
9
■
/16” Allen Wrench.
■ Power Drill or Driver
(for leg installation)
.
Plumbing
Self-Contained models — None required, condensate evaporates automatically.
Electrical
The cabinet must be connected to a separately
fused power source (see electrical specification
plate) and grounded in accordance with National
and Local Electrical Codes. Caution: Do not
attempt to operate the equipment on any other
power source than that listed on the Electrical
Specification plate.
Leveling the Cabinet
When the cabinet is in place, check installation with
a carpenter’s level. When perfectly level,
accumulated water will drain out. Aslight pitch to
the drain side will not harm the cabinet. Water
may accumulate if cabinet is pitched to the
opposite side.
Installing Casters or Legs (Optional)
Attach casters or legs to cabinet bottom in holes
provided. Use the supplied
hex head self-tapping machine screws.
1
/4”- 20 x 3/4”
Installing Base Plate (Optional)
Attach brackets to cabinet bottom in holes provided.
Use #10 self-drilling hex sheet metal screws
(see separate instructions.) When returning cabinet
to upright position, be careful not to bend brackets.
WARNING TO AVOID COMPRESSOR DAMAGE
After returning the cabinet to an upright
position, let it stand for 24 hours before
plugging it in and running the unit.
Uncrating and Inspection
Remove all crating material before operating.
Carefully inspect cabinet for hidden damage. If
damage is discovered, file your claim immediately
with the transportation company. Perlick is
not responsible for damage in transit.
Placing the Cabinet
Push the cabinet into place using rollers when necessary. Important: Proper air flow around
the condensing unit is necessary for efficient operation. Never obstruct the air flow in and out
of the condensing unit compartment.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
3
Form No. Z2087A
Rev. 08.03.04
General Information – Standard Back Bar Coolers
Refrigeration andTemperature Control
The Back Bar Cabinet is equipped with a heavyduty refrigeration system designed to automatically
maintain a storage temperature of 36-41 degrees F.
The control is factory set at 38 degrees F.
To Adjust the Temperature:
The temperature control is inside the cabinet on
the right-hand side of the evaporator fan panel
assembly. You will need a screwdriver to turn the
adjusting screw. Make small adjustments until the
desired temperature is achieved.
Cleaning the Cabinet:
■ Disconnect all power prior to cleaning.
■ Use a mild detergent and water to clean the
inside and outside of the cabinet.
■ Inspect and clean the fan, evaporator coil and
light channel areas as necessary.
■ Dry thoroughly.
CAUTION: Never use a scouring pad or abrasive
cleaners.
Cleaning the Condenser:
Use a stiff brush to clean the dirt from the front
surface of the condenser. Keeping the condenser
free from dust and dirt will ensure efficient
operation.
CAUTION: Do not bend the fins while brushing the
front of the condenser.
■ Colder Temperatures: Turn the adjusting screw
clockwise (to the right)
■ Warmer Temperatures: Turn the adjusting
screw counterclockwise (to the left.)
The condenser fan motor turns off and on with the
condensing unit. The evaporator fan motor runs
continuously. The fan motors are lifetime lubricated
and will require no oiling.
NOTE: Cabinet temperatures lower than 34° will not
allow for proper defrosting of the evaporator coil. If
defrosting is necessary, turn the control knob to the
OFF position until coil is defrosted.
Form No. Z2087A
Rev. 08.03.04
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
4
Replacement Parts – Standard Back Bar Coolers
MODEL NOS. Serial numbers above 500,000
BLACK FINISH CS2DPSP CS3DPSP CS4DPSP
Left door 64357SLBL 64357SLBL 64357SLBL
Right door 64357SRBL 64357SRBL 64357SRBL
BLACK W/GLASS DOORS CS2DPSG CS3DPSG CS4DPSG
Left door 64360SLBL 64360SLBL 64360SLBL
Right door 64360SRBL 64360SRBL 64360SRBL
STAINLESS STEELFINISH CS2DSSS CS3DSSS CS4DSSS
Left door 64357SLSS 64357SLSS 64357SLSS
Right door 64357SRSS 64357SRSS 64357SRSS
STAINLESS W/GLASS DOORS CS2DSST CS3DSST CS4DSST
Left door 64360SLSS 64360SLSS 64360SLSS
Right door 64360SRSS 64360SRSS 64360SRSS
All Models
Magnetic door gasket 62085-1 62085-1 62085-1
Hinge set, left 63407L 63407L 63407L
Hinge set, right 63407R 63407R 63407R
Bulb clamp C6634 C6634 C6634
Wiring harness 61354-1 61354-1 61354-1
Evaporator fan motor C15239A C15239A C15239A
1
/2” diameter fan blade 57699 57699 57699
5
Fan guard assembly C25395 C25395 C25395
Pilaster strip 17
Screw, Thumb #8 x
Condenser housing grille 62562A1 62562A1 62562A1
Foam gasket grille 63044-1 63044-1 63044-1
Condensing Housing back panel 60976-1G 60976-1G 60976-1G
10x1 Phillips head pan Asheet
metal screw, zinc
Shelf kit, end 57928 57928 57928
Plug-in fluorescent light 57822 57822 57822
Condensing units
1
/4 h.p. condensing unit
115 volt, 60 hz.
Condensing unit (
Compressor (
Fan Motor Assembly 215315009 N/A N/A
Condenser coil 15352019 N/A N/A
Terminal board 219101538 N/A N/A
Overload protector MRT20AGK5590 N/A N/A
Relay 21351619 N/A N/A
Capacitor (
Coil assembly 2 door SC BB 62210A1* N/A N/A
Fin coil, evaporator C17511-1 N/A N/A
Condensing units
1
/3 h.p. condensing unit 115 volt N/A C22646 C22646
Condensing unit (
Compressor (
Fan Motor Assembly N/A 215315009 215315009
Condenser coil N/A 15352019 15352019
Terminal board N/A 219101538 219101538
Overload protector N/A MRT22AFZ5590 MRT22AFZ5590
Relay N/A 21351619 21351619
Capacitor (
Coil assembly
Fin coil, evaporator N/A C17511-2 C17511-2
Shelf kit, center N/A 57929 57929
*Contact Perlick Service department (800) 777-7267 for local distributors
7
/8” long C19271-1 C19271-1 C19271-1
1
/2” long M50035-122 M50035-122 M50035-122
M50048-127 M50048-127 M50048-127
(2 door models)
C22647 N/A N/A
model UFI10HBX
model FFI10HBX
282-339 MFD. 155V
(3 & 4 door models)
model UFI12HBX
model FFI12HBX
378-454 MFD. 115V
3
⁄4 door SC BB N/A 62210A2* 62210A2*
) 515301063 N/A N/A
) 513200314 N/A N/A
) 13556529 N/A N/A
) N/A 515301062 515301062
) N/A 513200003 513200003
) N/A 13556532 13556532
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
5
Form No. Z2087A
Rev. 08.03.04
Cleanning Stainless Steel – Standard Back Bar Coolers
Recommended Cleaning Agents
JOB CLEANING AGENT* COMMENTS
Routine Cleaning Soap, ammonia, detergent Apply with sponge or cloth.
Can be used on all finishes.
Fingerprints and smears Areal 20, Lac-O-Nu, Lumin Wash, Provides barrier film to minimize
O’Cedar Cream Polish fingerprints. Can be used on all finishes.
Stubborn stains and Allchem Concentrated Cleaner, Rub lightly, using dry or damp
Discolorations Samae, Twinkle, Zud Restoro, cloth in the direction of polish
Grade F or FFF Italian Pumice, lines on the stainless steel.
Whiting or Talc, Liquid Nu Steel,
Copper’s or Revere Stainless Steel
Cleaner, Lumin Cleaner, Sta-Clean,
Cameo Copper Cleaner, Allen Polish
Highlite, Penny-Brite, Copper Brite
*
Use of propriety names is intended only to indicate a type of cleaner and does not constitute an endorsement.
Omission of any proprietary cleaner does not imply its inadequacy. All products should be used in strict accordance
with instructions on the package.
NOTE: Do Not Use Steel Wool or Scouring Pads to clean stainless steel.
Form No. Z2087A
Rev. 08.03.04
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
6
Wiring Diagram – Standard Back Bar Coolers
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
7
Form No. Z2087A
Rev. 08.03.04
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2087A
Rev. 08.03.04
Loading...