Page 1
INSTALLATION AND OPERATION INSTRUCTIONS
CUSTOM BACK BAR CABINET — SELF CONTAINED AND REMOTE
MODEL NOS.
BS Series
BR Series
BS Series
IMPORTANT INFORMATION
Fill out the enclosed warranty card and mail to the
Perlick Corporation to register the warranty. If the
card is not returned, the warranty period will begin
from the date the equipment is shipped from the
factory.
This manual has been prepared to assist you in the
installation of your Cabinet and to acquaint you with
its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If service is required, your dealer can
provide you with a list of qualified service agents. For
your own protection, never return merchandise for
credit without our approval.
We thank you for selecting a Perlick product and
assure you of our continuing interest in your
satisfaction.
BR Series
Table of Contents
PREPARING THE CABINET
Specifications......................................................2,3
List of Included Parts.............................................4
Tools Required.......................................................4
Plumbing................................................................4
Electrical................................................................4
Uncrating and Inspection .......................................4
Placing the Cabinet ...............................................4
Leveling the Cabinet ..............................................4
Installing Casters or Legs .....................................4
Installing the Base Plate........................................4
Refrigeration and Temperature Control.................5
Cleaning the Cabinet.............................................5
Cleaning Stainless Steel........................................5
Replacement Parts................................................6
Reversing Door Hinge...........................................7
Wiring Diagram......................................................8
WARNING: When lifting, the full weight of the
cabinet must be supported. Lift from the cabinet
base and not from the top. Improper lifting can
result in severe damage to the cabinet.
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com
Form No. Z2278
Page 2
Installation and Operating Instructions
Sizes and Specifications, Custom Back Bar Cabinets – Self Contained
MODEL NOS. BS60 BS84 BS108
NUMBER OF DOORS 2 Door 3 Door 4 Door
CABINET Length 60” (1524) 84” (2134) 108” (2743)
DIMENSIONS Depth 24
(mm) Height 34
CASE CAPACITY
(based on 12oz. Export bottle) 12.9 20.4 27.7
CONDENSING UNIT H.P.
RUNNING LOAD –AMPS 6.3 8.1 8.3
Ship Wt. Lbs. (kg.) 380 (172) 490 (222) 630 (286)
INTERIOR Door sill: High strength polyethylene. Door pan and ceiling: High strength polystyrene. Floor pan and
Walls: Stainless steel. Includes pilasters, (2) vinyl coated shelves and floor rack per door, and interior lights.
EXTERIOR: Front, back, top and sides stainless steel. Bottom galvanized steel.
DOOR HINGING Stainless steel hinges with standard locations as illustrated. For special hinging specify
hinge locations starting from left to right. Field reversible.
DOOR HARDWARE Door handles: Black vinyl with chrome ends. Lock finish: chrome
REFRIGERATION R-134A capillary tube-type. Aluminum fin and copper tube evaporator, epoxy coated coil. Adjustable
temperature control. Self-defrosting. Pull-out condensing unit for service and cleaning.
Compressor left, standard.
ELECTRICAL 1 1 5V, 60Hz., 1 phase AC. Furnished with 3-prong, 6 foot NEMA5-15 PC cord. Contact Perlick for other voltage/
frequency requirements.
PLUMBING None required. Condensate evaporates automatically.
INSULATION Foamed-in-place polyurethane, 2” walls, 1
OPTIONAL • Leg set • Compressor right Door finishes
ACCESSORIES & • Tapping kit • Brass hardware Black vinyl coated
MODIFICATIONS • Laminated top • Caster sets Stainless steel
• Laminated ends • Base plates Customers choice of laminate
• Laminated grille • Floor access kit Prepared for field lamination
3
/4” (629) 243/4” (629) 243/4” (629)
1
/2” (876) 341/2” (876) 341/2” (876)
1
/4
1
2” top.
/
1
/3
1
/3
Glass door with black vinyl coated frame
Glass door with stainless steel frame
Glass door with laminated frame
6 3/16”
[157]
OPTIONAL
FLOOR
ACCESS
KIT 2”
Form No. Z2278
12”
[305]
5 1/8”
[130]
108” [2743] 4 DOOR
84” [2134] 3 DOOR
60” [1524] 2 DOOR
92” [2337] 4 DOOR
68” [1727] 3 DOOR
44” [1118] 2 DOOR
6 5/16”
[161]
23 1/2”
[597]
DOOR
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
19 7/8”
[505]
DOOR
OPENING
R23 1/2”
“NOTE B”
4 1/4”
[107]
18 3/4” [476]
BACK LINER
TO INSIDE OF
DOOR SILL
NOTE A: 3/4” NPT DRAIN EXIT
NOTE B: 1” DRAIN ACCESS
31 1/4”
[794]
DOOR
HEIGHT
OPENING
6 3/8”
[163]
27 7/16”
[697]
DOOR
24 3/4”
[629]
7 3/4”
[197]
4 3/16”
[106]
22 3/4”
[578]
7 3/16”
1 1/8”
[29]
2
[182]
34 1/2”
[876]
“NOTE A”
Page 3
Installation and Operating Instructions
Sizes and Specifications, Custom Back Bar Cabinets – Remote
MODEL NOS. BR48 BR72 BR96
NUMBER OF DOORS 2 Door 3 Door 4 Door
CABINET Length 48” (1219) 72” (1829) 96” (2439)
DIMENSIONS Depth 24
(mm) Height 34
CASE CAPACITY
(based on 12oz. Export bottle) 12.9 20.4 27.7
AMPS .9 .9 .9
BTU/HR 1800 2200 2600
Ship Wt. Lbs. (kg.) 380 (172) 490 (222) 630 (286)
INTERIOR Door sill: High strength polyethylene. Door pan and ceiling: High strength polystyrene.
Floor pan: Stainless steel. Includes pilasters, (2) vinyl coated shelves and floor rack per door, and interior lights.
EXTERIOR: Front, back, top and sides, stainless steel. Bottom galvanized steel.
DOOR HINGING Stainless steel hinges with standard locations as illustrated. For special hinging specify
hinge locations starting from left to right. Field reversible.
DOOR HARDWARE Door handles: Black vinyl with chrome ends. Lock finish: chrome
REFRIGERATION Aluminum fin and copper tube evaporator, epoxy coated coil.
ELECTRICAL 115 V, 60Hz., 1 phase AC. Contact Perlick for other voltage/ frequency requirements.
PLUMBING Independent floor drain or condensate evap. pan is req’d. Optional 2
INSULATION Foamed-in-place polyurethane, 2” walls, 1
OPTIONAL • Leg set • Brass hardware Door finishes
ACCESSORIES & • Tapping kit • Caster sets Black vinyl coated
MODIFICATIONS • Laminated top • Base plates Stainless steel
• Laminated ends • Floor access kit Customers choice of laminate
3
/4” (629) 243/4” (629) 243/4” (629)
1
/2” (876) 341/2” (876) 341/2” (876)
1
1
/2” top.
/8” I.D. floor access kit-left rear corner.
Prepared for field lamination
Glass door with black vinyl coated frame
Glass door with stainless steel frame
Glass door with laminated frame
96” [2439] 4 DOOR
72” [1829] 3 DOOR
48” [1219] 2 DOOR
92” [2337] 4 DOOR
68” [1727] 3 DOOR
44” [1118] 2 DOOR
5-1/8”
[130]
6-3/16”
[157]
OPTIONAL
FLOOR
ACCESS
KIT 2”
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
23-1/2”
[597]
DOOR
19 7/8”
[505]
DOOR
OPENING
6-5/16”
[161]
4-1/2”
[107]
18-3/4” [476]
BACK LINER
TO INSIDE OF
DOOR SILL
R23-1/2”
31-1/4”
[794]
DOOR
HEIGHT
NOTE “A” 3/4” NPT DRAIN EXIT
NOTE “B” 1” NPS DRAIN ACCESS
6-3/8”
[163]
27-7/16”
[697]
DOOR
OPENING
22-3/4”
[578]
7-3/4”
3-7/16”
3
24-3/4”
[629]
[197]
[87]
4-3/16”
[106]
REFRIGERATION &
ELECTRICAL ACCESS
RIGHT OR LEFT
7-3/16”
[182]
34 1/2”
[876]
1-1/8”
[29]
NOTE “A”
Form No. Z2278
Page 4
Preparing the Cabinet for Use
Parts List
■
(2) Shelves plus (1) Floor Rack-per door.
■
Shelf Clips.
Suggested Tools
■
#2 Phillips Screwdriver.
■
10” Crescent Wrench.
9
■
16” Allen Wrench.
/
5
■
/16” and 3/8” Hex Socket.
■
Power Drill or Driver.
Plumbing
No plumbing required. Condensate from the cooling
coil is automatically evaporated through a condensate
pan located in the side condensing unit compartment.
Unit can be plumbed with a floor drain out rear right
corner
connection out side or bottom. Both drains are
plugged and can be removed if needed.
3
⁄4” NPT thread or bottom right 1” NPS thread
Placing the Cabinet
Push the cabinet into place using rollers when
necessary. Important: Proper air flow around the
condensing unit is necessary for efficient operation.
Never obstruct the air flow in and out of the
condensing unit.
For sanitation purposes, it may be necessary to
seal the base of the cabinet to the floor. This can be
accomplished by laying a bead of silicone sealant
between the base of the cabinet and the floor as
shown by the figure at below.
CABINET
BEAD SILICON
SEALER (RTV)
FLOOR
Electrical
The cabinet must be connected to a separately
fused power source (see electrical specification
plate) and grounded in accordance with National
and Local Electrical Codes. Caution: Do not
attempt to operate the equipment on any other
power source than that listed on the Electrical
Specification plate.
Uncrating and Inspection
Remove all crating material before operating.
Carefully inspect cabinet for hidden damage. If
damage is discovered, file your claim immediately
with the transportation company. Perlick is
not responsible for damage in transit.
Installing Casters or Legs
Attach four casters to the cabinet bottom; rigid casters at the rear and swivel casters on the front. Use
the supplied
machine screws.
1
/4”- 20 x 3/4” hex head self-tapping
(Optional)
Leveling the Cabinet
When the cabinet is in place, check installation with
carpenter’s level. When level front to back and left
to right, accumulated water will drain out of cabinet
evaporator drain.
Installing Base Plate (Optional)
Attach brackets to cabinet bottom in holes provided.
Attach base plate to brackets. (See separate
instructions, provided with kit). When returning
cabinet to upright position, be careful not to bend
brackets.
WARNING!
To avoid compressor damage,after returning
cabinet to an upright position, let unit stand for
24 hours before plugging it in and running the unit.
Form No. Z2278
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
4
Page 5
General Information
Refrigeration and Temperature Control
The Single Door Cooler cabinet is equipped with
a heavy-duty refrigeration system designed to
automatically maintain a storage temperature of
36-41 degrees F. The control is factory set at 38
degrees F.
4
3
COLDER
2
1
OFF
5
6
COLD
Adjusting the temperature
The temperature control is inside the cabinet on
the left-hand side of the evaporator fan panel
assembly. You will need a screwdriver to turn the
adjusting screw. Make small adjustments until the
desired temperature is achieved.
■
Colder Temperatures:
Turn the adjusting screw clockwise (to the right).
■
Warmer Temperatures:
Turn the adjusting screw counterclockwise
(to the left).
■
Temperature Control “OFF”:
Turn the adjusting screw completely counterclockwise to the “O” position until a click is
noted.
The condenser fan motor turns off and on with
the compressor. The evaporator fan motor is on
all the time.
NOTE:
Cabinet Temperatures lower than 34° will not allow
for proper defrosting of the evaporator coil. If
defrosting is necessary, turn the control knob to the
OFF position until coil is defrosted.
Cleaning the Cabinet
Use a mild detergent and water to clean the inside
and outside of the cabinet. Dry thoroughly. Never
use a scouring pad or abrasive cleanser.
NOTE: An industrial strength, commercial cleaner
can be used to clean the outside of painted
cabinets.
Cleaning the Condenser
Use a long handled, stiff brush to clean the dirt
from the front surface of the condenser. Keeping
the condenser free from dust and dirt will ensure
efficient operation.
CAUTION: Do not bend the fins while brushing the
front of the condenser.
Condenser
The condenser (located behind the front grille
cover) should be inspected every 30 days and
cleaned, if necessary.
Failure to keep the condenser clean will cause a
loss in condensing unit efficiency.
Recommended Cleaning Agents
JOB CLEANING AGENT* COMMENTS
Routine Cleaning Soap, ammonia, detergent Apply with sponge or cloth.
Can be used on all finishes.
Fingerprints and smears Areal 20, Lac-O-Nu, Lumin Wash, Provides barrier film to minimize
O’Cedar Cream Polish fingerprints. Can be used on all finishes.
Stubborn stains and Allchem Concentrated Cleaner, Rub lightly, using dry or damp
Discolorations Samae, Twinkle, Zud Restoro, cloth in the direction of polish
Grade F or FFF Italian Pumice, lines on the stainless steel.
Whiting or Talc, Liquid Nu Steel,
Copper’s or Revere Stainless Steel
Cleaner, Lumin Cleaner, Sta-Clean,
Cameo Copper Cleaner, Allen Polish
Highlite, Penny-Brite, Copper Brite
*
Use of propriety names is intended only to indicate a type of cleaner and does not constitute an endorsement.Omission of
any proprietary cleaner does not imply its inadequacy. All products should be used in strict accordance with instructions on
the package.
NOTE: Do Not Use Steel Wool or Scouring Pads to clean stainless steel.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
5
Form No. Z2278
Page 6
Replacement Parts — Custom Back Bar Cabinets
MODEL NOS. BS60 BS84 BS108
BR48 BR72 BR96
Condensing Units (BS Only)
Condensing unit 115 volt, 60 hz. C22647 C22646 C22646
Condensing unit 515301063 515301062 515301062
Compressor 513200314 513200003 513200003
Fan motor assembly 215315009 215315009 215315009
Condenser coil 15352019 15352019 15352019
Terminal board 219101538 219101538 219101538
Overload protector MRT20AGK5590 MRT22AGK5590 MRT22AGK5590
Relay 21351619 21351619 21351619
Capacitor 13556529 13556532 13556532
Evaproator Assembly
Self Contained (BS) complete 65555-1 65555-2 65555-2
Remote (BR) complete 65555-1R 65555-2R 65555-2R
Evaporator coil (BS) & (BR) C17511-1EP C17511-2EP C1751 1-2EP
Liquid & Suction line (BS) 65084 65085 65085
Fan blade 57699 57699 57699
Fan motor C15239A C15239A C15239A
Evaporator fan guard 65557 65557 65557
Temperature control 61283 61283 61283
Bulb clamp C6634 C6634 C6634
Wire harness, compressor bottom 65560 65560 65560
Wire harness, evaporator 65561 65561 65561
Wire harness, light jumper 65538 65539 65540
Wire harness, mullion heater 65571 65572 65573
Light bulb 63821 63821 63821
Light bulb guard 65525 65525 65525
Light socket 63484 63484 63484
Light switch 65535 65535 65535
Lock 63762 63762 36762
Space, lock 63761-1 63761-1 63761-1
Lock rail 65432-24SS or 65432-24 65432-24SS or 65432-24 65432-24SS or 65432-24
Grille rail 65432-12SS or 65432-12 65432-12SS or 65432-12 65432-12SS or 65432-12
Condenser pan 65565-1 65565-1 65565-1
Condenser end panel 66215-1SS 66215-1SS 66215-1SS
Grille, black 66210-12 66210-12SS 66210-12SS
Grille, SS 66210-12SS 66210-12 66210-12
Condenser housing back 65435-12SS 65435-12SS 65435-12SS
Evaporator, liquid & suction line cover 65576-1L 65576-2L 65576-3L
Evaporator pan 65526-1 65526-2 65526-2
Door sill 65500-1 65500-1 65500-1
Door handle bracket 65189-1 65189-1 65189-1
Door handle C31409-1 C31409-1 C31409-1
Door gasket 66237-4 66237-4 66237-4
Cabinet hinge 65436-LBRT 65436-LBRT 65436-LBRT
Cabinet hinge 65436-LBRB 65436-LBRB 65436-LBRB
Hinge pin 63679-1 63679-1 63679-1
Hinge assembly, cabinet left side 65505L 65505L 65505L
Hinge assembly, cabinet right side 65505R 65505R 65505R
End shelf kit 57928 57928 57928
Center shelf kit — 57929 57929
Left or right shelf 62307-2 62307-2 62307-2
Center shelf — 62308-2 62308-2
Vertical partition 61830-1 61830-1 61830-1
Pilaster strip C19271-1 C19271-1 C19271-1
Shelf clip C15875 C15875 C15875
Replacement door RD-NL2 RD-NL2 RD-NL2
*
Contact Perlick Milwaukee for complete door replacement. Cabinet serial no. required.
*
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2278
6
Page 7
Reversing Door Hinge
g
Tools Required
■
Phillips Screwdriver.
■
#4 Allen Wrench.
■
Flathead Screwdriver or Putty Knife
Right Hinged Door
(as shipped from factory)
Operations to Perform on Cabinet
STEP 1:
Remove bottom hinge pin from
assembly.
STEP 2:
Carefully lift and tilt out door
assembly from the unit and
set aside.
STEP 9:
Re-insert top hinge pin.
STEP 10:
Re-assemble lock rail from
STEP #3
Bottom Hinge Bracket
Operations to Perform on Door
Step #14
Top Hinge Bracket
STEP 3:
Remove lock rail from
cabinet, requires removal of
four screws.
Remove
these screws
STEP 4:
Remove top hinge pin.
Remove top and bottom hinge
brackets from the unit.
STEP 5:
Top Hinge Bracket
Bottom Hinge Bracket
Remove hinge bushing from
bottom hinge bracket and
assemble to top hinge bracket.
Hinge Bushin
STEP 6:
Taking care not to scratch the surface, remove hole plugs from the
left hinge holes.
STEP 7:
Insert hole plugs into vacant right
Step #7
Step #6
hinge holes
STEP 8:
Re-assemble hinge brackets to unit. Bottom right bracket
is assembled as the top left bracket. Top right bracket is
assembled as the bottom left bracket.
Step #12 Step #11 Step #13
STEP 11:
Remove bottom door hinge bracket from door assembly
and remove door hinge bushing from bracket.
Re-assemble door hinge bracket to previous position,
without bushing.
STEP 12:
Remove top door hinge bracket from door assembly and
assemble door hinge bushing from STEP 11 to bracket.
Re-assemble door hinge bracket to previous position
with bushing attached.
STEP 13:
Remove handle and reposition in other set of pre-drilled
mounting holes directly underneath..
STEP 14:
Remove lock retainer and install on opposite end of
door..
STEP 15:
What was the door top is now the door bottom. Carefully
lift the door onto the hinge brackets of the cabinet. The
two hinge bushings should meet. reinsert the bottom
hinge pin to complete the door switching operation.
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
7
Form No. Z2278
Page 8
Wiring Diagram – Custom Back Bar Cabinets
[2] DOOR
MULLION HEATER MULLION HEATER MULLION HEATER
BLACK
WHITE
EVAPORATOR FAN EVAPORATOR FAN
EVAPORATOR
HOUSING
GROUND WIRE
BLACK
GREEN
POWER CONNECTION
WHITE
WHITE
BLACK
WHITE
BLACK
GREEN
JUNCTION BOX
LIGHT SWITCH
BLACK
WHITE
BLACK
RED
CABINET
JUNCTION BOX
PRESSURE SWITCH
BS Series Self-Contained
[3] DOOR [4] DOOR
RED
WHITE
BLACK
WHITE
LIGHT LIGHT LIGHT
THESE WIRES CAPPED IN
SINGLE CABINET
INSTALLATIONS
NOTE:
FIELD WIRING FROM CABINET
JUNCTION BOX TO CONDENSING
UNIT MUST COMPLY WITH ALL
LOCAL AND NATIONAL ELECTRICAL
CODES.
CONDENSING UNIT
FIELD INSTALLED
2, 3 and 4 Door
BR Series Remote
2, 3 and 4 Door
LIGHT
[2] DOOR
MULLION HEATER MULLION HEATER MULLION HEATER
RED
BLACK
LIGHT SWITCH
WHITE
BLACK
LIGHT LIGHT LIGHT
WHITE
BLACK
WHITE
EVAPORATOR FAN EVAPORATOR FAN
WHITE
[3] DOOR
[4] DOOR
LIGHT
THERMOSTAT
CONDENSING UNIT
POWER CONNECTION
BLACK
WHITE
GREEN
WHITE
BLACK
GREEN
JUNCTION BOX
BLACK
RED
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069
Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.
Form No. Z2278
8
Loading...