Pentax TS812E, HS614E, TS812EDW, TS412EDW, HS316E Owners manual

ENGLISH ON THE BACK

■

/
TS212E	TS412E	TS812E
TS212EDW	TS412EDW	TS812EDW
/
HS316E	HS614E	HS1214E

います。ご使用の前にこの取扱説明書を必ずお読みいただき、正しくお使いく ださい。お読みになった後は、いつでも見られるところに保管してください。

■

とを示す」内容です。

■

■

ありますので、カメラの取扱説明書をご覧ください。

回転させしっかりと締め付けてください。

320°

2 36 9 174-8639

Tel.[phone] Fax.[phone]

3170407-Z2-2 (J) S3095076

■

のうえ、コネクターを接続してください。

		JEITA EIAJ RC-5204
1	( ) -
2	+
3	( ) +
4	( ) -

■

説明書をご覧ください。

■

ントが合わせられない場合は、カメラの取扱説明書をご覧になり次の 手順でカメラのバックフォーカスを調整してください。

ND

を調整しピントを合わせてください。

■

CE EU EMC EN50130-4 EN55022

■

■

■

TS212E TS412E TS812E HS316E HS614E HS1214E TS212EDW TS412EDW TS812EDW

■

	TS212E TS212EDW	TS412E TS412EDW	TS812E TS812EDW
	2.8mm	4mm	8mm
	F1.2 F200	F1.2 F200	F1.2 F200
	0.3m	0.2m	0.3m
		200Ω±10 25
		700Ω±10 25
		4
	0.5
		20 50
	HS316E	HS614E	HS1214E
	3.7mm	6mm	12mm
	F1.6 F300	F1.4 F300	F1.4 F300
	0.2m	0.2m	0.5m
		230Ω±10 25
		730Ω±10 25
		4
	0.5
		20 50

Auto-Iris Mono-Focal Lens Operating Instructions

■ Model number

1/3 format CS mount
TS212E	TS412E	TS812E
TS212EDW	TS412EDW	TS812EDW
1/2 format CS mount
HS316E	HS614E	HS1214E

Thank you for choosing PENTAX CCTV lenses. Before operating this lens, please read these instructions carefully. After reading this Operating Instructions, keep it for future reference.

■ For your safety on use of a lens

Before operating, pay special attention to the following remarks.

WARNING	CAUTION
This alerts users to the possible	This alerts users to the possible risk
risk of personal harm.	of personal and material harm.

This is a warning to users.

This is to caution users.

WARNING

Do not look at the sun through the lens with the naked eye. Loss of eyesight may occur.

Do not disassemble, repair or modify the lens.

Fire, electric shocks or malfunction may occur.

If the lens emits smoke, smells of smoke or gives off heat, discontinue use immediately. Fire or electric shocks may occur.

Do not damage, bend, twist or pull on the cable. Fire, electric shocks or malfunction may occur.

CAUTION

Do not leave unused lenses in direct sunlight. Fire may occur.

Mount the lens firmly on a camera, so that it will not loosen and fall off.

Do not install the lens in a place where vibration and shock are expected. It may come loose and fall off.

■ Precautions

•Do not use organic solvents, such as thinners, alcohol or benzine to remove stains from the lens.

•Use a blower or a clean lens brush to remove dust. When grease or fingerprints are on the lens, wipe them off with a lens cleaning paper and lens cleaner gently forming a swirl from the center to the circumference.

•Connect the cable properly referring to the following list entitled "Auto-iris Cable connections".

•This lens is a precision optical product. Avoid dropping, strong vibration, shock and pressure on it.

•Keep the lens away from dust, poisonous gas, moisture and salt. It may cause lens malfunction.

■ Mounting and removing the lens

Before mounting the lens, confirm the camera mount matches the lens. This lens cannot be used on a C mount camera.

Some cameras are C and CS mount compatible. Refer to the Operating Instructions of the camera.

Screw the lens clockwise into the camera.

Eventually, the clutch of the lens will start slipping. Keep turning the lens until the clutch reaches its stop.

The lens position is now adjustable counter-clockwise in about 320 degrees. Turn the lens until the correct position is achieved.

HOYA CORPORATION

PENTAX Imaging Systems Division

Security Systems Sales Department

When removing the lens, keep turning the lens counter-clockwise until the lens comes off.

■ Auto-iris Cable connections

Installation of the auto iris Cable. This is a DC Drive iris lens.

Pin No.	Color/Specifications		This pin configuration is
1	Blue or Brown/Damping Coil -		conforming to JEITA*
			Standard.
2	Red	/Damping Coil +
3	White or Yellow/Driving Coil +
4	Green or Orange/Driving Coil -

* Japan Electronics and Information Technology Industries Association

■ Iris adjustment

This is a DC Drive iris lens. Please refer to Operating Instructions of the camera.

■ Adjusting back focus

The flange back of this lens is factory adjusted for CS mount camera. In case you are unable to focus either at the shortest or longest focal lengths, adjust the back focus of the camera by the following method, referring to the Operating Instructions of the camera.

Fully open the iris by either of the following methods.

Set the auto electronic shutter of the camera to On.

Cover front of the lens with a ND filter according to the prevailing lighting conditions. The brighter the lighting conditions, a higher ND factor is required.

Observe an image of a distant object. (Over 10m is recommended.)

Set the focus ring at [FAR] position, and then adjust back focus of the camera.

■ marking

The lenses having CE marking on their bodies are conformity with the standards EN50130-4 and EN55022 related to EMC directives by EU.

■ After-sales servicing

Contact your supplier for after-sales servicing.

■ Composition

Lens body	Front cap	Rear cap
Operating instructions

■ External view

TS212E TS412E TS812E HS316E HS614E HS1214E TS212EDW TS412EDW TS812EDW

■ Main specifications

Model number	TS212E		TS412E		TS812E
	TS212EDW		TS412EDW		TS812EDW
Focal length	2.8mm		4mm		8mm
Iris range	F1.2 F200		F1.2 F200		F1.2 F200
Min.object distance	0.3m		0.2m		0.3m
Driving coil			200Ω±10 25
Damping coil			700Ω±10 25
Driving voltage		+4V or less (Close to Open)
		Over 0.5V (Open to Close)
Temperature range			-20 - +50
Model number	HS316E		HS614E		HS1214E
Focal length	3.7mm		6mm		12mm
Iris range	F1.6 F300		F1.4 F300		F1.4 F300
Min.object distance	0.2m		0.2m		0.5m
Driving coil			230Ω±10 25
Damping coil			730Ω±10 25
Driving voltage		+4V or less (Close to Open)
		Over 0.5V (Open to Close)
Temperature range			-20 - +50

2-36-9, Maeno-cho, Itabashi-ku, Tokyo 174-8639, Japan

Phone [phone] Fax. [phone]

3170407-Z2-2 (E) S3095076