ENGLISH ON THE BACK
■
TS2V114E
います。ご使用の前にこの取扱説明書を必ずお読みいただき、正しくお使いく ださい。お読みになった後は、いつでも見られるところに保管してください。
■
|
|
とを示す」内容です。
■
■
ありますので、カメラの取扱説明書をご覧ください。
340°
B
2 36 9 174-8639
Tel.03-3960-0336 Fax.03-3960-0337
3170100-Z2-1 (J) S3095021
③
|
|
■
のうえ、コネクターを接続してください。
|
|
JEITA EIAJ RC-5204 |
1 |
- |
|
2 |
+ |
|
3 |
+ |
|
4 |
- |
|
■
説明書をご覧ください。
■
遠端、広角端のどちらかでピントが合わせられない場合は、カメラの 取扱説明書をご覧になり次の手順でカメラのバックフォーカスを調整 してください。
ND
にし、カメラのバックフォーカスを調整しピントを合わせます。
フォーカス調整を行い、ピント合わせが可能か確認してください。
■
CE EU EMC EN50130-4 EN55022
■
■
■
■
|
1 3 |
|
CS |
|
1.6mm 3.4mm |
|
F1.4 F64 |
|
0.5m |
|
200Ω±10 25 |
|
700Ω±10 25 |
|
4 |
|
0.5 |
|
20 50 |
Auto-Iris Fish Eye Vari-Focal Lens Operating Instructions
■ Model number
TS2V114E
Thank you for choosing PENTAX CCTV lenses. Before operating this lens, please read these instructions carefully. After reading this Operating Instructions, keep it for future reference.
■ For your safety on use of a lens
Before operating, pay special attention to the following remarks.
WARNING |
CAUTION |
This alerts users to the possible |
This alerts users to the possible risk |
risk of personal harm. |
of personal and material harm. |
This is a warning to users.
This is to caution users.
WARNING
Do not look at the sun through the lens with the naked eye. Loss of eyesight may occur.
Do not disassemble, repair or modify the lens.
Fire, electric shocks or malfunction may occur.
If the lens emits smoke, smells of smoke or gives off heat, discontinue use immediately. Fire or electric shocks may occur.
Do not damage, bend, twist or pull on the cable. Fire, electric shocks or malfunction may occur.
CAUTION
Do not leave unused lenses in direct sunlight. Fire may occur.
Mount the lens firmly on a camera, so that it will not loosen and fall off.
Do not install the lens in a place where vibration and shock are expected. It may come loose and fall off.
■ Precautions
•Do not use organic solvents, such as thinners, alcohol or benzine to remove stains from the lens.
•Use a blower or a clean lens brush to remove dust. When grease or fingerprints are on the lens, wipe them off with a lens cleaning paper and lens cleaner gently forming a swirl from the center to the circumference.
•Connect the cable properly referring to the following list entitled "Auto-iris Cable connections".
•This lens is a precision optical product. Avoid dropping, strong vibration, shock and pressure on it.
•Keep the lens away from dust, poisonous gas, moisture and salt. It may cause lens malfunction.
■ Mounting and adjusting optical axis
Before mounting the lens, confirm the camera mount matches the lens. This lens cannot be used on a C mount camera.
Some cameras are C and CS mount compatible. Refer to the Operating Instructions of the camera.
Adjusting lens position
Screw the lens clockwise into the camera.
Rotate the lens further until it stops and firmly mount the lens on the camera.
The lens position is adjustable counter-clockwise in about 340°.
Rotate the lens to correct position.
When removing the lens, keep turning the lens counter-clockwise until the lens comes off.
Adjusting optical axis
Loosen 3 shift-locking screws.
Set the zoom ring at the widest [FISHEYE] position and using a TV monitor physically shift the lens body against its mount to produce an image as illustrated in Figure B.
HOYA CORPORATION
PENTAX Imaging Systems Division
Security Systems Sales Department
2-36-9, Maeno-cho, Itabashi-ku, Tokyo 174-8639, Japan
Phone +81-3-3960-0347 Fax. +81-3-3960-0337
3170100-Z2-1 (E) S3095021
Tighten 3 shift-locking screws tentatively and softly.Finally tighten the screws by turns.
Figure A |
Figure B |
■ Auto-iris Cable connections
Installation of the auto iris Cable. This is a DC Drive iris lens.
Pin No. |
Color/Specifications |
This pin configuration is |
|
|
|
conforming to JEITA* |
|
1 |
Blue/Damping Coil - |
||
|
|
Standard. |
|
2 |
Red/Damping Coil + |
||
|
|||
3 |
White/Driving Coil + |
|
|
4 |
Green/Driving Coil - |
|
* Japan Electronics and Information Technology Industries Association
■ Iris adjustment
This is a DC Drive iris lens. Please refer to Operating Instructions of the camera.
■ Adjusting back focus
The flange back of this lens is factory adjusted for CS mount camera. In case you are unable to focus either at the shortest or longest focal lengths, adjust the back focus of the camera by the following method, referring to the Operating Instructions of the camera.
Fully open the iris by either of the following methods.
Set the auto electronic shutter of the camera to On.
Cover front of the lens with a ND filter according to the prevailing lighting conditions. The brighter the lighting conditions, a higher ND factor is required.
Observe an image of a distant object. (Over 10m is recommended.)
Set the zoom ring at [WIDE] position and the focus ring at [FAR] position, and then adjust back focus of the camera.
Make focus adjustments with the focusing ring, confirming that objects are in focus across the entire zoom range, especially at the [WIDE] and [FISHEYE] positions.
■ marking
The lenses having CE marking on their bodies are conformity with the standards EN50130-4 and EN55022 related to EMC directives by EU.
■ After-sales servicing
Contact your supplier for after-sales servicing.
■ Composition
Lens body |
Front cap |
Rear cap |
Operating instructions |
|
■ External view
■ Main specifications
Format size |
1/3 |
|
Mount |
CS |
|
Focal length |
1.6mm 3.4mm |
|
Iris range |
F1.4 F64 |
|
Min.object distance |
0.5m |
|
Driving coil |
200Ω±10 25 |
|
Damping coil |
700Ω±10 25 |
|
Driving voltage |
+4V or less (Close to Open) |
|
Over 0.5V (Open to Close) |
||
|
||
Temperature range |
-20 - +50 |