DEFENDER CSC-LINK
PENTEK
INSTALLATION AND
OPERATION MANUAL
pentair.com
PN1053 (10-18-19)
TABLE OF CONTENTS
SECTION .................................................................................................................................................................................................. PAGE
General Information ............................................................................................................................................................................. 3-4
Installation ............................................................................................................................................................................................ 5-7
Troubleshooting ....................................................................................................................................................................................8-9
Warranty .................................................................................................................................................................................................10
GENERAL INFORMATION
READ AND FOLLOW SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this symbol on
your pump or in this manual, look for one of the following signal
words and be alert to the potential for personal injury:
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
personal injury, death or major property damage if ignored.
personal injury or property damage if ignored.
NOTICE: indicates special instructions which are important but
not related to hazards.
• Carefully read and follow all safety instructions in this manual
and on pump.
• Keep safety labels in good condition.
• Replace missing or damaged safety labels.
• Make workshops childproof; use padlocks and master
switches; remove keys.
instructions. Failure to follow the instructions and warnings in
the manual may result in serious or fatal injury and/or property
damage, and will void the product warranty. This product must
be installed by a qualified professional. Follow all applicable
local and state codes and regulations. In the absence of such
codes, follow the current editions of the National Plumbing Code
and National Electrical Code (NEC), as applicable.
containing a tank under pressure, which may over time corrode,
weaken and burst or explode, causing serious or fatal personal
injury, leaking or flooding and/or property damage. To minimize
risk, a licensed professional must install and periodically inspect
and ser vice the product and system. A drip pan connected to
an adequate drain must be installed if leaking or flooding may
cause property damage. Do not locate system in an area where
leaking may cause property damage.
to pressures that may exceed the limitations of system
components. Never set the operating pressure higher than that
of the safe system capacity.
differential. An improperly sized tank can cause the pump
to cycle and lead to pump damage. This may require a larger
pressure tank than is normally used.
warns about hazards that can cause serious
warns about hazards that will or can cause minor
Read carefully the product installation & operation
This product is used in conjunction with a system
This control is capable of running pumps
This control can be adjusted to a narrow pressure
ELECTRICAL SAFETY
ELECTROCUTION HAZARD: Must be installed by
a qualified professional. First disconnect all electrical power
before attempting service. For your safety, the installation and
operation instructions must be followed to minimize the risk of
electric shock, property damage or personal injury.
GENERAL SAFETY
Do not touch an operating motor. Modern
motors can operate at high temperatures. To avoid burns when
servicing pump, allow it to cool for 20 minutes after shutdown
before handling.
• Do not allow pump or any system component to freeze. To do
so will void the warranty. See “Warranty” on Page 10.
• Pump only water with this pump.
• Periodically inspect pump and system components.
• Wear safety glasses at all times when working on pumps.
• Keep work area clean, uncluttered and properly lighted. Store
all unused tools and equipment.
• Keep visitors at a safe distance from the work areas.
unless a relief valve capable of passing full pump flow at 75 psi is
installed.
of any water treatment equipment. The water quality can
significantly influence the life of your system. You should
test for corrosive elements, acidity, total solids and other
relevant contaminants, including chlorine and treat your water
appropriately to ensure satisfactory performance and prevent
premature failure.
sweat-solder connections, as required by state and federal
codes.
must be installed to prevent pressure in excess of local code
requirement or maximum working pressure designated in the
product manual, whichever is less. Do not expose system to
freezing temperatures or temperatures in excess of 120°F
(49°C). Failure to properly size the system or follow instructions
in the manual may result in excessive strain on the system and
may lead to product failure, leakage, flooding and/or property
damage.
Pump body may explode if used as a booster pump
A water test must be taken before installation
Use only lead-free solder and flux for all
EXPLOSION OR RUPTURE HAZARD: A relief valve
CALIFORNIA PROPOSITION 65 WARNING
This product and related accessories contain
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
3
PN1053 (10-18-19)
Loading...