Pella 808SQ102 User Manual
©2008 Pella Corporation
Part Number: 808S0102
INSTALLATION INSTRUCTIONS -
INSTRUCCIONES DE INSTALACIÓN
CLAD SLIDING PATIO DOOR - SOUTHWESTERN WALL WITH HARD
COAT STUCCO
PUERTA PARA PATIO CORREDIZA, PARA PARED ESTILO SUREÑO
CON ESTUCO DE CAPA BASE
Lea las instrucciones en español en el reverso.
Installation Instructions for Typical Wood Frame Construction.
These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water.
These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods,
multiple units or bow and bay windows, may be obtained from Pella® Corporation or a local Pella retailer. Building designs, construction methods,
building materials, and site conditions unique to your project may require an installation method different from these instructions and additional
care. Determining the appropriate installation method is the responsibility of you, your architect, or construction professional.
YOU WILL NEED TO SUPPLY:
• Cedar or Impervious shims/spacers (12 to 20)
• 2" galvanized roofing nails (1/4 lb.)
• Closed cell foam backer rod/sealant backer (12 to 30 ft.)
®
• Pella
SmartFlash™ foil backed butyl window and door
flashing tape or equivalent
• High quality exterior grade polyurethane or silicone sealant
(2 to 3 tubes per door)
• Great Stuff
by the Dow Chemical Company or equivalent low pressure
polyurethane window and door foam - DO NOT use high
pressure or latex foams.
• Pella aluminum sill support or 2 x 4 wood blocking
• Interior trim and/or jamb extensions (15 to 40 ft.)
• 9" wide Fortifiber flashing paper or equivalent
™
Window and Door Insulating Foam Sealant
4&"-"/5
4&"-"/5
TOOLS REQUIRED:
• Tape measure
• 6' Level
• Square
• Hammer
• Stapler
• Sealant gun
• Scissors or utility knife
• Drill
• Screwdrivers
(#2 Phillips with 8" shaft and small flat blade)
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
XJEF'MBTIJOHQBQFS
'JO
$PSOFS
/BJMJOH'JO
5PQ
'MBTIJOH
4JEF
5BQF
'MBTIJOH
5BQF
*OUFSMPDLFS
4JEF
'MBTIJOH
5BQF
'
M
B
T
I
J
O
H
1
B
Q
F
S
'MBTIJOH1BQFS
4JMM4VQQPSU
'
M
B
T
I
J
O
H
1
B
Q
F
S
4JMM'MBTIJOH5BQF
4JMM'MBTIJOH5BQF
Always read the Pella® Limited Warranty before purchasing or installing Pella products. By installing this product, you are acknowledging
that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product
warranty. See Limited Warranty for complete details at http://warranty.pella.com.
1 ROUGH OPENING PREPARATION
A. Confirm the opening is plumb and level.
Note: It is critical that the bottom is level.
B. Confirm the door will fit the opening. Measure all four sides of the opening to
make sure it is 3/4" larger than the door in width and 1/2" larger in height. Measure
the width at the top, bottom, and center. Measure the height at the far left side, the
far right side, and in the center.
Note: 1-1/2" or more of solid wood blocking is required around the perimeter of
the opening. Fix any problems with the rough opening before proceeding.
C. Apply flashing paper at the bottom (1C). Cut one piece of flashing paper 18" longer
than the width of the rough opening. Position the top edge of the flashing paper with
the top of the sill plate. Center the flashing paper with the opening width. Staple the
flashing paper to the sill plate.
Note: Bottom flashing paper is not required for installation on concrete floors.
£
£
D. Apply flashing paper to the sides of the rough opening (1D). Cut two pieces of
flashing paper 18" longer than the height of the rough opening. Apply one piece to
each jamb. Position the edge of the flashing paper with the inside edge of the trimmer
(jack stud), and center the flashing paper with the height of the rough opening. Staple
the flashing paper to the trimmer.
E. Apply bottom flashing tape #1. Cut a piece of flashing tape 12" longer than the opening
width. Apply at the bottom of the opening as shown (1E) so it overhangs 1" to the exterior.
Note: The tape is cut 12" longer than the width of the opening so that it will extend up
each side approximately 6".
F. Tab the bottom flashing tape and fold. Cut 1" wide tabs at each corner (1/2" from each side
of corner) (1F). Fold tape to the exterior and press firmly to adhere it to the flashing paper.
G. Apply bottom flashing tape #2. Cut a piece of flashing tape 12" longer than the opening
width. Apply at the bottom, overlapping tape #1 by at least 1". DO NOT allow the tape to
extend past the interior face of the framing (1G).
Note: The flashing tape does not need to extend all the way to the interior of the framing.
£
£
£
£
£
H. Attach the aluminum sill support or wood blocking to the exterior of the box plate
to support the edge of the door sill. Place the sill support flush with the subfloor.
£
Loading...