Pella 206K0000 Users Manual

Insynctive™ WOOD VENETIAN BLIND
Product Guide

WOOD BLIND OVERVIEW:

Pella® Wood Blinds can raise, lower or tilt for flexible light or privacy control — all with the press of
a button. WOOD BLIND may be controlled with SINGLE CHANNEL REMOTE, a compatible security, or a
home automation system. Three custom positions may be programmed to WOOD BLIND including an
Upper Position, User Position, and Lower Position.

TOOLS REQUIRED

Measuring Tape
Drill with 3/32” Bit and 1/4” Nut Driver
Pencil
#2 Phillips Head Screwdriver
Flat Head Screwdriver
Level

INSTALLATION AND SETUP INSTRUCTIONS

1. Get Started

Verify package contents match the packing slip
Verify there are no obstructions in the path the shade will travel such as latches, locks, window

crank, handles, sensors, window mullions, etc.

2. Determine Mount Type

Determine whether you will use an Outside Mount or Inside Mount.

3. Install Shade

Measure 6 inches inward from each side of the opening. Mark with a pencil. If your shade has

more than two brackets, the remaining brackets must be distributed evenly between the two
marks. Temporarily place each bracket and mark the screw holes.

Drill holes at the marked locations using a 3/32” bit.
Align bracket and bracket spacer with drilled holes and drive a screw into each hole with a 1/4”

nut driver. Use expansion anchors or toggle bolts if adequate structure is not present in the
mounting area. Repeat for each bracket.

Hook the shade on the brackets by sliding the top leg of the brackets into the top of the shade,

then pressing up at an angle until the shade snaps into the bracket. Inspect behind the shade to
ensure that the shade assembly is secured to each bracket.

4. Setup WOOD BLIND

Complete the following steps to setup WOOD BLIND

a. Remove the front plastic cover and install provided D cell batteries. You have one minute to

complete the next step.

b. Press and hold UP button on REMOTE until WOOD BLIND completes a quick down/up

motion. This will require the UP button to be pressed for about 5 seconds. WOOD BLIND
will then move back to the top, fully open position.

c. When WOOD BLIND stops in the fully open position, press and release the DOWN button to

send the WOOD BLIND to its Lower Position. If the preset Lower Position is satisfactory, you
may skip the remaining setup steps.

d. To change the Lower Position, simultaneously press and hold the CENTER and DOWN

buttons until WOOD BLIND completes a quick up/down motion. This will require the
buttons to be pressed for about 5 seconds. The light on the remote will begin blinking to
acknowledge that the remote is in Program Mode.

e. Pull Bottom Rail downward at least 5 inches to select WOOD BLIND. WOOD BLIND will

complete a quick up/down motion to acknowledge it is ready to learn a new position.

f. Pull the Bottom Rail downward to the desired position. If you pull the Bottom Rail too far,

you may raise it in incremental steps by tapping the UP button.

g. Press and hold the CENTER button until WOOD BLIND makes a quick up/down movement.

This should take about 5 seconds. The light on the remote will stop blinking.

h. WOOD BLIND is now ready for use.

5. Test WOOD BLIND

Press the UP button to move WOOD BLIND to the fully open position. Verify that WOOD BLIND

does not rub or interfere with window, wall, or other obstructions.

Press the DOWN button to move WOOD BLIND to the down position. Verify fabric appears

straight, level, and that the gaps or overlaps are equal. Safely make adjustments to the brackets
as needed.

PROGRAMMING POSITIONS

REMOTE CONTROL may be used to teach up to three positions to Insynctive WOOD BLIND; including an
Upper Position, User Position, and Lower Position. Once placed into program mode, REMOTE CONTROL
will stay in program mode until the programming process is completed or REMOTE will automatically
exit program mode if no buttons are pressed for 1 minute or if battery is removed and re-inserted.

Programming Upper Position

Simultaneously press and hold the CENTER and UP buttons until WOOD BLIND completes a quick

up/down motion. This will require the buttons to be pressed for about 5 seconds. The light on the
remote will begin blinking when the buttons are released to acknowledge that the remote is in
Program Mode.

Pull WOOD BLIND Bottom Rail downward at least 5 inches to select WOOD BLIND. WOOD BLIND will

complete a quick up/down motion to acknowledge it is ready to learn a new position.

Press the UP or DOWN buttons on REMOTE to move WOOD BLIND Bottom Rail to the desired

position.

Press and hold the CENTER button until WOOD BLIND makes a quick up/down movement. This

should take about 5 seconds. The light on the remote will stop blinking.

Programming User Position

Simultaneously press and hold the UP and DOWN buttons until WOOD BLIND completes a quick

up/down motion. This will require the buttons to be pressed for about 5 seconds. The light on the
remote will begin blinking when the buttons are released to acknowledge that the remote is in
Program Mode.

Pull WOOD BLIND Bottom Rail down at least 5 inches to select WOOD BLIND and cause it to enter

Program Mode. WOOD BLIND will complete a quick up/down motion to acknowledge it is selected
and has entered Program Mode.

Press the UP or DOWN buttons on REMOTE to move WOOD BLIND Bottom Rail to the desired

position. NOTE: User position must be set between the Upper and Lower Positions or it will
automatically default to a position in between the Upper and Lower Positions when it is saved.

Press and hold the CENTER button until WOOD BLIND makes a quick up/down movement. This

should take about 5 seconds. The light on the remote will stop blinking.

Programming Lower Position

Simultaneously press and hold the CENTER and DOWN buttons until WOOD BLIND completes a

quick up/down motion. This will require the buttons to be pressed for about 5 seconds. The light
on the remote will begin blinking when the buttons are released to acknowledge that the remote is
in Program Mode.

Pull WOOD BLIND Bottom Rail down at least 5 inches to select WOOD BLIND and cause it to enter

Program Mode. WOOD BLIND will complete a quick up/down motion to acknowledge it is selected
and has entered Program Mode.

Pull the Bottom Rail downward to the desired position. If you pull the Bottom Rail too far, you may

raise it in incremental steps by tapping the UP button.

Press and hold the CENTER button until WOOD BLIND makes a quick up/down movement. This

should take about 5 seconds. The light on the remote will stop blinking.

OPERATING SHADE WITH REMOTE

Press and Release UP Button: Pressing the UP button for less than 1 second will cause WOOD BLIND

to automatically move to the Upper Position.

Press and Release Center Button: Pressing the CENTER button for less than 1 second will cause

WOOD BLIND to automatically move to the User Defined Position that has been programmed by the
user.

Press and Release DOWN Button: Pressing the DOWN button for less than 1 second will cause

WOOD BLIND to automatically move to the Lower Position that has been programmed by the user.