Pelco SWM-GY, SWM-SR User Manual

INSTALLATION

SWM Series Wall Mount

C293M-E (9/13)

Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical Box Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 C293M-E (9/13)

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Installation should be done only by qualified personnel and conform to all local codes.
7. Use only installation methods and materials capable of supporting four times the maximum specified load.
8. Only use replacement parts recommended by Pelco.
9. Use stainless steel hardware to fasten the mount to outdoor surfaces.
10. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.
C293M-E (9/13) 3

Description

The SWM Series indoor/outdoor wall mounts are designed primarily for use with Pelco pendant domes including Spectra®, DF5, and Sarix® ID and IE Series. They can also be used with other pendant domes that require a 3.8 cm (1.5-inch) NPT pipe thread for installation. The mount features cable feedthrough that conceals electrical wiring in the pendant component. The sun shield used for outdoor versions of the pendant component (where available) is readily accepted by the mount. Anti-seize lubricant is supplied for application to the pipe threads, and a gasket is affixed to the base to protect the interior from moisture.
The mount can be attached to any vertical load-bearing surface or to either an SWM-PA Series pole adapter or an SWM-CA Series corner mount adapter by means of a mounting cleat.
The wall mount and adapters are constructed of aluminum with a polyester powder coat finish. The wall mount is available in gray, light gray, black, or white. The pole adapter is available in gray, black, or white. The corner adapter is available in gray or white.
For Sarix installations, the SWM Series wall mounts require a Sarix pendant mount adapter: the ID-P is required for Sarix ID Series domes and the IE-P is required for Sarix IE Series domes.

MODELS

SWM-GY Wall mount with cable feedthrough; gray finish SWM-BK Same as SWM-GY except black finish SWM-SR Same as SWM-GY except light gray finish SWM-WT Same as SWM-GY except white finish

PARTS LIST

Qty Description
1 Wall mount 1 Mounting cleat 1 Adjustment plate 1 10-24 x 1.59 cm (0.625-inch) set screw (attached) 1 Anti-seize lubricant
The following parts are needed but not supplied:
Qty Description
2 Mounting fasteners, up to 0.64 cm (0.25-inch) (M6) diameter, appropriate length for
attaching the mounting cleat to the wall or adjustment plate
2 Mounting fasteners, up to 0.64 cm (0.25-inch) (M6) diameter, appropriate length for
attaching the adjustment plate to an electrical box
1 Pendant component (dome, back box, adapter)
4 C293M-E (9/13)
Loading...
+ 8 hidden pages