Thank you for purchasing Pelco’s Spectra III™ SE/Spectra III™ Series dome system. This manual provides the information required to
set up and install the dome drive. Please thoroughly familiarize yourself with the information in this manual before attempting
installation.
NOTE: This manual does not contain instructions for installing a complete Spectra III SE/Spectra III Series system. For complete
instructions refer to the installation packet shipped with the back box.
SETUP FOR COAXITRON PROTOCOL
No DIP switch settings are required for Coaxitron control. Proceed to
Dome Drive Installation
on page 4.
SETUP FOR D AND P SERIES PROTOCOL
PROTOCOL SETTINGS
The Spectra III SE and Spectra III Series dome drives automatically detect type of protocol. No switch settings are required to set
Coaxitron®, RS-422 P and D Series protocols.
SWITCH SETTINGS
NOTE: If you have a Spectra III EVS dome system, make sure the
switches are in their default positions (refer to Figure 1). The
switches configure the dome for address 1 (D-type control),
2400 baud, and no termination. Proceed to
on page 4.
Dome Drive Installation
1
Before installing the dome drive, configure the receiver address,
termination, and baud setting. The DIP switches, to configure these
settings, are located on the side of the dome drive.
Figure 1 shows the default settings for the DIP switches. Switch SW1-1 (SW1, switch 1) is set to the ON position. All other switches
are set to the OFF position.
Refer to the following sections to set the address, termination, and baud setting for the dome drive.
SW1–Receiver Address
Set the SW1 switches for the address of the dome drive. The following information is required to set the dome drive address:
SW1-1 is set to the ON position.
All other switches are set to the OFF position.
3
2
1
SW2
onon
1
SW3
8
7
6
5
4
3
2
SW1
Figure 1. Default Switch Settings
8
7
6
5
4
ON
P-Type ControlDefault address is 2. Refer to Table A for address settings that use P-Type control. Maximum number of
receivers is 32.
D-Type ControlDefault address is 1. Refer to Table B for address settings that use D-Type control. Maximum number of
receivers is 254.
NOTE: Coaxitron Control - No address settings are required.
2C2472M-A (12/05)
Page 3
SW2–Termination Setting
When connecting more than one Spectra dome to a single controller, terminate the unit farthest from the controller. Termination is
only required for the last dome in the series.
The dome drive is shipped from the factory in the unterminated (OFF) position. To terminate the dome drive, set the SW2 switch to
the ON position.
NOTE: Coaxitron Control - Dome termination is not required.
SW3–Baud Settings
Pelco’s D-Type controllers are set for 2400 baud. The default setting for the dome drive is 2400 baud. If you are using a Pelco D-Type
controller, do not reset the SW3 switches.
P-Type controllers can operate at 2400, 4800, and 9600 baud. Set the SW3 switches (6, 7, and 8), located on the side of the dome
drive, to the same baud as the P-type controller.
Switch NumberSW3-6SW3-7SW3-8
2400 Baud (default)OffOffOff
4800 BaudOnOffOff
9600 BaudOffOnOff
NOTE: Coaxitron Control - Configuring the baud setting is not required.
Special System Settings
AD-32 Preset System
SW3-1 should be set to the ON position if an AD-32 controller and Pelco’s TXB-AD translator board are used to control the dome
system.
CM9502 Setting
If a CM9502 matrix system is used with the dome drive, set SW3-2 to the ON position.
C2472M-A (12/05)3
Page 4
DOME DRIVE INSTALLATION
Install the dome drive. Line up the blue (A) and red (B) tabs with the blue (A) and red
(B) labels. Push the tabs in. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click into place. Refer to Figure 2.
To use your dome system, refer to the Operation and Programming Manual supplied
with the dome drive.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #DateComments
C2472M 2/03Initial release.
C2472M-A12/05Added note for Spectra III EVS dome system. Added WEEE statement.
C2472M-A (12/05)7
Page 8
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
United States
Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East
|
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.