Pelco LRD41C-CONNKIT User Manual

LRD41C-CONNKIT
for LRD41C21-*/LRD41C22-* Receiver/Driver
C559M (5/97)
Installation Instructions

The LRD41C-CONNKIT is required to enable alarm and auxiliary functions of the
receiver/driver.

NOTE:

The Alarm Out signal
(pin 10, capable of 25 mA sink­ing max.) is intended for logic
circuits or other low-power de­vices. If you connect a device
that draws more current than
the maximum allowed, you
could destroy the output cir­cuitry. If you wish to operate a
device that requires greater
current, then interface it with
a relay.

The LRD41C-CONNKIT consists of
with the LRD41C21/22-* 18-pin header as shown below. One 9-pin connector is
pictured at left.
below with their respective pin outs and functions when mated with the 18-pin header.

Pin 1 ----------- Aux 1 NC
Pin 2 ----------- Aux 1 OUT
Pin 3 ----------- Aux 1 NO
Pin 4 ----------- Aux 2 NC
Pin 5 ----------- Aux 2 OUT
Pin 6 ----------- Aux 2 NO
Pin 7 ----------- GND
Pin 8 ----------- GND
Pin 9 ----------- GND
Pin 10---------- Alarm Out
Pin 11 ---------- Alarm Input 7
Pin 12---------- Alarm Input 8
Pin 13---------- Alarm Input 5
Pin 14---------- Alarm Input 6
Pin 15---------- Alarm Input 3
Pin 16---------- Alarm Input 4
Pin 17---------- Alarm Input 1
Pin 18---------- Alarm Input 2

Activate an alarm with a GND;
a +5V or Open disables an
alarm.

Two 9-pin connectors, which comprise the CONNKIT, are shown

two

9-pin mating connectors that interface

2 4 6 8 10 12 14 16 18

1 3 5 7 9 11 13 15 17

18-Pin Header

ALARMS-The LRD41C21/22-* supports eight alarm inputs and
one alarm output. If multiple alarms are activated, the receiver
will sequence between the alarm presets. Up to eight presets
can be activated by alarm contacts connected to the receiver.
Any of these alarm inputs would activate an external device
through an open collector output.

AUX’S-The LRD41C21/22-* is capable of operating up to two
remotely activated auxiliary functions. Aux 3 is not available.
Aux 4’s logical output is dedicated to wiper control inside the

®

Legacy

enclosure.

REAR PANEL LRD41C-21/22-*

1 Pelco Manual C559M (5/97)

WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one (1) year after the date of shipment.
Exceptions to this warranty are as noted below:

• Two (2) years on all standard motorized and fixed focal length lenses.

• Two (2) years on Legacy
Spectra

™

, DF5 Series and DF8 Fixed Dome products.

®

, Intercept®, CM8500/CM9500/CM9750 Matrix,

• Two (2) years on WW5700 series window wiper (excluding wiper blades).

• Two (2) years on cameras.

• Six (6) months on all pan and tilts, scanners or preset lenses used in continu­ous motion applications (e.g., preset scan, tour and auto scan modes).

Pelco will warranty all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to
Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration,
normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss result­ing from the specific use or application made of the Products. Pelco’s liability for
any claim, whether based on breach of contract, negligence, infringement of any
rights of any party or product liability, relating to the Products shall not exceed the
price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable
for any special, incidental or consequential damages (including loss of use, loss of
profit and claims of third parties) however caused, whether by the negligence of
Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the
following information:

1. Model and serial number

2. Date of shipment, P .O. number , Sales Order number , or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under
the warranty conditions stated above, please include a written explanation with the
product when returned.

Ship freight prepaid to: Pelco

300 West Pontiac Way
Clovis, CA 93612-5699

Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the
factory at [phone] or [phone] to obtain an authorization number (CA
number if returned for credit, and RA number if returned for repair). Goods returned
for repair or credit should be clearly identified with the assigned CA/RA number and

®Pelco and the Pelco logo are

registered trademarks of Pelco.

©Copyright 1997, Pelco. All rights

reserved.

freight should be prepaid. All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.

Ship freight prepaid to: Pelco

300 West Pontiac Way
Clovis, CA 93612-5699

Pelco Manual C559M (5/97) 2