Pelco LL27LM User Manual

®

LL27LM

Mounting Bracket

Installation/Operation

U

®

L

LISTED

1.0 WARNINGS

Prior to installation and use of this product, the follow­ing WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Use only installation methods and materials ca­pable of supporting four times the maximum speci­fied load.

3. Only use replacement parts recommended by Pelco.

Please thoroughly familiarize yourself with the informa­tion in this manual prior to installation and operation.

2.0 DESCRIPTION

The LL27LM mounting bracket is designed to allow you
to mount an LL27 infrared illuminator to any Legacy
Series enclosure. Only one infrared illuminator can be
mounted to the enclosure/pan and tilt assembly.

C206M (6/93)

3.0 INSTALLATION

3.1 INSTALLING THE LL27LM
BRACKET

3.1.1 EH4700L/EH5700L Series

Enclosures

To install the LL27LM bracket perform the following
steps. (Refer to Figure 3.)

1. Remove enclosure from pan/tilt, if necessary.

2. Loosen the two 1/4-20 bolts (item K) from the tilt

table (item 3) on the bottom of the enclosure.

3. Remove cradle (item 4) and replace with LL27LM

mounting bracket.

The long arm of the LL27 bracket should be posi­tioned over the tilt gear side of the pan/tilt unit.

®

4. Re-attach the tile table (item 3) using the two 1/4-

20 bolts previously removed.

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827

International Customers call (1-559) 292-1981 or FAX [phone]

3.1.2 EH8106L Enclosure

Refer to Figure 4 for the following instructions.

1. Remove the two screws in the tilt table (item 1) on
the EH8106L enclosure.

2. Pry the tilt table apart from the adapter plate (item

2). The two parts are held together with silicone
sealant.

3. Clean the silicone from the mating surfaces of the
adapter plate and tilt table.

3.2 ATTACHING THE LL27 INFRARED
ILLUMINATOR

To attach the LL27 infrared illuminator to the mount­ing bracket perform the following steps.

1. Feed the stainless steel mounting straps (provided

with the LL27 illuminator) through the guide holes
of the mounting bracket as shown in Figure 2.

2. Position the LL27 under the bracket and wrap the

straps around the illuminator. T ighten the straps to
securely hold the LL27 illuminator in place.

4. Apply new silicone to the mating surfaces.

5. Insert the LL27LM mounting plate (item 3) be­tween the adapter plate and tilt table.

6. Reinstall the two screws in the tilt table.

3. Make the necessary electrical connections as de­scribed in the manual (C920M) provided with the
illuminator.

NOTE: VALUES IN PARENTHESES ARE

CENTIMETERS; ALL OTHERS ARE INCHES

Figure 1. LL27LM Dimension Drawing

Figure 2. LL27LM Mounting Bracket Installation

2 Pelco Manual C206M (6/93)

Item 3 Tilt table
Item 4 Cradle
Item K Bolt, 1/4-20 x 5/8

Phillips flat M/S SS

Figure 3. Legacy

3

®

Series Enclosure Exploded Assembly Diagram

2

1

Figure 4. Mounting Bracket Installation

Pelco Manual C206M (6/93) 3

4.0 WARRANTY AND RETURN
INFORMATION

WARRANTY
Pelco will repair or replace, without charge, any
merchandise proved defective in material or workmanship
for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers,

server, and keyboard).

• Three years on Camclosure

except the CC3701H-2, CC3701H-2X, CC3751H-2,
CC3651H-2X, MC3651H-2, and MC3651H-2X camera
models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length

lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series

matrix, and DF5/DF8 Series fixed dome products.

• Two years on Spectra

scanners, including when used in continuous motion
applications.

• Two years on Esprit

(excluding wiper blades).

• Eighteen months on DX Series digital video recorders,

NVR300 Series network video recorders, and Endura™
Series distributed network-based video products.months
on DX Series digital video recorders, NVR300 Series
network video recorders, Endura™ Series distributed
network-based video products, and TW3000 Series
twisted pair transmission products.

• One year (except video heads) on video cassette

recorders (VCRs). Video heads will be covered for a
period of six months.

• Six months on all pan and tilts, scanners or preset lenses

used in continuous motion applications (that is, preset
scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90
days from the date of Pelco shipment. All goods requiring
warranty repair shall be sent freight prepaid to Pelco,
Clovis, California. Repairs made necessary by reason of
misuse, alteration, normal wear, or accident are not
covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for
damages or loss resulting from the specific use or
application made of the Products. Pelco’s liability for any
claim, whether based on breach of contract, negligence,
infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by
the Dealer to Pelco for such Products. In no event will Pelco
be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of
third parties) however caused, whether by the negligence of
Pelco or otherwise.

The above warranty provides the Dealer with specific legal
rights. The Dealer may also have additional rights, which
are subject to variation from state to state.

®

and fixed camera models,

®

, Esprit®, ExSite™, and PS20

®

and WW5700 Series window wiper

3. Details of the defect or problem
If there is a dispute regarding the warranty of a product

which does not fall under the warranty conditions stated
above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to
the method by which the item was received by Pelco.

RETURNS
In order to expedite parts returned to the factory for repair
or credit, please call the factory at [phone] or (559)
292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly
identified with the assigned CA or RA number and freight
should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska,
Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska,
Hawaii or Puerto Rico and are instructed to return goods to
the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send
the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER,
send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

(Design and product specifications subject to

change without notice.)

If a warranty repair is required, the Dealer must contact
Pelco at [phone] or [phone] to obtain a
Repair Authorization number (RA), and provide the
following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or

Pelco invoice number

® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and

Camclosure are registered trademarks of Pelco.

™ Endura and ExSite are trademarks of Pelco.

© Copyright 1993, Pelco. All rights reserved.

4 Pelco Manual C206M (6/93)