Pelco LD4H User Manual

C3435M (8/07)
LD4H Series
Spectra

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Installation should be done only by qualified personnel and conform to all local codes.

6. Only use replacement parts recommended by Pelco.

Description

The LD4H Series of lower domes are designed for use with Spectra
bubble, and may be ordered in either clear or smoked finishes.

®

IV SE Horizon Lower Domes

®

IV SE Horizon dome systems. The lower domes feature a 6-inch (15.24 cm) acrylic dome

MODELS

LD4H-0 Smoked dome bubble

LD4H-1 Clear dome bubble

Installation

NOTE: The LD4H Series lower domes have been designed to fit with the Spectra IV SE Horizon Series dome drives only. These lower domes cannot be used

with other camera systems.

To install the lower dome:

1. Hanging down from the back box is a flexible strap (the trim ring leash). There is a large keyhole-shaped opening in the end of the trim ring leash. Slide
the large part of the keyhole opening over the raised retainer screw located on the inside edge of the lower dome. Tuck the end of the trim ring leash
behind the raised plastic stop. Before releasing the lower dome, make sure the leash will hold it securely. Refer to Figure 1.

2. After the dome drive is installed, push the lower dome inside the back box. Tighten the two captive screws to secure the lower dome. Refer to
Figure 2.

NOTE: Ensure that the lower dome is positioned to minimize the effect of the dome bubble seam on any critical viewing areas. Refer to the Important Note

shipped with the Spectra IV SE Horizon dome drive.

Figure 1. Attaching the Trim Ring Leash (Pendant Model Shown)

Figure 2. Installing the Lower Dome (Pendant Model Shown)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission
products.

• Three years on Spectra

• Three years on Genex

• Three years on Camclosure
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

• Three years on PMCL200/300/400 Series LCD monitors.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy
fixed dome products.

• Two years on Spectra III
continuous motion applications.

• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).

• Two years (except lamp and color wheel) on Digital Light Processing (DLP
The lamp and color wheel will be covered for a period of 90 days. The air filter is not
covered under warranty.

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

®

IV and Spectra IV SE Horizon products.

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

™

®

, Esprit

™

Series distributed network-based video products.

®

, ExSite

, and PS20 scanners, including when used in

®

) displays.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

REVISION HISTORY

Manual # Date Comments

C3435M 8/07 Original version.

Pelco, the Pelco logo, Camclosure, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 2007, Pelco. All rights reserved.
Endura and Spectra III are trademarks of Pelco.
DLP is a registered trademark of Texas Instruments, Inc.

Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: [phone] • Fax: [phone]

International • Tel: [phone] • Fax: [phone]