Pelco KBD960-US User Manual

Page 1
KBD960/KBR960
Desktop Intelligent
Keyboard/M
Installation/
Operation Manual
C1519M-C (8/05)
Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com
USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150
Page 2
CONTENTS
Section Page
REGULATORY NOTICES .................................................................................. 6
IMPORTANT SAFEGUARDS AND WARNINGS ............................................... 7
DESCRIPTION .................................................................................................. 8
MODELS ....................................................................................................8
READING THIS MANUAL ......................................................................... 8
KEYBOARD LAYOUT ................................................................................ 9
LCD DISPLAY....................................................................................9
ICON KEYS ....................................................................................... 9
KEYPAD............................................................................................. 9
FUNCTION KEYS .............................................................................. 9
CONTROL KEYS ..............................................................................10
LENS KEYS ......................................................................................10
JOYSTICK ........................................................................................ 10
TURBO KEY ..................................................................................... 10
ESCAPE KEY ................................................................................... 10
INSTALLATION .................................................................................................11
CONNECTING TO THE CM6800 ............................................................. 11
SETUP MODE .......................................................................................... 12
ACTIVATING SETUP MODE ............................................................12
CALIBRATING THE JOYSTICK ....................................................... 12
CREATING A SETUP PIN .................................................................13
CREATING A DEFINE PIN ............................................................... 13
ADJUSTING THE DISPLAY BRIGHTNESS ..................................... 14
CONFIGURING THE COM PORTS ................................................. 14
DEFAULT SETTINGS ............................................................... 14
CONFIGURING THE FUNCTION KEYS ..........................................15
EXITING SETUP MODE ................................................................... 15
OPERATION .....................................................................................................16
LOGGING ON ...........................................................................................16
LOGGING OFF ......................................................................................... 16
ACCESSING THE KBD960 MENUS ........................................................ 17
SENDING/RECEIVING KEYBOARD SETUPS ................................ 25
ACCESSING THE CM6800 MAIN PROGRAMMING MENU ...................26
DIAGNOSTIC MODE ................................................................................27
TESTING THE DISPLAY .................................................................. 27
TESTING THE KEYBOARD ............................................................. 27
TESTING THE SERIAL PORTS .......................................................27
TESTING THE DIP SWITCHES ....................................................... 27
SELECTING MONITORS ......................................................................... 28
MAIN MENU 1 .................................................................................. 28
MONITOR MENU ............................................................................. 28
FUNCTION KEY ............................................................................... 28
SELECTING CAMERAS ........................................................................... 28
MAIN MENU 1 .................................................................................. 28
CAMERA MENU ............................................................................... 28
FUNCTION KEY ............................................................................... 28
OPERATING PTZ CAMERAS .................................................................. 29
2 C1519M-C (8/05)
Page 3
ADVANCED OPERATION ................................................................................ 30
PRESETS ................................................................................................. 30
CREATING PRESETS......................................................................30
RECALLING PRESETS .................................................................... 30
DELETING PRESETS ...................................................................... 30
PATTERNS ............................................................................................... 31
CREATING PATTERNS .................................................................... 31
PATTERN LENGTH ..........................................................................32
STARTING PATTERNS .................................................................... 32
STOPPING PATTERNS....................................................................32
ZONES ...................................................................................................... 33
RULES TO FOLLOW WHEN CREATING ZONES ........................... 33
CREATING ZONES ..........................................................................34
PARTIAL ZONE OVERLAP .............................................................. 35
EMBEDDED ZONES ........................................................................ 36
TURNING ZONES ON AND OFF .....................................................36
ERASING ZONES ............................................................................ 36
MACROS .................................................................................................. 37
STARTING MACROS ....................................................................... 37
STOPPING MACROS.......................................................................37
PAUSING MACROS .........................................................................37
SEQUENCE .............................................................................................. 38
STARTING SEQUENCES ................................................................38
STOPPING SEQUENCES ................................................................ 38
PAUSING SEQUENCES .................................................................. 38
OPERATING RELAYS ..............................................................................39
ACTIVATING RELAYS USING F12 .................................................. 39
ACTIVATING RELAYS FROM THE GPI MENUS ............................. 39
MOMENTARY ........................................................................... 39
MULTIPLEXER CONTROL.......................................................................41
VIDEO LOSS ............................................................................................ 42
ALARMS ................................................................................................... 42
LATCHING ................................................................................ 39
RESETTING TRIGGERED ALARMS ............................................... 42
APPENDICES ...................................................................................................43
SPECIFICATIONS ............................................................................................ 47
C1519M-C (8/05) 3
Page 4
LIST OF ILLUSTRATIONS
Figure Page
1 KBD960/KBR960 ................................................................................. 9
2 Connecting to the CM6800 ................................................................ 11
3 Enter Setup PIN .................................................................................12
4 Setup Mode ....................................................................................... 12
5 Joystick Setup .................................................................................... 12
6 Advance Setup 2 ............................................................................... 13
7 LCD Brightness Setup ....................................................................... 14
8 Advance Setup 1 ............................................................................... 14
9 Key Define Mode ............................................................................... 15
10 Logon Screen .................................................................................... 16
11 Logoff Screen..................................................................................... 16
12 Main Menu 1 ...................................................................................... 17
13 Main Menu 2 ...................................................................................... 17
14 Monitor Menu .....................................................................................18
15 Camera Menu 1 ................................................................................. 18
16 Camera Menu 2 ................................................................................. 19
17 MUX Menu 1 ......................................................................................19
18 MUX Menu 2 ......................................................................................20
19 Alarm Menu ....................................................................................... 20
20 GPI Menu 1 ........................................................................................ 21
21 GPI Menu 2 ........................................................................................ 21
22 Preset Menu ...................................................................................... 22
23 Macro Menu .......................................................................................22
24 Sequence Menu ................................................................................. 23
25 Define Menu 1 ................................................................................... 23
26 Define Menu 2 ................................................................................... 23
27 Define Preset Menu ........................................................................... 24
28 Define Zone Menu ............................................................................. 24
29 Setup LCD Menu ............................................................................... 24
30 Programming Menu ........................................................................... 24
31 Database Menu ................................................................................. 25
32 Password Screen ............................................................................... 26
33 Main Programming Menu .................................................................. 26
34 Diagnostic Mode Menu ...................................................................... 27
35 LCD Test ............................................................................................ 27
36 Keyboard Test ....................................................................................27
37 SIO Test ............................................................................................. 28
38 DIP Switch Test .................................................................................. 28
39 Pattern Definitions ............................................................................. 32
40 Basic Zone Creation .......................................................................... 35
41 Partial Zone Overlap ..........................................................................36
42 Embedded Zones .............................................................................. 37
43 MUX Control Menu ............................................................................ 42
4 C1519M-C (8/05)
Page 5
LIST OF TABLES
Table Page
A Function Key Defaults .......................................................................... 15
B Main Menu 1 ........................................................................................ 17
C Main Menu 2 ........................................................................................17
D Monitor Menu ....................................................................................... 18
E Camera Menu 1 ................................................................................... 18
F Camera Menu 2 ................................................................................... 19
G MUX Menu 1 ........................................................................................ 19
H MUX Menu 2 ........................................................................................ 20
I Alarm Menu.......................................................................................... 20
J GPI Menu 1 ..........................................................................................21
K GPI Menu 2 .......................................................................................... 21
L Preset Menu ........................................................................................22
M Macro Menu .........................................................................................22
N Sequence Menu ...................................................................................23
O Define Menu 1 ..................................................................................... 23
Q Define Preset Menu ............................................................................. 24
R D efine Zone Menu .............................................................................. 24
S Setup LCD Menu ................................................................................. 24
U Database Menu ................................................................................... 25
V Spectra/Esprit Programming Menu ...................................................... 33
W Relay Unit 1 ......................................................................................... 41
X Relay Unit 2 ......................................................................................... 41
Y Triggered Alarm Functions ...................................................................43
LIST OF APPENDICES
Appendix Page
A Icons Legend ....................................................................................... 44
B Setup Mode Menu Tree (DIP Switch 2 ON) .........................................45
C Diagnostic Mode Menu Tree (DIP Switch 1 ON)..................................46
D Operation Mode Menu Tree (DIP Switch 2 OFF) ................................. 47
C1519M-C (8/05) 5
Page 6
REGULATORY NOTICES
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particu­lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn­ing the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
6 C1519M-C (8/05)
Page 7
IMPORTANT SAFEGUARDS AND WARNINGS
1. Read, keep, and follow these instructions.
2. Heed all warnings.
3. There are no user-serviceable parts inside this unit. Only authorized service personnel may open the unit.
4. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
5. WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture if this unit is designed for indoor use only.
6. Unless this unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain or moisture.
7. Do not expose this unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on this unit.
8. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
9. The installation method and materials should be capable of supporting four times the weight of the unit and equipment.
10. Do not install near any heat source.
11. Only use attachments/accessories specified by the manufacturer.
12. Clean only with dry cloth.
13. Do not defeat the safety purpose of the polarized or grounding-type plug.
14. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the unit.
15. Unplug this unit during lightning storms or when unused for long periods of time.
16. A CCC-approved power cord must be used to power this equipment when used in China.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are im­portant operating and maintenance in­structions in the literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
FOR QUALIFIED SERVICE PERSONNEL ONLY
1. Only use replacement parts recommended by Pelco.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
2. After replacement/repair of this unit’s electrical components, conduct a resis­tance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.
C1519M-C (8/05) 7
Page 8
DESCRIPTION
The KBD960/KBR960 Keyboard includes Pelco’s proprietary M protocol, allowing it to be used with all M devices, such as Pelco’s latest matrix switch – the CM6800. You can program the keyboard, and you can create and execute macros. You have access to effective monitoring procedures for any CCTV application.
You can assign simple or complex functions to many of the keys. This allows you to configure the keyboard to suit a specific monitoring environment. Some of the keyboard features include the following:
User-friendly, icon-driven design
Select and monitor any connected camera or video input
Control pan and tilt functions for cameras and configured receivers
Control camera iris (zoom and focus) for configured equipment
Control camera auxiliary functions for configured equipment
Control peripheral devices, such as video printers, frame stores, and video multiplexers
Select macros to execute complex procedures
Store and recall camera presets for equipment with preset capabilities
Download function key configurations to and from other keyboards
MODELS
KBD960 Programmable keyboard that can be used with all M devices.
KBD960-X Same as the KBD960, except 230 VAC, 50 Hz
KBR960 Same functions as the KBD960 models, except it can be
KBR960-X Same as the KBR960, except 230 VAC, 50 Hz
READING THIS MANUAL
Each icon key corresponds to an icon on the LCD display. Each icon represents a function.
You will be instructed to “Select [icon]” when reading this manual. Press the icon key that corresponds to the icon on the LCD.
The functions of the KBR960 and KBR960-X are the same as the KBD960 and KBD960-X. The only difference is that the KBR960 models can be mounted onto a rack. Any reference in this manual to the KBD960 also applies to the KBR960 models.
You will read references to the CM6800. However, the M protocol allows this key­board to be used with other M devices.
120 VAC, 60 Hz
mounted onto a rack. 120 VAC, 60 Hz
8 C1519M-C (8/05)
Page 9
Y
KEYBOARD LAYOUT
The KBD960 keyboard consists of the following:
1. LCD Display
2. Icon Keys
3. Keypad
4. Function Keys
5. Control Keys
6. Lens Keys
7. Joystick
8. Turbo Key
9. Escape Key
FUNCTION KEYS
4
(F1-F24)
2
ESCAPE KEY
9
ICON KEYS
3
KEYPAD
LCD DISPLAY
1
CONTROL KEYS
5
7
6
JOYSTICK
TURBO KE
8
LENS KEYS
00891
Figure 1. KBD960/KBR960
LCD DISPLAY
The LCD is a four-line display. Each line displays different information.
Line 1 Displays the video output (which is typically a monitor) and the video
input source (which is typically a camera).
Line 2 Displays the last number entered and the icon of the current menu.
Line 3 Displays alarm messages and other prompts.
Line 4 Displays the icons for the icon keys.
ICON KEYS
These eight blue keys correspond to the icons directly above on the LCD display. These icons change depending on the mode you are in.
KEYPAD
The keyboard has a standard numeric keypad with two additional keys for select­ing cameras and monitors.
FUNCTION KEYS
The 24 function keys (F1-F24) can be programmed according to your application and the type of CCTV installation.
Refer to the The supplied blank labels and punched LEXAN® decal overlay should be used.
Installation
section for an explanation on how to program these keys.
C1519M-C (8/05) 9
Page 10
CONTROL KEYS
These keys are used for the following functions:
Step backward through available camera selections.
Step forward through available camera selections.
Select and execute macros.
Rcl: Recall previous selections.
Alt: Reserved for future use.
Prst: Recall preset.
Lock: Reserved for future use.
LENS KEYS
You can use these keys to control cameras equipped with motorized zoom lenses and motorized pan and tilt units. These keys are sometimes used to acti­vate other functions. For example, the Open/Close key is also used when creat­ing preset labels.
Zoom in/out.
Focus near/far.
Open/close the iris.
JOYSTICK
The proportional joystick allows variable speed control. It gives you full control over the pan and tilt movements, from minimum to maximum speed. You should calibrate the joystick before setting up anything else.
TURBO KEY
Pressing this key while moving the joystick switches pan motors into high-speed mode on equipment that is capable of panning.
ESCAPE KEY
This key exits you from the mode you are in.
10 C1519M-C (8/05)
Page 11
INSTALLATION
:
The following items are supplied:
KBD960/KBR960 Keyboard
CM9505UPS Universal Power Supply
Two 25 ft (7.6 m) straight RJ-45 cables (one with ferrite)
10 blank labels and 10 punched LEXAN decal overlays
CONNECTING TO THE CM6800
NOTE:
Communication to the keyboards is RS-485. Pelco recom­mends using four-conductor, shielded, 18-gauge twisted pairs, such as Belden 9418, or a similar cable that meets or exceeds the basic require­ments for EIA RS-485 applications.
VOLUME
COM 1
RESET BUTTON
1. Set all DIP switches OFF. The DIP switches are located on the bottom of the
2. Connect the RJ-45 straight cable with ferrite from COM 1 of the keyboard to
3. Connect the other RJ-45 straight cable from the power supply to COM 3 of
4. Plug the power supply into a 120 VAC power source.
8
DIP SWITCHES
RS-485 SERIAL PORT
16
3231
43
876
VIDEO OUTPUTS
keyboard.
the CM9505UPS power supply. The ferrite end of the cable must go into the keyboard. See Figure 2.
the CM6800.
MAIN PORT USED FOR POWER INTO KEYBOARD, AND FOR COMMUNICATION LINK TO PELCO 6800. THESE I/O LINES ARE CONNECTED TO 8-PIN RJ SOCKET JP1 AS SHOWN BELOW. INCOMING DC IS ALSO BROUGHT IN VIA THIS COM PORT.
JP1 PIN FUNCTION JP1 PIN FUNCTION
1 RS-485 Tx+ 5 GND (0 VDC IN)
2 RS-485 Tx- 6
00893
COM
1
5
2
6
3
7
4
8
3 7 RS-485 Rx-
4 +12 VDC IN 8 RS-485 R+
ALARM
123456 78
CONTROL
PTZ
AT+T-R+R-T+T-R+R-B
OUT
1
2
COM 1
F 3
120/230~ 50/60 HZ
25 WATTS
COM 3 DEFAULT SETTINGS M, RS-485, 19200 BAUD, NO PARITY, 1 STOP BIT
8 DATA BITS,
STRAIGHT CABLE
CM6800 COM 3
RJ-45 PIN-OUTS
1 Rx+ 2 Rx­3 NC 4 NC 5 GROUND 6 NC 7 Tx­8 Tx+
KBD960
RJ-45 PIN-OUTS
1 Tx+ 2 Tx­3 4 5 6 7 Rx­8 Rx+
(SUPPLIED)
RS-485
CM9505UPS UNIVERSAL POWER SUPPLY
STRAIGHT CABLE WITH FERRITE (SUPPLIED)
KBD960
Figure 2. Connecting to the CM6800
C1519M-C (8/05) 11
Page 12
ENTER SETUP PIN
SETUP MODE
You can configure the KBD960 in the Setup Mode. You can do the following:
Create a Personal Identification Number (PIN) for entering the Setup Mode.
Create a PIN that provides access to features on the Define Menu.
Calibrate the joystick.
Adjust the display brightness.
Set the data transmission speeds for the keyboard’s three COM ports.
Define the function keys.
Select a host port.
The default setup PIN is 1234. You can change it in the Setup Mode.
ACTIVATING SETUP MODE
1. Set DIP Switch 2 ON. “ENTER SETUP PIN” appears.
2. Enter your PIN number (the default number is 1234) and “SETUP MODE”
appears.
Figure 3. Enter Setup PIN
SETUP MODE vX.XX
JSTK
ADVLCD
Figure 4. Setup Mode
JOYSTICK SETUP
xxx
xxx
(xxx, xxx)
xxx
xxx
Figure 5. Joystick Setup
00895
00896
CALIBRATING THE JOYSTICK
1. Select
2. Select with the joystick in the center default position.
00897
3. Move the joystick completely to the left and select .
4. Move the joystick completely to the right and select .
5. Move the joystick completely down and select .
6. Move the joystick completely up and select .
7. Select to save the joystick configuration.
JSTK
from Setup Mode. “JOYSTICK SETUP” appears on the LCD.
8. Select to return to the Setup Menu.
RESTORING FACTORY DEFAULT SETTINGS
1. Set DIP switches 1, 2, and 8 ON and recycle power.
2. Re-calibrate the joystick if using a keyboard version before 1.20.
For version 1.20 and later keyboards, the joystick is automatically calibrated during a factory default initialization.
12 C1519M-C (8/05)
Page 13
Setup Pin! **** Confirm! **** Define Pin! **** Confirm! ****
Advance Setup 2
DEF
NUM
Figure 6. Advance Setup 2
CREATING A SETUP PIN
The factory settings for the KBD960 include the default setup PIN 1234. Follow these steps to change the default PIN:
ADV
00898
1. Select
2. Select
3. Select and/or to choose Setup PIN.
from Setup Mode.
and/or to locate Advance Setup 2.
4. Select
DEF
, enter a four-digit PIN, and select
NUM
5. Advance the cursor to the confirm row, select
DEF
select
once again. The menu indicates “OK” if confirmed.
NUM
DEF
once again.
NUM
DEF
, re-enter your PIN, and
NUM
6. Select to save your PIN.
CREATING A DEFINE PIN
You also need a PIN to access the extended keyboard functions that are avail­able in the Define Menu. The default define PIN is also 1234. Follow these steps to change it (refer to Figure 6):
select
ADV
from Setup Mode.
DEF
, enter a four-digit PIN, and select
NUM
DEF
once again. The menu indicates “OK” if confirmed.
NUM
NUM
DEF
NUM
DEF
once again.
, re-enter your PIN, and
1. Select
2. Select and/or to locate Advance Setup 2.
3. Select and/or to choose Define PIN.
4. Select
5. Advance the cursor to the confirm row, select
6. Select to save your PIN.
C1519M-C (8/05) 13
Page 14
LCD BRIGHTNESS SETUP
ADJUSTING THE DISPLAY BRIGHTNESS
1. Select
LCD
from Setup Mode.
Figure 7. LCD Brightness Setup
Advance Setup 1
COM1!!! None (Host) COM2!!! None COM3!!! None Local Address!! 1
Figure 8. Advance Setup 1
00900
00899
2. Select to make the display brighter or to make the display dimmer.
3. Select and then .
You can also adjust the display brightness by selecting
Refer to the
Operation
section of this manual.
LCD
from the Define Menu.
CONFIGURING THE COM PORTS
1. Select
2. Select and/or to navigate to the COM 1 row.
3. Select and/or to assign a baud rate.
4. Select to set parity for the communications port.
5. Select to set the Host.
6. Select and/or to navigate to the Local Address row.
ADV
from Setup Mode and scroll to the Advance Setup 1 screen.
NOTE:
COM 2 is functional, but only COM 1 is optimized for the protocol. COM 3 is not used for normal operation.
NOTE:
Pelco recommends that you reserve addresses 1-8 for the KBD960/KBR960 keyboards. In System 6800, you should not use an address higher than 8.
7. Select and/or to assign an address.
8. Select to save your configuration and then select to return to
the Setup Mode.
Default Settings
COM 1 – 19200 baud, No Parity, Set as HOST
Address – 1
14 C1519M-C (8/05)
Page 15
CONFIGURING THE FUNCTION KEYS
NOT DEFINED NUMx ESC BKSPACE ENTER DEFINE
KEY DEFINE
PLEASE ENTER A KEY
DEF NUM
00901
Figure 9. Key Define Mode
NOTE:
Refer to Table A for the factory default settings.
NOTE:
Many of the functions do not require that you enter a define number. In those cases, skip steps 5 and 6.
NOTE:
In the GPI Menu, F1-F8 are associated with the external relays in the current GPI.
1. Select from Setup Mode to switch to the key define mode.
2. Press a function key you want to configure. If the key is already defined, its assigned function is shown. If not, “Def = NOT DEFINED” appears on the LCD screen.
3. Select and/or to scroll through the list of available functions.
4. Select to choose a function.
5. Select
6. Select
DEF
and enter the define number.
NUM
DEF
.
NUM
7. Select and then .
Table A. Function Key Defaults
Function Key Default Function
F1 Camera Auxiliary 1
F2 Camera Auxiliary 2
F3 Camera Auxiliary 3
F4 Camera Auxiliary 4
F5 Camera Auxiliary 5
F6 Camera Auxiliary 6
F7 Camera Auxiliary 7
F8 Camera Auxiliary 8
F9 Camera Pattern 1
F10 Camera Pattern 2
F11 Camera Pattern 3
F12 External Relay 1
F13 Multiplexer
F14 Alarm Menu
F15 Macro Menu
F16 Sequence Menu
F17 GPI Menu
F18 Define Menu
F19 Menu Forward
F20 Menu Backward
F21 Backspace
F22 Enter
F23 Clear
F24
EXITING SETUP MODE
1. Select .
2. Set DIP switch 2 OFF.
C1519M-C (8/05) 15
Page 16
OPERATION
LOGGING ON
This section describes the operation of a CM6800 System using the KBD960 keyboard. Before you begin operating the KBD960, make sure you have com­pleted the following:
1. Connections have been made and initial power-up has been completed.
2. CM6800 setup files have been programmed.
3. PINs have been set up to allow logging on, access to the setup functions, and access to the Define Menu.
You must also have the following information:
The logical camera number list, complete with identification names
The logical monitor number list, complete with identification names
A list of all macros
A list of all peripheral devices connected
A list of alarms connected to the system
A list of presets for each relevant camera
KEYBOARD 960 vX.XX
Enter Monitor
Figure 10. Logon Screen
1 1
Logoff?
YES
NO
Figure 11. Logoff Screen
1. Set all DIP switches OFF.
2. Enter the monitor number and press .
00902
LOGGING OFF
1. Select .
2. Select
00903
3. Select
The keyboard goes offline for a short while before returning to the “KEYBOARD 960” display.
LOG
FF
O
YES
.
.
16 C1519M-C (8/05)
Page 17
ACCESSING THE KBD960 MENUS
1. Set DIP switch 2 OFF.
2. Enter the number of the monitor and then press .
3. Press and the Main Menu 1 icons appear.
Table B. Main Menu 1
1 1
PRSTGPIMUX
Figure 12. Main Menu 1
LOG O
MAIN MENU 1
Select to bring up the Monitor Menu. If you enter a number before selecting this icon, the monitor number changes to that number.
FF
00904
Select to bring up the Camera Menu. If you enter a number be­fore selecting this icon, the camera number changes and the camera switches on the current monitor without going into the Camera Menu.
Select to bring up the MUX Menu. You can enter a number be-
MUX
fore selecting this icon. If you enter a number before selecting this icon, the multiplexer number changes and the system switches to that multiplexer without going into the MUX Menu.
When an alarm is triggered, this icon appears on the keyboard screen. The current alarm shown on the user monitor is the alarm that appears when the Alarm Menu is selected.
Select to bring up the GPI Menu. If you enter a GPI number be-
GPI
fore selecting this icon, control and data information are re­quested for the selected GPI.
Select to bring up the Preset Menu. If you enter a number before
PRST
selecting this icon, the preset is called without the Preset Menu being displayed.
Select to bring up the next page (Main Menu 2).
LOG
FF
O
Select to log off the system.
Table C. Main Menu 2
1 1
MAC
SEQ
DEF
Figure 13. Main Menu 2
Select to bring up the Macro Menu. If you enter a macro number
MAC
before selecting this icon, the selected macro plays without hav­ing to go into the Macro Menu.
00905
SEQ
Select to bring up the Sequence Menu. If you enter a sequence number before selecting this icon, the selected sequence plays without going into the Sequence Menu.
Select to bring up Define Menu 1. You will see
Enter your define PIN. You will not have to re-enter your define
DEF
PIN unless the keyboard goes offline or you log off. When you
enter your PIN, Define Menu 2 appears. You will also see
in Define Menu 2. You can adjust the display brightness in De-
fine Menu 1 or Define Menu 2.
or Selecting either one returns you to Main Menu 1.
MAIN MENU 2
PIN
and
LCD
LCD
.
C1519M-C (8/05) 17
Page 18
Table D. Monitor Menu
1 1
Figure 14. Monitor Menu
1 1
2
1
Figure 15. Camera Menu 1
MONITOR MENU
Select to request the previous logical monitor number in the sys­tem and to grant control of the monitor if it is available. The logi­cal monitor number range is 1-9999.
00906
Select to request the next logical monitor number in the system and to grant control of the monitor if it is available. The logical monitor number range is 1-9999.
This icon indicates whether or not you have control of the monitor. A highlighted icon means you have control. Select this icon to re­quest or release control of the selected monitor. If you enter a number before selecting this icon, the keyboard requests control of that monitor.
Reserved for future use.
Select this icon to return to Main Menu 1.
Table E. Camera Menu 1
CAMERA MENU 1
Select to request the previous logical camera number in the system and grant control if it is available.
00907
Select to request the next logical camera number in the system and grant control if it is available.
Select to run a selected pattern.
This icon shows whether or not you have control of the selected camera. A highlighted icon means you have control. Select this icon to request or release control of the selected camera. If you enter a number before selecting this icon, the keyboard requests control of that camera.
1
2
Select to send an AUX 1 set command to the selected camera. When you release the key, a clear command is sent.
Select to send an AUX 2 set command to the selected camera. When you release the key, a clear command is sent.
Select to bring up Camera Menu 2.
Select to return to Main Menu 1.
18 C1519M-C (8/05)
Page 19
Table F. Camera Menu 2
1
3
5
4
1
7
6
8
Figure 16. Camera Menu 2
1 1
MUX
MUX
Figure 17. MUX Menu 1
CAMERA MENU 2
Select to send an AUX 3 set command to the selected camera. When you release the key, a clear command is sent.
3
00908
Select to send an AUX 4 set command to the selected camera.
4
When you release the key, a clear command is sent.
Select to send an AUX 5 set command to the selected camera.
5
When you release the key, a clear command is sent.
Select to send an AUX 6 set command to the selected camera.
6
When you release the key, a clear command is sent.
Select to send an AUX 7 set command to the selected camera.
7
When you release the key, a clear command is sent.
Select to send an AUX 8 set command to the selected camera.
8
When you release the key, a clear command is sent.
or Select to return to Camera Menu 1.
Table G. MUX Menu 1
MUX MENU 1
Select to request the previous logical multiplexer number in the system and grant control of the multiplexer if it is available.
00909
MUX
Select to request the next logical multiplexer number in the sys­tem and grant control of the multiplexer if it is available.
This icon shows whether or not you have control of the se­lected multiplexer. A highlighted icon means you have control. Select this icon to either request or release control of the se­lected multiplexer. If you enter a number before selecting this icon, the keyboard requests control of that multiplexer.
Select to send a MUX TAPE command to the selected multi­plexer.
Select to send a MUX LIVE command to the selected multi­plexer.
Select to send a MUX ZOOM command to the selected multi­plexer. If you enter a number before selecting this icon, the command sent to the multiplexer becomes a MUX SWITCH CHANNEL command to the specified channel.
Select to bring up MUX Menu 2.
Select to return to Main Menu 1.
C1519M-C (8/05) 19
Page 20
Table H. MUX Menu 2
1 1
MUX
Figure 18. MUX Menu 2
1 1
Figure 19. Alarm Menu
MUX MENU 2
Select to send a MUX PIP command to the selected multiplexer.
00910
Select to send a MUX 4-camera command to the selected multiplexer.
Select to send a MUX 9-camera command to the selected multiplexer.
Select to send a MUX 16-camera command to the selected multi­plexer.
Select to bring up MUX Menu 1.
Select to return to Main Menu 1.
Table I. Alarm Menu
ALARM MENU
Select to request the previous triggered logical alarm number in the system. The CM6800 matrix interprets this command as a Previous Alarm Step.
00911
Select to request the next triggered logical alarm number in the system. The CM6800 matrix interprets this command as a Next Alarm Step.
Select to turn off the alarm siren of the keyboard.
Select to send an ALARM RESET command for the currently displayed alarm.
Select to send an ALARM RESET ALL command. The CM6800 matrix interprets this command as a Reset Current Alarm on all monitors.
Select to pause an alarm that has been triggered.
Select to return to Main Menu 1.
20 C1519M-C (8/05)
Page 21
Table J. GPI Menu 1
1 1
GPI
GPI
MTRY
1 2 3 4
Figure 20. GPI Menu 1
GPI MENU 1
Select to set the current GPI to the input value. Select to re-
GPI
00912
quest control of the selected GPI and send a message to gather information about the status of the auxiliaries within the GPI. You have control if this icon is highlighted.
If this icon is highlighted, the auxiliary control method is momen­tary. If it is not highlighted, the auxiliary control method is latching. In momentary mode, selecting the icon sends an AUX ON com­mand and releasing the key sends an AUX OFF command. The latching mode disables the AUX OFF command from being sent when the key is released. In latching mode, you can specify a
MTRY
number up to 6553 and then press the auxiliary number to set the auxiliary and have it unlatch at the specified time (1-6553 in sec­onds). If you do not enter a number, the auxiliary latches until an AUX OFF command is sent. You can issue an AUX OFF com­mand by placing the keyboard in MTRY (momentary) mode again and pressing the key (when the key is released an AUX OFF is sent and the AUX ON when pressing the key is ignored).
Select to send a set auxiliary command for the auxiliary within
1
the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
Select to send a set auxiliary command for the auxiliary within
2
the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
Select to send a set auxiliary command for the auxiliary within
3
the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
Select to send a set auxiliary command for the auxiliary within
4
the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
1 1
GPI
5 6 7 8
Figure 21. GPI Menu 2
Select to bring up GPI Menu 2.
Select to return to Main Menu 1.
Table K. GPI Menu 2
GPI MENU 2
Select to send a set auxiliary command for the auxiliary within
5
00913
6
7
8
the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode
Select to send a set auxiliary command for the auxiliary within the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
Select to send a set auxiliary command for the auxiliary within the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
Select to send a set auxiliary command for the auxiliary within the selected GPI. Pressing the key sends an AUX ON and releasing it sends an AUX OFF in momentary mode.
Select to return to GPI Menu 1.
Select to return to Main Menu 1.
C1519M-C (8/05) 21
Page 22
Table L. Preset Menu
1 1
PRST
PRST
Figure 22. Preset Menu
1 1
MAC
MAC
Figure 23. Macro Menu
PRESET MENU
PRST
Select to send a PRESET CALL command to the current camera.
Select to send a PATTERN START command to the current
00914
camera. You can enter a number to initiate a specific pattern.
Select to send a ZONE SCAN ON command to the current camera and display the “Zone On” text. When this text is displayed, you can select this icon again to send a ZONE SCAN OFF command, which displays the “Zone Off” text.
Select to return to Main Menu 1.
Table M. Macro Menu
MACRO MENU
Select to request the previous logical macro number in the system and grant control of the macro if it is available.
00915
MAC
Select to request the next logical macro number in the system and grant control of the macro if it is available.
This icon shows whether or not the user has control of the selected macro. If the icon is highlighted, you have control. Select this icon to either request or release control of the selected macro. If you enter a number before selecting this icon, the keyboard requests control of that macro.
Select to start or stop a macro.
Select to start or stop a macro.
Select to send a stop command to the selected macro.
Select to send a MACRO PAUSE command to the selected macro.
Select to return to Main Menu 1.
22 C1519M-C (8/05)
Page 23
Table N. Sequence Menu
1 1
SEQ
SEQ
Figure 24. Sequence Menu
SEQUENCE MENU
Select to request the previous logical sequence number in the system and grant control of the sequence if it is available.
Select to request the next logical sequence number in the
00916
system and grant control of the sequence if it is available.
This icon shows whether or not you have control of the selected sequence. If the sequence is highlighted, you have control.
SEQ
Select this icon to request or release control of the selected sequence. If you enter a number before selecting this icon, the keyboard will request control of that sequence number.
Select to send a SEQ PLAY BWD command to the selected sequence.
Select to send a SEQ PLAY FWD command to the selected sequence.
Reserved for future use.
Reserved for future use.
Select to return to Main Menu 1.
Table O. Define Menu 1
1 1
PIN
LCD
PIN
Figure 25. Define Menu 1
1 1
DEF
PRST
LCD
MENU
Figure 26. Define Menu 2
DEFINE MENU 1
Enter your PIN to bring up Define Menu 2. Define Menu 2
PIN
00917
LCD
appears automatically if you have already entered your PIN. You will not have to re-enter your PIN unless the keyboard goes offline or you log off.
Select to adjust the LCD display brightness.
Table P. Define Menu 2
DEFINE MENU 2
PRST
00918
LCD
MENU
Select to enter the Define Preset Menu.
Select to enter the Define Zone Menu.
Select to enter the Setup LCD Menu.
Select to send a start pattern programming command to the current camera. A highlighted pattern symbol appears. Selecting pattern again stops the command and the pattern symbol be­comes normal.
Select to bring up the Programming Menu.
Select to bring up the Database Menu.
Select to return to Main Menu 1.
C1519M-C (8/05) 23
Page 24
Table Q. Define Preset Menu
1 1
DEF
PRST
DEL
PRST
Figure 27. Define Preset Menu
1 1
DEF
Figure 28. Define Zone Menu
1 1
LCD
Figure 29. Setup LCD Menu
DEFINE PRESET MENU
Select to send a set preset command and a preset label to the
PRST
current camera. A preset number is required prior to selecting this icon.
00919
DEL
Reserved for future use.
Select to return to the Define Menu.
Table R. D efine Zone Menu
DEFINE ZONE MENU
Select to send a set zone command to the current camera.
00920
Select to return to the Define Menu.
Table S. Setup LCD Menu
SETUP LCD MENU
Select to make the display brighter.
00921
Select to make the display dimmer.
Select to save your settings.
1 1
DEF
MENU
PGM
Figure 30. Programming Menu
Select to return to the Define Menu.
Table T. Programming Menu
PROGRAMMING MENU
Select to send a MENU ITEM DOWN command to the system master.
00922
PGM
Select to send a MENU ITEM UP command to the system master.
Select to send a MENU ITEM LEFT command to the system master.
Select to send a MENU ITEM RIGHT command to the system master.
Select to increase the current item.
Select to decrease the current item. Enter a number and select this icon to set the editing field.
Select to display the program menu on your monitor.
Select to return to the Define Menu.
24 C1519M-C (8/05)
Page 25
DEF
00923
Figure 31. Database Menu
NOTE:
COM 3 is RS-232 and is only used for sending/receiving settings between keyboards. It is not used for normal operation.
NOTE:
To send/receive setup information, all KBD960 keyboards must be connected to the M bus. However, each keyboard must have a unique local M device address.
Table U. Database Menu
DATABASE MENU
Select to send the keyboard’s key configuration to another keyboard. You must enter the local device address of the second keyboard. This is only sent to a device on the same bus as the keyboard.
Select to receive another keyboard’s key configuration database. You must enter the local device address of the second keyboard. This is only sent to a device on the same bus as the keyboard.
Select to return to the Define Menu.
SENDING/RECEIVING KEYBOARD SETUPS
You can set up only one KBD960 keyboard and send the information to another keyboard. You can also receive the setup information from a connected key­board.
The COM ports are located on the bottom of the keyboard.
Follow these steps to send or receive setup information between keyboards:
1. Select from Define Menu 2 to bring up the Database Menu. See Figure 31.
2. Select to send setup information to a connected keyboard.
“Sending Data” appears on the LCD. “Key Data Sent” appears on the LCD when the transfer is complete.
or
Select to receive setup information from a connected keyboard.
“Receiving KeyDefs” appears on the LCD. “Keys Uploaded” appears on the LCD when the transfer is complete.
C1519M-C (8/05) 25
Page 26
ACCESSING THE CM6800 MAIN PROGRAMMING MENU
1. Select
DEF
.
2. Enter your Define PIN.
3. Select
4. Select
MENU
.
PGM
. The following screen appears on your monitor.
PELCO VIDEO SWITCHER
MODEL CM6800
PASSWORD TO MAIN MENU
SCRATCHPAD SEQUENCE
*******
RETURN
00619
Figure 32. Password Screen
5. Enter your password (default is 2899100). The Main Programming Menu appears.
! PELCO SWITCHER ! MODEL CM6800 ! MAIN MENU
! 1! CAMERA ! 2! LOGICAL CAMERA ! 3! MONITOR ! 4! ACCESS ! 5! TIME & DATE ! 6! PORT ! 7! PRIORITY ! 8! SEQUENCE ! 9! MACRO ! 10! ALARM CONTACTS ! 11! EVENT TIMER ! 12! SET AUXILIARY MENU ! 13! SET PASSWORD ! 14! ABOUT CM6800
! ENGLISH
! RETURN
00924
Figure 33. Main Programming Menu
Refer to the CM6800 Installation/Operation Manual (C1515M) for detailed in­structions on setting the various items on the Main Programming Menu.
26 C1519M-C (8/05)
Page 27
DIAGNOSTIC MODE
DIAGNOSTIC MODE vX.XX
Figure 34. Diagnostic Mode Menu
LCD TEST
G2
G1
G0
T0
Figure 35. LCD Test
To activate the Diagnostic Mode set DIP switch 1 ON. This mode allows the fol­lowing tests:
LCD test
Keyboard test
00925
Serial Input/Output (SIO) test
DIP Switch test
TESTING THE DISPLAY
1. Select while in the Diagnostic Mode.
2. Select
00926
3. Select
4. Select
G0
to test graphic page 0.
G1
to test graphic page 1.
G2
to test graphic page 2.
KEYBOARD TEST vX.XX
PLEASE ENTER A KEY
Joystick Position – (xxx, xxx)
00927
Figure 36. Keyboard Test
NOTE:
Version 1.20 and later displays three joystick positions (xxx, xxx, xxx).
5. Select
T0
to test the text page.
6. Select .
TESTING THE KEYBOARD
NOTE: If the software running on the KBD960 is v1.20 or later, then DIP switch 3 is used to indicate whether or not the software is taking A-to-D readings from the zoom axis of the joystick. If DIP switch 3 is OFF, you should see three readings (xxx, xxx, xxx) on the keyboard test screen. If the zoom A-to-D reading (the third reading) changes as you move the zoom top, DIP switch 3 should be OFF. If the zoom A-to-D reading does not change as you move the zoom top, DIP switch 3 should be ON.
1. Select .
2. Press each key to ensure that the display shows the correct key.
3. Select .
C1519M-C (8/05) 27
Page 28
SIO TEST
COM2
COM1
COM3
Figure 37. SIO Test
DIPSWITCH TEST
00000001
Figure 38. DIP Switch Test
TESTING THE SERIAL PORTS
This test is reserved for factory use only.
00928
TESTING THE DIP SWITCHES
1. Select .
2. Beginning with switch 2, set each switch ON while observing the display.
00929
28 C1519M-C (8/05)
Page 29
SELECTING MONITORS
You can select up to eight monitors. There are several ways you can select monitors.
MAIN MENU 1
1. Enter the monitor number (1-8).
2. Press or select .
The monitor number appears next to on the keyboard LCD.
MONITOR MENU
1. Select from Main Menu 1.
2. Cycle through the available monitors using and/or .
You can also enter a monitor number and press or select .
NOTE:
F22 is the “enter” default, but you can assign this function to one of the other function keys.
SELECTING CAMERAS
NOTE:
you can assign this function to one of the other function keys.
F22 is the “enter” default, but
FUNCTION KEY
Follow these steps to select a monitor using F22:
1. Press .
2. Enter a monitor number.
3. Press F22.
There are also several ways you can select cameras.
MAIN MENU 1
1. Enter a logical camera number (1-9999).
2. Press or select . The camera number appears next to
on the keyboard LCD.
CAMERA MENU
1. Select from Main Menu 1.
2. Cycle through the available cameras using and/or .
You can also enter a camera number and press or select .
FUNCTION KEY
Follow these steps to select a camera using F22:
1. Press .
2. Enter a camera number.
3. Press F22.
You can also use and to cycle through cameras.
C1519M-C (8/05) 29
Page 30
OPERATING PTZ CAMERAS
The controls for PTZ cameras are located on the right-hand side of the keyboard.
The proportional joystick allows variable speed drives. It gives you full control over the pan and tilt movements, from minimum to maximum speed. Speed is proportional to the amount by which you move the joystick from its center location.
Press
The joystick only provides directional control when a fixed speed PTZ camera is installed.
The various functions of a PTZ camera can be controlled as follows:
1. To zoom in or out, use .
2. To focus near or far, use .
3. To open or close the iris, use .
while moving the joystick to enable high speed operation.
30 C1519M-C (8/05)
Page 31
ADVANCED OPERATION
PRESETS
NOTE:
Presets are only possible when receivers or pan/tilt units have preset capability.
NOTE:
You are asked for your PIN only when you access the Define Menu for the first time after logon.
A preset camera position is a set of parameters which define pan, tilt, zoom, and focus adjustments. There are four ways you can recall a preset camera position:
Manually using the keyboard
Automatically as the result of an alarm condition
From a macro command
From a sequence command
CREATING PRESETS
There are 64 available presets. For example, follow these steps to create Preset 1:
1. Move the joystick to the desired position.
2. Select
3. Select
4. Enter 1 and select
5. Press to scroll through the alphanumeric characters. Each preset
6. Move the joystick to SET and then to the right.
DEF
from Main Menu 2. Refer to Table C.
PRST
to bring up the Preset Menu.
PRST
. “PROGRAMMING PRESET 01 ENTER PRESET
LABEL” appears on the monitor.
label can have up to 20 characters. Move the joystick to the right to set each character.
RECALLING PRESETS
Follow these steps to recall the preset you created:
1. Go to Main Menu 1.
2. Enter 1.
3. Select
PRST
or press . The camera moves to the preset position
and the preset label appears on the monitor.
DELETING PRESETS
Follow these steps to delete the preset you created above:
1. Select
2. Enter 1 and select
3. Move the joystick down to DELETE and then to the right.
DEF
from Main Menu 2.
PRST
. “PROGRAMMING PRESET 01 ENTER PRESET
LABEL” appears on the monitor.
C1519M-C (8/05) 31
Page 32
PATTERNS
A pattern is a user-defined, viewable camera path with a definite beginning and end. You must create a pattern before the time-out clock expires. For example,‚ the timer is 60 seconds. If you are using a Spectra II®‚ the timer is 1.5, 3, or 6 minutes. (See the section on
Pattern Length
.) You will not see the time-out clock
on the monitor.
CREATING PATTERNS
1. Move the joystick to a desired starting point.
DEF
2. Select
from Main Menu 2. Refer to Table C.
NOTE:
Your pattern can be the same
length as the time-out clock or less.
3. Select
. The icon becomes highlighted and “PROGRAMMING PAT-
TERN” appears on the monitor.
4. Move the joystick to a desired end point before time-out.
5. Select again to save the pattern. The icon returns to normal.
Figure 39 shows a viewing area within which pattern definition can take place. The line segment shows one of many paths along which a pattern definition can be created.
PRESSING THE BUTTON AT POINT D OR AT ANY INTERMEDIATE POINT ENDS PATTERN DEFINITION
JOYSTICK TO POINT A, PRESS THE BUTTON TO START PATTERN DEFINITION
B
A
VIEWABLE AREA
C
D
MONITOR
CAMERA
JOYSTICK CONTROL
00930
Figure 39. Pattern Definitions
32 C1519M-C (8/05)
Page 33
PATTERN LENGTH
You can set three time values for single pattern lengths and three corresponding time values for two half-pattern lengths from the Esprit™ Programming Menu. The single pattern lengths are 1.5 minutes, 3 minutes, and 6 minutes. The corresponding half­pattern lengths are .75 minutes, 1.5 minutes, and 3 minutes.
Follow these steps to bring up the programming menu:
1. Go to Define Menu 2. Refer to Table C.
NOTE:
If the Esprit programming menu shows no choices for pattern creation, then you have early models and are limited to creating and running patterns based on the time values of 60 seconds for full and 30 seconds for half-patterns. Intercept
®
equipment also uses 60 seconds for a full pattern and 30 seconds for half-patterns.
2. Enter 95 and press the Prst side of
The monitor displays the Preset Label Menu. The Programming Menu appears when you click Set.
3. Perform the steps in Table V.
.
Table V. Esprit Programming Menu
Esprit Programming Menu
1. Move the joystick to position the cursor beside Other.
2. Press the Open side of to enter the submenu.
3. Position the cursor beside Pattern Length.
4. Press the Open side of .
5. Scroll through the available pattern lengths (1.5, 3, or 6). For two half­patterns of .75 minutes each, select 1.5; for two half patterns of 1.5 min­utes each, select 3; and for two half patterns of 3 minutes each, select 6.
6. Press the Open side of to make your time selection.
7. Exit the menu.
STARTING PATTERNS
1. Select
2. Select . “RUNNING PATTERN” appears on the monitor. The pattern
PRST
from Main Menu 1.
runs from start to finish, returns to its start position, and begins again.
STOPPING PATTERNS
Move the joystick to stop a running pattern.
C1519M-C (8/05) 33
Page 34
ZONES
A zone is a user-defined space to which a label is attached and a camera is associated. The camera used at the time the zone boundaries are defined is associated with the zone. The zone label appears on the selected monitor after zone definition if you move the camera within the defined zone. You can define and associate up to eight zones with the same camera. A priority level (1-8, with 8 being the highest) is assigned to each zone.
RULES TO FOLLOW WHEN CREATING ZONES
You must remember these points before you create a zone:
Always move the joystick so that camera movement is from left to right. Refer to Figure 40.
If you create eight equally spaced zones for a single camera, it would in­clude an entire circle and each zone would cover an angular distance of about 45 degrees (if camera/receiver configuration and site geometry allow).
Name each defined zone so that each zone priority can be easily identified.
Plan physical placement and associated priority levels ahead of time if you anticipate creating many zones for a camera.
You must assign a priority level (1-8) before you create a zone. Priority levels
are hierarchical and are only relevant when multiple zones are being created.
34 C1519M-C (8/05)
Page 35
NOTE:
To create zones when using Spectra III cameras, you must enable the zone label display in the Spectra III menus.
CREATING ZONES
1. Move the joystick to Point A.
2. Select
3. Select .
4. Enter a zone priority level (1-8) and select again. The icon becomes
5. Press to scroll through the alphanumeric characters.
6. Move the joystick to SET and then to the right. The zone label appears on
7. Move the joystick to Point B. You should move the joystick from left to right
8. Enter the priority level again and select . The icon returns to normal.
Repeat these steps if you want to create additional zones.
If you move the associated camera through the area defined by the zone (approaching the zone edges from either direction), the zone label appears on the selected monitor as you enter the zone and disappears as you exit the zone. Refer to Figure 40.
DEF
from Main Menu 2 and enter your PIN, if necessary.
highlighted signaling the start of zone creation. “Edit label. Ack-set for left edge. Pan right. Press 81 & F5 for right edge.” appears on the monitor.
Each zone label can have up to 20 characters. Move the joystick to the right to advance to the next character.
the monitor.
only.
00931
Figure 40. Basic Zone Creation
C1519M-C (8/05) 35
Page 36
PARTIAL ZONE OVERLAP
Partial zone overlap occurs when the end of one zone overlaps with the begin­ning of another zone. The zone with the highest priority level appears at all times. Refer to Figure 41.
ZONE A BEGINS
THIS PORTION OF ZONE B DOES NOT APPEAR BECAUSE ZONE A OVERLAPS IT AND HAS A HIGHER PRIORITY LEVEL. THE REMAINDER OF ZONE B DOES APPEAR.
Figure 41. Partial Zone Overlap
ZONE B BEGINS
ZONE A
PRIORITY 5
ZONE A ENDS
ZONE B
PRIORITY 2
ZONE B ENDS
00932
36 C1519M-C (8/05)
Page 37
EMBEDDED ZONES
An embedded zone is a zone that is between two other zones. In Figure 42, Zone C is embedded between Zone A and Zone B.
An embedded zone is not seen unless its priority level is higher than the priority level of the other zones. Since Zone C has a priority level of 6, portions of Zone A and Zone B are not seen.
ZONE A BEGINS
ZONE C BEGINS
ZONE B BEGINS
ZONE A
PRIORITY 5
ZONE A ZONE C
ZONE A ENDS
ZONE C ENDS
ZONE B ENDS
ZONE C
PRIORITY 6
ZONE B
PRIORITY 2
ZONE B
RESULT
00933
Figure 42. Embedded Zones
TURNING ZONES ON AND OFF
Follow these steps to turn zones on and off:
1. Select
PRST
from Main Menu 1 to bring up the Preset Menu.
2. Select . “ZONES OFF” or “ZONES ON” appears.
3. Select again to either turn the zones off or on.
ERASING ZONES
NOTE: DO NOT
pan left or right
1. Select
while erasing zones.
2. Select .
3. Enter the priority level of a zone you want to erase and select again.
4. Move the joystick down and select SET. The zone is erased.
Repeat these steps to erase other zones. You can also use these steps to start over should you make a mistake during zone creation.
C1519M-C (8/05) 37
DEF
from Main Menu 2.
Page 38
MACROS
A macro is a sequence of commands or steps. When you run a macro, the steps programmed into that macro are performed. Macros can be run manually or automatically. Automatic operation can be the result of alarms or the reaching of specific times and dates.
If you want to start a macro, make sure no other keyboard has control of the PTZ on the monitor that you want the macro to start on.
When a macro completes all its steps, it stops and only runs again if restarted. A continuous macro runs until you clear it or stop it.
To set up a macro, you must bring up the CM6800 Programming Main Menu from the KBD960 or use the CM6800-MGR Program Manager.
STARTING MACROS
There are two ways you can start a macro. For example, follow these steps to start macro number 1:
1. Go to Main Menu 2.
or
MAC
MAC
.
.
2. Select
3. Select or to scroll to macro number 1.
4. Select or to start the macro.
1. Go to Main Menu 2.
2. Enter 1.
3. Select
STOPPING MACROS
There are two ways you can stop a macro. Follow these steps to stop macro number 1:
1. Go to Main Menu 2.
2. Enter 1.
or
MAC
.
3. Select
1. Go to the Macro Menu.
2. Select or to scroll to macro number 1.
3. Select either , , or .
PAUSING MACROS
Follow these steps to pause macro number 1:
1. Go to Main Menu 2.
2. Select
3. Select or to scroll to macro number 1.
4. Select to pause the macro.
5. Select again to restart the macro.
38 C1519M-C (8/05)
MAC
.
Page 39
SEQUENCE
You can select up to 16 sequences. Camera number and title, sequence status, and time/date appear on the monitor when you select a sequence.
To set up a sequence, you must bring up the CM6800 Programming Main Menu from the KBD960 or use the CM6800-MGR Program Manager.
There can be 72 steps in a sequence. A sequence can consist of various com­mands (patterns, presets, random scan, frame scan, stop scan) and auxiliaries (global auxiliary on/off or camera auxiliary on/off).
STARTING SEQUENCES
You can start a sequence from Main Menu 2 or from the Sequence Menu:
1. Go to Main Menu 2.
2. Enter a sequence number (1-16).
or
SEQ
.
3. Select
1. Go to the Sequence Menu.
2. Select or to scroll through available sequences.
3. Select or .
STOPPING SEQUENCES
There are two ways to start a sequence:
1. Go to the Sequence Menu.
2. Select or to scroll to the sequence number.
3. Select .
or
Enter a camera number.
PAUSING SEQUENCES
1. Go to Main Menu 2.
2. Select
3. Select or to scroll to the sequence number.
SEQ
.
4. Select to pause the sequence.
5. Select again to restart the sequence.
C1519M-C (8/05) 39
Page 40
OPERATING RELAYS
NOTE:
You will hear a brief click from the relay unit whenever you activate a momentary or latching relay contact.
To operate relays from a KBD960 keyboard, you must know which GPI to call and which auxiliary (AUX) to select on the keyboard.
You can cascade two relay units. Each relay unit has eight GPIs. Relay Unit 1 has a GPI range of 1-8, and Relay Unit 2 has a GPI range of 9-16. Refer to Tables W and X.
There are two ways you can operate relays from the KBD960.
ACTIVATING RELAYS USING F12
Follow these steps to activate a momentary relay:
1. Go to Main Menu 1.
2. Enter a logical relay contact number (1-128).
3. Press F12.
A momentary relay does not remain on. Only a latched relay remains on. If you want a latched relay, you must activate it from the GPI menus.
ACTIVATING RELAYS FROM THE GPI MENUS
You can activate relays from the GPI menus as momentary or latching. A momen­tary relay goes on briefly and then turns off. A latched relay remains on until you turn it off.
Momentary
To activate relay contact 4, for example, follow these steps:
1. Go to Main Menu 1 and enter 1 (GPI). GPI 1 is associated with relay contact 4. Refer to Table C.
2. Select
GPI
to bring up GPI Menu 1. This menu displays auxiliaries 1-4.
Make sure
MTRY
is highlighted. When
MTRY
is highlighted, any relay you
activate will be momentary.
3. Select
.
4
Latching
To activate the same relay as latching, follow these steps:
1. Go to Main Menu 1 and enter 1 (GPI).
2. Select
3. Select
4. Select
5. Select
GPI
to bring up GPI Menu 1.
MTRY
so that it is not highlighted. When
any relay you activate latches (remains on).
. This icon becomes highlighted.
4
MTRY
and then the highlighted auxiliary icon to turn off the latched
relay.
MTRY
is not highlighted,
40 C1519M-C (8/05)
Page 41
NOTE:
In Relay Unit 2, GPIs 9-16 are associated with the physical relays (1-64) on the back of the unit. However, GPIs 9-16 are also associated with logical relays 65-128. For example, the physical relays for GPI 9 are 1-8 and the logical relays are 65-72.
Table W. Relay Unit 1
GPI RELAY CONTACTS
112345678 2 9 10 11 12 13 14 15 16 3 17 18192021222324 4 25 26272829303132 5 33 34353637383940 6 41 42434445464748 7 49 50515253545556 8 57 58596061626364
ASSOCIATED AUX 1 2 3 4 5 6 7 8
Table X. Relay Unit 2
GPI RELAY CONTACTS
9 65 66676869707172 10 73 74 75 76 77 78 79 80 11 81 82 83 84 85 86 87 88 12 89 90 91 92 93 94 95 96 13 97 98 99 100 101 102 103 104 14 105 106 107 108 109 110 111 112 15 113 114 115 116 117 118 119 120 16 121 122 123 124 125 126 127 128
ASSOCIATED AUX 1 2 3 4 5 6 7 8
An REL2064 relay unit set for GPI 1 overlaps with the internal relays on the CM6800. Auxiliary commands sent to external relays 1-3 also operate the inter­nal relays on the CM6800. You can set the relay range of the REL2064 higher if you want to avoid overlapping the external relays with internal relays 1-3.
If you press F12 on the keyboard, auxiliary commands are sent to the CM6800 and operate the internal relays of the CM6800, as well as external relays.
Auxiliary commands sent from the GPI Menu go directly to the REL2064 to control the external relays only. However, if an REL2064 relay unit is not set for GPI 1, auxiliary commands sent from the GPI menu operate the CM6800 relays.
C1519M-C (8/05) 41
Page 42
MULTIPLEXER CONTROL
You can also control multiplexers with the KBD960 keyboard. You can connect multiplexers to any input.
Refer to the CM6800 Installation/Operation Manual (C1515M) for instructions on setting the multiplexers for keyboard control.
Follow these steps to control multiplexers:
1 1
PRSTGPIMUX
Figure 43. MUX Control Menu
NOTE:
does not work on a
9-channel multiplexer.
LOG O
1. Enter a MUX input number and press
. Each MUX input is associated
with a camera input. Figure 43 shows MUX 1 being controlled.
FF
00934
2. Select
MUX
. MUX Menu 1 appears.
means you have MUX control.
MUX
should be highlighted, which
3. Cycle through the 16 picture inserts (if you have a 16-channel multiplexer)
by entering the camera number and selecting .
4. Select again to zoom into the MUX camera. You can move the joy-
stick to view a specific area.
5. Select to bring up MUX Menu 2. The icons for a picture-in-picture display,
4-camera display, 9-camera display, and 16-camera display appear.
6. Select to view four of the available 16 cameras on one monitor.
You can cycle through all 16 cameras, four at a time, by repeatedly selecting
.
7. Select to view nine of the available 16 cameras on one monitor.
Select again to see the remaining seven cameras.
8. Select to view all 16 available cameras on one monitor.
42 C1519M-C (8/05)
Page 43
VIDEO LOSS
The loss of a video signal may alert you or trigger an alarm. The alarm is reported back to the keyboard. Using the video loss function, faulty cameras can be dis­abled if necessary.
ALARMS
Alarms can be armed or disarmed from the KBD960 keyboard using the System 6800 menus.
RESETTING TRIGGERED ALARMS
A triggered alarm causes a continuous tone. The alarm volume can be altered using the level control on the bottom of the keyboard.
You cannot turn on an alarm that has been muted. It stays muted until all alarms on the current monitor are cleared or the user switches monitors. This alerts all operators who have access to the alarm.
Flashing with number This means the specific alarm number has
Table Y. Triggered Alarm Functions
been triggered.
Select this icon to mute the triggered alarm.
Select to reset the triggered alarm.
Select to reset all triggered alarms. This does not reset all alarms in the CM6800.
Select this icon to pause a triggered alarm.
C1519M-C (8/05) 43
Page 44
APPENDICES
LOG
LOG
FF
O
OFF
LOG OFF
YES
YES
LOG OFF
NO
NO
SETUP/DEFINE
PIN
PIN
SAVE SELECTION
DEL
DELETE
MORE MENU
EXIT
CAMERA SELECTION
MONITOR SELECTION
SCROLL UP SCROLL FIELD UP
SCROLL DOWN SCROLL FIELD DOWN
PLAY FWD SCROLL RIGHT
PLAY BWD SCROLL LEFT
SCROLL OPTION UP
SCROLL OPTION DOWN
KEYBOARD SELECT
KEYBOARD KEY TEST
JOYSTICK
JSTK
ADJUST
ADVANCE
ADV
MENUS
SERIAL PORT TEST
SEND KEYBOARD SETUP
RECEIVE KEYBOARD SETUP
TEST GRAPHIC
G0
PAGE 0
TEST GRAPHIC
G1
PAGE 1
TEST GRAPHIC
G2
PAGE 2
TEST TEXT
T0
PAGE 0
PARITY
DIP SWITCH TEST
DISPLAY
LCD
BRIGHTNESS
COM1
COM PORT 1
COM2
COM PORT 2
COM3
COM PORT 3
AUX 1, RELAY 1
AUX 1, RELAY 1
1
AUX 2, RELAY 2
2
AUX 3, RELAY 3
3
4
5
6
7
8
GPI
MTRY
MAC
MUX
AUX 4, RELAY 4
AUX 5, RELAY 5
AUX 6, RELAY 6
AUX 7, RELAY 7
AUX 8, RELAY 8
RESET ALARM
RESET ALL ALARMS
MUTE
ALARM
GPI MENU
RELAY MOMENTARY
MACRO SELECT
DEVICE PAUSE
STOP
MUX MENU
TAPE MUX
ZOOM MUX
PIC IN PIC MUX
4-CAMERA MUX
9-CAMERA MUX
16-CAMERA MUX
LIVE MUX
MUX CAMERA CONTROL
SEQUENCE
SEQ
MENU
CAMERA
PRST
PRESET
PATTERN
ZONE
DEFINE
DEF
MENU
PROGRAM
PGM
MENU
DEFINE
DEF NUM
NUMBER
MENU
MENU
Appendix A. Icons Legend
44 C1519M-C (8/05)
Page 45
ENTER SETUP PIN
SETUP MODE vX.XX
NOT DEFINED NUMx ESC BKSPACE ENTER DEFINE
ADVLCD
Advance Setup 1
COM1!!! None (Host) COM2!!! None COM3!!! None Local Address!! 1
KEY DEFINE
PLEASE ENTER A KEY
DEF
NUM
JSTK
JOYSTICK SETUP
xxx
xxx
(xxx, xxx)
xxx
xxx
Setup Pin! **** Confirm! **** Define Pin! **** Confirm! ****
NUM
DEF
LCD BRIGHTNESS SETUP
Appendix B. Setup Mode Menu Tree (DIP Switch 2 ON)
Advance Setup 2
00936
C1519M-C (8/05) 45
Page 46
DIAGNOSTIC MODE vX.XX
G1
G0
DIAGNOSTIC MODE vX.XX
PLEASE ENTER A KEY
Joystick Position – (xxx, xxx)
LCD TEST
G2
T0
KEYBOARD TEST vX.XX
DIAGNOSTIC MODE vX.XX
COM2
COM1
DIAGNOSTIC MODE vX.XX
SIO TEST
COM3
DIPSWITCH TEST
00000001
00937
Appendix C. Diagnostic Mode Menu Tree (DIP Switch 1 ON)
46 C1519M-C (8/05)
Page 47
MAIN MENU 1
1 1
CAMERA MENU 1
1 1
CAMERA MENU 2
1
5
3
MONITOR MENU
1 1
6
4
LOGOFF MENU
1 1
Logoff?
PRSTGPIMUX
LOG O
FF
YES
NO
PRESET MENU
1 1
PRST
PRST
GPI MENU 1
1 1
GPI
GPI
MTRY
1 2 3 4
GPI MENU 2
2
1
1
7
8
1 1
GPI
5 6 7 8
ALARM MENU
1 1
1 1
MAC
MACRO MENU
1 1
MAC
SEQUENCE MENU
1 1
SEQ
DEFINE MENU 1
1 1
PIN
LCD
PIN
SEQ
MAC
SEQ
MAIN MENU 2
DEF
DEFINE MENU 2
MUX MENU 1
1 1
MUX
MUX
1 1
DEF
PRST
LCD
MENU
MUX MENU 2
1 1
MUX
DEFINE PRESET MENU
1 1
DEF
PRST
PRST DEL
DEFINE ZONE MENU
1 1
DEF
SETUP LCD MENU
1 1
LCD
PROGRAMMING MENU
1 1
DEF
MENU
PGM
DATABASE MENU
DEF
Appendix D. Operation Mode Menu Tree (DIP Switch 2 OFF)
00938
C1519M-C (8/05) 47
Page 48
SPECIFICATIONS
ELECTRICAL
Input Voltage: 12 VDC from 120 or 230 VAC, 50/60 Hz
Power Consumption: 400 mA
Communications: RS-485
Operating Distance: To 3,900 ft (1.2 km) on 24-gauge (0.5 mm) wire for direct
Connectors: Two 8-pin, RJ-45 connectors (female); RS-485 serial ports
OPERATIONAL
Joystick: Proportional
Display: Four-line, backlit LCD for programming and control
LCD Menu Display: Eight icon keys for LCD menu selection
control operation
One 4-pin, RJ-45 connector (female); RS-232 serial (diag­nostic) port
Two 6-pin RJ-45 connectors (female) not used
Numerical Input: Ten-key numeric keypad with two additional keys for camera
Function Keys: Twenty-four function keys
Control Keys: Six keys for control of various functions
Lens Keys: Three keys for zoom, iris, and focus control
GENERAL
Operating Temperature: 32° to 120°F (0° to 49°C)
Dimensions KBD960: 15.5 (W) x 3.3 (H) x 7.8 (D) inches
KBR960: 6.96 (W) x 1.27 (H) x 19.00 (D) inches
Shipping Weight: 4.59 lb (2.08 kg)
and monitor selection
(39.45 x 8.38 x 19.81 cm)
(17.68 x 3.23 x 48.26 cm)
(Design and product specifications subject to change without notice.)
48 C1519M-C (8/05)
Page 49
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products and the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X.
• Three years on all other fixed camera models (including Camclosure® Inte­grated Camera Systems) and Genex® Series (multiplexers, server, and key­board).
• Two years on all standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9700 Series Matrix, DF5 and DF8 Series Fixed Dome products.
• Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous motion applications.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders and NVR300 Series network video recorders.months on DX Series digital video recorders, NVR300 Series network video recorders, and all Endura™ Series distributed network­based video products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty. Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise. The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)289­9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice num­ber
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco. RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge. Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA Phone: 650-737-1700 Fax: 650-737-0933
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual # Date Comments
C1519M 6/01 Original version. C1519M-A 5/02 Added
C1519M-B 1/03 Revised C1519M-C 8/05 Revised manual per ECO #04-10657. Revised first note on page 12. Removed last note on page 12 and revised the
® Pelco, the Pelco logo, Spectra, Spectra II, Genex, Legacy, Esprit, Camclosure, and Intercept are registered trademarks of Pelco. © Copyright 2005, Pelco. ® Lexan is a registered trademark of General Electric Company. All rights reserved.
Models
section. Added ferrite information to
Installation
section. Added Step 5 to
default function for F9-F11 per ECO #01-7510. Revised Table M. Added
Sequence
Calibrating the Joystick
sections. Updated
Regulatory Notices
Calibrating the Joystick
section. Added two notes on page 27.
section per ECO #02-8581 and ECO #02-8394.
.
Deleting Presets
Configuring the COM Ports
section. Revised
Macros
and
. Revised
Page 50
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East
Loading...