Pelco KBD4002 User Manual

LIVE/VCR

ITO

NIT M

AIN S

POT

CLEARCAM

EQ VIE

PAN / TILT

TTE

AUX

RES

ON O

KBD4002

MADE IN USA.

WIDE

FAR

KBD4002

Genex® Multiplexer

Keyboard

Installation/

Operation Manual

C581M-B (1/04)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120

2 Pelco Manual C581M-B (1/04)

CONTENTS

Section Page

IMPORTANT SAFEGUARDS AND WARNINGS................................................................ 4

REGULATORY NOTICES .................................................................................................. 4

DESCRIPTION ................................................................................................................... 5

INSTALLATION ..................................................................................................................6

MULTIPLEXER MODE INSTALLATION.....................................................................6

MULTIPLEXER SERVER MODE INSTALLATION ..................................................... 7

OPERATION ......................................................................................................................8

PROGRAMMING .............................................................................................................. 19

PASSWORD ............................................................................................................. 20

MENUS ..................................................................................................................... 20

SYSTEM SETUP (VIEW KEY) .......................................................................... 20

ADVANCED SYSTEM SETUP (VIEW KEY) .....................................................22

RECORD SETUP (LIVE/VCR KEY) .................................................................. 24

CUSTOM VCR SETUP (LIVE/VCR KEY) .........................................................26

CAMERA SETUP (NUMBER AND CAM KEYS) ...............................................27

ACTIVITY DETECTION MASK SETUP ............................................................29

SEQUENCE SETUP (SEQ KEY) ...................................................................... 30

HELP MENU ..................................................................................................... 31

MULTIPLE CAMERA DISPLAY SETUP .................................................................... 32

PROGRAMMING THE PICTURE-IN-PICTURE DISPLAY ( KEY) ............ 32

PROGRAMMING THE 4-CAMERA DISPLAY ( KEY) ................................ 32

PROGRAMMING THE 9-CAMERA DISPLAY ( KEY) ................................ 33

PROGRAMMING THE 16-CAMERA DISPLAY ( KEY) .............................. 33

PROGRAMMING MENU DEFAULTS ....................................................................... 34

PROGRAMMING A PRESET ....................................................................................35

PROGRAMMING A PATTERN ..................................................................................35

TROUBLESHOOTING ...................................................................................................... 36

SPECIFICATIONS............................................................................................................. 37

WARRANTY AND RETURN INFORMATION .................................................................... 39

LIST OF ILLUSTRATIONS

Figure Page

1 Switch Locations and RJ-45 Jack Pinouts ......................................................... 7

2 KBD4002 Keyboard Definitions ......................................................................... 9

3 Basic System Setup Menu ................................................................................20

4 Advanced System Setup Menu ......................................................................... 22

5 Basic VCR Setting Menu .................................................................................. 25

6 Custom VCR Setup Menu ................................................................................. 26

7 Basic Camera Menu ......................................................................................... 27

8 Activity Detection Mask .....................................................................................29

9 Camera Sequence Menu .................................................................................. 30

10 Help Menu ......................................................................................................... 30

LIST OF TABLES

Table Page

A Keyboard Addresses ..........................................................................................7

B Operation Guide ................................................................................................ 11

C Camera Numbers with Switch 7 ON ................................................................. 19

D VCR Types ........................................................................................................25

E Programming Menu Defaults ............................................................................34

Pelco Manual C581M-B (1/04) 3

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

REGULATORY NOTICES

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or =television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

4 Pelco Manual C581M-B (1/04)

DESCRIPTION

The KBD4002 Genex® Multiplexer Keyboard is a full-function keyboard controller for the Genex MX4000 Multiplexer and the Genex MX4000SVR Multiplexer Server.

This manual covers the KBD4002 keyboard’s operation with the duplex and simplex models of the multiplexer. The differences, as they pertain to the keyboard, will be indicated in the text and art wherever necessary.

There are two modes of operation - multiplexer mode and multiplexer server mode–depending on whether the keyboard is connected to a multiplexer or to a server.

In the multiplexer mode, a single keyboard interfaces up to 16 multiplexers that are daisy-chained together. With 9-channel multiplexers, the keyboard can control up to 144 cameras; with 16-channel multiplexers, up to 256 cameras can be controlled.

In the multiplexer server mode, up to four keyboards can be connected to a server, which interfaces up to eight multiplexers. Up to 72 cameras can be controlled with 9-channel multiplexers or 128 cameras with 16-channel multiplexers.

In addition to performing all the control functions that can be done from the front panel of the multiplexer, the keyboard features additional keys for full control of fixed speed and variable speed pan, tilt, and lens functions. Variable speed control is accomplished with the number keypad using the “select-a-speed” feature. With select-a-speed, each digit (1-9) represents a relative pan and tilt speed. The number 1 represents the slowest speed available while the number 9 speed equates to turbo pan (for those receivers capable of supporting turbo pan speed). When the number 9 is entered, the tilt will operate at the number 8 speed. Entering the number 0 sets a mid-range speed. The keyboard can also operate presets, auxiliaries, and patterns and can be used to program the multiplexer or server.

Pelco Manual C581M-B (1/04) 5

INSTALLATION

NOTE:

The KBD4002 keyboard in combination with a Genex multiplexer provides Coaxitron

control of pan, tilt, and lens functions.

When used with 15-bit standard Coaxitron receivers, such as the CX9000 Series, the PT7700, and the ED25/27/28/29, the KBD4002 in conjunction with the multiplexer supports all pan, tilt, and lens functions, and AUX on/off. The keyboard will not set or call presets or support preset scanning.

When used with 32-bit extended Coaxitron receivers, such as Esprit

, Intercept®, Spectra®, and LRD41C21/LRD41C22 Series, the KBD4002 in conjunction with the multiplexer will support all the functions of a 15-bit receiver, including the setting and calling of presets and patterns. It will not support programming of labels for presets or patterns. If labels for presets or patterns are required, they would need to be programmed with a different control, such as the MPT9500.

The following parts are supplied:

1 KBD4002 keyboard 1 25-foot (7.6 m) data cable

There are two modes of operation–multiplexer mode and multiplexer server mode–depending on whether the keyboard is connected to a multiplexer or to a server.

In the multiplexer mode, a single keyboard is plugged into the back of a Genex MX4000 Multiplexer.

In the multiplexer server mode, up to four keyboards can be connected to the back of a Genex MX4000SVR Multiplexer Server. A KBDKIT(-X) is required for each keyboard connected to the remote keyboard port.

Proceed to the

Multiplexer Mode Installation or Multiplexer Server Mode Installation

MULTIPLEXER MODE INSTALLATION

1. Remove the DIP switch cover plate from the rear of the keyboard (refer to Figure 1).

2. Set the switches (refer to Figure 1 for switch locations).

ADDRESS

Set switches 1, 2, and 3 OFF. This is address 0, which selects the multiplexer mode of operation.

COMMUNICATION MODE

Set switch 4 OFF to enable the polled communication mode. Use this for normal keyboard operation.

Set switch 4 ON to put the keyboard in the non-polled communication mode. Use this when the keyboard communicates remotely over communications media that will not support the polled mode. This is any communications media that introduces a significant delay in the transmission of data (for example, phone line transmission systems). In the non-polled mode, the keyboard can be used to control multiplexer(s) only. The non-polled mode is not supported by the multiplexer server.

UNUSED

Leave switch 5 OFF. It is not used.

TURBO MODE

Set switch 6 ON to enable the turbo pan feature. Set the switch OFF to disable the turbo pan feature.

section.

CAMERA ADDRESS MODE

There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (refer to Table C) or by addressing the cameras in groups of 16 according to the multiplexer they are connected to. For example, multiplexer 1, cameras 1-16; multiplexer 2, cameras 1-16, etc.

Set switch 7 ON if you want to address all cameras consecutively.

Set switch 7 OFF if you want to address cameras according to the multiplexer they are connected to.

PROGRAMMING MODE

Set switch 8 ON to program the multiplexer and camera presets and patterns from the keyboard. Set the switch OFF to disable programming.

6 Pelco Manual C581M-B (1/04)

3. Replace the cover on the back of the keyboard.

12345678

NOTE:

For distances over

25 feet (7.6 m), you

must

order the KBDKIT(-X) Remote Keyboard Wiring Kit. Refer to the KBDKIT(-X) manual for installation procedures.

MULTIPLEXER SERVER MODE INSTALLATION

NOTE:

If the keyboard will be connected to a server that will operate in the paired mode configuration, only addresses 1 and 3 can be used. Refer to the server manual for information about the paired mode configuration.

4. A 25-foot (7.6 m) data cable with RJ-45 connectors is supplied with the keyboard. Plug one end of the cable into the back of the keyboard and plug the other end into the COM IN connector on the back of the multiplexer.

The keyboard receives power from the multiplexer. The LED display will light momentarily when the keyboard receives power. The LED will stay on when you enter a multiplexer address.

5. Peel off the protective covering over the LED display in the upper left corner of the keyboard.

1. Remove the DIP switch cover plate from the rear of the keyboard (refer to Figure 1).

2. Set the switches (refer to Figure 1 for switch locations).

ADDRESS

Refer to Table A to set the address of the keyboard.

Table A. Keyboard Addresses

Keyboard Switch Settings

Address 1 2 3

1ONOFF OFF

2 OFF ON OFF

3ONONOFF

4 OFF OFF ON

UNUSED

Switches 4 and 5 are not used in the multiplexer server mode. They must be placed in the OFF position.

TURBO MODE

Set switch 6 ON to enable the turbo pan feature. Set the switch OFF to disable the turbo pan feature.

CAMERA ADDRESS MODE

There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (refer to Table C) or by addressing the cameras in groups of 16 according to the multiplexer they are connected to; for example, multiplexer 1, cameras 1-16; multiplexer 2, cameras 1-16, etc.

PIN 1

12345678

RJ-45

JACK PINOUTS

1 TX+ 5 GND 2 TX– 6 3 12 VAC/DC 7 RX–

}

4 NONPOLAR 8 RX+

Figure 1. Switch Locations and RJ-45 Jack Pinouts

Pelco Manual C581M-B (1/04) 7

Set switch 7 ON if you want to address all cameras consecutively.

Set switch 7 OFF if you want to address cameras according to the multiplexer they are connected to.

PROGRAMMING MODE

Set switch 8 ON to program the server and the multiplexer. Set the switch OFF to disable programming.

3. Replace the cover on the back of the keyboard.

4. Connect the keyboard to the MX4000SVR Multiplexer Server. A maximum of four keyboards can be connected to the server. One keyboard can be connected to the LOCAL KEYBOARD port on the server, and up to three keyboards can be connected to the REMOTE KEYBOARD(S) port on the server. Or four keyboards can be connected to the remote.

LOCAL KEYBOARD PORT

To connect the keyboard to the LOCAL KEYBOARD port, a 25-foot (7.6 m) data cable with RJ-45 connectors is supplied with the keyboard. Plug one end of the cable into the back of the keyboard and plug the other end into the LOCAL KEYBOARD port on the server. Refer to the multiplexer server manual for instructions.

The keyboard receives power from the multiplexer. The LED display will light when the keyboard receives power. The display will show the address of the multiplexer with which the keyboard is communicating.

REMOTE KEYBOARD(S) PORT

To connect a keyboard(s) to the REMOTE KEYBOARD(S) port on the server you must order a KBDKIT(-X) for each keyboard. Follow the instructions that are supplied with the kit. Refer to Figure 1 for the keyboard RJ-45 pin-outs.

OPERATION

The keyboard receives power from the transformer. The LED display will light when the keyboard receives power. The display will show the address of the multiplexer with which the keyboard is communicating.

5. Peel off the protective covering over the LED display in the upper left corner of the keyboard.

IMPORTANT NOTE ABOUT PROGRAMMING

When the keyboard is plugged into a multiplexer or multiplexer server, the keyboard is ready to operate. However, some minimal programming may be required to

make your system work.

MULTIPLEXER

The default settings for the duplex and simplex multiplexers are not the same, and it should not be assumed that there is nothing more to do after connecting the keyboard to the system. Below are the minimum things to check.

1. To allow the keyboard to communicate with multiplexers in the polled mode (switch 4 OFF), you must designate one multiplexer (any one) as the master and all the others as slaves. If you have just one multiplexer, it must be the master. In the non-polled communication mode (switch 4 ON), all multiplexers must be slaves (the keyboard is the master).

Set the master/slave designation from the front panel of the multiplexer, not from the keyboard. Go to the Advanced System Setup menu

(refer to multiplexer manual) and select master or slave in the COMM. TYPE menu item. The default is SLAVE for duplex multiplexers and MASTER (KBD T/D) for simplex multiplexers.

8 Pelco Manual C581M-B (1/04)

2. If you have more than one multiplexer, each one must have its own address (Unit ID in the Advanced System Setup menu). If you have a server, the multiplexer address must match the input on the server to which it is connected; for example, if the multiplexer is connected to input 3 on the server, set the multiplexer address to 3. Set the

address from the front panel of the multiplexer, not from the keyboard.

3. If you have moveable cameras (they must be Coaxitron compatible), you must program the Coaxitron format for each camera (Camera menu). The duplex multiplexer COAXITRON FORMAT default setting is OFF, while the simplex default setting is EXTENDED. Programming can be done from the front panel of the multiplexer or from the keyboard (refer to the

MULTIPLEXER SERVER

Below is the minimum you should check.

If you intend to control two monitors from one keyboard (paired mode), you must change the settings for the monitors (Monitor menu). Programming the server can only be done from the keyboard. Refer to the server manual for instructions.

Programming

section for keyboard instructions).

IMPORTANT NOTE ABOUT COAXITRON CONTROL OF CAMERAS

The KBD4002 keyboard provides Coaxitron control of pan, tilt, and lens functions.

The duplex multiplexer COAXITRON FORMAT (refer to the default setting is OFF and must be changed in order to use Coaxitron control. The simplex multiplexer default setting is EXTENDED and 32-bit Coaxitron control can be used without changing the setting.

When used with 15-bit standard Coaxitron receivers, such as the CX9000 Series, the PT7700, and the ED25/27/28/29, the KBD4002 supports all pan, tilt, and lens functions, and AUX on/off. The keyboard will not set or call presets or support preset scanning.

When used with 32-bit extended Coaxitron receivers, such as Esprit, Intercept , Spectra, and LRD41C21/LRD41C22 Series, the KBD4002 will support all the functions above, including the setting and calling of presets and patterns. It will not support programming of preset or pattern labels. If labels for presets or patterns are required, they would need to be programmed with a different control, such as the MPT9500.

Camera Setup

section)

IMPORTANT NOTE ABOUT DIFFERENCES IN SIMPLEX AND DUPLEX MULTIPLEXER MODES OF OPERATION

The simplex multiplexer has three modes of operation: live, VCR, and record.

• In the live mode, the main monitor can show live video both in full-screen or multiple-screen views. You cannot record in the live mode. The multiplexer’s DISPLAY/RECORD LED is OFF.

• In the VCR mode, the main monitor will show full-screen or multiple-screen views of videotape playback. You cannot record in the VCR mode. The multiplexer’s DISPLAY/ RECORD LED is OFF.

• In the record mode, the main monitor will show live video of an individual camera in full-screen view only. You can record only when in the record mode. While recording, all cameras are being recorded simultaneously. The multiplexer’s DISPLAY/RECORD LED is ON.

The duplex multiplexer has two modes of operation: live and VCR.

• In the live mode, the main monitor will show live video both in full-screen or multiple-screen views. You can record while in this mode. The multiplexer’s LIVE/VCR LED is ON.

• In the VCR mode, the main monitor will show full-screen or multiple-screen views of videotape playback. You can record in the VCR mode if you have a second VCR connected to the VCR OUT jack on the multiplexer. The multiplexer ’s LIVE/VCR LED is OFF.

Pelco Manual C581M-B (1/04) 9

LIVE/VCR

MONITOR

UNIT MAIN SPOT SEQ VIEW PATTERN PRESET ON OFF

123

456

789

CAM 0 CLEAR

FOCUS

NEAR

FAR

ZOOM

TELE

WIDE

AUX

IRIS

OPEN

KBD4002

PAN / TILT

MADE IN USA

For complete instructions on how to use the keys, refer to Table B, Operation Guide.

* The turbo pan feature

may be disabled. Place switch 6 on the rear panel DIP switch block in the off position. See Figure 1.

1112

1. LED DISPLAY Displays the address of the multiplexer

(from 1-16) with which the keyboard is communicating.

2. LIVE/VCR KEY Selects the source of video to display

on the monitor(s). LIVE is live video from the cameras. VCR is recorded video that is played back from a VCR.

The simplex multiplexer must be in the record mode to record video. Check the main monitor screen to see that it indicates REC. Press the LIVE/VCR key to change modes.

3. ZOOM KEY Zooms in (2X or 4X) on the displayed

camera. Use the pan/tilt keys to control the zoom location.

4. PIP KEY Displays on the main monitor a picture-in-

picture insert on top of the full-screen display.

5. FOUR-CAMERA DISPLAY KEY Press once to

display a group of four cameras on the main monitor. Repeat pressing to display other groups.

6. NINE-CAMERA DISPLAY KEY Press once to

display a group of nine cameras on the main monitor. Press again to display second group.

7. 16-CAMERA DISPLAY KEY Press once to display all

16 cameras on the main monitor.

8. AUXILIARY KEYS Turn receiver auxiliary functions on

and off.

9. PRESET KEY Sends a camera to a preset: Enter the

preset number and then press this key. Also is used for programming presets.

10. PATTERN KEY Press to begin a pattern. Also is used

to program a pattern.

11. PAN/TILT KEYS Provide motion control to receiver and

are used to navigate through the multiplexer programming menus. Variable speed control is accomplished with the number keypad using the “select-a-speed” feature. With select-a-speed, each digit (1-9) represents a relative pan and tilt speed. The number 1 represents the slowest speed available while the number 9 speed equates to turbo pan* (for those receivers capable of supporting turbo pan speed). When the number 9 is entered, the tilt will operate at the number 8 speed. Entering the number 0 sets a mid-range speed.

12. VIEW KEY Press to enter program mode for

multiplexer/multiplexer server.

13. LENS CONTROL KEYS Control camera lens

functions: focus, iris and zoom.

14. SEQ KEY Starts/stops a sequence.

15. CLEAR KEY Press to clear a numeric entry.

16. CAM KEY Selects a camera: Enter the camera number

and then press this key.

17. NUMBER PAD Enter numbers.

18. MONITOR KEYS Select the main or spot monitor for

viewing individual cameras. A green LED above each key indicates which monitor is selected.

19. UNIT KEY Selects the multiplexer with which the

keyboard communicates: Enter the address of the multiplexer (1-16) and then press this key.

Figure 2. KBD4002 Keyboard Definitions

10 Pelco Manual C581M-B (1/04)

Table B. Operation Guide

NOTE:

References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard. There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (switch 7 ON, refer to Table C) or by addressing the cameras in groups of 9 or 16 according to the multiplexer they are connected to (switch 7 OFF); for example, multiplexer 1, cameras 1-9 or 1-16; multiplexer 2, cameras 1-9 or 1-16, etc.

OPERATION KEYBOARD COMMAND RESULT

Use the “select-a-speed” feature to operate pan and tilt units with variable speed.

Call a camera to the MAIN monitor.

Call a camera to the SPOT monitor.

Enter a number, 1-9, from the number keypad followed by one of the pan/tilt keys. Each number represents a relative pan and tilt speed with number 9 equaling turbo pan speed (on equipped receivers) and number 1 equaling crawl speed (the slowest speed). When the number 9 is entered, the tilt will operate at the number 8 speed. Entering the number 0 sets a mid-range speed.

1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.

2. Select the camera.

Addressing by Multiplexer (Switch 7 OFF)

a. On the number pad, press the address number of the

multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.

b. On the number keypad press the number of the

camera (1-16), then press the CAM key.

Addressing Consecutively (Switch 7 ON)

On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.

3. Press the LIVE/VCR key to select the mode of operation.

1. Press the SPOT MONITOR key. The green LED over the SPOT key lights.

The speed that is selected will remain in memory until it is changed.

Stops a sequence if one is in progress. Displays the camera on the MAIN monitor.

Displays the camera on the SPOT monitor.

2. Select the camera.

Addressing by Multiplexer (Switch 7 OFF)

a. On the number pad, press the address number of the

multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.

b. On the number keypad press the number of the

camera (1-16), then press the CAM key.

Addressing Consecutively (Switch 7 ON)

On the number keypad press the number of the camera, then press the CAM key. Refer to Table C for camera numbers.

(Continued on next page)

Pelco Manual C581M-B (1/04) 11

Table B. Operation Guide (Continued)

OPERATION KEYBOARD COMMAND RESULT

Set main tracking.

Exit main tracking.

Call a group of cameras to the MAIN monitor.

1. Go to the Advanced System Setup menu.

2. Press the pan/tilt keys so the cursor highlights SPOT MONITOR DISPLAY items.

3. Press the OPEN key until TRACK MAIN is displayed.

4. Exit the Advanced System Setup menu.

1. Go to the Advanced System Setup menu.

2. Press the pan/tilt keys so the cursor highlights SPOT MONITOR DISPLAY items.

3. Press the OPEN key until either SEQUENCE or BLANK is displayed.

4. Exit the Advanced System Setup menu.

1. Press the MAIN MONITOR key. The green LED over the MAIN key lights.

2. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key. The LED displays the address.

3. Press the key below the 4, 9, or 16 icon.

Spot monitor follows the camera switching that occurs on the main monitor in single screen mode. In multi-screen mode, the spot monitor switches to camera 1.

Allows only P/T/Z control while in main monitor mode. Press the SPOT key to have presets and patterns while in this mode.

Exits main tracking mode.

Displays the group of cameras on the MAIN monitor.

4. Repeat pressing the key until the correct group is displayed (4 or 9 only).

5. Press the LIVE/VCR key to select the mode of operation.

(Continued on next page)

12 Pelco Manual C581M-B (1/04)

+ 28 hidden pages