Pelco FUMS-FFX8, FUMS-FFX4TX4, FUMS-FFX4, FUMS-FFX2TX2, FUMS-FTX8 User Manual

...

INSTALLATION AND OPERATION MANUAL

FUMS-F(FX,TX)(2,4,8)[TX(2,4)] Series

4- OR 8-PORT UNMANAGED ETHERNET SWITCHES

This manual serves the following Model Numbers:

FUMS-FFX8

FUMS-FFX4TX4

FUMS-FTX8

FUMS-FFX4

FUMS-FFX2TX2

FUMS-FTX4

The Pelco Series of four and eight port unmanaged Ethernet switches are designed

to transmit and receive 10/100Mbps data over optical fiber through user selectable

FSFP options or 10/100Mbps data over CAT5E/6 electrical cable. These units

integrate eight independent 10/100Mbps channels in a single package.

The FUMS-FFX4TX4, FUMS-FFX2TX2, FUMS-FTX8 and FUMS-FTX4 require

the ordering of sold-separately interchangeable Pelco FSFP modules for fiber

type, distance and connectors.

All electrical interfaces will Auto-Negotiate to 10Mbps, or 100Mbps Ethernet

rate without any adjustments. The optical interfaces operate at a 100Mbps

Ethernet rate.

The models in this series are environmentally hardened to operate in

demanding environments.

LED indicators are provided for confirming equipment operating status.

These units are interchangeable between stand-alone or card mount

configurations. See Figure A on Page 10 for installation instructions.

See Figures 1 – 14 for complete installation details.

TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981

C3927M-A / REV 07-28-14

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

18. Use only installation methods and materials capable of supporting four times the maximum specified load.

19. Switch does not support Internet Group Management Protocol (IGMP) and should not be used as a core switch.

20. A CCC-approved power cord must be used to power this equipment when used in China.

21. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981 C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 1 – FUMS-FFX4TX4

AND RJ-45

SELECTION OF FSFP MODULES

OPTICAL FIBERS DETERMINED BY

FIGURE 2 – FUMS-FFX4TX4

BLACK WITH WHITE STRIPES BLACK Power Supply: Surface Mount: 8-15 VDC @ 2W Rack Mount: From Rack

NOTE: Remove Electrical

Connector for Rack Mount Units

RE AR PA NELFRONT PANEL